Fixes the following sparse warning:
drivers/gpio/gpio-pca953x.c:292:28: warning:
symbol 'pca953x_i2c_regmap' was not declared. Should it be static?
Fixes: 4942723276 ("gpio: pca953x: Perform basic regmap conversion")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
acpi_gpiochip_alloc_event only continues allocating an event and adding
it to the list if gpiochip_request_own_desc does not return an error.
So events with an error desc are never placed on the events list and this
check is really not necessary.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Some core changes are already in outside of this pull
request as they came through the regulator tree, most
notably devm_gpiod_unhinge() that removes devres refcount
management from a GPIO descriptor. This is needed in
subsystems such as regulators where the regulator core
need to take over the reference counting and lifecycle
management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match()
as nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This
helps setting the direction now that we are two GPIO
maintainers.
- Handle the MMC CD/WP properties in the device tree core.
(The bulk of patches activating this code is already
merged through the MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so
we as gpiochips can request lines as active low or open
drain etc even from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has
been around for ages, and is now modernized to reduce code
duplication that has stacked up and is using regmap to read
write and cache registers.
- Intel drivers are now maintained in a separate tree and
start with a round of cleanups and unifications.
-----BEGIN PGP SIGNATURE-----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=05LW
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.21 kernel series.
Core changes:
- Some core changes are already in outside of this pull request as
they came through the regulator tree, most notably
devm_gpiod_unhinge() that removes devres refcount management from a
GPIO descriptor. This is needed in subsystems such as regulators
where the regulator core need to take over the reference counting
and lifecycle management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This helps
setting the direction now that we are two GPIO maintainers.
- Handle the MMC CD/WP properties in the device tree core. (The bulk
of patches activating this code is already merged through the
MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so we as
gpiochips can request lines as active low or open drain etc even
from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has been
around for ages, and is now modernized to reduce code duplication
that has stacked up and is using regmap to read write and cache
registers.
- Intel drivers are now maintained in a separate tree and start with
a round of cleanups and unifications"
* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
gpio: sama5d2-piobu: Depend on OF_GPIO
gpio: Add Cadence GPIO driver
dt-bindings: gpio: Add bindings for Cadence GPIO
gpiolib-acpi: remove unused variable 'err', cleans up build warning
gpio: mxs: read pin level directly instead of using .get
gpio: aspeed: remove duplicated statement
gpio: add driver for SAMA5D2 PIOBU pins
dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
gpio/mmc/of: Respect polarity in the device tree
dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
memory: omap-gpmc: Get the header of the enum
ARM: omap1: Fix new user of gpiochip_request_own_desc()
gpio: pca953x: Add regmap dependency for PCA953x driver
gpio: raspberrypi-exp: decrease refcount on firmware dt node
gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
gpio: pca953x: Restore registers after suspend/resume cycle
gpio: pca953x: Zap single use of pca953x_read_single()
gpio: pca953x: Zap ad-hoc reg_output cache
gpio: pca953x: Zap ad-hoc reg_direction cache
gpio: pca953x: Perform basic regmap conversion
...
- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver
-----BEGIN PGP SIGNATURE-----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=mB5P
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"This time, this pull request contains changes crossing subsystems and
archs/platforms, which is mainly because of a bigger modernization of
moving from legacy GPIO to GPIO descriptors for MMC (by Linus
Walleij).
Additionally, once again, I am funneling changes to
drivers/misc/cardreader/* and drivers/memstick/* through my MMC tree,
mostly due to that we lack a maintainer for these.
Summary:
MMC core:
- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver"
* tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (99 commits)
mmc: mediatek: Add MMC_CAP_SDIO_IRQ support
mmc: renesas_sdhi_internal_dmac: Whitelist r8a774c0
dt-bindings: mmc: renesas_sdhi: Add r8a774c0 support
mmc: core: Cleanup BKOPS support
mmc: core: Drop redundant check in mmc_send_hpi_cmd()
mmc: sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures (i929)
dt-bindings: sdhci-omap: Add note for cpu_thermal
mmc: sdhci-acpi: Disable LED control for Intel BYT-based controllers
mmc: sdhci-pci: Disable LED control for Intel BYT-based controllers
mmc: sdhci: Add quirk to disable LED control
mmc: mmci: add variant property to set command stop bit
misc: alcor_pci: fix spelling mistake "invailid" -> "invalid"
mmc: meson-gx: add signal resampling
mmc: meson-gx: align default phase on soc vendor tree
mmc: meson-gx: remove useless lock
mmc: meson-gx: make sure the descriptor is stopped on errors
mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver
dt-bindings: mmc: sdhci-of-arasan: Add deprecated message for AM65
dt-bindings: mmc: sdhci-am654: Document bindings for the host controllers on TI's AM654 SOCs
mmc: sdhci-msm: avoid unused function warning
...
This has been a busy release for the regmap-irq code, there's several
new features been added, including an API cleanup for how we specify
types that affected one existing driver (gpio-max77620):
- Support for hardware that flags rising and falling edges on separate
status bits from Bartosz Golaszewski.
- Support for explicitly clearing interrupts before unmasking from
Bartosz Golaszewski.
- Support for level triggered IRQs from Matti Vaittinen.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwhMAUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MI0B/9K27CbnGskQHZqWQxcFg1iVck/ZPty
kqfIGYDafvqT2TaVL+tFM8kzjLB3dMuV3cbywppq6+pzEvR/BDzhUKbskNPSLjUo
zNxKbwiBJPFLqlZORhzncuPcpRvrGGp120B+gr7lKOJgSG73u6bvOEzYaZbJzPb8
KiKo5oFqB/wpj3Gw243RjYE+7yaM/i7IAR/mW//RoKMWYERv6koR+GL0jgalib4d
mezH0ipO/SGDPorVOeUWxm/mlUYhEbitTa9+BtAYC/0+Nba1ns1p6dduchhXrAA0
/cOCHHVypPSiKLxjth+FA20CbemALb6swoZztVWYNS+0jJ2/bkh1rCoB
=aiDq
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a busy release for the regmap-irq code, there's several
new features been added, including an API cleanup for how we specify
types that affected one existing driver (gpio-max77620):
- Support for hardware that flags rising and falling edges on
separate status bits from Bartosz Golaszewski.
- Support for explicitly clearing interrupts before unmasking from
Bartosz Golaszewski.
- Support for level triggered IRQs from Matti Vaittinen"
* tag 'regmap-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: irq: add an option to clear status registers on unmask
regmap: regmap-irq/gpio-max77620: add level-irq support
regmap: regmap-irq: Remove default irq type setting from core
regmap: debugfs: convert to DEFINE_SHOW_ATTRIBUTE
regmap: rbtree: convert to DEFINE_SHOW_ATTRIBUTE
regmap: irq: handle HW using separate rising/falling edge interrupts
regmap: add a new macro:REGMAP_IRQ_REG_LINE(_id, _reg_bits)
This has been a very busy release for the core, some fixes, one large new
feature and a big bit of refactoring to update the GPIO API:
- Support for coupled regulators from Dmitry Osipenko based on a prior
attempt by Maciej Purski, allowing us to handle situations where the
voltages on two regulators can't be too far apart from each other.
- Conversion of the GPIO support in both drivers and the core to use
GPIO descriptors rather than numbers, part of the overall project to
remove GPIO numbers.
- Support for standby mode suspend states from Andrei Stefanescu.
- New drivers for Allwinner AXP209, Cirrus Logic Lochnagar and
Microchip MPC16502.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwhKkcTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DFfB/91/ECmybKTP+RvwUTZ0rrqFFs2C9Vl
76vH242exyJuzv44inWi9gOcXFDn7c9hf7Vl4Jd5UVP53Nzm5I8ZwExQsxax9BsN
hltlX01UpRAmHNkMNrnJH6YAntD3EicYGSUDjohkWItIDqpMAjhWpx/yGXTEjBir
gvkV51bF3qAYQe0g6MmK3KeVw96QPNjUhoPbsqbpaXaF6fmyOVzMiFrffJGmUAyM
J5qRv3OhsZiZy2/zxNLkUI6y4XKDEaFJ3RhSKoUwItGyKQt2saXMoJGyEEWm2b6X
coTm0ZQk+EU+b659lDHErTM4YUx7p7tQt3VM09NoMD8B261TdZ0y99Oh
=8Rxt
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been a very busy release for the core, some fixes, one large
new feature and a big bit of refactoring to update the GPIO API:
- Support for coupled regulators from Dmitry Osipenko based on a
prior attempt by Maciej Purski, allowing us to handle situations
where the voltages on two regulators can't be too far apart from
each other.
- Conversion of the GPIO support in both drivers and the core to use
GPIO descriptors rather than numbers, part of the overall project
to remove GPIO numbers.
- Support for standby mode suspend states from Andrei Stefanescu.
- New drivers for Allwinner AXP209, Cirrus Logic Lochnagar and
Microchip MPC16502"
* tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (90 commits)
regulator: tps65910: fix a missing check of return value
regulator: mcp16502: Select REGMAP_I2C to fix build error
regulator: convert to DEFINE_SHOW_ATTRIBUTE
regulator: mcp16502: Fix missing n_voltages setting
regulator: mcp16502: Use #ifdef CONFIG_PM_SLEEP around mcp16502_suspend/resume_noirq
regulator: mcp16502: code cleanup
regulator: act8945a-regulator: make symbol act8945a_pm static
drivers/regulator: fix a missing check of return value
regulator: act8945a-regulator: fix 'defined but not used' compiler warning
regulator: axp20x: fix set_ramp_delay for AXP209/dcdc2
regulator: mcp16502: add support for suspend
mfd: axp20x: use explicit bit defines
mfd: axp20x: Clean up included headers
regulator: dts: enable soft-start and ramp delay for the OLinuXino Lime2
dt-bindings: mfd: axp20x: Add software based soft_start for AXP209 LDO3
regulator: axp20x: add software based soft_start for AXP209 LDO3
dt-bindings: mfd: axp20x: add support for regulator-ramp-delay for AXP209
regulator: axp20x: add support for set_ramp_delay for AXP209
mfd: axp20x: name voltage ramping define properly
regulator: mcp16502: add regulator driver for MCP16502
...
This driver clearly needs OF_GPIO so depend on it.
Fixes a build error.
Cc: Andrei Stefanescu <Andrei.Stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- ACPI IRQ request deferral
- OMAP: revert deferred wakeup quirk
- MAX7301: fix DMA safe memory handling
- MVEBU: selective probe failure on missing clk
-----BEGIN PGP SIGNATURE-----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=+Iw2
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Hopefully last round of GPIO fixes.
The ACPI patch is pretty important for some laptop users, the rest is
driver-specific for embedded (mostly ARM) systems.
I took out one ACPI patch that wasn't critical enough because I
couldn't justify sending it at this point, and that is why the commit
date is today, but the patches have been in linux-next.
Sorry for not sending some of them earlier :(
Notice that we have a co-maintainer for GPIO now, Bartosz Golaszewski,
and he might jump in and make some pull requests at times when I am
off.
Summary:
- ACPI IRQ request deferral
- OMAP: revert deferred wakeup quirk
- MAX7301: fix DMA safe memory handling
- MVEBU: selective probe failure on missing clk"
* tag 'gpio-v4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mvebu: only fail on missing clk if pwm is actually to be used
gpio: max7301: fix driver for use with CONFIG_VMAP_STACK
gpio: gpio-omap: Revert deferred wakeup quirk handling for regressions
gpiolib-acpi: Only defer request_irq for GpioInt ACPI event handlers
This patch adds a driver for Cadence GPIO controller.
It can be enabled with GPIO_CADENCE Kconfig option.
It uses generic GPIO infrastructure and works
as an interrupt controller.
At the moment it only supports level sensitive irqs.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Variable err is defined but never used. Remove it. Cleans up warning:
warning: unused variable ‘err’ [-Wunused-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Calling readl directly instead of going through another function that
results in the same result to remove some overhead. I didn't try to
measure the performance gain, but IMHO there is little benefit from
abstracting a GPIO register access in the GPIO driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove duplicated assignment statement from aspeed_gpio_probe() function.
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PIOBU pins do not lose their voltage during Backup/Self-refresh.
This patch adds a simple GPIO controller for them and a
maintainer for the driver.
This driver adds support for using the pins as GPIO
offering the possibility to read/set the voltage.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio IP on Armada 370 at offset 0x18180 has neither a clk nor pwm
registers. So there is no need for a clk as the pwm isn't used anyhow.
So only check for the clk in the presence of the pwm registers. This fixes
a failure to probe the gpio driver for the above mentioned gpio device.
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
spi_read() and spi_write() require DMA-safe memory. When
CONFIG_VMAP_STACK is selected, those functions cannot be used
with buffers on stack.
This patch replaces calls to spi_read() and spi_write() by
spi_write_then_read() which doesn't require DMA-safe buffers.
Fixes: 0c36ec3147 ("gpio: gpio driver for max7301 SPI GPIO expander")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit ec0daae685 ("gpio: omap: Add level wakeup handling for omap4
based SoCs") attempted to fix omap4 GPIO wakeup handling as it was
blocking deeper SoC idle states. However this caused a regression for
GPIOs during runtime having over second long latencies for Ethernet
GPIO interrupt as reportedy by Russell King <rmk+kernel@armlinux.org.uk>.
Let's fix this issue by doing a partial revert of the breaking commit.
We still want to keep the quirk handling around as it is also used for
OMAP_GPIO_QUIRK_IDLE_REMOVE_TRIGGER.
The real fix for omap4 GPIO wakeup handling involves fixes for
omap_set_gpio_trigger() and omap_gpio_unmask_irq() and will be posted
separately. And we must keep the wakeup bit enabled during runtime
because of module doing clock autogating with autoidle configured.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Fixes: ec0daae685 ("gpio: omap: Add level wakeup handling for omap4
based SoCs")
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add level active IRQ support to regmap-irq irqchip. Change breaks
existing regmap-irq type setting. Convert the existing drivers which
use regmap-irq with trigger type setting (gpio-max77620) to work
with this new approach. So we do not magically support level-active
IRQs on gpio-max77620 - but add support to the regmap-irq for chips
which support them =)
We do not support distinguishing situation where HW supports rising
and falling edge detection but not both. Separating this would require
inventing yet another flags for IRQ types.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device tree bindings for the MMC card detect and
write protect lines specify that these should be active
low unless "cd-inverted" or "wp-inverted" has been
specified.
However that is not how the kernel code has worked. It
has always respected the flags passed to the phandle in
the device tree, but respected the "cd-inverted" and
"wp-inverted" flags such that if those are set, the
polarity will be the inverse of that specified in the
device tree.
Switch to behaving like the old code did and fix the
regression.
Fixes: 81c85ec15a ("gpio: OF: Parse MMC-specific CD and WP properties")
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Select REGMAP_I2C in Kconfig, since the driver now depends on regmap
and this was missing, thus breaking build on various systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We're getting a reference RPi's firmware node in order to be able to
communicate with it's driver. We should decrease the reference count on
the dt node after being done with it.
Fixes: a98d90e7d5 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO expander via mailbox service")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using the name directly from the I2C client
to name the gpio_chip, use dev_name() on the client->dev,
so we get the sometimes more unique device name, as I2C has
a mechanism for naming its devices explicitly in e.g.
board data.
This is a prerequisite for being able to reference
uniquely any I2C GPIO expander defined in a board file
when setting up GPIO descriptor tables.
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is possible that the PCA953x is powered down during suspend.
Use regmap cache to assure the registers in the PCA953x are in
line with the driver state after resume.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop pca953x_write_single() which is used in one place.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the ad-hoc reg_output output register caching with generic
regcache cache. Drop pca953x_write_single() which is no longer used.
This reduces code duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the driver to use regmap to access the chips. Due to the convoluted
register mapping scheme, implement read/write/volatile check functions that
untangle the mess and perform check accordingly. This patch does not zap the
internal register cache of the PCA953x driver, nor does it push the regmap
access down into the gpiochip accessors to simplify the review. All that is
in subsequent patches.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of having the I2C register calculation function spread across
multiple accessor functions, pull it out into a single function which
returns the adjusted register address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ad-hoc i2c block write can be replaced by standard register accessor
function, which correctly handles all the chip details and differences.
Do so to simplify the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCA957x and PCA953x init functions are almost the same, except for
the different register mapping and one extra write to BKEN register in
case of PCA957x. Factor out the common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At this point, the pca953x_{read,write}_regs_mul() can read single bank
PCA953x GPIO chips as well. Merge the _8 and _mul functions together to
simplify the code a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At this point, these two functions only differ in whether they do or do not
set the address increment bit. The 16 GPIO case does not need to set the AI
bit, except for PCA9575 on write, while the 24 GPIO and more case does set
the AI bit always. Merge these two functions together to simplify the code
a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At this point, these two functions only differ in whether they do or do not
set the address increment bit on PCA9575. Merge these two functions together
to simplify the code a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The multi-byte IO on various pca953x chips requires the auto-increment bit,
while other chips toggle the LSbit automatically. Note that LSbit toggling
only alternates between two registers during the IO, it is not the same as
address auto-increment. The driver currently assumes that #gpios > 16 implies
auto-increment, while #gpios <= 16 implies LSbit toggling. This is incorrect
at there are chips with 16 GPIOs which require the auto-increment bit.
The PCA9575, according to NXP datasheet rev. 4.2 from 16 April 2015, section
7.3 Command Register, the bit 7 in command register is the auto-increment
bit, which allows programming multiple registers sequentially.
Set this bit both in pca953x_gpio_set_multiple(), where it fixes the multi
register programming, and in pca957x_write_regs_16(), where is simplifies
the function. In fact, the pca957x_write_regs_16() now looks rather similar
to pca953x_write_regs_24() and pca953x_write_regs_16(), which is intended
for subsequent patches.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCAL_PINCTRL_MASK is too large. The extended register block on
PCAL6524, which is the largest chip with this block, has the block
limited to address range 0x40..0x7f. This is because the bit 7 in
the command register is used for the Address Increment functionality.
Trim the mask to 0x60 to match the datasheet and to prevent accidental
overwrite of the AI bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bank_shift = fls(...) code was duplicated in the driver 5 times,
pull it into separate function.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IRQ core code refers to the interrupt type by that name, whereas the
term flow is almost never used. Some GPIO controllers use the term
flow_type, but it is most consistent to just go with the IRQ core
terminology.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use managed resource allocation in pch and sodaville drivers.
Switch to use for_each_set_bit() in IRQ handlers.
Headers clean up.
Sort headers in inclusion block alphabetically for better maintenance.
Convert to SPDX identifier and fixing MODULE_LICENSE() when appropriate.
Additional format fixes to rectify debug and message printing.
There is a commit which had been applied to v4.20-rc4, that's why dup.
- c3bc3ff9e8 MAINTAINERS: Do maintain Intel GPIO drivers via separate tree
The following is an automated git shortlog grouped by driver:
ich:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Join string literals back
- Convert pr_<level> to dev_<level>
- Switch to use struct device instead of platform_device
- Simplify error handling in ichx_write_bit()
intel-mid:
- Convert to use SPDX identifier
- Remove linux/module.h and sort headers
lynxpoint:
- Convert to use SPDX identifier
- Remove linux/init.h and sort headers
- Use for_each_set_bit() in IRQ handler
MAINTAINERS:
- Do maintain Intel GPIO drivers via separate tree
merrifield:
- Convert to use SPDX identifier
- Remove linux/init.h
pch:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Remove duplicate assignments
- Remove redundant __func__ from debug print
- Use for_each_set_bit() in IRQ handler
- Convert to dev_pm_ops
- Convert to use managed functions pcim_* and devm_*
sch:
- Convert to use SPDX identifier
- Remove linux/init.h and sort headers
sodaville:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Use for_each_set_bit() in IRQ handler
- Convert to use managed functions pcim_* and devm_*
-----BEGIN PGP SIGNATURE-----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=5W0M
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v4.21-1
Use managed resource allocation in pch and sodaville drivers.
Switch to use for_each_set_bit() in IRQ handlers.
Headers clean up.
Sort headers in inclusion block alphabetically for better maintenance.
Convert to SPDX identifier and fixing MODULE_LICENSE() when appropriate.
Additional format fixes to rectify debug and message printing.
There is a commit which had been applied to v4.20-rc4, that's why dup.
- c3bc3ff9e8 MAINTAINERS: Do maintain Intel GPIO drivers via separate tree
The following is an automated git shortlog grouped by driver:
ich:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Join string literals back
- Convert pr_<level> to dev_<level>
- Switch to use struct device instead of platform_device
- Simplify error handling in ichx_write_bit()
intel-mid:
- Convert to use SPDX identifier
- Remove linux/module.h and sort headers
lynxpoint:
- Convert to use SPDX identifier
- Remove linux/init.h and sort headers
- Use for_each_set_bit() in IRQ handler
MAINTAINERS:
- Do maintain Intel GPIO drivers via separate tree
merrifield:
- Convert to use SPDX identifier
- Remove linux/init.h
pch:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Remove duplicate assignments
- Remove redundant __func__ from debug print
- Use for_each_set_bit() in IRQ handler
- Convert to dev_pm_ops
- Convert to use managed functions pcim_* and devm_*
sch:
- Convert to use SPDX identifier
- Remove linux/init.h and sort headers
sodaville:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Use for_each_set_bit() in IRQ handler
- Convert to use managed functions pcim_* and devm_*
Before things go out of hand, make it possible to pass
flags when requesting "own" descriptors from a gpio_chip.
This is necessary if the chip wants to request a GPIO with
active low semantics, for example.
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a function named devm_gpiod_unhinge() that removes
the resource management from a GPIO descriptor.
I am not sure if this is the best anglosaxon name for the
function, no other managed resources have an equivalent
currently, but I chose "unhinge" as the closest intuitive
thing I could imagine that fits Rusty Russell's API design
criterions "the obvious use is the correct one" and
"the name tells you how to use it".
The idea came out of a remark from Mark Brown that it should
be possible to handle over management of a resource from
devres to the regulator core, and indeed we can do that.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we get a nonexeclusive GPIO descriptor using managed
resources, we should only add it to the list of managed
resources once: on the first user. Augment the
devm_gpiod_get_index() and devm_gpiod_get_from_of_node()
calls to account for this by checking if the descriptor
is already resource managed before we proceed to allocate
a new resource management struct.
Fixes: b0ce7b29bf ("regulator/gpio: Allow nonexclusive GPIO access")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes gpiod_get_from_of_node() respect the
GPIOD_FLAGS_BIT_NONEXCLUSIVE flag which is especially
nice when getting regulator GPIOs right out of device
tree nodes.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: b0ce7b29bf ("regulator/gpio: Allow nonexclusive GPIO access")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function already exist inside gpiolib, we were just
reluctant to make it available to the kernel at large as
the devm_* seemed to be enough for anyone.
However we found out that regulators need to do their own
lifecycle/refcounting on GPIO descriptors and explicitly
call gpiod_put() when done with a descriptor, so export
this function so we can hand the refcounting over to the
regulator core for these descriptors after retrieveal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The problem is reported for allmodconfig build setup:
ERROR: "irq_chip_retrigger_hierarchy" [drivers/gpio/gpio-lpc18xx.ko] undefined!
make[2]: *** [scripts/Makefile.modpost:92: __modpost] Error 1
make[1]: *** [Makefile:1271: modules] Error 2
My testing in runtime shows that it is sufficient to remove .irq_retrigger
callback, which is assigned to unexported irq_chip_retrigger_hierarchy()
function, I did't observe any regressions, and thus apparently it is a
better fix rather than exporting the function defined in kernel/irq/chip.c
(see commit 52b2a05fa7 ("genirq: Export IRQ functions for module use"))
or sticking the GPIO controller driver build to built-in option only.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 5ddabfe8d3 ("gpio: lpc18xx: add GPIO pin interrupt controller support")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Wei Yongjun