Check successful completion of BSM loading. Give a chance to
load BSM again. If BSM loading is unsuccessful we should exit
and not initilize NIC. Before this checking even if the BSM loading failed
driver tries to initilize the NIC which should not be the case.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
4965 hardware has 7 queues reserved and the
remaining ones used for aggregation, 5000
and higher need to have 10 reserved. This
is not very clear in the code right now,
unfortunately.
Introduce a new IWL_TX_FIFO_UNUSED constant
and make the queue/FIFO mapping arrays able
to hold that value, and change the setup
code to reserve all queues in the arrays
(the queue number is the index) and use the
new unused constant to not map those queues
to any FIFO.
Additionally, clear up the AC/queue mapping
code to be more understandable. The mapping
is the identity mapping right now, but with
the mapping function I think it's easier to
understand what happens there.
Finally, HCCA isn't implemented at all and
I think newer microcode removed it, so let's
remove all mention of it in the code, some
comments remain for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Add internal short scan support for 3945 NIC, This allows 3945 NIC
to support radio reset request like the other series of NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
small change to remove unnecessary "ret" parameter since it not being
used.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
"internal_scan" debugfs function serves the same propose of mode "0" of
"force_reset" debugfs function. Remove it to avoid duplicate.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_apm_stop_master and iwl_internal_short_hw_scan
are only used within iwlcore and thus do not need to be exported.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For later station notification support we would like WEP key setting to be
done synchronously always. Currently all places from which WEP key is set
can sleep, but the usage of sta_lock prevents it to do so. Modify the
locking to use priv->mutex instead and thus enable this call to sleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
small code cleanup to remove un-necessary parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
These files are incompatible with some changes
I'm making, and don't really belong into sysfs
anyway as they can only be used for debugging.
Since writing them will probably crash the
firmware, keep only the reading part and move
them into debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since rfkill integration, mac80211 can no
longer add an interface while the hardware
is not ready, so STATUS_MODE_PENDING can
never be set.
Also, remove another superfluous channel
sanity check and return the commit_rxon
return value in case it failed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This code will never trigger, because when
we call this during interface start, neither
priv->vif nor priv->iw_mode conditions will
be true, and when it happens during reset
then priv->vif is also NULL. Also, in both
cases the same code will be executed as part
of iwl_bss_info_changed(), which contains a
copy of this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Only used on 3945, so it can be in the
3945-specific part of the data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Not all queues are mapped for frame transmission,
so saying "AC" is misleading. They are all mapped
to FIFOs, obviously, though, so use that term and
also say AC/CMD instead of just AC for the queue
type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_mac_beacon_update can only be called
when the operating mode is IBSS, so it
doesn't need to verify that again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 will always enforce using a channel
that the driver allowed for IBSS use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This variable is assigned a default value,
but then assigned zero as soon as mac80211
calls a change channel (which will happen
right after the hw is started) and after
that it never changes again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
With some of the new code in mac80211, public action
frames can be exchanged as non-injected frames even
while not associated.
Aside from that, dropping frames here is pointless
since we do deal with arbitrary frames that were
injected already, so let mac80211 make the decision
about which frames to allow or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_mac_reset_tsf will only ever be called in
IBSS mode, so checking for other modes is not
useful and the code that depends on that will
not be executed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 will not allow using channels not
marked as allowing IBSS for IBSS mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Updating the variables last_rx_rssi, last_tsf
and last_beacon_time needs a lot of code but
they are not actually used in iwlagn (only in
3945) so we can move them to the 3945 specific
data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Since the ICT data is all AGN specific, it can
be the first data to create the _agn part of the
device-specific union in the priv struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
To be obviously correct, this patch only modifies
3945 files and the struct definition. A follow-up
patch will create the AGN part of the union.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
All the ICT ISR code is iwlagn specific, and doesn't
need to be in iwlcore. So create a new iwl-agn.h
header file that will hold agn specific function
declarations etc., and move the ICT code into a new
iwl-agn-ict.c file that is linked into iwlagn. This
also gets rid of exporting those symbols.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The AR_IMR_S2 register sometimes cannot be read correctly. Instead of a
valid value, 0xdeadbeef is returned. The driver has been observed
writing that value back to AR_IMR_S2 after changing a few bits.
Cache the register value in ah->imrs2_reg and always write chached value
to the register.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the workaround limiting chipset TX power to 12dB, instead
using the value configured by the mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable host TX rate control. The wl1271 firmware is already managing rate
control, so this eliminate unnecessary host processing.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of managing the TX security sequence number as two variables, use
one 64 bit variable. This greatly simplifies the handling of the number.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the required block count calculation. Though it
introduces a division operator, it greatly simplifies the formula.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses a higher precision timer to synchronize with the firmware
clock. Improved precision is needed as on some platforms a jiffy may be up to
tens of milliseconds, and the required precision is closer to TU's.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements looped IRQ handling. In essence, if a new interrupt is
asserted by the FW while the host is processing the previous one, the host
will directly proceed processing the new IRQ without leaving the handling
function.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't mask firmware interrupts while processing interrupts. This allows the
interrupt handler looping to work efficiently thus reducing interrupt
processing latency.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will ack RX frames read from the firmware in one single write,
instead of acking all the frames separately. This will reduce the amount of
required communication per frame.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the annoying and dmesg-flooding WLAN PSM entry/exit traces. Instead,
only output them if PSM traces are enabled.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue stopping/waking functionality was broken in a way that could
cause huge latencies in TX transfers and even cause the TX to stall in the
right circumstances. Correct these problems.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ad-hoc mode preventing mac80211 from properly
detecting other ad-hoc networks with the same SSID.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Fix a TX result overflow problem that was present in the TX path and visible
with at least linksys AP's (probably any AP with high throughput capability.)
- Optimize TX by writing FW trigger for a group of TX frames instead of
each and every frame.
- Slightly optimize the TX path code.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most probably patch "wl1271: add most of the normal initialization commands
to PLT mode" enabled the RX path in firmware so that now driver received
frames and passed them to mac80211, which warned about them.
Workaround this by not retrieving frames from the hardware, just ignore them.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed two bugs causing problems when unloding wl1271 module. First was
missing sdio_set_drvdata call from the probe function, second was order
of function calls in the remove function.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed access to fw status register to use raw read instead of
translated addressing. On SDIO access by translated addressing was not
working and raw access is working also on SPI.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added initial implementation of SDIO interfacte to the wl1271 driver.
When selected, this adds new module called "wl1271_sdio".
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Divided wl1271 driver to wl1271 "core" and wl1271_spi modules in preparation
of integration of the SDIO implementation.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removed wl1271_spi.h header as there's no more need to access functions
declared there outside of wl1271_spi.c. Also made those SPI access
functions static.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changed the driver to use if_ops structure to abstract access to the IO
layer (SPI or SDIO).
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moved wl1271 drivers probe, remove etc. functions and structres to
wl1271_spi.c from wl1271_main.c in preparation of implementing SDIO interface.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
P54 devices always generate a full tx_status report
(ACK, PSM, rate control, etc..) for every xmitted frame.
Therefore, I think The driver qualifies for the
REPORTS_TX_ACK_STATUS hardware feature flag.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_hw_register_timeout() was duplicated between phy.c and reset.c.
Since it is too big and too much used to be an inline function, move it
away from the ath5k.h header into reset.c. Remove _ATH5K_RESET and
_ATH5K_PHY defines.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust formatting of the affected lines to satisfy checkpatch.pl.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all unnecessary function declarations from ath5k.h. Comment out
unused functions. Remove ath5k_hw_get_tsf32(), which is too trivial to
be commented out. Make functions static if suggested by sparse. Make
ath5k_pm_ops static.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export rt2x00soc_probe from rt2x00soc as it is used in rt2800pci.
Otherwise loading rt2800pci gives "rt2800pci: Unknown symbol
rt2x00soc_probe".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the wireless summit in Portland we discussed a way of
loading firmware asynchronously from ->probe() before
registration to mac80211, in order to register with the
wireless subsystems with complete information in cases
where firmware is required to know parameters.
This is not yet the case in iwlwifi, but for some new
features we're working on it will be the case since
those will only be supported by new firmware images.
Hence, to start with, convert iwlwifi to load firmware
asynchronously from probe, unbinding the device when
firmware loading fails, and only registering with the
wireless subsystems after firmware has been loaded
successfully.
Future patches will hook into this to register the
new firmware capabilities, depending on the firmware
API version.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts ar9170 to load firmware asynchronously
out of ->probe() and only register with mac80211 when
all firmware has been loaded successfully. If, on the
other hand, any firmware fails to load, it will now
unbind from the device.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Compiling rt2800pci with CONFIG_RT2800PCI_SOC fails with "... rt2880pci.c:
error: incompatible type for argument 2 of 'rt2x00soc_probe'".
Fix this by using &rt2800pci_ops instead of rt2800pci_ops.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for CEIVA USB wireless adapters to the rt73usb driver.
Signed-off-by: Bryan Polk <sainth@eidolons.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The first chunk fixes a debugging assert to print a warning about array underflows.
The second chunk corrects a potential array underflow. I also removed an assert
in the second chunk because it can no longer happen.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even if keylen == 0 is a bug and should not really happen, better avoid
possibility of passing bad value to firmware.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is no longer needed. I missed to remove this in
567ec874d1 ("net: convert multiple
drivers to use netdev_for_each_mc_addr, part6")
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tx/mcc polling, napi_complete() is being incorrectly called
before reaping tx completions. This can cause tx compl processing
to be scheduled on another cpu concurrently which can result in a panic.
This if fixed by calling napi complete() after tx/mcc compl processing
but before re-enabling interrupts (via a cq notify).
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some sis190 devices don't report LinkChange, so do polling for
link status.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11926
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Resending with the proper subject. Sorry for the mess. ]
This patch is based on the RFC of Stanislaw Gruszka.
More specifically it fixes two possible races:
- One, described by Stanislaw, may lead to permanent disabling of the Tx
queue.
This is fixed by adding the smp_wmb() to propagate the BD consumer
change towards the memory.
- Second may lead to bnx2x_start_xmit() returning NETDEV_TX_BUSY.
This is fixed by taking a tx_lock() before rechecking the number of
available Tx BDs.
thanks,
vlad
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-pci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Enable NMI on all cpus on UV
vgaarb: Add user selectability of the number of GPUS in a system
vgaarb: Fix VGA arbiter to accept PCI domains other than 0
x86, uv: Update UV arch to target Legacy VGA I/O correctly.
pci: Update pci_set_vga_state() to call arch functions
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cacheinfo: Enable L3 CID only on AMD
x86, cacheinfo: Remove NUMA dependency, fix for AMD Fam10h rev D1
x86, cpu: Print AMD virtualization features in /proc/cpuinfo
x86, cacheinfo: Calculate L3 indices
x86, cacheinfo: Add cache index disable sysfs attrs only to L3 caches
x86, cacheinfo: Fix disabling of L3 cache indices
intel-agp: Switch to wbinvd_on_all_cpus
x86, lib: Add wbinvd smp helpers
guest to remote communication with vhost net sometimes stops until
guest driver is restarted. This happens when we get guest kick precisely
when the backend send queue is full, as a result handle_tx() returns without
polling backend. This patch fixes this by restarting tx poll on this condition.
Signed-off-by: Sridhar Samudrala <samudrala@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Tom Lendacky <toml@us.ibm.com>
get_user_pages_fast returns number of pages on success, negative value
on failure, but never 0. Fix vhost code to match this logic.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vq log eventfd context pointer needs to be initialized, otherwise
operation may fail or oops if log is enabled but log eventfd not set by
userspace. When log_ctx for device is created, it is copied to the vq.
This reset was missing.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost was dong some complex math to get
offset to log at, and got it wrong by a couple of bytes,
while in fact it's simple: get address where we write,
subtract start of buffer, add log base.
Do it this way.
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Apparently bogus mc address can break IPOIB multicast processing. Therefore
returning the check for addrlen back until this is resolved in bonding (I don't
see any other point from where mc address with non-dev->addr_len length can came
from).
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the VPD searching code is abstracted away, the outer loop used
to detect the read-only large resource data type section is useless.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the VPD searching code is abstracted away, the outer loop used
to detect the read-only large resource data type section is useless.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the pci_vpd_find_info_keyword() helper function to
find information field keywords within read-only and read-write large
resource data type sections.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a preprocessor constant to describe the PCI VPD
information field header size and an inline function to extract the
size of the information field itself.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the pci_vpd_find_tag() helper function to find VPD
resource data types in a buffer.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces more VPD preprocessor definitions to identify some
small and large resource data type item names. The patch then continues
to correct how the tg3 and bnx2 drivers search for the "read-only data"
large resource data type.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a preprocessor constant to describe the PCI VPD large
resource data type tag size and an inline function to extract the large
resource section size from the large resource data type tag.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (88 commits)
powerpc: Fix lwsync feature fixup vs. modules on 64-bit
powerpc: Convert pmc_owner_lock to raw_spinlock
powerpc: Convert die.lock to raw_spinlock
powerpc: Convert tlbivax_lock to raw_spinlock
powerpc: Convert mpic locks to raw_spinlock
powerpc: Convert pmac_pic_lock to raw_spinlock
powerpc: Convert big_irq_lock to raw_spinlock
powerpc: Convert feature_lock to raw_spinlock
powerpc: Convert i8259_lock to raw_spinlock
powerpc: Convert beat_htab_lock to raw_spinlock
powerpc: Convert confirm_error_lock to raw_spinlock
powerpc: Convert ipic_lock to raw_spinlock
powerpc: Convert native_tlbie_lock to raw_spinlock
powerpc: Convert beatic_irq_mask_lock to raw_spinlock
powerpc: Convert nv_lock to raw_spinlock
powerpc: Convert context_lock to raw_spinlock
powerpc/85xx: Add NOR, LEDs and PIB support for MPC8568E-MDS boards
powerpc/86xx: Enable VME driver on the GE SBC610
powerpc/86xx: Enable VME driver on the GE PPC9A
powerpc/86xx: Add MSI section to GE PPC9A DTS
...
Lots of changes. Remove volatile keywords. Take the advice in the comments
and change video_slot to slot_addr. Factor out fifteen or so "channel >>
8" shifts into three shifts higher up the call graph. Make
csc_setpalette() atomic, pass the correct color values. Check for
ioremap() failure. Add missing break statement, thus fixing 24 bit console
visual (blue background bug). Remove some uninformative printk() noise.
Add a description for powerbook 140/170 graphics.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cleanup whitespace and code style. Remove unused #includes and prototypes.
Remove obsolete, redundant or misleading comments. Remove dead code and
redundant initialisers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add the missing mac video modes for the Portrait and 12" RGB displays. The
specs come from the Mac LC III developer note.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The valkyriefb driver needs the CUDA to work in order to set the video
mode at boot. So initialise the device earlier, and bring the m68k code
closer to the powermac code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Valkyriefb and macfb will adopt the same card if they get the chance, so
remove valkyrie support from macfb. Also fix the "valkyriefb: can't do
832x624x8" problem reported by Raylynn Knight some time ago, by adding
vmode 13 support for CONFIG_MAC. Also add vmode 11 since that works too.
Make use of the monitor sense lines on 68k Macs too. Also some cleanups.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The valkyriefb driver assumes that this logic holds:
mac_vmode_to_var(X, cmode, &var);
mac_var_to_vmode(&var, &vmode, &cmode);
assert(vmode == X);
But it doesn't hold because mac_var_to_vmode() can return a mode with a
slower pixel clock, even when a match is available. So we end up with this
failure:
using video mode 11 and color mode 0.
valkyriefb: vmode 12 not valid.
valkyriefb: can't set default video mode
valkyriefb: vmode 12 not valid.
Rather than have mac_var_to_mode() return the first reasonable mode it
finds, have it return the mode that is closest to the requested one (or
the mode with the closest longer pixel clock period if there is no exact
match).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move platform device code from the drivers to the platform init function.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move platform device code from the driver to the platform init function.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add platform driver support to the pmac-zilog driver, for m68k macs.
Place the powermac-specific code inside #ifdef CONFIG_PPC_PMAC.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Adjust the platform device code to conform with the code style used in the
rest of this patch series. No need to name resources nor to register
devices which are not applicable.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Trivial patch which adds the __init macro to the module_init
function and all of its helper functions of drivers/char/vme_scc.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The debugfs support of the Marvell driver is buggy. It is limited to one
controller per system. Fix this by using the controller specific debugfs
directory as parent.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make bcm203x_table also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Trivial patch which adds the __init/__exit macros to the module_init/
module_exit functions of btmrvl_sdio.c driver.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On Alchemy the PCMCIA area lies at the end of the chips 36bit system bus
area. Currently, addresses at the far end of the 32bit area are assumed
to belong to the PCMCIA area and fixed up to the real 36bit address before
being passed to ioremap().
A previous commit enabled 64 bit physical size for the resource datatype on
Alchemy and this allows to use the correct 36bit addresses when registering
the PCMCIA sockets.
This patch removes the 32-to-36bit address fixup and registers the Alchemy
demo board pcmcia socket with the correct 36bit physical addresses.
Tested on DB1200, with a CF card (ide-cs driver) and a 3c589 PCMCIA ethernet
card.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/994/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If we wait for the once-per-second cleanup to free transmit SKBs,
sockets with small transmit buffer sizes might spend most of their
time blocked waiting for the cleanup.
Normally we do a cleanup for each transmitted packet. We add a
watchdog type timer so that we also schedule a timeout for 150uS after
a packet is transmitted. The watchdog is reset for each transmitted
packet, so for high packet rates, it never expires. At these high
rates, the cleanups are done for each packet so the extra watchdog
initiated cleanups are neither needed nor triggered.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: netdev@vger.kernel.org
To: gregkh@suse.de
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/968/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This version has spelling and comment changes based on feedback from
Eric Dumazet.
Although the hardware supports a 4/8bit SD interface and the driver
unconditionally advertises all hardware caps to the MMC core, not all
datalines may actually be wired up. This patch introduces another
field to au1xmmc platform data allowing platforms to disable certain
advanced host controller features.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: linux-mmc@vger.kernel.org
CC: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch makes the ar7 clock code implement the Linux clk API. Drivers
using the various clocks available in the SoC are updated accordingly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
To: linux-mips@linux-mips.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: netdev@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Patchwork: http://patchwork.linux-mips.org/patch/881/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Octeon ethernet hardware can handle NETIF_F_SG, so we enable it.
A gather list of up to six fragments will fit in the SKB's CB
structure, so no extra memory is required. If a SKB has more than six
fragments, we must linearize it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the driver to be a reasonably well behaved NAPI citizen.
There is one NAPI instance per CPU shared between all input ports. As
receive backlog increases, NAPI is scheduled on additional CPUs.
Receive buffer refill code factored out so it can also be called from
the periodic timer. This is needed to recover from temporary buffer
starvation conditions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/839/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Stop the queue if too many packets are queued. Restart it from a high
resolution timer.
Rearrange and simplify locking and SKB freeing code
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: gregkh@suse.de
Patchwork: http://patchwork.linux-mips.org/patch/843/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
After aligning the blocks returned by kmalloc, we need to save the original
pointer so they can be correctly freed.
There are no guarantees about the alignment of SKB data, so we need to
handle worst case alignment.
Since right shifts over subtraction have no distributive property, we need
to fix the back pointer calculation.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch converts the au1000-eth driver to become a full platform-driver
as it ought to be. We now pass PHY-speficic configurations through
platform_data but for compatibility the driver still assumes the default
settings (search for PHY1 on MAC0) when no platform_data is passed. Tested
on my MTX-1 board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: http://patchwork.linux-mips.org/patch/619/
Patchwork: http://patchwork.linux-mips.org/patch/963/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace the devboard NOR MTD mapping driver with physmap-flash support.
Also honor the "swapboot" switch settings wrt. to the layout of the
NOR partitions.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Limit the amount of address space claimed for Alchemy serial ports to
0x1000. On the Au1300, ports are only 0x1000 apart, and the registers
only extend to 0x110 at most on all supported alchemy models.
On the Au1300 the autodetect logic no longer works and this makes it
necessary to specify the port type through platform data. Because of
this the MSR quirk needs to be moved outside the autoconfig() function
which will no longer be called when UPF_FIXED_TYPE is specified.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.
(Queueing function signature has changed in order to give
a build failure instead of silent functional changes due
to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
- supports Db1000, DB/PB1100/1500/1550/1200.
- support for carddetect and statuschange IRQs.
- pcmcia socket mem/io/attr areas and irqs passed through
platform resource information.
- doesn't freeze system during card insertion/ejection like
the one it replaces.
- boardtype is automatically detected using BCSR ID register.
Run-tested on the DB1200.
Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move TC_PRIO_CONTROL check and queue remapping into
ixgbe_select_queue(). Remapping queues after the qdisc
can result in the wrong qdisc queue being stopped with
netif_stop_subqueue(). Even if this is resolved and the
correct queue is stopped it can result in a queue being
blocked by TC_PRIO_CONTROL frames uneccesarily. Moving
this into the select_queue routine maintains alignment
between tx_rings and qdisc queues.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the register_netdevice() call fails, the newly allocated device is
not freed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit e8469ed959c373c2ff9e6f488aa5a14971aebe1f
Author: Patrick McHardy <kaber@trash.net>
Date: Tue Feb 23 20:41:30 2010 +0100
Support specifying the initial device flags when creating a device though
rtnl_link. Devices allocated by rtnl_create_link() are marked as INITIALIZING
in order to surpress netlink registration notifications. To complete setup,
rtnl_configure_link() must be called, which performs the device flag changes
and invokes the deferred notifiers if everything went well.
Two examples:
# add macvlan to eth0
#
$ ip link add link eth0 up allmulticast on type macvlan
[LINK]11: macvlan0@eth0: <BROADCAST,MULTICAST,ALLMULTI,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN
link/ether 26:f8:84:02:f9:2a brd ff:ff:ff:ff:ff:ff
[ROUTE]ff00::/8 dev macvlan0 table local metric 256 mtu 1500 advmss 1440 hoplimit 0
[ROUTE]fe80::/64 dev macvlan0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0
[LINK]11: macvlan0@eth0: <BROADCAST,MULTICAST,ALLMULTI,UP,LOWER_UP> mtu 1500
link/ether 26:f8:84:02:f9:2a
[ADDR]11: macvlan0 inet6 fe80::24f8:84ff:fe02:f92a/64 scope link
valid_lft forever preferred_lft forever
[ROUTE]local fe80::24f8:84ff:fe02:f92a via :: dev lo table local proto none metric 0 mtu 16436 advmss 16376 hoplimit 0
[ROUTE]default via fe80::215:e9ff:fef0:10f8 dev macvlan0 proto kernel metric 1024 mtu 1500 advmss 1440 hoplimit 0
[NEIGH]fe80::215:e9ff:fef0:10f8 dev macvlan0 lladdr 00:15:e9:f0:10:f8 router STALE
[ROUTE]2001:6f8:974::/64 dev macvlan0 proto kernel metric 256 expires 0sec mtu 1500 advmss 1440 hoplimit 0
[PREFIX]prefix 2001:6f8:974::/64 dev macvlan0 onlink autoconf valid 14400 preferred 131084
[ADDR]11: macvlan0 inet6 2001:6f8:974:0:24f8:84ff:fe02:f92a/64 scope global dynamic
valid_lft 86399sec preferred_lft 14399sec
# add VLAN to eth1, eth1 is down
#
$ ip link add link eth1 up type vlan id 1000
RTNETLINK answers: Network is down
<no events>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPC5121 FEC requeries 4-byte alignmnent for TX data buffers.
This patch is a work around that copies misaligned tx packets
to an aligned skb before sending.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the fs_enet driver to support MPC512x FEC.
Enable it with CONFIG_FS_ENET_MPC5121_FEC option.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
toshiba_acpi: Add full hotkey support
hp-wmi: Add support for tablet rotation key
dell-laptop: Add another Dell laptop to the DMI whitelist
classmate-laptop: use a single MODULE_DEVICE_TABLE to get correct aliases
dell-laptop: Pay attention to which devices the hardware switch controls
dell-laptop: Use buffer with 32-bit physical address
dell-laptop: Blacklist machines not supporting dell-laptop
dell-laptop: Block software state changes when rfkill hard blocked
dell-laptop: Fix small memory leak
dell-laptop: Fix platform device unregistration
dell-laptop: Update rfkill state on kill switch
compal-laptop: Replace sysfs support with rfkill support
compal-laptop: Add support for known Compal made Dell laptops
MAINTAINERS: update drivers/platform/x86 information
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (362 commits)
V4L-DVB: cx88-dvb: remove extra attribution for core
V4L/DVB: v4l: soc_camera: fix bound checking of mbus_fmt[] index
V4L/DVB: Add support for SMT7020 to cx88
V4L/DVB: radio-si470x: Use UTF-8 encoding on a comment
V4L/DVB: MAINTAINERS: Telegent tlg2300 section fix
V4L/DVB: gspca_stv06xx: Add support for camera button
V4L/DVB: gspca_ov519: add support for the button on ov511 based cams
V4L/DVB: gspca_ov519: Add support for the button on ov518 based cams
V4L/DVB: gspca_ov519: add support for the button on ov519 based cams
V4L/DVB: gspca_main: Fix a compile error when CONFIG_INPUT is not set
V4L/DVB: gspca_main: some input error handling fixes
V4L/DVB: gspca_main: Allow use of input device creation code for non int. inputs
V4L/DVB: gspca_pac7302: much improved exposure control
V4L/DVB: gspca_sonixb: Make sonixb driver handle pas106 and pas202 cameras
V4L/DVB: gspca_sonixb: pas106: fixup bright ctrl and add gain and exposure ctrls
V4L/DVB: Documentation: gspca.txt: update known mr97310a cams
V4L/DVB: gspca_mr97310a: add support for the Sakar 1638x CyberPix
V4L/DVB: gscpa_sonixb: limit ov7630 max framerate at 640x480
V4L/DVB: gspca_sonixb: pas202: fixup brightness ctrl and add gain and exposure ctrls
V4L/DVB: gscpa_sonixb: Differentiate between sensors with a coarse and fine expo ctrl
...