p71924506
/
linux_old1
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity

cpqarray: remove it from the kernel 

We disabled the ability to enable this driver back in October of 2013,
we should be able to safely remove it at this point. The initial goal
was to remove it in 3.15, so now is the time.

Signed-off-by: Jens Axboe <axboe@fb.com>
This commit is contained in:
Jens Axboe 2016-03-14 09:06:01 -06:00
parent 516fdcea0d
commit d436641439
7 changed files with 0 additions and 2491 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

93
Documentation/blockdev/cpqarray.txt
View File

@ -1,93 +0,0 @@
This driver is for Compaq's SMART2 Intelligent Disk Array Controllers.
Supported Cards:
----------------
This driver is known to work with the following cards:
* SMART (EISA)
* SMART-2/E (EISA)
* SMART-2/P
* SMART-2DH
* SMART-2SL
* SMART-221
* SMART-3100ES
* SMART-3200
* Integrated Smart Array Controller
* SA 4200
* SA 4250ES
* SA 431
* RAID LC2 Controller
It should also work with some really old Disk array adapters, but I am
unable to test against these cards:
* IDA
* IDA-2
* IAES
EISA Controllers:
-----------------
If you want to use an EISA controller you'll have to supply some
modprobe/lilo parameters. If the driver is compiled into the kernel, must
give it the controller's IO port address at boot time (it is not
necessary to specify the IRQ). For example, if you had two SMART-2/E
controllers, in EISA slots 1 and 2 you'd give it a boot argument like
this:
smart2=0x1000,0x2000
If you were loading the driver as a module, you'd give load it like this:
modprobe cpqarray eisa=0x1000,0x2000
You can use EISA and PCI adapters at the same time.
Device Naming:
--------------
You need some entries in /dev for the ida device. MAKEDEV in the /dev
directory can make device nodes for you automatically. The device setup is
as follows:
Major numbers:
72 ida0
73 ida1
74 ida2
75 ida3
76 ida4
77 ida5
78 ida6
79 ida7
Minor numbers:
b7 b6 b5 b4 b3 b2 b1 b0
|----+----| |----+----|
| |
| +-------- Partition ID (0=wholedev, 1-15 partition)
|
+-------------------- Logical Volume number
The device naming scheme is:
/dev/ida/c0d0 Controller 0, disk 0, whole device
/dev/ida/c0d0p1 Controller 0, disk 0, partition 1
/dev/ida/c0d0p2 Controller 0, disk 0, partition 2
/dev/ida/c0d0p3 Controller 0, disk 0, partition 3
/dev/ida/c1d1 Controller 1, disk 1, whole device
/dev/ida/c1d1p1 Controller 1, disk 1, partition 1
/dev/ida/c1d1p2 Controller 1, disk 1, partition 2
/dev/ida/c1d1p3 Controller 1, disk 1, partition 3
Changelog:
==========
10-28-2004 : General cleanup, syntax fixes for in-kernel driver version.
James Nelson <james4765@gmail.com>
1999 : Original Document

6
MAINTAINERS
View File

@ -4988,12 +4988,6 @@ T: git git://linuxtv.org/anttip/media_tree.git
S: Maintained
F: drivers/media/dvb-frontends/hd29l2*
HEWLETT-PACKARD SMART2 RAID DRIVER
L: iss_storagedev@hp.com
S: Orphan
F: Documentation/blockdev/cpqarray.txt
F: drivers/block/cpqarray.*
HEWLETT-PACKARD SMART ARRAY RAID DRIVER (hpsa)
M: Don Brace <don.brace@pmcs.com>
L: iss_storagedev@hp.com

10
drivers/block/Kconfig
View File

@ -110,16 +110,6 @@ source "drivers/block/mtip32xx/Kconfig"
source "drivers/block/zram/Kconfig"
config BLK_CPQ_DA
tristate "Compaq SMART2 support"
depends on PCI && VIRT_TO_BUS && 0
help
This is the driver for Compaq Smart Array controllers. Everyone
using these boards should say Y here. See the file
<file:Documentation/blockdev/cpqarray.txt> for the current list of
boards supported by this driver, and for further information on the
use of this driver.
config BLK_CPQ_CISS_DA
tristate "Compaq Smart Array 5xxx support"
depends on PCI

1820
drivers/block/cpqarray.c
View File

File diff suppressed because it is too large Load Diff

126
drivers/block/cpqarray.h
View File

@ -1,126 +0,0 @@
/*
* Disk Array driver for Compaq SMART2 Controllers
* Copyright 1998 Compaq Computer Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or
* NON INFRINGEMENT. See the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
* Questions/Comments/Bugfixes to iss_storagedev@hp.com
*
* If you want to make changes, improve or add functionality to this
* driver, you'll probably need the Compaq Array Controller Interface
* Specificiation (Document number ECG086/1198)
*/
#ifndef CPQARRAY_H
#define CPQARRAY_H
#ifdef __KERNEL__
#include <linux/blkdev.h>
#include <linux/slab.h>
#include <linux/proc_fs.h>
#include <linux/timer.h>
#endif
#include "ida_cmd.h"
#define IO_OK 0
#define IO_ERROR 1
#define NWD 16
#define NWD_SHIFT 4
#define IDA_TIMER (5*HZ)
#define IDA_TIMEOUT (10*HZ)
#define MISC_NONFATAL_WARN 0x01
typedef struct {
unsigned blk_size;
unsigned nr_blks;
unsigned cylinders;
unsigned heads;
unsigned sectors;
int usage_count;
} drv_info_t;
#ifdef __KERNEL__
struct ctlr_info;
typedef struct ctlr_info ctlr_info_t;
struct access_method {
void (*submit_command)(ctlr_info_t *h, cmdlist_t *c);
void (*set_intr_mask)(ctlr_info_t *h, unsigned long val);
unsigned long (*fifo_full)(ctlr_info_t *h);
unsigned long (*intr_pending)(ctlr_info_t *h);
unsigned long (*command_completed)(ctlr_info_t *h);
};
struct board_type {
__u32 board_id;
char *product_name;
struct access_method *access;
};
struct ctlr_info {
int ctlr;
char devname[8];
__u32 log_drv_map;
__u32 drv_assign_map;
__u32 drv_spare_map;
__u32 mp_failed_drv_map;
char firm_rev[4];
int ctlr_sig;
int log_drives;
int phys_drives;
struct pci_dev *pci_dev; /* NULL if EISA */
__u32 board_id;
char *product_name;
void __iomem *vaddr;
unsigned long paddr;
unsigned long io_mem_addr;
unsigned long io_mem_length;
int intr;
int usage_count;
drv_info_t drv[NWD];
struct proc_dir_entry *proc;
struct access_method access;
cmdlist_t *reqQ;
cmdlist_t *cmpQ;
cmdlist_t *cmd_pool;
dma_addr_t cmd_pool_dhandle;
unsigned long *cmd_pool_bits;
struct request_queue *queue;
spinlock_t lock;
unsigned int Qdepth;
unsigned int maxQsinceinit;
unsigned int nr_requests;
unsigned int nr_allocs;
unsigned int nr_frees;
struct timer_list timer;
unsigned int misc_tflags;
};
#define IDA_LOCK(i) (&hba[i]->lock)
#endif
#endif /* CPQARRAY_H */

349
drivers/block/ida_cmd.h
View File

@ -1,349 +0,0 @@
/*
* Disk Array driver for Compaq SMART2 Controllers
* Copyright 1998 Compaq Computer Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or
* NON INFRINGEMENT. See the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
* Questions/Comments/Bugfixes to iss_storagedev@hp.com
*
*/
#ifndef ARRAYCMD_H
#define ARRAYCMD_H
#include <asm/types.h>
#if 0
#include <linux/blkdev.h>
#endif
/* for the Smart Array 42XX cards */
#define S42XX_REQUEST_PORT_OFFSET 0x40
#define S42XX_REPLY_INTR_MASK_OFFSET 0x34
#define S42XX_REPLY_PORT_OFFSET 0x44
#define S42XX_INTR_STATUS 0x30
#define S42XX_INTR_OFF 0x08
#define S42XX_INTR_PENDING 0x08
#define COMMAND_FIFO 0x04
#define COMMAND_COMPLETE_FIFO 0x08
#define INTR_MASK 0x0C
#define INTR_STATUS 0x10
#define INTR_PENDING 0x14
#define FIFO_NOT_EMPTY 0x01
#define FIFO_NOT_FULL 0x02
#define BIG_PROBLEM 0x40
#define LOG_NOT_CONF 2
#pragma pack(1)
typedef struct {
__u32 size;
__u32 addr;
} sg_t;
#define RCODE_NONFATAL 0x02
#define RCODE_FATAL 0x04
#define RCODE_INVREQ 0x10
typedef struct {
__u16 next;
__u8 cmd;
__u8 rcode;
__u32 blk;
__u16 blk_cnt;
__u8 sg_cnt;
__u8 reserved;
} rhdr_t;
#define SG_MAX 32
typedef struct {
rhdr_t hdr;
sg_t sg[SG_MAX];
__u32 bp;
} rblk_t;
typedef struct {
__u8 unit;
__u8 prio;
__u16 size;
} chdr_t;
#define CMD_RWREQ 0x00
#define CMD_IOCTL_PEND 0x01
#define CMD_IOCTL_DONE 0x02
typedef struct cmdlist {
chdr_t hdr;
rblk_t req;
__u32 size;
int retry_cnt;
__u32 busaddr;
int ctlr;
struct cmdlist *prev;
struct cmdlist *next;
struct request *rq;
int type;
} cmdlist_t;
#define ID_CTLR 0x11
typedef struct {
__u8 nr_drvs;
__u32 cfg_sig;
__u8 firm_rev[4];
__u8 rom_rev[4];
__u8 hw_rev;
__u32 bb_rev;
__u32 drv_present_map;
__u32 ext_drv_map;
__u32 board_id;
__u8 cfg_error;
__u32 non_disk_bits;
__u8 bad_ram_addr;
__u8 cpu_rev;
__u8 pdpi_rev;
__u8 epic_rev;
__u8 wcxc_rev;
__u8 marketing_rev;
__u8 ctlr_flags;
__u8 host_flags;
__u8 expand_dis;
__u8 scsi_chips;
__u32 max_req_blocks;
__u32 ctlr_clock;
__u8 drvs_per_bus;
__u16 big_drv_present_map[8];
__u16 big_ext_drv_map[8];
__u16 big_non_disk_map[8];
__u16 task_flags;
__u8 icl_bus;
__u8 red_modes;
__u8 cur_red_mode;
__u8 red_ctlr_stat;
__u8 red_fail_reason;
__u8 reserved[403];
} id_ctlr_t;
typedef struct {
__u16 cyl;
__u8 heads;
__u8 xsig;
__u8 psectors;
__u16 wpre;
__u8 maxecc;
__u8 drv_ctrl;
__u16 pcyls;
__u8 pheads;
__u16 landz;
__u8 sect_per_track;
__u8 cksum;
} drv_param_t;
#define ID_LOG_DRV 0x10
typedef struct {
__u16 blk_size;
__u32 nr_blks;
drv_param_t drv;
__u8 fault_tol;
__u8 reserved;
__u8 bios_disable;
} id_log_drv_t;
#define ID_LOG_DRV_EXT 0x18
typedef struct {
__u32 log_drv_id;
__u8 log_drv_label[64];
__u8 reserved[418];
} id_log_drv_ext_t;
#define SENSE_LOG_DRV_STAT 0x12
typedef struct {
__u8 status;
__u32 fail_map;
__u16 read_err[32];
__u16 write_err[32];
__u8 drv_err_data[256];
__u8 drq_timeout[32];
__u32 blks_to_recover;
__u8 drv_recovering;
__u16 remap_cnt[32];
__u32 replace_drv_map;
__u32 act_spare_map;
__u8 spare_stat;
__u8 spare_repl_map[32];
__u32 repl_ok_map;
__u8 media_exch;
__u8 cache_fail;
__u8 expn_fail;
__u8 unit_flags;
__u16 big_fail_map[8];
__u16 big_remap_map[128];
__u16 big_repl_map[8];
__u16 big_act_spare_map[8];
__u8 big_spar_repl_map[128];
__u16 big_repl_ok_map[8];
__u8 big_drv_rebuild;
__u8 reserved[36];
} sense_log_drv_stat_t;
#define START_RECOVER 0x13
#define ID_PHYS_DRV 0x15
typedef struct {
__u8 scsi_bus;
__u8 scsi_id;
__u16 blk_size;
__u32 nr_blks;
__u32 rsvd_blks;
__u8 drv_model[40];
__u8 drv_sn[40];
__u8 drv_fw[8];
__u8 scsi_iq_bits;
__u8 compaq_drv_stmp;
__u8 last_fail;
__u8 phys_drv_flags;
__u8 phys_drv_flags1;
__u8 scsi_lun;
__u8 phys_drv_flags2;
__u8 reserved;
__u32 spi_speed_rules;
__u8 phys_connector[2];
__u8 phys_box_on_bus;
__u8 phys_bay_in_box;
} id_phys_drv_t;
#define BLINK_DRV_LEDS 0x16
typedef struct {
__u32 blink_duration;
__u32 reserved;
__u8 blink[256];
__u8 reserved1[248];
} blink_drv_leds_t;
#define SENSE_BLINK_LEDS 0x17
typedef struct {
__u32 blink_duration;
__u32 btime_elap;
__u8 blink[256];
__u8 reserved1[248];
} sense_blink_leds_t;
#define IDA_READ 0x20
#define IDA_WRITE 0x30
#define IDA_WRITE_MEDIA 0x31
#define RESET_TO_DIAG 0x40
#define DIAG_PASS_THRU 0x41
#define SENSE_CONFIG 0x50
#define SET_CONFIG 0x51
typedef struct {
__u32 cfg_sig;
__u16 compat_port;
__u8 data_dist_mode;
__u8 surf_an_ctrl;
__u16 ctlr_phys_drv;
__u16 log_unit_phys_drv;
__u16 fault_tol_mode;
__u8 phys_drv_param[16];
drv_param_t drv;
__u32 drv_asgn_map;
__u16 dist_factor;
__u32 spare_asgn_map;
__u8 reserved[6];
__u16 os;
__u8 ctlr_order;
__u8 extra_info;
__u32 data_offs;
__u8 parity_backedout_write_drvs;
__u8 parity_dist_mode;
__u8 parity_shift_fact;
__u8 bios_disable_flag;
__u32 blks_on_vol;
__u32 blks_per_drv;
__u8 scratch[16];
__u16 big_drv_map[8];
__u16 big_spare_map[8];
__u8 ss_source_vol;
__u8 mix_drv_cap_range;
struct {
__u16 big_drv_map[8];
__u32 blks_per_drv;
__u16 fault_tol_mode;
__u16 dist_factor;
} MDC_range[4];
__u8 reserved1[248];
} config_t;
#define BYPASS_VOL_STATE 0x52
#define SS_CREATE_VOL 0x53
#define CHANGE_CONFIG 0x54
#define SENSE_ORIG_CONF 0x55
#define REORDER_LOG_DRV 0x56
typedef struct {
__u8 old_units[32];
} reorder_log_drv_t;
#define LABEL_LOG_DRV 0x57
typedef struct {
__u8 log_drv_label[64];
} label_log_drv_t;
#define SS_TO_VOL 0x58
#define SET_SURF_DELAY 0x60
typedef struct {
__u16 delay;
__u8 reserved[510];
} surf_delay_t;
#define SET_OVERHEAT_DELAY 0x61
typedef struct {
__u16 delay;
} overhead_delay_t;
#define SET_MP_DELAY
typedef struct {
__u16 delay;
__u8 reserved[510];
} mp_delay_t;
#define PASSTHRU_A 0x91
typedef struct {
__u8 target;
__u8 bus;
__u8 lun;
__u32 timeout;
__u32 flags;
__u8 status;
__u8 error;
__u8 cdb_len;
__u8 sense_error;
__u8 sense_key;
__u32 sense_info;
__u8 sense_code;
__u8 sense_qual;
__u32 residual;
__u8 reserved[4];
__u8 cdb[12];
} scsi_param_t;
#define RESUME_BACKGROUND_ACTIVITY 0x99
#define SENSE_CONTROLLER_PERFORMANCE 0xa8
#define FLUSH_CACHE 0xc2
#define COLLECT_BUFFER 0xd2
#define READ_FLASH_ROM 0xf6
#define WRITE_FLASH_ROM 0xf7
#pragma pack()
#endif /* ARRAYCMD_H */

87
drivers/block/ida_ioctl.h
View File

@ -1,87 +0,0 @@
/*
* Disk Array driver for Compaq SMART2 Controllers
* Copyright 1998 Compaq Computer Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or
* NON INFRINGEMENT. See the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
* Questions/Comments/Bugfixes to iss_storagedev@hp.com
*
*/
#ifndef IDA_IOCTL_H
#define IDA_IOCTL_H
#include "ida_cmd.h"
#include "cpqarray.h"
#define IDAGETDRVINFO 0x27272828
#define IDAPASSTHRU 0x28282929
#define IDAGETCTLRSIG 0x29293030
#define IDAREVALIDATEVOLS 0x30303131
#define IDADRIVERVERSION 0x31313232
#define IDAGETPCIINFO 0x32323333
typedef struct _ida_pci_info_struct
{
unsigned char bus;
unsigned char dev_fn;
__u32 board_id;
} ida_pci_info_struct;
/*
* Normally, the ioctl determines the logical unit for this command by
* the major,minor number of the fd passed to ioctl. If you need to send
* a command to a different/nonexistant unit (such as during config), you
* can override the normal behavior by setting the unit valid bit. (Normally,
* it should be zero) The controller the command is sent to is still
* determined by the major number of the open device.
*/
#define UNITVALID 0x80
typedef struct {
__u8 cmd;
__u8 rcode;
__u8 unit;
__u32 blk;
__u16 blk_cnt;
/* currently, sg_cnt is assumed to be 1: only the 0th element of sg is used */
struct {
void __user *addr;
size_t size;
} sg[SG_MAX];
int sg_cnt;
union ctlr_cmds {
drv_info_t drv;
unsigned char buf[1024];
id_ctlr_t id_ctlr;
drv_param_t drv_param;
id_log_drv_t id_log_drv;
id_log_drv_ext_t id_log_drv_ext;
sense_log_drv_stat_t sense_log_drv_stat;
id_phys_drv_t id_phys_drv;
blink_drv_leds_t blink_drv_leds;
sense_blink_leds_t sense_blink_leds;
config_t config;
reorder_log_drv_t reorder_log_drv;
label_log_drv_t label_log_drv;
surf_delay_t surf_delay;
overhead_delay_t overhead_delay;
mp_delay_t mp_delay;
scsi_param_t scsi_param;
} c;
} ida_ioctl_t;
#endif /* IDA_IOCTL_H */