sysfb device behaviour when removing conflicting framebuffers
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCYr1PfgAKCRDj7w1vZxhR
xVJiAQCMUB/piHXb2eOlMqIu2VamJFvoZdZhoXBzgYq1Eyb4CgD/ZKDPIdkbJTmI
PIFinHqTAFseH7nt3S2XwI90z8qpuQE=
=8hWP
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2022-06-30' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
A NULL pointer dereference fix for vc4, and 3 patches to improve the
sysfb device behaviour when removing conflicting framebuffers
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630072404.2fa4z3nk5h5q34ci@houat
This can be used by subsystems to unregister a platform device registered
by sysfb and also to disable future platform device registration in sysfb.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220607182338.344270-3-javierm@redhat.com
The filenames were changed a while ago, but board.rst, consumer.rst and
intro.rst still refer to the old names. Fix those references to match the
Actual names and avoid possible confusion.
Signed-off-by: Tom Schwindl <schwindl@posteo.de>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
The hardware timestamp engine documentation is driver API material, and
really belongs in the driver-API book; move it there.
Cc: Thierry Reding <treding@nvidia.com>
Acked-by: Dipen Patel <dipenp@nvidia.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Here is the set of driver core changes for 5.19-rc1.
Note, I'm not really happy with this pull request as-is, see below for
details, but overall this is all good for everything but a small set of
systems, which we have a fix for already.
Lots of tiny driver core changes and cleanups happened this cycle,
but the two major things were:
- firmware_loader reorganization and additions including the
ability to have XZ compressed firmware images and the ability
for userspace to initiate the firmware load when it needs to,
instead of being always initiated by the kernel. FPGA devices
specifically want this ability to have their firmware changed
over the lifetime of the system boot, and this allows them to
work without having to come up with yet-another-custom-uapi
interface for loading firmware for them.
- physical location support added to sysfs so that devices that
know this information, can tell userspace where they are
located in a common way. Some ACPI devices already support
this today, and more bus types should support this in the
future.
Smaller changes included:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten any
linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request if you want to take them directly, _OR_ I can just revert
the probe timeout changes and they can wait for the next -rc1 merge
cycle. Given that the fixes are tested, and pretty simple, I'm leaning
toward that choice. Sorry this all came at the end of the merge window,
I should have resolved this all 2 weeks ago, that's my fault as it was
in the middle of some travel for me.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time outs.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnv/A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk/fACgvmenbo5HipqyHnOmTQlT50xQ9EYAn2eTq6ai
GkjLXBGNWOPBa5cU52qf
=yEi/
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.19-rc1.
Lots of tiny driver core changes and cleanups happened this cycle, but
the two major things are:
- firmware_loader reorganization and additions including the ability
to have XZ compressed firmware images and the ability for userspace
to initiate the firmware load when it needs to, instead of being
always initiated by the kernel. FPGA devices specifically want this
ability to have their firmware changed over the lifetime of the
system boot, and this allows them to work without having to come up
with yet-another-custom-uapi interface for loading firmware for
them.
- physical location support added to sysfs so that devices that know
this information, can tell userspace where they are located in a
common way. Some ACPI devices already support this today, and more
bus types should support this in the future.
Smaller changes include:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten
any linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time-outs"
* tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
driver core: fix deadlock in __device_attach
kernfs: Separate kernfs_pr_cont_buf and rename_lock.
topology: Remove unused cpu_cluster_mask()
driver core: Extend deferred probe timeout on driver registration
MAINTAINERS: add Russ Weight as a firmware loader maintainer
driver: base: fix UAF when driver_attach failed
test_firmware: fix end of loop test in upload_read_show()
driver core: location: Add "back" as a possible output for panel
driver core: location: Free struct acpi_pld_info *pld
driver core: Add "*" wildcard support to driver_async_probe cmdline param
driver core: location: Check for allocations failure
arch_topology: Trace the update thermal pressure
kernfs: Rename kernfs_put_open_node to kernfs_unlink_open_file.
export: fix string handling of namespace in EXPORT_SYMBOL_NS
rpmsg: use local 'dev' variable
rpmsg: Fix calling device_lock() on non-initialized device
firmware_loader: describe 'module' parameter of firmware_upload_register()
firmware_loader: Move definitions from sysfs_upload.h to sysfs.h
firmware_loader: Fix configs for sysfs split
selftests: firmware: Add firmware upload selftests
...
Here is the big set of tty and serial driver updates for 5.19-rc1.
Lots of tiny cleanups in here, the major stuff is:
- termbit cleanups and unification by Ilpo. A much needed
change that goes a long way to making things simpler for all
of the different arches
- tty documentation cleanups and movements to their own place in
the documentation tree
- old tty driver cleanups and fixes from Jiri to bring some
existing drivers into the modern world
- RS485 cleanups and unifications to make it easier for
individual drivers to support this mode instead of having to
duplicate logic in each driver
- Lots of 8250 driver updates and additions
- new device id additions
- n_gsm continued fixes and cleanups
- other minor serial driver updates and cleanups
All of these have been in linux-next for weeks with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpndTg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykFegCgizjLDyOepr72zMDWWdp0bBTekz8AoMWODfJY
vB8/kzu329DImJMFB8ET
=rmv0
-----END PGP SIGNATURE-----
Merge tag 'tty-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.19-rc1.
Lots of tiny cleanups in here, the major stuff is:
- termbit cleanups and unification by Ilpo. A much needed change that
goes a long way to making things simpler for all of the different
arches
- tty documentation cleanups and movements to their own place in the
documentation tree
- old tty driver cleanups and fixes from Jiri to bring some existing
drivers into the modern world
- RS485 cleanups and unifications to make it easier for individual
drivers to support this mode instead of having to duplicate logic
in each driver
- Lots of 8250 driver updates and additions
- new device id additions
- n_gsm continued fixes and cleanups
- other minor serial driver updates and cleanups
All of these have been in linux-next for weeks with no reported issues"
* tag 'tty-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (166 commits)
tty: Rework receive flow control char logic
pcmcia: synclink_cs: Don't allow CS5-6
serial: stm32-usart: Correct CSIZE, bits, and parity
serial: st-asc: Sanitize CSIZE and correct PARENB for CS7
serial: sifive: Sanitize CSIZE and c_iflag
serial: sh-sci: Don't allow CS5-6
serial: txx9: Don't allow CS5-6
serial: rda-uart: Don't allow CS5-6
serial: digicolor-usart: Don't allow CS5-6
serial: uartlite: Fix BRKINT clearing
serial: cpm_uart: Fix build error without CONFIG_SERIAL_CPM_CONSOLE
serial: core: Do stop_rx in suspend path for console if console_suspend is disabled
tty: serial: qcom-geni-serial: Remove uart frequency table. Instead, find suitable frequency with call to clk_round_rate.
dt-bindings: serial: renesas,em-uart: Add RZ/V2M clock to access the registers
serial: 8250_fintek: Check SER_RS485_RTS_* only with RS485
Revert "serial: 8250_mtk: Make sure to select the right FEATURE_SEL"
serial: msm_serial: disable interrupts in __msm_console_write()
serial: meson: acquire port->lock in startup()
serial: 8250_dw: Use dev_err_probe()
serial: 8250_dw: Use devm_add_action_or_reset()
...
- Improvements to mlx5 vfio-pci variant driver, including support
for parallel migration per PF (Yishai Hadas)
- Remove redundant iommu_present() check (Robin Murphy)
- Ongoing refactoring to consolidate the VFIO driver facing API
to use vfio_device (Jason Gunthorpe)
- Use drvdata to store vfio_device among all vfio-pci and variant
drivers (Jason Gunthorpe)
- Remove redundant code now that IOMMU core manages group DMA
ownership (Jason Gunthorpe)
- Remove vfio_group from external API handling struct file ownership
(Jason Gunthorpe)
- Correct typo in uapi comments (Thomas Huth)
- Fix coccicheck detected deadlock (Wan Jiabing)
- Use rwsem to remove races and simplify code around container and
kvm association to groups (Jason Gunthorpe)
- Harden access to devices in low power states and use runtime PM to
enable d3cold support for unused devices (Abhishek Sahu)
- Fix dma_owner handling of fake IOMMU groups (Jason Gunthorpe)
- Set driver_managed_dma on vfio-pci variant drivers (Jason Gunthorpe)
- Pass KVM pointer directly rather than via notifier (Matthew Rosato)
-----BEGIN PGP SIGNATURE-----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=etEI
-----END PGP SIGNATURE-----
Merge tag 'vfio-v5.19-rc1' of https://github.com/awilliam/linux-vfio
Pull vfio updates from Alex Williamson:
- Improvements to mlx5 vfio-pci variant driver, including support for
parallel migration per PF (Yishai Hadas)
- Remove redundant iommu_present() check (Robin Murphy)
- Ongoing refactoring to consolidate the VFIO driver facing API to use
vfio_device (Jason Gunthorpe)
- Use drvdata to store vfio_device among all vfio-pci and variant
drivers (Jason Gunthorpe)
- Remove redundant code now that IOMMU core manages group DMA ownership
(Jason Gunthorpe)
- Remove vfio_group from external API handling struct file ownership
(Jason Gunthorpe)
- Correct typo in uapi comments (Thomas Huth)
- Fix coccicheck detected deadlock (Wan Jiabing)
- Use rwsem to remove races and simplify code around container and kvm
association to groups (Jason Gunthorpe)
- Harden access to devices in low power states and use runtime PM to
enable d3cold support for unused devices (Abhishek Sahu)
- Fix dma_owner handling of fake IOMMU groups (Jason Gunthorpe)
- Set driver_managed_dma on vfio-pci variant drivers (Jason Gunthorpe)
- Pass KVM pointer directly rather than via notifier (Matthew Rosato)
* tag 'vfio-v5.19-rc1' of https://github.com/awilliam/linux-vfio: (38 commits)
vfio: remove VFIO_GROUP_NOTIFY_SET_KVM
vfio/pci: Add driver_managed_dma to the new vfio_pci drivers
vfio: Do not manipulate iommu dma_owner for fake iommu groups
vfio/pci: Move the unused device into low power state with runtime PM
vfio/pci: Virtualize PME related registers bits and initialize to zero
vfio/pci: Change the PF power state to D0 before enabling VFs
vfio/pci: Invalidate mmaps and block the access in D3hot power state
vfio: Change struct vfio_group::container_users to a non-atomic int
vfio: Simplify the life cycle of the group FD
vfio: Fully lock struct vfio_group::container
vfio: Split up vfio_group_get_device_fd()
vfio: Change struct vfio_group::opened from an atomic to bool
vfio: Add missing locking for struct vfio_group::kvm
kvm/vfio: Fix potential deadlock problem in vfio
include/uapi/linux/vfio.h: Fix trivial typo - _IORW should be _IOWR instead
vfio/pci: Use the struct file as the handle not the vfio_group
kvm/vfio: Remove vfio_group from kvm
vfio: Change vfio_group_set_kvm() to vfio_file_set_kvm()
vfio: Change vfio_external_check_extension() to vfio_file_enforced_coherent()
vfio: Remove vfio_external_group_match_file()
...
Quite a large number of conversions this time around, courtesy of Uwe
who has been working tirelessly on these. No drivers of the legacy API
are left at this point, so as a next step the old API can be removed.
Support is added for a few new devices such as the Xilinx AXI timer-
based PWMs and the PWM IP found on Sunplus SoCs.
Other than that, there's a number of fixes, cleanups and optimizations.
-----BEGIN PGP SIGNATURE-----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=CwnJ
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Quite a large number of conversions this time around, courtesy of Uwe
who has been working tirelessly on these. No drivers of the legacy API
are left at this point, so as a next step the old API can be removed.
Support is added for a few new devices such as the Xilinx AXI timer-
based PWMs and the PWM IP found on Sunplus SoCs.
Other than that, there's a number of fixes, cleanups and optimizations"
* tag 'pwm/for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (43 commits)
pwm: pwm-cros-ec: Add channel type support
dt-bindings: google,cros-ec-pwm: Add the new -type compatible
dt-bindings: Add mfd/cros_ec definitions
pwm: Document that the pinstate of a disabled PWM isn't reliable
pwm: twl-led: Implement .apply() callback
pwm: lpc18xx: Implement .apply() callback
pwm: mediatek: Implement .apply() callback
pwm: lpc32xx: Implement .apply() callback
pwm: tegra: Implement .apply() callback
pwm: stmpe: Implement .apply() callback
pwm: sti: Implement .apply() callback
pwm: pwm-mediatek: Add support for MediaTek Helio X10 MT6795
dt-bindings: pwm: pwm-mediatek: Add documentation for MT6795 SoC
pwm: tegra: Optimize period calculation
pwm: renesas-tpu: Improve precision of period and duty_cycle calculation
pwm: renesas-tpu: Improve maths to compute register settings
pwm: renesas-tpu: Rename variables to match the usual naming
pwm: renesas-tpu: Implement .apply() callback
pwm: renesas-tpu: Make use of devm functions
pwm: renesas-tpu: Make use of dev_err_probe()
...
New support:
- Tegra gpcdma Driver support
- Qualcomm SM8350, Sm8450 and SC7280 Device support
- Renesas RZN1 dma and platform support
Updates:
- stm32 device pause/resume support and updates
- DMA memset ops Documentation and usage clarification
- Deprecate '#dma-channels' & '#dma-requests' bindings
- Driver updates for stm32, ptdma idsx etc
-----BEGIN PGP SIGNATURE-----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=ANxH
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"Nothing special, this includes a couple of new device support and new
driver support and bunch of driver updates.
New support:
- Tegra gpcdma driver support
- Qualcomm SM8350, Sm8450 and SC7280 device support
- Renesas RZN1 dma and platform support
Updates:
- stm32 device pause/resume support and updates
- DMA memset ops Documentation and usage clarification
- deprecate '#dma-channels' & '#dma-requests' bindings
- driver updates for stm32, ptdma idsx etc"
* tag 'dmaengine-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (87 commits)
dmaengine: idxd: make idxd_wq_enable() return 0 if wq is already enabled
dmaengine: sun6i: Add support for the D1 variant
dmaengine: sun6i: Add support for 34-bit physical addresses
dmaengine: sun6i: Do not use virt_to_phys
dt-bindings: dma: sun50i-a64: Add compatible for D1
dmaengine: tegra: Remove unused switch case
dmaengine: tegra: Fix uninitialized variable usage
dmaengine: stm32-dma: add device_pause/device_resume support
dmaengine: stm32-dma: rename pm ops before dma pause/resume introduction
dmaengine: stm32-dma: pass DMA_SxSCR value to stm32_dma_handle_chan_done()
dmaengine: stm32-dma: introduce stm32_dma_sg_inc to manage chan->next_sg
dmaengine: stm32-dmamux: avoid reset of dmamux if used by coprocessor
dmaengine: qcom: gpi: Add support for sc7280
dt-bindings: dma: pl330: Add power-domains
dmaengine: stm32-mdma: use dev_dbg on non-busy channel spurious it
dmaengine: stm32-mdma: fix chan initialization in stm32_mdma_irq_handler()
dmaengine: stm32-mdma: remove GISR1 register
dmaengine: ti: deprecate '#dma-channels'
dmaengine: mmp: deprecate '#dma-channels'
dmaengine: pxa: deprecate '#dma-channels' and '#dma-requests'
...
Core changes:
- New helpers from Andy such as for_each_gpiochip_node() affecting both
GPIO and pin control, improving a bunch of drivers in the process.
- Pulled in Marc Zyngiers work to make IRQ chips immutable, and started
to apply fixups on top.
New drivers:
- New driver for Marvell MVEBU 98DX2530.
- New driver for Mediatek MT8195.
- Support Qualcomm PMX65 and PM6125.
- New driver for Qualcomm SC7280 LPASS pin control.
- New driver for Rockchip RK3588.
- New driver for NXP Freescale i.MXRT1170.
- New driver for Mediatek MT6795 Helio X10.
Improvements:
- Several Aspeed G6 cleanups and non-critical fixes.
- Thorought refactoring of some of the ever improving Renesas drivers.
- Clean up Mediatek MT8192 bindings a bit.
- PWM output and clock monitoring in the Ocelot LAN966x driver.
- Thorough refactoring and cleanup of the Ralink drivers such as
RT2880, RT3883, RT305X, MT7620, MT7621, MT7628 splitting these into proper
sub-drivers.
-----BEGIN PGP SIGNATURE-----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=e5GM
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Pretty big this time. Mostly due to (nice) Renesas refactorings.
Core changes:
- New helpers from Andy such as for_each_gpiochip_node() affecting
both GPIO and pin control, improving a bunch of drivers in the
process.
- Pulled in Marc Zyngiers work to make IRQ chips immutable, and
started to apply fixups on top.
New drivers:
- New driver for Marvell MVEBU 98DX2530.
- New driver for Mediatek MT8195.
- Support Qualcomm PMX65 and PM6125.
- New driver for Qualcomm SC7280 LPASS pin control.
- New driver for Rockchip RK3588.
- New driver for NXP Freescale i.MXRT1170.
- New driver for Mediatek MT6795 Helio X10.
Improvements:
- Several Aspeed G6 cleanups and non-critical fixes.
- Thorought refactoring of some of the ever improving Renesas
drivers.
- Clean up Mediatek MT8192 bindings a bit.
- PWM output and clock monitoring in the Ocelot LAN966x driver.
- Thorough refactoring and cleanup of the Ralink drivers such as
RT2880, RT3883, RT305X, MT7620, MT7621, MT7628 splitting these into
proper sub-drivers"
* tag 'pinctrl-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (161 commits)
pinctrl: apple: Use a raw spinlock for the regmap
pinctrl: berlin: bg4ct: Use devm_platform_*ioremap_resource() APIs
pinctrl: intel: Fix kernel doc format, i.e. add return sections
dt-bindings: pinctrl: qcom: Drop 'maxItems' on 'wakeup-parent'
pinctrl: starfive: Make the irqchip immutable
pinctrl: mediatek: Add pinctrl driver for MT6795 Helio X10
dt-bindings: pinctrl: Add MediaTek MT6795 pinctrl bindings
pinctrl: freescale: Add i.MXRT1170 pinctrl driver support
dt-bindings: pinctrl: add i.MXRT1170 pinctrl Documentation
dt-bindings: pinctrl: rockchip: increase max amount of device functions
dt-bindings: pinctrl: qcom,pmic-gpio: add 'gpio-reserved-ranges'
dt-bindings: pinctrl: qcom,pmic-gpio: add 'input-disable'
dt-bindings: pinctrl: qcom,pmic-gpio: describe gpio-line-names
dt-bindings: pinctrl: qcom,pmic-gpio: fix matching pin config
dt-bindings: pinctrl: qcom,pmic-gpio: document PM8150L and PMM8155AU
pinctrl: qcom: spmi-gpio: Add pm6125 compatible
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm6125 compatible
pinctrl: intel: Drop unused irqchip member in struct intel_pinctrl
pinctrl: intel: make irq_chip immutable
pinctrl: cherryview: Use GPIO chip pointer in chv_gpio_irq_mask_unmask()
...
- After a long period of inactivity, the Japanese translations are seeing
some much-needed maintenance and updating.
- Reworked IOMMU documentation
- Some new documentation for static-analysis tools
- A new overall structure for the memory-management documentation. This
is an LSFMM outcome that, it is hoped, will help encourage developers to
fill in the many gaps. Optimism is eternal...but hopefully it will
work.
- More Chinese translations.
Plus the usual typo fixes, updates, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAmKLqZQPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YdgQH/2/9+EgQDes93f/+iKtbO23EV67392dwrmXS
kYg8lR4948/Q3jzgMloUo6hNOoxXeV/sqmdHu0LjUhFN+BGsp9fFjd/jp0XhWcqA
nnc9foGbpmeFPxHeAg2aqV84eeasLoO5lUUm2rNoPBLd6HFV+IYC5R4VZ+w42StB
5bYEOYwHXMvQZXkivZDse82YmvQK3/2rRGTUoFhME/Aap6rFgWJJ+XQcSKA7WmwW
OpJqq+FOsjsxHe6IFVy6onzlqgGJM8zM2bLtqedid6yaE3uACcHMb/OyAjp0rdKF
BQvaG+d3f7DugABqM6Y1oU75iBtJWWYgGeAm36JtX+3mz2uR/f0=
=3UoR
-----END PGP SIGNATURE-----
Merge tag 'docs-5.19' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"It was a moderately busy cycle for documentation; highlights include:
- After a long period of inactivity, the Japanese translations are
seeing some much-needed maintenance and updating.
- Reworked IOMMU documentation
- Some new documentation for static-analysis tools
- A new overall structure for the memory-management documentation.
This is an LSFMM outcome that, it is hoped, will help encourage
developers to fill in the many gaps. Optimism is eternal...but
hopefully it will work.
- More Chinese translations.
Plus the usual typo fixes, updates, etc"
* tag 'docs-5.19' of git://git.lwn.net/linux: (70 commits)
docs: pdfdocs: Add space for chapter counts >= 100 in TOC
docs/zh_CN: Add dev-tools/gdb-kernel-debugging.rst Chinese translation
input: Docs: correct ntrig.rst typo
input: Docs: correct atarikbd.rst typos
MAINTAINERS: Become the docs/zh_CN maintainer
docs/zh_CN: fix devicetree usage-model translation
mm,doc: Add new documentation structure
Documentation: drop more IDE boot options and ide-cd.rst
Documentation/process: use scripts/get_maintainer.pl on patches
MAINTAINERS: Add entry for DOCUMENTATION/JAPANESE
docs/trans/ja_JP/howto: Don't mention specific kernel versions
docs/ja_JP/SubmittingPatches: Request summaries for commit references
docs/ja_JP/SubmittingPatches: Add Suggested-by as a standard signature
docs/ja_JP/SubmittingPatches: Randy has moved
docs/ja_JP/SubmittingPatches: Suggest the use of scripts/get_maintainer.pl
docs/ja_JP/SubmittingPatches: Update GregKH links
Documentation/sysctl: document max_rcu_stall_to_panic
Documentation: add missing angle bracket in cgroup-v2 doc
Documentation: dev-tools: use literal block instead of code-block
docs/zh_CN: add vm numa translation
...
-----BEGIN PGP SIGNATURE-----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=HllR
-----END PGP SIGNATURE-----
Merge tag 'media/v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- dvb-usb drivers entries got reworked to avoid usage of magic numbers
to refer to data position inside tables
- vcodec driver has gained support for MT8186 and for vp8 and vp9
stateless codecs
- hantro has gained support for Hantro G1 on RK366x
- Added more h264 levels on coda960
- ccs gained support for MIPI CSI-2 28 bits per pixel raw data type
- venus driver gained support for Qualcomm custom compressed pixel
formats
- lots of driver fixes and updates
* tag 'media/v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (308 commits)
media: hantro: Enable HOLD_CAPTURE_BUF for H.264
media: hantro: Add H.264 field decoding support
media: hantro: h264: Make dpb entry management more robust
media: hantro: Stop using H.264 parameter pic_num
media: rkvdec: Enable capture buffer holding for H264
media: rkvdec-h264: Add field decoding support
media: rkvdec: Ensure decoded resolution fit coded resolution
media: rkvdec: h264: Fix reference frame_num wrap for second field
media: rkvdec: h264: Validate and use pic width and height in mbs
media: rkvdec: Move H264 SPS validation in rkvdec-h264
media: rkvdec: h264: Fix bit depth wrap in pps packet
media: rkvdec: h264: Fix dpb_valid implementation
media: rkvdec: Stop overclocking the decoder
media: v4l2: Reorder field reflist
media: h264: Sort p/b reflist using frame_num
media: v4l2: Trace calculated p/b0/b1 initial reflist
media: h264: Store all fields into the unordered list
media: h264: Store current picture fields
media: h264: Increase reference lists size to 32
media: h264: Use v4l2_h264_reference for reflist
...
Core code:
- Make the managed interrupts more robust by shutting them down in the
core code when the assigned affinity mask does not contain online
CPUs.
- Make the irq simulator chip work on RT
- A small set of cpumask and power manageent cleanups
Drivers:
- A set of changes which mark GPIO interrupt chips immutable to prevent
the GPIO subsystem from modifying it under the hood. This provides
the necessary infrastructure and converts a set of GPIO and pinctrl
drivers over.
- A set of changes to make the pseudo-NMI handling for GICv3 more
robust: a missing barrier and consistent handling of the priority
mask.
- Another set of GICv3 improvements and fixes, but nothing outstanding
- The usual set of improvements and cleanups all over the place
- No new irqchip drivers and not even a new device tree binding!
100+ interrupt chips are truly enough.
-----BEGIN PGP SIGNATURE-----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=xcXv
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2022-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt handling updates from Thomas Gleixner:
"Core code:
- Make the managed interrupts more robust by shutting them down in
the core code when the assigned affinity mask does not contain
online CPUs.
- Make the irq simulator chip work on RT
- A small set of cpumask and power manageent cleanups
Drivers:
- A set of changes which mark GPIO interrupt chips immutable to
prevent the GPIO subsystem from modifying it under the hood. This
provides the necessary infrastructure and converts a set of GPIO
and pinctrl drivers over.
- A set of changes to make the pseudo-NMI handling for GICv3 more
robust: a missing barrier and consistent handling of the priority
mask.
- Another set of GICv3 improvements and fixes, but nothing
outstanding
- The usual set of improvements and cleanups all over the place
- No new irqchip drivers and not even a new device tree binding!
100+ interrupt chips are truly enough"
* tag 'irq-core-2022-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
irqchip: Add Kconfig symbols for sunxi drivers
irqchip/gic-v3: Fix priority mask handling
irqchip/gic-v3: Refactor ISB + EOIR at ack time
irqchip/gic-v3: Ensure pseudo-NMIs have an ISB between ack and handling
genirq/irq_sim: Make the irq_work always run in hard irq context
irqchip/armada-370-xp: Do not touch Performance Counter Overflow on A375, A38x, A39x
irqchip/gic: Improved warning about incorrect type
irqchip/csky: Return true/false (not 1/0) from bool functions
irqchip/imx-irqsteer: Add runtime PM support
irqchip/imx-irqsteer: Constify irq_chip struct
irqchip/armada-370-xp: Enable MSI affinity configuration
irqchip/aspeed-scu-ic: Fix irq_of_parse_and_map() return value
irqchip/aspeed-i2c-ic: Fix irq_of_parse_and_map() return value
irqchip/sun6i-r: Use NULL for chip_data
irqchip/xtensa-mx: Fix initial IRQ affinity in non-SMP setup
irqchip/exiu: Fix acknowledgment of edge triggered interrupts
irqchip/gic-v3: Claim iomem resources
dt-bindings: interrupt-controller: arm,gic-v3: Make the v2 compat requirements explicit
irqchip/gic-v3: Relax polling of GIC{R,D}_CTLR.RWP
irqchip/gic-v3: Detect LPI invalidation MMIO registers
...
* Fix immutable IRQ chip examples in the GPIO documentation
* Make use of immutable IRQ chip in Intel pin control drivers
* Add module alias for Intel Apollo Lake
The following is an automated git shortlog grouped by driver:
baytrail:
- make irq_chip immutable
broxton:
- Add module alias for Intel Apollo Lake
cherryview:
- Use GPIO chip pointer in chv_gpio_irq_mask_unmask()
- make irq_chip immutable
Documentation:
- gpio: Advertise irqd_to_hwirq() helper in the examples
- gpio: Fix IRQ mask and unmask examples
intel:
- Fix kernel doc format, i.e. add return sections
- Drop unused irqchip member in struct intel_pinctrl
- make irq_chip immutable
lynxpoint:
- make irq_chip immutable
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSu93Raj3rZDNXzGZv7cr9lmVa5zAUCYoe2dQAKCRD7cr9lmVa5
zOdhAQCRJVUM4CegYK0d3xFyFjePUYACxY9YJuZrNtM0Tqh+iAEAzFD1tTPTxn5X
1FLWz9MAHyMfbZijxU67HyATbGJyAg0=
=9j0f
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.19-2' of gitolite.kernel.org:pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.19-2
* Fix immutable IRQ chip examples in the GPIO documentation
* Make use of immutable IRQ chip in Intel pin control drivers
* Add module alias for Intel Apollo Lake
The following is an automated git shortlog grouped by driver:
baytrail:
- make irq_chip immutable
broxton:
- Add module alias for Intel Apollo Lake
cherryview:
- Use GPIO chip pointer in chv_gpio_irq_mask_unmask()
- make irq_chip immutable
Documentation:
- gpio: Advertise irqd_to_hwirq() helper in the examples
- gpio: Fix IRQ mask and unmask examples
intel:
- Fix kernel doc format, i.e. add return sections
- Drop unused irqchip member in struct intel_pinctrl
- make irq_chip immutable
lynxpoint:
- make irq_chip immutable
Some (most?) drivers emit the inactive state when the PWM is disabled.
However there are exceptions, so document that a consumer better doesn't
depend on this behaviour.
Some known exceptions:
- imx27 emits 0 independent of the configured polarity
- mxs just drives the output to the last emitted state.
- iqs620a makes the output tristated on disable, so an external
pull-down would be required.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Document that drivers must first initialise a media device before
registering it, and clean up once the media device is unregistered.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Instead of direct dereferencing the IRQ data in order to get HW IRQ number
use the irqd_to_hwirq() helper.
Fixes: 5644b66a9c ("Documentation: Update the recommended pattern for GPIO irqchips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
After switching to immutable IRQ chips for GPIO drivers the examples become
uncompilable due to wrong IRQ API, i.e. irq_desc_get_handler_data() in use.
Replace it with proper irq_data_get_irq_chip_data() call where it applies.
Fixes: 5644b66a9c ("Documentation: Update the recommended pattern for GPIO irqchips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Every caller has a readily available vfio_device pointer, use that instead
of passing in a generic struct device. The struct vfio_device already
contains the group we need so this avoids complexity, extra refcountings,
and a confusing lifecycle model.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/3-v4-8045e76bf00b+13d-vfio_mdev_no_group_jgg@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Need to bring commit d8bb92e70a ("drm/dp: Factor out a function to
probe a DPCD address") back as a dependency to further work in
drm-intel-next.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add additional sysfs nodes to monitor the transfer of firmware upload data
to the target device:
cancel: Write 1 to cancel the data transfer
error: Display error status for a failed firmware upload
remaining_size: Display the remaining amount of data to be transferred
status: Display the progress of the firmware upload
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Tianfei zhang <tianfei.zhang@intel.com>
Tested-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20220421212204.36052-6-russell.h.weight@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the firmware subsystem to support a persistent sysfs interface that
userspace may use to initiate a firmware update. For example, FPGA based
PCIe cards load firmware and FPGA images from local FLASH when the card
boots. The images in FLASH may be updated with new images provided by the
user at his/her convenience.
A device driver may call firmware_upload_register() to expose persistent
"loading" and "data" sysfs files. These files are used in the same way as
the fallback sysfs "loading" and "data" files. When 0 is written to
"loading" to complete the write of firmware data, the data is transferred
to the lower-level driver using pre-registered call-back functions. The
data transfer is done in the context of a kernel worker thread.
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Tianfei zhang <tianfei.zhang@intel.com>
Tested-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20220421212204.36052-5-russell.h.weight@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new optional callback is called when the adapter is fully configured
or fully unconfigured. Some drivers may have to take action when this
happens.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The last useful member in this struct is the supported_type_groups, move
it to the mdev_driver and delete mdev_parent_ops.
Replace it with mdev_driver as an argument to mdev_register_device()
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220411141403.86980-33-hch@lst.de
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
Now that all mdev drivers directly create their own mdev_device driver and
directly register with the vfio core's vfio_device_ops this is all dead
code.
Delete vfio_mdev.c and the mdev_parent_ops members that are connected to
it.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220411141403.86980-31-hch@lst.de
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
The commit below causes the following warnings:
Documentation/driver-api/index.rst:14: WARNING: toctree contains reference to nonexisting document 'driver-api/tty'
Documentation/driver-api/tty/index.rst: WARNING: document isn't included in any toctree
This is because I omitted the "/index" part from the link. That part is
needed for directories and I was confused by the surrounding links which
are links to files. Fix it in this patch.
Fixes: b96cd8b05e ("Documentation: move tty to driver-api")
Cc: Jonathan Corbet <corbet@lwn.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220419074302.29632-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* irq/gpio-immutable:
: .
: First try at preventing the GPIO subsystem from abusing irq_chip
: data structures. The general idea is to have an irq_chip flag
: to tell the GPIO subsystem that these structures are immutable,
: and to convert drivers one by one.
: .
Documentation: Update the recommended pattern for GPIO irqchips
gpio: Update TODO to mention immutable irq_chip structures
pinctrl: amd: Make the irqchip immutable
pinctrl: msmgpio: Make the irqchip immutable
pinctrl: apple-gpio: Make the irqchip immutable
gpio: pl061: Make the irqchip immutable
gpio: tegra186: Make the irqchip immutable
gpio: Add helpers to ease the transition towards immutable irq_chip
gpio: Expose the gpiochip_irq_re[ql]res helpers
gpio: Don't fiddle with irqchips marked as immutable
Signed-off-by: Marc Zyngier <maz@kernel.org>
Update the documentation to get rid of the per-gpio_irq_chip
irq_chip structure, and give examples of the new pattern.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220419141846.598305-11-maz@kernel.org
Reformat the whole document, so that automatic numbering and TOC is
properly generated.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411110143.10019-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All of the URLs give 404. There is a little point to preserve them. If
really need be, we could try archive.org if the documents are not there
by a chance.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411110143.10019-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is a tty_driver, not serial -- uart_driver. So move it to the tty
docs dir too. (The same as the driver itself.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411110143.10019-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have n_tty documented in Documentation/driver-api/tty/. n_gsm belongs
there too, so move from serial/ to tty/ too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220411110143.10019-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current documentation for the residue reported in a cyclic transfer
case mentions that the reported residue should be relative to the current
period only. However the definition of DMA_RESIDUE_GRANULARITY_SEGMENT
specifies that the residue should be updated after each period for
a cyclic transfer, which is in direct contradiction.
Moreover the pcm_dmaengine common code uses the residue relative to
the whole cyclic buffer size, not one period.
Correct the residue-related documentation to reflect this.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://lore.kernel.org/r/20220331134114.703782-1-paul.kocialkowski@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Improve ATA queued command allocation as follows:
- For attaining a qc tag for a SAS host we need to allocate a bit in
ata_port.sas_tag_allocated bitmap.
However we already have a unique tag per device in range
[0, ATA_MAX_QUEUE -1] in the scsi cmnd budget token, so just use that
instead.
- It is a bit pointless to have ata_qc_new_init() in libata-core.c since it
pokes scsi internals, so inline it in ata_scsi_qc_new() (in
libata-scsi.c). Also update Doc accordingly.
- Use standard SCSI helpers set_host_byte() and set_status_byte() in
ata_scsi_qc_new().
Christoph Hellwig originally contributed the change to inline
ata_qc_new_init().
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
- Add perf support for nvdimm events, initially only for 'papr_scm'
devices.
- Deprecate the 'block aperture' support in libnvdimm, it only ever
existed in the specification, not in shipping product.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCYjvuTwAKCRDfioYZHlFs
Z4JbAQCViArRj/yxffDB4kg4FNlOgAQbxPblC07E06UX8Jj2DgD+NY2YJIucz0qb
87v0+CorJjtoy5dJ9vxAR8keojT3RQ0=
=oAwm
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The update for this cycle includes the deprecation of block-aperture
mode and a new perf events interface for the papr_scm nvdimm driver.
The perf events approach was acked by PeterZ.
- Add perf support for nvdimm events, initially only for 'papr_scm'
devices.
- Deprecate the 'block aperture' support in libnvdimm, it only ever
existed in the specification, not in shipping product"
* tag 'libnvdimm-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nvdimm/blk: Fix title level
MAINTAINERS: remove section LIBNVDIMM BLK: MMIO-APERTURE DRIVER
powerpc/papr_scm: Fix build failure when
drivers/nvdimm: Fix build failure when CONFIG_PERF_EVENTS is not set
nvdimm/region: Delete nd_blk_region infrastructure
ACPI: NFIT: Remove block aperture support
nvdimm/namespace: Delete nd_namespace_blk
nvdimm/namespace: Delete blk namespace consideration in shared paths
nvdimm/blk: Delete the block-aperture window driver
nvdimm/region: Fix default alignment for small regions
docs: ABI: sysfs-bus-nvdimm: Document sysfs event format entries for nvdimm pmu
powerpc/papr_scm: Add perf interface support
drivers/nvdimm: Add perf interface to expose nvdimm performance stats
drivers/nvdimm: Add nvdimm pmu structure
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
Add a general purpose helper to deep dive into dma_fence_chain/dma_fence_array
structures and iterate over all the fences in them.
This is useful when we need to flatten out all fences in those structures.
v2: some selftests cleanup, improved function naming and documentation
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311110244.1245-1-christian.koenig@amd.com
- Add a driver for 'struct cxl_memdev' objects responsible for CXL.mem
operation as distinct from 'cxl_pci' mailbox operations. Its primary
responsibility is enumerating an endpoint 'struct cxl_port' and all the
'struct cxl_port' instances between an endpoint and the CXL platform
root.
- Add a driver for 'struct cxl_port' objects responsible for enumerating
and operating all Host-managed Device Memory (HDM) decoder resources
between the platform-level CXL memory description, all intervening host
bridges / switches, and the HDM resources in endpoints.
- Update the cxl_pci driver to validate CXL.mem operation precursors to
HDM decoder operation like ready-polling, and legacy CXL 1.1 DVSEC
based CXL.mem configuration.
- Add basic lockdep coverage for usage of device_lock() on CXL subsystem
objects similar to what exists for LIBNVDIMM. Include a compile-time
switch for which subsystem to validate at run-time.
- Update cxl_test to emulate a one level switch topology.
- Document a "Theory of Operation" for the subsystem.
- Add 'numa_node' and 'serial' attributes to cxl_memdev sysfs
- Include miscellaneous fixes for spec / QEMU CXL emulation
compatibility and static analysis reports.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCYjpX6AAKCRDfioYZHlFs
ZzyxAQCztxAXj7mzkm1Qt5zZz4e7p/6sR49B03jBTfPtrEF9kQEAl9R15WVt6U+o
Ooof1XhRic3kT6e8zS3ZVKHzGduYxwM=
=mR94
-----END PGP SIGNATURE-----
Merge tag 'cxl-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull CXL (Compute Express Link) updates from Dan Williams:
"This development cycle extends the subsystem to discover CXL resources
throughout a CXL/PCIe switch topology and respond to hot add/remove
events anywhere in that topology.
This is more foundational infrastructure in preparation for dynamic
memory region provisioning support. Recall that CXL memory regions, as
the new "Theory of Operation" section of
Documentation/driver-api/cxl/memory-devices.rst describes, bring
storage volume striping semantics to memory.
The hot add/remove behavior is validated with extensions to the
cxl_test unit test environment and this test in the cxl-cli test
suite:
https://github.com/pmem/ndctl/blob/djbw/for-74/cxl/test/cxl-topology.sh
Summary:
- Add a driver for 'struct cxl_memdev' objects responsible for
CXL.mem operation as distinct from 'cxl_pci' mailbox operations.
Its primary responsibility is enumerating an endpoint 'struct
cxl_port' and all the 'struct cxl_port' instances between an
endpoint and the CXL platform root.
- Add a driver for 'struct cxl_port' objects responsible for
enumerating and operating all Host-managed Device Memory (HDM)
decoder resources between the platform-level CXL memory
description, all intervening host bridges / switches, and the HDM
resources in endpoints.
- Update the cxl_pci driver to validate CXL.mem operation precursors
to HDM decoder operation like ready-polling, and legacy CXL 1.1
DVSEC based CXL.mem configuration.
- Add basic lockdep coverage for usage of device_lock() on CXL
subsystem objects similar to what exists for LIBNVDIMM. Include a
compile-time switch for which subsystem to validate at run-time.
- Update cxl_test to emulate a one level switch topology.
- Document a "Theory of Operation" for the subsystem.
- Add 'numa_node' and 'serial' attributes to cxl_memdev sysfs
- Include miscellaneous fixes for spec / QEMU CXL emulation
compatibility and static analysis reports"
* tag 'cxl-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl: (48 commits)
cxl/core/port: Fix NULL but dereferenced coccicheck error
cxl/port: Hold port reference until decoder release
cxl/port: Fix endpoint refcount leak
cxl/core: Fix cxl_device_lock() class detection
cxl/core/port: Fix unregister_port() lock assertion
cxl/regs: Fix size of CXL Capability Header Register
cxl/core/port: Handle invalid decoders
cxl/core/port: Fix / relax decoder target enumeration
tools/testing/cxl: Add a physical_node link
tools/testing/cxl: Enumerate mock decoders
tools/testing/cxl: Mock one level of switches
tools/testing/cxl: Fix root port to host bridge assignment
tools/testing/cxl: Mock dvsec_ranges()
cxl/core/port: Add endpoint decoders
cxl/core: Move target_list out of base decoder attributes
cxl/mem: Add the cxl_mem driver
cxl/core/port: Add switch port enumeration
cxl/memdev: Add numa_node attribute
cxl/pci: Emit device serial number
cxl/pci: Implement wait for media active
...
dma-buf:
- rename dma-buf-map to iosys-map
core:
- move buddy allocator to core
- add pci/platform init macros
- improve EDID parser deep color handling
- EDID timing type 7 support
- add GPD Win Max quirk
- add yes/no helpers to string_helpers
- flatten syncobj chains
- add nomodeset support to lots of drivers
- improve fb-helper clipping support
- add default property value interface
fbdev:
- improve fbdev ops speed
ttm:
- add a backpointer from ttm bo->ttm resource
dp:
- move displayport headers
- add a dp helper module
bridge:
- anx7625 atomic support, HDCP support
panel:
- split out panel-lvds and lvds bindings
- find panels in OF subnodes
privacy:
- add chromeos privacy screen support
fb:
- hot unplug fw fb on forced removal
simpledrm:
- request region instead of marking ioresource busy
- add panel oreintation property
udmabuf:
- fix oops with 0 pages
amdgpu:
- power management code cleanup
- Enable freesync video mode by default
- RAS code cleanup
- Improve VRAM access for debug using SDMA
- SR-IOV rework special register access and fixes
- profiling power state request ioctl
- expose IP discovery via sysfs
- Cyan skillfish updates
- GC 10.3.7, SDMA 5.2.7, DCN 3.1.6 updates
- expose benchmark tests via debugfs
- add module param to disable XGMI for testing
- GPU reset debugfs register dumping support
amdkfd:
- CRIU support
- SDMA queue fixes
radeon:
- UVD suspend fix
- iMac backlight fix
i915:
- minimal parallel submission for execlists
- DG2-G12 subplatform added
- DG2 programming workarounds
- DG2 accelerated migration support
- flat CCS and CCS engine support for XeHP
- initial small BAR support
- drop fake LMEM support
- ADL-N PCH support
- bigjoiner updates
- introduce VMA resources and async unbinding
- register definitions cleanups
- multi-FBC refactoring
- DG1 OPROM over SPI support
- ADL-N platform enabling
- opregion mailbox #5 support
- DP MST ESI improvements
- drm device based logging
- async flip optimisation for DG2
- CPU arch abstraction fixes
- improve GuC ADS init to work on aarch64
- tweak TTM LRU priority hint
- GuC 69.0.3 support
- remove short term execbuf pins
nouveau:
- higher DP/eDP bitrates
- backlight fixes
msm:
- dpu + dp support for sc8180x
- dp support for sm8350
- dpu + dsi support for qcm2290
- 10nm dsi phy tuning support
- bridge support for dp encoder
- gpu support for additional 7c3 SKUs
ingenic:
- HDMI support for JZ4780
- aux channel EDID support
ast:
- AST2600 support
- add wide screen support
- create DP/DVI connectors
omapdrm:
- fix implicit dma_buf fencing
vc4:
- add CSC + full range support
- better display firmware handoff
panfrost:
- add initial dual-core GPU support
stm:
- new revision support
- fb handover support
mediatek:
- transfer display binding document to yaml format.
- add mt8195 display device binding.
- allow commands to be sent during video mode.
- add wait_for_event for crtc disable by cmdq.
tegra:
- YUV format support
rcar-du:
- LVDS support for M3-W+ (R8A77961)
exynos:
- BGR pixel format for FIMD device
-----BEGIN PGP SIGNATURE-----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=uRsT
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2022-03-24' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Lots of work all over, Intel improving DG2 support, amdkfd CRIU
support, msm new hw support, and faster fbdev support.
dma-buf:
- rename dma-buf-map to iosys-map
core:
- move buddy allocator to core
- add pci/platform init macros
- improve EDID parser deep color handling
- EDID timing type 7 support
- add GPD Win Max quirk
- add yes/no helpers to string_helpers
- flatten syncobj chains
- add nomodeset support to lots of drivers
- improve fb-helper clipping support
- add default property value interface
fbdev:
- improve fbdev ops speed
ttm:
- add a backpointer from ttm bo->ttm resource
dp:
- move displayport headers
- add a dp helper module
bridge:
- anx7625 atomic support, HDCP support
panel:
- split out panel-lvds and lvds bindings
- find panels in OF subnodes
privacy:
- add chromeos privacy screen support
fb:
- hot unplug fw fb on forced removal
simpledrm:
- request region instead of marking ioresource busy
- add panel oreintation property
udmabuf:
- fix oops with 0 pages
amdgpu:
- power management code cleanup
- Enable freesync video mode by default
- RAS code cleanup
- Improve VRAM access for debug using SDMA
- SR-IOV rework special register access and fixes
- profiling power state request ioctl
- expose IP discovery via sysfs
- Cyan skillfish updates
- GC 10.3.7, SDMA 5.2.7, DCN 3.1.6 updates
- expose benchmark tests via debugfs
- add module param to disable XGMI for testing
- GPU reset debugfs register dumping support
amdkfd:
- CRIU support
- SDMA queue fixes
radeon:
- UVD suspend fix
- iMac backlight fix
i915:
- minimal parallel submission for execlists
- DG2-G12 subplatform added
- DG2 programming workarounds
- DG2 accelerated migration support
- flat CCS and CCS engine support for XeHP
- initial small BAR support
- drop fake LMEM support
- ADL-N PCH support
- bigjoiner updates
- introduce VMA resources and async unbinding
- register definitions cleanups
- multi-FBC refactoring
- DG1 OPROM over SPI support
- ADL-N platform enabling
- opregion mailbox #5 support
- DP MST ESI improvements
- drm device based logging
- async flip optimisation for DG2
- CPU arch abstraction fixes
- improve GuC ADS init to work on aarch64
- tweak TTM LRU priority hint
- GuC 69.0.3 support
- remove short term execbuf pins
nouveau:
- higher DP/eDP bitrates
- backlight fixes
msm:
- dpu + dp support for sc8180x
- dp support for sm8350
- dpu + dsi support for qcm2290
- 10nm dsi phy tuning support
- bridge support for dp encoder
- gpu support for additional 7c3 SKUs
ingenic:
- HDMI support for JZ4780
- aux channel EDID support
ast:
- AST2600 support
- add wide screen support
- create DP/DVI connectors
omapdrm:
- fix implicit dma_buf fencing
vc4:
- add CSC + full range support
- better display firmware handoff
panfrost:
- add initial dual-core GPU support
stm:
- new revision support
- fb handover support
mediatek:
- transfer display binding document to yaml format.
- add mt8195 display device binding.
- allow commands to be sent during video mode.
- add wait_for_event for crtc disable by cmdq.
tegra:
- YUV format support
rcar-du:
- LVDS support for M3-W+ (R8A77961)
exynos:
- BGR pixel format for FIMD device"
* tag 'drm-next-2022-03-24' of git://anongit.freedesktop.org/drm/drm: (1529 commits)
drm/i915/display: Do not re-enable PSR after it was marked as not reliable
drm/i915/display: Fix HPD short pulse handling for eDP
drm/amdgpu: Use drm_mode_copy()
drm/radeon: Use drm_mode_copy()
drm/amdgpu: Use ternary operator in `vcn_v1_0_start()`
drm/amdgpu: Remove pointless on stack mode copies
drm/amd/pm: fix indenting in __smu_cmn_reg_print_error()
drm/amdgpu/dc: fix typos in comments
drm/amdgpu: fix typos in comments
drm/amd/pm: fix typos in comments
drm/amdgpu: Add stolen reserved memory for MI25 SRIOV.
drm/amdgpu: Merge get_reserved_allocation to get_vbios_allocations.
drm/amdkfd: evict svm bo worker handle error
drm/amdgpu/vcn: fix vcn ring test failure in igt reload test
drm/amdgpu: only allow secure submission on rings which support that
drm/amdgpu: fixed the warnings reported by kernel test robot
drm/amd/display: 3.2.177
drm/amd/display: [FW Promotion] Release 0.0.108.0
drm/amd/display: Add save/restore PANEL_PWRSEQ_REF_DIV2
drm/amd/display: Wait for hubp read line for Pollock
...
- Introduce new device migration uAPI and implement device specific
mlx5 vfio-pci variant driver supporting new protocol (Jason Gunthorpe,
Yishai Hadas, Leon Romanovsky)
- New HiSilicon acc vfio-pci variant driver, also supporting migration
interface (Shameer Kolothum, Longfang Liu)
- D3hot fixes for vfio-pci-core (Abhishek Sahu)
- Document new vfio-pci variant driver acceptance criteria
(Alex Williamson)
- Fix UML build unresolved ioport_{un}map() functions
(Alex Williamson)
- Fix MAINTAINERS due to header movement (Lukas Bulwahn)
-----BEGIN PGP SIGNATURE-----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=Sv96
-----END PGP SIGNATURE-----
Merge tag 'vfio-v5.18-rc1' of https://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- Introduce new device migration uAPI and implement device specific
mlx5 vfio-pci variant driver supporting new protocol (Jason
Gunthorpe, Yishai Hadas, Leon Romanovsky)
- New HiSilicon acc vfio-pci variant driver, also supporting migration
interface (Shameer Kolothum, Longfang Liu)
- D3hot fixes for vfio-pci-core (Abhishek Sahu)
- Document new vfio-pci variant driver acceptance criteria
(Alex Williamson)
- Fix UML build unresolved ioport_{un}map() functions
(Alex Williamson)
- Fix MAINTAINERS due to header movement (Lukas Bulwahn)
* tag 'vfio-v5.18-rc1' of https://github.com/awilliam/linux-vfio: (31 commits)
vfio-pci: Provide reviewers and acceptance criteria for variant drivers
MAINTAINERS: adjust entry for header movement in hisilicon qm driver
hisi_acc_vfio_pci: Use its own PCI reset_done error handler
hisi_acc_vfio_pci: Add support for VFIO live migration
crypto: hisilicon/qm: Set the VF QM state register
hisi_acc_vfio_pci: Add helper to retrieve the struct pci_driver
hisi_acc_vfio_pci: Restrict access to VF dev BAR2 migration region
hisi_acc_vfio_pci: add new vfio_pci driver for HiSilicon ACC devices
hisi_acc_qm: Move VF PCI device IDs to common header
crypto: hisilicon/qm: Move few definitions to common header
crypto: hisilicon/qm: Move the QM header to include/linux
vfio/mlx5: Fix to not use 0 as NULL pointer
PCI/IOV: Fix wrong kernel-doc identifier
vfio/mlx5: Use its own PCI reset_done error handler
vfio/pci: Expose vfio_pci_core_aer_err_detected()
vfio/mlx5: Implement vfio_pci driver for mlx5 devices
vfio/mlx5: Expose migration commands over mlx5 device
vfio: Remove migration protocol v1 documentation
vfio: Extend the device migration protocol with RUNNING_P2P
vfio: Define device migration protocol v2
...
Dave Airlie