Similar to previous change, this time for eache and timestamp.
Unlike helper and acct, these can be disabled at build time, so they
need ifdef guards.
Next patch will remove a few (now obsolete) functions.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Needless copy&paste, just handle all in one. Next patch will handle
acct and timestamp, which have similar functions.
Intentionally leaves cruft behind, will be cleaned up in a followup
patch.
The obsolete sysctl pointers in netns_ct struct are left in place and
removed in a single change, as changes to netns trigger rebuild of
almost all files.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Its a bit hard to see what table[3] really lines up with, so add
human-readable mnemonics and use them for initialisation.
This makes it easier to see e.g. which sysctls are not exported to
unprivileged userns.
objdiff shows no changes.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds two sysctl knobs for GRE:
net.netfilter.nf_conntrack_gre_timeout = 30
net.netfilter.nf_conntrack_gre_timeout_stream = 180
Update the Documentation as well.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We have no explicit signal when a UDP stream has terminated, peers just
stop sending.
For suspected stream connections a timeout of two minutes is sane to keep
NAT mapping alive a while longer.
It matches tcp conntracks 'timewait' default timeout value.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently DNS resolvers that send both A and AAAA queries from same source port
can trigger stream mode prematurely, which results in non-early-evictable conntrack entry
for three minutes, even though DNS requests are done in a few milliseconds.
Add a two second grace period where we continue to use the ordinary
30-second default timeout. Its enough for DNS request/response traffic,
even if two request/reply packets are involved.
ASSURED is still set, else conntrack (and thus a possible
NAT mapping ...) gets zapped too in case conntrack table runs full.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The existing code did not expect users would initialize the TLS ULP
without subsequently calling the TLS TX enabling socket option.
If the application tries to send data after the TLS ULP enable op
but before the TLS TX enable op the BPF sk_msg verdict program is
skipped. This patch resolves this by converting the ipv4 sock ops
to be calculated at init time the same way ipv6 ops are done. This
pulls in any changes to the sock ops structure that have been made
after the socket was created including the changes from adding the
socket to a sock{map|hash}.
This was discovered by running OpenSSL master branch which calls
the TLS ULP setsockopt early in TLS handshake but only enables
the TLS TX path once the handshake has completed. As a result the
datapath missed the initial handshake messages.
Fixes: 02c558b2d5 ("bpf: sockmap, support for msg_peek in sk_msg with redirect ingress")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
A sockmap program that redirects through a kTLS ULP enabled socket
will not work correctly because the ULP layer is skipped. This
fixes the behavior to call through the ULP layer on redirect to
ensure any operations required on the data stream at the ULP layer
continue to be applied.
To do this we add an internal flag MSG_SENDPAGE_NOPOLICY to avoid
calling the BPF layer on a redirected message. This is
required to avoid calling the BPF layer multiple times (possibly
recursively) which is not the current/expected behavior without
ULPs. In the future we may add a redirect flag if users _do_
want the policy applied again but this would need to work for both
ULP and non-ULP sockets and be opt-in to avoid breaking existing
programs.
Also to avoid polluting the flag space with an internal flag we
reuse the flag space overlapping MSG_SENDPAGE_NOPOLICY with
MSG_WAITFORONE. Here WAITFORONE is specific to recv path and
SENDPAGE_NOPOLICY is only used for sendpage hooks. The last thing
to verify is user space API is masked correctly to ensure the flag
can not be set by user. (Note this needs to be true regardless
because we have internal flags already in-use that user space
should not be able to set). But for completeness we have two UAPI
paths into sendpage, sendfile and splice.
In the sendfile case the function do_sendfile() zero's flags,
./fs/read_write.c:
static ssize_t do_sendfile(int out_fd, int in_fd, loff_t *ppos,
size_t count, loff_t max)
{
...
fl = 0;
#if 0
/*
* We need to debate whether we can enable this or not. The
* man page documents EAGAIN return for the output at least,
* and the application is arguably buggy if it doesn't expect
* EAGAIN on a non-blocking file descriptor.
*/
if (in.file->f_flags & O_NONBLOCK)
fl = SPLICE_F_NONBLOCK;
#endif
file_start_write(out.file);
retval = do_splice_direct(in.file, &pos, out.file, &out_pos, count, fl);
}
In the splice case the pipe_to_sendpage "actor" is used which
masks flags with SPLICE_F_MORE.
./fs/splice.c:
static int pipe_to_sendpage(struct pipe_inode_info *pipe,
struct pipe_buffer *buf, struct splice_desc *sd)
{
...
more = (sd->flags & SPLICE_F_MORE) ? MSG_MORE : 0;
...
}
Confirming what we expect that internal flags are in fact internal
to socket side.
Fixes: d3b18ad31f ("tls: add bpf support to sk_msg handling")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In addition to releasing any cork'ed data on a psock when the psock
is removed we should also release any skb's in the ingress work queue.
Otherwise the skb's eventually get free'd but late in the tear
down process so we see the WARNING due to non-zero sk_forward_alloc.
void sk_stream_kill_queues(struct sock *sk)
{
...
WARN_ON(sk->sk_forward_alloc);
...
}
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When a skb verdict program is in-use and either another BPF program
redirects to that socket or the new SK_PASS support is used the
data_ready callback does not wake up application. Instead because
the stream parser/verdict is using the sk data_ready callback we wake
up the stream parser/verdict block.
Fix this by adding a helper to check if the stream parser block is
enabled on the sk and if so call the saved pointer which is the
upper layers wake up function.
This fixes application stalls observed when an application is waiting
for data in a blocking read().
Fixes: d829e9c411 ("tls: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add SK_PASS verdict support to SK_SKB_VERDICT programs. Now that
support for redirects exists we can implement SK_PASS as a redirect
to the same socket. This simplifies the BPF programs and avoids an
extra map lookup on RX path for simple visibility cases.
Further, reduces user (BPF programmer in this context) confusion
when their program drops skb due to lack of support.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Enforce comment on structure layout dependency with a BUILD_BUG_ON
to ensure the condition is maintained.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The check for max offset in sk_msg_is_valid_access uses sizeof()
which is incorrect because it would allow accessing possibly
past the end of the struct in the padded case. Further, it doesn't
preclude accessing any padding that may be added in the middle of
a struct. All told this makes it fragile to rely on.
To fix this explicitly check offsets with fields using the
bpf_ctx_range() and bpf_ctx_range_till() macros.
For reference the current structure layout looks as follows (reported
by pahole)
struct sk_msg_md {
union {
void * data; /* 8 */
}; /* 0 8 */
union {
void * data_end; /* 8 */
}; /* 8 8 */
__u32 family; /* 16 4 */
__u32 remote_ip4; /* 20 4 */
__u32 local_ip4; /* 24 4 */
__u32 remote_ip6[4]; /* 28 16 */
__u32 local_ip6[4]; /* 44 16 */
__u32 remote_port; /* 60 4 */
/* --- cacheline 1 boundary (64 bytes) --- */
__u32 local_port; /* 64 4 */
__u32 size; /* 68 4 */
/* size: 72, cachelines: 2, members: 10 */
/* last cacheline: 8 bytes */
};
So there should be no padding at the moment but fixing this now
prevents future errors.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-12-20
Two last patches for this release cycle:
1) Remove an unused variable in xfrm_policy_lookup_bytype().
From YueHaibing.
2) Fix possible infinite loop in __xfrm6_tunnel_alloc_spi().
Also from YueHaibing.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NDA_PROTOCOL to nda_policy and use the policy for attribute parsing and
validation for adding neighbors and in dump requests. Remove the now duplicate
checks on nla_len.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Off by one in netlink parsing of mac802154_hwsim, from Alexander
Aring.
2) nf_tables RCU usage fix from Taehee Yoo.
3) Flow dissector needs nhoff and thoff clamping, from Stanislav
Fomichev.
4) Missing sin6_flowinfo initialization in SCTP, from Xin Long.
5) Spectrev1 in ipmr and ip6mr, from Gustavo A. R. Silva.
6) Fix r8169 crash when DEBUG_SHIRQ is enabled, from Heiner Kallweit.
7) Fix SKB leak in rtlwifi, from Larry Finger.
8) Fix state pruning in bpf verifier, from Jakub Kicinski.
9) Don't handle completely duplicate fragments as overlapping, from
Michal Kubecek.
10) Fix memory corruption with macb and 64-bit DMA, from Anssi Hannula.
11) Fix TCP fallback socket release in smc, from Myungho Jung.
12) gro_cells_destroy needs to napi_disable, from Lorenzo Bianconi.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (130 commits)
rds: Fix warning.
neighbor: NTF_PROXY is a valid ndm_flag for a dump request
net: mvpp2: fix the phylink mode validation
net/sched: cls_flower: Remove old entries from rhashtable
net/tls: allocate tls context using GFP_ATOMIC
iptunnel: make TUNNEL_FLAGS available in uapi
gro_cell: add napi_disable in gro_cells_destroy
lan743x: Remove MAC Reset from initialization
net/mlx5e: Remove the false indication of software timestamping support
net/mlx5: Typo fix in del_sw_hw_rule
net/mlx5e: RX, Fix wrong early return in receive queue poll
ipv6: explicitly initialize udp6_addr in udp_sock_create6()
bnxt_en: Fix ethtool self-test loopback.
net/rds: remove user triggered WARN_ON in rds_sendmsg
net/rds: fix warn in rds_message_alloc_sgs
ath10k: skip sending quiet mode cmd for WCN3990
mac80211: free skb fraglist before freeing the skb
nl80211: fix memory leak if validate_pae_over_nl80211() fails
net/smc: fix TCP fallback socket release
vxge: ensure data0 is initialized in when fetching firmware version information
...
>> net/rds/send.c:1109:42: warning: Using plain integer as NULL pointer
Fixes: ea010070d0 ("net/rds: fix warn in rds_message_alloc_sgs")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping proxy entries the dump request has NTF_PROXY set in
ndm_flags. strict mode checking needs to be updated to allow this
flag.
Fixes: 51183d233b ("net/neighbor: Update neigh_dump_info for strict data checking")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pneigh_lookup uses kmalloc versus kzalloc when new entries are allocated.
Given that the newly added protocol field needs to be initialized.
Fixes: df9b0e30d4 ("neighbor: Add protocol attribute")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When replacing a rule we add the new rule to the rhashtable
but only remove the old if not in skip_sw.
This commit fix this and remove the old rule anyway.
Fixes: 35cc3cefc4 ("net/sched: cls_flower: Reject duplicated rules also under skip_sw")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch registers neigh doit handler. The doit handler
returns a neigh entry given dst and dev. This is similar
to route and fdb doit (get) handlers. Also moves nda_policy
declaration from rtnetlink.c to neighbour.c
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior this commit, when the struct socket object was being released,
the UMEM did not have its reference count decreased. Instead, this was
done in the struct sock sk_destruct function.
There is no reason to keep the UMEM reference around when the socket
is being orphaned, so in this patch the xdp_put_mem is called in the
xsk_release function. This results in that the xsk_destruct function
can be removed!
Note that, it still holds that a struct xsk_sock reference might still
linger in the XSKMAP after the UMEM is released, e.g. if a user does
not clear the XSKMAP prior to closing the process. This sock will be
in a "released" zombie like state, until the XSKMAP is removed.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
syzbot reported the use of uninitialized udp6_addr::sin6_scope_id.
We can just set ::sin6_scope_id to zero, as tunnels are unlikely
to use an IPv6 address that needs a scope id and there is no
interface to bind in this context.
For net-next, it looks different as we have cfg->bind_ifindex there
so we can probably call ipv6_iface_scope_id().
Same for ::sin6_flowinfo, tunnels don't use it.
Fixes: 8024e02879 ("udp: Add udp_sock_create for UDP tunnels to open listener socket")
Reported-by: syzbot+c56449ed3652e6720f30@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending broadcast message on high load system, there are a lot of
unnecessary packets restranmission. That issue was caused by missing in
initial criteria for retransmission.
To prevent this happen, just initialize this criteria for retransmission
in next 10 milliseconds.
Fixes: 31c4f4cc32 ("tipc: improve broadcast retransmission algorithm")
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit adds the new trace_event for TIPC bearer, L2 device event:
trace_tipc_l2_device_event()
Also, it puts the trace at the tipc_l2_device_event() function, then
the device/bearer events and related info can be traced out during
runtime when needed.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit adds the new trace_events for TIPC node object:
trace_tipc_node_create()
trace_tipc_node_delete()
trace_tipc_node_lost_contact()
trace_tipc_node_timeout()
trace_tipc_node_link_up()
trace_tipc_node_link_down()
trace_tipc_node_reset_links()
trace_tipc_node_fsm_evt()
trace_tipc_node_check_state()
Also, enables the traces for the following cases:
- When a node is created/deleted;
- When a node contact is lost;
- When a node timer is timed out;
- When a node link is up/down;
- When all node links are reset;
- When node state is changed;
- When a skb comes and node state needs to be checked/updated.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit adds the new trace_events for TIPC socket object:
trace_tipc_sk_create()
trace_tipc_sk_poll()
trace_tipc_sk_sendmsg()
trace_tipc_sk_sendmcast()
trace_tipc_sk_sendstream()
trace_tipc_sk_filter_rcv()
trace_tipc_sk_advance_rx()
trace_tipc_sk_rej_msg()
trace_tipc_sk_drop_msg()
trace_tipc_sk_release()
trace_tipc_sk_shutdown()
trace_tipc_sk_overlimit1()
trace_tipc_sk_overlimit2()
Also, enables the traces for the following cases:
- When user creates a TIPC socket;
- When user calls poll() on TIPC socket;
- When user sends a dgram/mcast/stream message.
- When a message is put into the socket 'sk_receive_queue';
- When a message is released from the socket 'sk_receive_queue';
- When a message is rejected (e.g. due to no port, invalid, etc.);
- When a message is dropped (e.g. due to wrong message type);
- When socket is released;
- When socket is shutdown;
- When socket rcvq's allocation is overlimit (> 90%);
- When socket rcvq + bklq's allocation is overlimit (> 90%);
- When the 'TIPC_ERR_OVERLOAD/2' issue happens;
Note:
a) All the socket traces are designed to be able to trace on a specific
socket by either using the 'event filtering' feature on a known socket
'portid' value or the sysctl file:
/proc/sys/net/tipc/sk_filter
The file determines a 'tuple' for what socket should be traced:
(portid, sock type, name type, name lower, name upper)
where:
+ 'portid' is the socket portid generated at socket creating, can be
found in the trace outputs or the 'tipc socket list' command printouts;
+ 'sock type' is the socket type (1 = SOCK_TREAM, ...);
+ 'name type', 'name lower' and 'name upper' are the service name being
connected to or published by the socket.
Value '0' means 'ANY', the default tuple value is (0, 0, 0, 0, 0) i.e.
the traces happen for every sockets with no filter.
b) The 'tipc_sk_overlimit1/2' event is also a conditional trace_event
which happens when the socket receive queue (and backlog queue) is
about to be overloaded, when the queue allocation is > 90%. Then, when
the trace is enabled, the last skbs leading to the TIPC_ERR_OVERLOAD/2
issue can be traced.
The trace event is designed as an 'upper watermark' notification that
the other traces (e.g. 'tipc_sk_advance_rx' vs 'tipc_sk_filter_rcv') or
actions can be triggerred in the meanwhile to see what is going on with
the socket queue.
In addition, the 'trace_tipc_sk_dump()' is also placed at the
'TIPC_ERR_OVERLOAD/2' case, so the socket and last skb can be dumped
for post-analysis.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit adds the new trace_events for TIPC link object:
trace_tipc_link_timeout()
trace_tipc_link_fsm()
trace_tipc_link_reset()
trace_tipc_link_too_silent()
trace_tipc_link_retrans()
trace_tipc_link_bc_ack()
trace_tipc_link_conges()
And the traces for PROTOCOL messages at building and receiving:
trace_tipc_proto_build()
trace_tipc_proto_rcv()
Note:
a) The 'tipc_link_too_silent' event will only happen when the
'silent_intv_cnt' is about to reach the 'abort_limit' value (and the
event is enabled). The benefit for this kind of event is that we can
get an early indication about TIPC link loss issue due to timeout, then
can do some necessary actions for troubleshooting.
For example: To trigger the 'tipc_proto_rcv' when the 'too_silent'
event occurs:
echo 'enable_event:tipc:tipc_proto_rcv' > \
events/tipc/tipc_link_too_silent/trigger
And disable it when TIPC link is reset:
echo 'disable_event:tipc:tipc_proto_rcv' > \
events/tipc/tipc_link_reset/trigger
b) The 'tipc_link_retrans' or 'tipc_link_bc_ack' event is useful to
trace TIPC retransmission issues.
In addition, the commit adds the 'trace_tipc_list/link_dump()' at the
'retransmission failure' case. Then, if the issue occurs, the link
'transmq' along with the link data can be dumped for post-analysis.
These dump events should be enabled by default since it will only take
effect when the failure happens.
The same approach is also applied for the faulty case that the
validation of protocol message is failed.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for the sake of debugging/tracing, the commit enables tracepoints in
TIPC along with some general trace_events as shown below. It also
defines some 'tipc_*_dump()' functions that allow to dump TIPC object
data whenever needed, that is, for general debug purposes, ie. not just
for the trace_events.
The following trace_events are now available:
- trace_tipc_skb_dump(): allows to trace and dump TIPC msg & skb data,
e.g. message type, user, droppable, skb truesize, cloned skb, etc.
- trace_tipc_list_dump(): allows to trace and dump any TIPC buffers or
queues, e.g. TIPC link transmq, socket receive queue, etc.
- trace_tipc_sk_dump(): allows to trace and dump TIPC socket data, e.g.
sk state, sk type, connection type, rmem_alloc, socket queues, etc.
- trace_tipc_link_dump(): allows to trace and dump TIPC link data, e.g.
link state, silent_intv_cnt, gap, bc_gap, link queues, etc.
- trace_tipc_node_dump(): allows to trace and dump TIPC node data, e.g.
node state, active links, capabilities, link entries, etc.
How to use:
Put the trace functions at any places where we want to dump TIPC data
or events.
Note:
a) The dump functions will generate raw data only, that is, to offload
the trace event's processing, it can require a tool or script to parse
the data but this should be simple.
b) The trace_tipc_*_dump() should be reserved for a failure cases only
(e.g. the retransmission failure case) or where we do not expect to
happen too often, then we can consider enabling these events by default
since they will almost not take any effects under normal conditions,
but once the rare condition or failure occurs, we get the dumped data
fully for post-analysis.
For other trace purposes, we can reuse these trace classes as template
but different events.
c) A trace_event is only effective when we enable it. To enable the
TIPC trace_events, echo 1 to 'enable' files in the events/tipc/
directory in the 'debugfs' file system. Normally, they are located at:
/sys/kernel/debug/tracing/events/tipc/
For example:
To enable the tipc_link_dump event:
echo 1 > /sys/kernel/debug/tracing/events/tipc/tipc_link_dump/enable
To enable all the TIPC trace_events:
echo 1 > /sys/kernel/debug/tracing/events/tipc/enable
To collect the trace data:
cat trace
or
cat trace_pipe > /trace.out &
To disable all the TIPC trace_events:
echo 0 > /sys/kernel/debug/tracing/events/tipc/enable
To clear the trace buffer:
echo > trace
d) Like the other trace_events, the feature like 'filter' or 'trigger'
is also usable for the tipc trace_events.
For more details, have a look at:
Documentation/trace/ftrace.txt
MAINTAINERS | add two new files 'trace.h' & 'trace.c' in tipc
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove skb->sp and allocate secpath storage via extension
infrastructure. This also reduces sk_buff by 8 bytes on x86_64.
Total size of allyesconfig kernel is reduced slightly, as there is
less inlined code (one conditional atomic op instead of two on
skb_clone).
No differences in throughput in following ipsec performance tests:
- transport mode with aes on 10GB link
- tunnel mode between two network namespaces with aes and null cipher
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
secpath_set is a wrapper for secpath_dup that will not perform
an allocation if the secpath attached to the skb has a reference count
of one, i.e., it doesn't need to be COW'ed.
Also, secpath_dup doesn't attach the secpath to the skb, it leaves
this to the caller.
Use secpath_set in places that immediately assign the return value to
skb.
This allows to remove skb->sp without touching these spots again.
secpath_dup can eventually be removed in followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will reduce noise when skb->sp is removed later in this series.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_sec_path gains 'const' qualifier to avoid
xt_policy.c: 'skb_sec_path' discards 'const' qualifier from pointer target type
same reasoning as previous conversions: Won't need to touch these
spots anymore when skb->sp is removed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future patch will remove skb->sp pointer.
To reduce noise in those patches, move existing helper to
sk_buff and use it in more places to ease skb->sp replacement later.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It can only return 0 (success) or -ENOMEM.
Change return value to a pointer to secpath struct.
This avoids direct access to skb->sp:
err = secpath_set(skb);
if (!err) ..
skb->sp-> ...
Becomes:
sp = secpath_set(skb)
if (!sp) ..
sp-> ..
This reduces noise in followup patch which is going to remove skb->sp.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts the bridge netfilter (calling iptables hooks from bridge)
facility to use the extension infrastructure.
The bridge_nf specific hooks in skb clone and free paths are removed, they
have been replaced by the skb_ext hooks that do the same as the bridge nf
allocations hooks did.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an optional extension infrastructure, with ispec (xfrm) and
bridge netfilter as first users.
objdiff shows no changes if kernel is built without xfrm and br_netfilter
support.
The third (planned future) user is Multipath TCP which is still
out-of-tree.
MPTCP needs to map logical mptcp sequence numbers to the tcp sequence
numbers used by individual subflows.
This DSS mapping is read/written from tcp option space on receive and
written to tcp option space on transmitted tcp packets that are part of
and MPTCP connection.
Extending skb_shared_info or adding a private data field to skb fclones
doesn't work for incoming skb, so a different DSS propagation method would
be required for the receive side.
mptcp has same requirements as secpath/bridge netfilter:
1. extension memory is released when the sk_buff is free'd.
2. data is shared after cloning an skb (clone inherits extension)
3. adding extension to an skb will COW the extension buffer if needed.
The "MPTCP upstreaming" effort adds SKB_EXT_MPTCP extension to store the
mapping for tx and rx processing.
Two new members are added to sk_buff:
1. 'active_extensions' byte (filling a hole), telling which extensions
are available for this skb.
This has two purposes.
a) avoids the need to initialize the pointer.
b) allows to "delete" an extension by clearing its bit
value in ->active_extensions.
While it would be possible to store the active_extensions byte
in the extension struct instead of sk_buff, there is one problem
with this:
When an extension has to be disabled, we can always clear the
bit in skb->active_extensions. But in case it would be stored in the
extension buffer itself, we might have to COW it first, if
we are dealing with a cloned skb. On kmalloc failure we would
be unable to turn an extension off.
2. extension pointer, located at the end of the sk_buff.
If the active_extensions byte is 0, the pointer is undefined,
it is not initialized on skb allocation.
This adds extra code to skb clone and free paths (to deal with
refcount/free of extension area) but this replaces similar code that
manages skb->nf_bridge and skb->sp structs in the followup patches of
the series.
It is possible to add support for extensions that are not preseved on
clones/copies.
To do this, it would be needed to define a bitmask of all extensions that
need copy/cow semantics, and change __skb_ext_copy() to check
->active_extensions & SKB_EXT_PRESERVE_ON_CLONE, then just set
->active_extensions to 0 on the new clone.
This isn't done here because all extensions that get added here
need the copy/cow semantics.
v2:
Allocate entire extension space using kmem_cache.
Upside is that this allows better tracking of used memory,
downside is that we will allocate more space than strictly needed in
most cases (its unlikely that all extensions are active/needed at same
time for same skb).
The allocated memory (except the small extension header) is not cleared,
so no additonal overhead aside from memory usage.
Avoid atomic_dec_and_test operation on skb_ext_put()
by using similar trick as kfree_skbmem() does with fclone_ref:
If recount is 1, there is no concurrent user and we can free right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pointer is going to be removed soon, so use the existing helpers in
more places to avoid noise when the removal happens.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
1/ discard 'struct unx_cred'. We don't need any data that
is not already in 'struct rpc_cred'.
2/ Don't keep these creds in a hash table. When a credential
is needed, simply allocate it. When not needed, discard it.
This can easily be faster than performing a lookup on
a shared hash table.
As the lookup can happen during write-out, use a mempool
to ensure forward progress.
This means that we cannot compare two credentials for
equality by comparing the pointers, but we never do that anyway.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
This now always just does get_rpccred(), so we
don't need an operation pointer to know to do that.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
SUNRPC has two sorts of credentials, both of which appear as
"struct rpc_cred".
There are "generic credentials" which are supplied by clients
such as NFS and passed in 'struct rpc_message' to indicate
which user should be used to authorize the request, and there
are low-level credentials such as AUTH_NULL, AUTH_UNIX, AUTH_GSS
which describe the credential to be sent over the wires.
This patch replaces all the generic credentials by 'struct cred'
pointers - the credential structure used throughout Linux.
For machine credentials, there is a special 'struct cred *' pointer
which is statically allocated and recognized where needed as
having a special meaning. A look-up of a low-level cred will
map this to a machine credential.
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
NFS needs to know when a credential is about to expire so that
it can modify write-back behaviour to finish the write inside the
expiry time.
It currently uses functions in SUNRPC code which make use of a
fairly complex callback scheme and flags in the generic credientials.
As I am working to discard the generic credentials, this has to change.
This patch moves the logic into NFS, in part by finding and caching
the low-level credential in the open_context. We then make direct
cred-api calls on that.
This makes the code much simpler and removes a dependency on generic
rpc credentials.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The credential passed in rpc_message.rpc_cred is always a
generic credential except in one instance.
When gss_destroying_context() calls rpc_call_null(), it passes
a specific credential that it needs to destroy.
In this case the RPC acts *on* the credential rather than
being authorized by it.
This special case deserves explicit support and providing that will
mean that rpc_message.rpc_cred is *always* generic, allowing
some optimizations.
So add "tk_op_cred" to rpc_task and "rpc_op_cred" to the setup data.
Use this to pass the cred down from rpc_call_null(), and have
rpcauth_bindcred() notice it and bind it in place.
Credit to kernel test robot <fengguang.wu@intel.com> for finding
a bug in earlier version of this patch.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
In almost all cases the credential stored in rpc_message.rpc_cred
is a "generic" credential. One of the two expections is when an
AUTH_NULL credential is used such as for RPC ping requests.
To improve consistency, don't pass an explicit credential in
these cases, but instead pass NULL and set a task flag,
similar to RPC_TASK_ROOTCREDS, which requests that NULL credentials
be used by default.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
When NFS creates a machine credential, it is a "generic" credential,
not tied to any auth protocol, and is really just a container for
the princpal name.
This doesn't get linked to a genuine credential until rpcauth_bindcred()
is called.
The lookup always succeeds, so various places that test if the machine
credential is NULL, are pointless.
As a step towards getting rid of generic credentials, this patch gets
rid of generic machine credentials. The nfs_client and rpc_client
just hold a pointer to a constant principal name.
When a machine credential is wanted, a special static 'struct rpc_cred'
pointer is used. rpcauth_bindcred() recognizes this, finds the
principal from the client, and binds the correct credential.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The cred is a machine_cred iff ->principal is set, so there is no
need for the extra flag.
There is one case which deserves some
explanation. nfs4_root_machine_cred() calls rpc_lookup_machine_cred()
with a NULL principal name which results in not getting a machine
credential, but getting a root credential instead.
This appears to be what is expected of the caller, and is
clearly the result provided by both auth_unix and auth_gss
which already ignore the flag.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
We can use cred->groupinfo (from the 'struct cred') instead.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The SUNRPC credential framework was put together before
Linux has 'struct cred'. Now that we have it, it makes sense to
use it.
This first step just includes a suitable 'struct cred *' pointer
in every 'struct auth_cred' and almost every 'struct rpc_cred'.
The rpc_cred used for auth_null has a NULL 'struct cred *' as nothing
else really makes sense.
For rpc_cred, the pointer is reference counted.
For auth_cred it isn't. struct auth_cred are either allocated on
the stack, in which case the thread owns a reference to the auth,
or are part of 'struct generic_cred' in which case gc_base owns the
reference, and "acred" shares it.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If we want /proc/sys/sunrpc the current kernel also drags in other debug
features which we don't really want. Instead, we should always show the
following entries:
/proc/sys/sunrpc/udp_slot_table_entries
/proc/sys/sunrpc/tcp_slot_table_entries
/proc/sys/sunrpc/tcp_max_slot_table_entries
/proc/sys/sunrpc/min_resvport
/proc/sys/sunrpc/max_resvport
/proc/sys/sunrpc/tcp_fin_timeout
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Thomas Preston <thomas.preston@codethink.co.uk>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
per comment from Leon in rdma mailing list
https://lkml.org/lkml/2018/10/31/312 :
Please don't forget to remove user triggered WARN_ON.
https://lwn.net/Articles/769365/
"Greg Kroah-Hartman raised the problem of core kernel API code that will
use WARN_ON_ONCE() to complain about bad usage; that will not generate
the desired result if WARN_ON_ONCE() is configured to crash the machine.
He was told that the code should just call pr_warn() instead, and that
the called function should return an error in such situations. It was
generally agreed that any WARN_ON() or WARN_ON_ONCE() calls that can be
triggered from user space need to be fixed."
in addition harden rds_sendmsg to detect and overcome issues with
invalid sg count and fail the sendmsg.
Suggested-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: shamir rabinovitch <shamir.rabinovitch@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2018-12-19
Here's the main bluetooth-next pull request for 4.21:
- Multiple fixes & improvements for Broadcom-based controllers
- New USB ID for an Intel controller
- Support for new Broadcom controller variants
- Use DEFINE_SHOW_ATTRIBUTE to simplify debugfs code
- Eliminate confusing "last event is not cmd complete" warning message
- Added vendor suspend/resume support for H:5 (3-Wire UART) controllers
- Various other smaller improvements & fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
-----BEGIN PGP SIGNATURE-----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=EpyK
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have too many changes to list, highlights:
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix a memory leak in an error path
* fix TXQs in interface teardown
* free fraglist if we used it internally
before returning SKB
-----BEGIN PGP SIGNATURE-----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=X7vr
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just three fixes:
* fix a memory leak in an error path
* fix TXQs in interface teardown
* free fraglist if we used it internally
before returning SKB
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a command which completes in Command Status was sent using the
hci_cmd_send-family of APIs there would be a misleading error in the
hci_get_cmd_complete function, since the code would be trying to fetch
the Command Complete parameters when there are none.
Avoid the misleading error and silently bail out from the function in
case the received event is a command status.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
gcc warn this:
net/ipv6/xfrm6_tunnel.c:143 __xfrm6_tunnel_alloc_spi() warn:
always true condition '(spi <= 4294967295) => (0-u32max <= u32max)'
'spi' is u32, which always not greater than XFRM6_TUNNEL_SPI_MAX
because of wrap around. So the second forloop will never reach.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Fixes gcc '-Wunused-but-set-variable' warning:
net/xfrm/xfrm_policy.c: In function 'xfrm_policy_lookup_bytype':
net/xfrm/xfrm_policy.c:2079:6: warning:
variable 'priority' set but not used [-Wunused-but-set-variable]
It not used since commit 6be3b0db6d ("xfrm: policy: add inexact policy
search tree infrastructure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
The radiotap vendor data might be placed after some other
radiotap elements, and thus when accessing it, need to access
the correct offset in the skb data. Fix the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix two bugs in ieee80211_get_vht_max_nss():
* the spec says we should round down
(reported by Nissim)
* there's a double condition, the first one is wrong,
supp_width == 0 / ext_nss_bw == 2 is valid in 80+80
(found by smatch)
Fixes: b0aa75f0b1 ("ieee80211: add new VHT capability fields/parsing")
Reported-by: Nissim Bendanan <nissimx.bendanan@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 uses the frag list to build AMSDU. When freeing
the skb, it may not be really freed, since someone is still
holding a reference to it.
In that case, when TCP skb is being retransmitted, the
pointer to the frag list is being reused, while the data
in there is no longer valid.
Since we will never get frag list from the network stack,
as mac80211 doesn't advertise the capability, we can safely
free and nullify it before releasing the SKB.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If validate_pae_over_nl80211() were to fail in nl80211_crypto_settings(),
we might leak the 'connkeys' allocation. Fix this.
Fixes: 64bf3d4bc2 ("nl80211: Add CONTROL_PORT_OVER_NL80211 attribute")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the alignment handling, it actually matters where in the code
we add the 4 bytes for the presence bitmap to the length; the first
field is the timestamp with 8 byte alignment so we need to add the
space for the extra vendor namespace presence bitmap *before* we do
any alignment for the fields.
Move the presence bitmap length accounting to the right place to fix
the alignment for the data properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
clcsock can be released while kernel_accept() references it in TCP
listen worker. Also, clcsock needs to wake up before released if TCP
fallback is used and the clcsock is blocked by accept. Add a lock to
safely release clcsock and call kernel_sock_shutdown() to wake up
clcsock from accept in smc_release().
Reported-by: syzbot+0bf2e01269f1274b4b03@syzkaller.appspotmail.com
Reported-by: syzbot+e3132895630f957306bc@syzkaller.appspotmail.com
Signed-off-by: Myungho Jung <mhjungk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAME_DISTRIBUTOR messages are transmitted through unicast link on TIPC
2.0, by contrast, the messages are delivered through broadcast link on
TIPC 1.7. But at present, NAME_DISTRIBUTOR messages received by
broadcast link cannot be handled in tipc_rcv() until an unicast message
arrives, which may lead to a significant delay to update name table.
To avoid this delay, we will also deal with broadcast NAME_DISTRIBUTOR
message on broadcast receive path.
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
function br_multicast_toggle now always return 0,
so the variable 'err' is unneeded.
Also cleanup dead branch in br_changelink.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 143ece654f ("tipc: check tsk->group in tipc_wait_for_cond()")
we have to reload grp->dests too after we re-take the sock lock.
This means we need to move the dsts check after tipc_wait_for_cond()
too.
Fixes: 75da2163db ("tipc: introduce communication groups")
Reported-and-tested-by: syzbot+99f20222fc5018d2b97a@syzkaller.appspotmail.com
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to clean up an indentation issue
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds metadata to sk_msg_md for BPF programs to read the sk_msg
size.
When the SK_MSG program is running under an application that is using
sendfile the data is not copied into sk_msg buffers by default. Rather
the BPF program uses sk_msg_pull_data to read the bytes in. This
avoids doing the costly memcopy instructions when they are not in
fact needed. However, if we don't know the size of the sk_msg we
have to guess if needed bytes are available by doing a pull request
which may fail. By including the size of the sk_msg BPF programs can
check the size before issuing sk_msg_pull_data requests.
Additionally, the same applies for sendmsg calls when the application
provides multiple iovs. Here the BPF program needs to pull in data
to update data pointers but its not clear where the data ends without
a size parameter. In many cases "guessing" is not easy to do
and results in multiple calls to pull and without bounded loops
everything gets fairly tricky.
Clean this up by including a u32 size field. Note, all writes into
sk_msg_md are rejected already from sk_msg_is_valid_access so nothing
additional is needed there.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
If a server side socket is bound to an address, but not in the listening
state yet, incoming connection requests should receive a reset control
packet in response. However, the function used to send the reset
silently drops the reset packet if the sending socket isn't bound
to a remote address (as is the case for a bound socket not yet in
the listening state). This change fixes this by using the src
of the incoming packet as destination for the reset packet in
this case.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Reviewed-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2018-12-18
1) Fix error return code in xfrm_output_one()
when no dst_entry is attached to the skb.
From Wei Yongjun.
2) The xfrm state hash bucket count reported to
userspace is off by one. Fix from Benjamin Poirier.
3) Fix NULL pointer dereference in xfrm_input when
skb_dst_force clears the dst_entry.
4) Fix freeing of xfrm states on acquire. We use a
dedicated slab cache for the xfrm states now,
so free it properly with kmem_cache_free.
From Mathias Krause.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-12-18
1) Add xfrm policy selftest scripts.
From Florian Westphal.
2) Split inexact policies into four different search list
classes and use the rbtree infrastructure to store/lookup
the policies. This is to improve the policy lookup
performance after the flowcache removal.
Patches from Florian Westphal.
3) Various coding style fixes, from Colin Ian King.
4) Fix policy lookup logic after adding the inexact policy
search tree infrastructure. From Florian Westphal.
5) Remove a useless remove BUG_ON from xfrm6_dst_ifdown.
From Li RongQing.
6) Use the correct policy direction for lookups on hash
rebuilding. From Florian Westphal.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Over the years, xprt_connect_status() has been superseded by
call_connect_status(), which now handles all the errors that
xprt_connect_status() does and more. Since the latter converts
all errors that it doesn't recognise to EIO, then it is time
for it to be retired.
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Ensure that we clear XPRT_CONNECTING before releasing the XPRT_LOCK so that
we don't have races between the (asynchronous) socket setup code and
tasks in xprt_connect().
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
When the socket is closed, we need to call xprt_disconnect_done() in order
to clean up the XPRT_WRITE_SPACE flag, and wake up the sleeping tasks.
However, we also want to ensure that we don't wake them up before the socket
is closed, since that would cause thundering herd issues with everyone
piling up to retransmit before the TCP shutdown dance has completed.
Only the task that holds XPRT_LOCKED needs to wake up early in order to
allow the close to complete.
Reported-by: Dave Wysochanski <dwysocha@redhat.com>
Reported-by: Scott Mayhew <smayhew@redhat.com>
Cc: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
recvmmsg() takes two arguments to pointers of structures that differ
between 32-bit and 64-bit architectures: mmsghdr and timespec.
For y2038 compatbility, we are changing the native system call from
timespec to __kernel_timespec with a 64-bit time_t (in another patch),
and use the existing compat system call on both 32-bit and 64-bit
architectures for compatibility with traditional 32-bit user space.
As we now have two variants of recvmmsg() for 32-bit tasks that are both
different from the variant that we use on 64-bit tasks, this means we
also require two compat system calls!
The solution I picked is to flip things around: The existing
compat_sys_recvmmsg() call gets moved from net/compat.c into net/socket.c
and now handles the case for old user space on all architectures that
have set CONFIG_COMPAT_32BIT_TIME. A new compat_sys_recvmmsg_time64()
call gets added in the old place for 64-bit architectures only, this
one handles the case of a compat mmsghdr structure combined with
__kernel_timespec.
In the indirect sys_socketcall(), we now need to call either
do_sys_recvmmsg() or __compat_sys_recvmmsg(), depending on what kind of
architecture we are on. For compat_sys_socketcall(), no such change is
needed, we always call __compat_sys_recvmmsg().
I decided to not add a new SYS_RECVMMSG_TIME64 socketcall: Any libc
implementation for 64-bit time_t will need significant changes including
an updated asm/unistd.h, and it seems better to consistently use the
separate syscalls that configuration, leaving the socketcall only for
backward compatibility with 32-bit time_t based libc.
The naming is asymmetric for the moment, so both existing syscalls
entry points keep their names, while the new ones are recvmmsg_time32
and compat_recvmmsg_time64 respectively. I expect that we will rename
the compat syscalls later as we start using generated syscall tables
everywhere and add these entry points.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When disabling HE due to the lack of HT/VHT, do it
at an earlier stage to avoid advertising HE capabilities IE.
Also, at this point, no need to check if AP supports HE, since
it is already checked earlier (in ieee80211_prep_channel).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Up until now, the IEEE80211_STA_DISABLE_HE flag was set only based
on whether the AP has advertised HE capabilities.
This flag should be set also if STA does not support HE
(regardless of the AP support).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Similar to WMM IE, if MU_EDCA IE parameters changed (or ceased to exist)
tell the Driver about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TWT is a feature that was added in 11ah and enhanced in
11ax. There are two bits that need to be set if we want
to use the feature in 11ax: one in the HE Capability IE
and one in the Extended Capability IE. This is because
of backward compatibility between 11ah and 11ax.
In order to simplify the flow for the low level driver
in managed mode, aggregate the two bits and add a boolean
that tells whether TWT is supported or not, but only if
11ax is supported.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently radar detection and corresponding channel switch is handled
at the AP device. STA ignores these detected radar events since the
radar signal can be seen mostly by the AP as well. But in scenarios where
a radar signal is seen only at STA, notifying this event to the AP which
can trigger a channel switch can be useful.
Stations can report such radar events autonomously through Spectrum
management (Measurement Report) action frame to its AP. The userspace on
processing the report can notify the kernel with the use of the added
NL80211_CMD_NOTIFY_RADAR to indicate the detected event and inturn adding
the reported channel to NOL.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we build AMSDU from GSO packets, it can lead to
bad results if anyone tries to call skb_gso_segment
on the packets.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At the place where this code lives now, the skb can never be
NULL, so we can remove the pointless NULL check.
It seems to exist because this code was moved around a few times
and originally came from a place where it could in fact be NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This isn't really a problem now, but it means that the function
has a few NULL checks that are only relevant when coming from
the initial interface added in mac80211, and that's confusing.
Just pass non-NULL (but equivalently empty) in that case and
remove all the NULL checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The monitor interface Rx handling of SKBs that contain only
radiotap information was buggy as it tried to access the
SKB assuming it contains a frame.
To fix this, check the RX_FLAG_NO_PSDU flag in the Rx status
(indicting that the SKB contains only radiotap information),
and do not perform data path specific processing when the flag
is set.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are talks about enabling -Wimplicit-fallthrough warnings in the
mainline and it is already enabled in linux-next. Add all the
missing annotations to prevent warnings when this happens.
And in one case, remove the extra text from the annotation so that the
compiler recognizes it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pointer and corresponding length is always set in pairs
in cfg80211, so no need to have this strange defensive check
that also confuses static checkers. Clean it up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The legacy <linux/gpio.h> header is no longer in use by the
rfkill driver, so drop this include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recently TXQ teardown was moved earlier in ieee80211_unregister_hw(),
to avoid a use-after-free of the netdev data. However, interfaces
aren't fully removed at the point, and cfg80211_shutdown_all_interfaces
can for example, TX a deauth frame. Move the TXQ teardown to the
point between cfg80211_shutdown_all_interfaces and the free of
netdev queues, so we can be sure they are torn down before netdev
is freed, but after there is no ongoing TX.
Fixes: 77cfaf52ec ("mac80211: Run TXQ teardown code before de-registering interfaces")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mfc6_cache is not needed by ip6mr_forward2 so drop it from the input
argument list.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mfc_cache is not needed by ipmr_queue_xmit so drop it from the input
argument list.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SOF_TIMESTAMPING_OPT_ID is supported on TCP, UDP and RAW sockets.
But it was missing on RAW with IPPROTO_IP, PF_PACKET and CAN.
Add skb_setup_tx_timestamp that configures both tx_flags and tskey
for these paths that do not need corking or use bytestream keys.
Fixes: 09c2d251b7 ("net-timestamp: add key to disambiguate concurrent datagrams")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raw sockets support tx timestamping, but one case is missing.
IPPROTO_RAW takes a separate packet construction path. raw_send_hdrinc
has an explicit call to sock_tx_timestamp, but rawv6_send_hdrinc does
not. Add it.
Fixes: 11878b40ed ("net-timestamp: SOCK_RAW and PING timestamping")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d9fbc7f643 "net: tcp: prefer listeners bound to an address"
removes port-only listener lookups. This caused segfaults in DCCP
lookups because DCCP did not initialize the (addr,port) hashtable.
This patch adds said initialization.
The only non-trivial issue here is the size of the new hashtable.
It seemed reasonable to make it match the size of the port-only
hashtable (= INET_LHTABLE_SIZE) that was used previously. Other
parameters to inet_hashinfo2_init() match those used in TCP.
V2 changes: marked inet_hashinfo2_init as an exported symbol
so that DCCP compiles when configured as a module.
Tested: syzcaller issues fixed; the second patch in the patchset
tests that DCCP lookups work correctly.
Fixes: d9fbc7f643 "net: tcp: prefer listeners bound to an address"
Reported-by: syzcaller <syzkaller@googlegroups.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handling exceptions for direct UDP encapsulation in GUE (that is,
UDP-in-UDP) leads to unbounded recursion in the GUE exception handler,
syzbot reported.
While draft-ietf-intarea-gue-06 doesn't explicitly forbid direct
encapsulation of UDP in GUE, it probably doesn't make sense to set up GUE
this way, and it's currently not even possible to configure this.
Skip exception handling if the GUE proto/ctype field is set to the UDP
protocol number. Should we need to handle exceptions for UDP-in-GUE one
day, we might need to either explicitly set a bound for recursion, or
implement a special iterative handling for these cases.
Reported-and-tested-by: syzbot+43f6755d1c2e62743468@syzkaller.appspotmail.com
Fixes: b8a51b38e4 ("fou, fou6: ICMP error handlers for FoU and GUE")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If same destination IP address config is already existing, that config is
just used. MAC address also should be same.
However, there is no MAC address checking routine.
So that MAC address checking routine is added.
test commands:
%iptables -A INPUT -p tcp -i lo -d 192.168.0.5 --dport 80 \
-j CLUSTERIP --new --hashmode sourceip \
--clustermac 01:00:5e:00:00:20 --total-nodes 2 --local-node 1
%iptables -A INPUT -p tcp -i lo -d 192.168.0.5 --dport 80 \
-j CLUSTERIP --new --hashmode sourceip \
--clustermac 01:00:5e:00:00:21 --total-nodes 2 --local-node 1
After this patch, above commands are disallowed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If just a table name was given, nf_tables_dump_rules() continued over
the list of tables even after a match was found. The simple fix is to
exit the loop if it reached the bottom and ctx->table was not NULL.
When iterating over the table's chains, the same problem as above
existed. But worse than that, if a chain name was given the hash table
wasn't used to find the corresponding chain. Fix this by introducing a
helper function iterating over a chain's rules (and taking care of the
cb->args handling), then introduce a shortcut to it if a chain name was
given.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Each media stream negotiation between 2 SIP peers will trigger creation
of 4 different expectations (2 RTP and 2 RTCP):
- INVITE will create expectations for the media packets sent by the
called peer
- reply to the INVITE will create expectations for media packets sent
by the caller
The dport used by these expectations usually match the ones selected
by the SIP peers, but they might get translated due to conflicts with
another expectation. When such event occur, it is important to do
this translation in both directions, dport translation on the receiving
path and sport translation on the sending path.
This commit fixes the sport translation when the peer requiring it is
also the one that starts the media stream. In this scenario, first media
stream packet is forwarded from LAN to WAN and will rely on
nf_nat_sip_expected() to do the necessary sport translation. However, the
expectation matched by this packet does not contain the necessary information
for doing SNAT, this data being stored in the paired expectation created by
the sender's SIP message (INVITE or reply to it).
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This removes the (now empty) nf_nat_l4proto struct, all its instances
and all the no longer needed runtime (un)register functionality.
nf_nat_need_gre() can be axed as well: the module that calls it (to
load the no-longer-existing nat_gre module) also calls other nat core
functions. GRE nat is now always available if kernel is built with it.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This removes the last l4proto indirection, the two callers, the l3proto
packet mangling helpers for ipv4 and ipv6, now call the
nf_nat_l4proto_manip_pkt() helper.
nf_nat_proto_{dccp,tcp,sctp,gre,icmp,icmpv6} are left behind, even though
they contain no functionality anymore to not clutter this patch.
Next patch will remove the empty files and the nf_nat_l4proto
struct.
nf_nat_proto_udp.c is renamed to nf_nat_proto.c, as it now contains the
other nat manip functionality as well, not just udp and udplite.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
all protocols did set this to nf_nat_l4proto_nlattr_to_range, so
just call it directly.
The important difference is that we'll now also call it for
protocols that we don't support (i.e., nf_nat_proto_unknown did
not provide .nlattr_to_range).
However, there should be no harm, even icmp provided this callback.
If we don't implement a specific l4nat for this, nothing would make
use of this information, so adding a big switch/case construct listing
all supported l4protocols seems a bit pointless.
This change leaves a single function pointer in the l4proto struct.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
With exception of icmp, all of the l4 nat protocols set this to
nf_nat_l4proto_in_range.
Get rid of this and just check the l4proto in the caller.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
No need for indirections here, we only support ipv4 and ipv6
and the called functions are very small.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
fold remaining users (icmp, icmpv6, gre) into nf_nat_l4proto_unique_tuple.
The static-save of old incarnation of resolved key in gre and icmp is
removed as well, just use the prandom based offset like the others.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
almost all l4proto->unique_tuple implementations just call this helper,
so make ->unique_tuple() optional and call its helper directly if the
l4proto doesn't override it.
This is an intermediate step to get rid of ->unique_tuple completely.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Historically this was net_random() based, and was then converted to
a hash based algorithm (private boot seed + hash of endpoint addresses)
due to concerns of leaking net_random() bits.
RANDOM_FULLY mode was added later to avoid problems with hash
based mode (see commit 34ce324019,
"netfilter: nf_nat: add full port randomization support" for details).
Just make prandom_u32() the default search starting point and get rid of
->secure_port() altogether.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In case almost or all available ports are taken, clash resolution can
take a very long time, resulting in soft lockup.
This can happen when many to-be-natted hosts connect to same
destination:port (e.g. a proxy) and all connections pass the same SNAT.
Pick a random offset in the acceptable range, then try ever smaller
number of adjacent port numbers, until either the limit is reached or a
useable port was found. This results in at most 248 attempts
(128 + 64 + 32 + 16 + 8, i.e. 4 restarts with new search offset)
instead of 64000+,
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since a pseudo-random starting point is used in finding a port in
the default case, that 'else if' branch above is no longer a necessity.
So remove it to simplify code.
Signed-off-by: Xiaozhou Liu <liuxiaozhou@bytedance.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch implements ndo_fdb_get for the bridge
fdb.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for fdb get similar to
route get. arguments can be any of the following (similar to fdb add/del/dump):
[bridge, mac, vlan] or
[bridge_port, mac, vlan, flags=[NTF_MASTER]] or
[dev, mac, [vni|vlan], flags=[NTF_SELF]]
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the destination address is link local, add override bit into the
switch tag to let such a packet through the switch even if the port is
blocked.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out common code from the tag_ksz , so that the code can be used
with other KSZ family switches which use differenly sized tags.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ec49d83f24.
Cause build failures when DCCP is modular.
ERROR: "inet_hashinfo2_init" [net/dccp/dccp.ko] undefined!
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to routes and rules, add protocol attribute to neighbor entries
for easier tracking of how each was created.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d9fbc7f643 "net: tcp: prefer listeners bound to an address"
removes port-only listener lookups. This caused segfaults in DCCP
lookups because DCCP did not initialize the (addr,port) hashtable.
This patch adds said initialization.
The only non-trivial issue here is the size of the new hashtable.
It seemed reasonable to make it match the size of the port-only
hashtable (= INET_LHTABLE_SIZE) that was used previously. Other
parameters to inet_hashinfo2_init() match those used in TCP.
Tested: syzcaller issues fixed; the second patch in the patchset
tests that DCCP lookups work correctly.
Fixes: d9fbc7f643 "net: tcp: prefer listeners bound to an address"
Reported-by: syzcaller <syzkaller@googlegroups.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Protocol Field Compression (PFC) is enabled, the "Protocol" field
in PPP packet will be received without leading 0x00. See section 6.5 in
RFC 1661 for details. So let's decompress protocol field if needed, the
same way it's done in drivers/net/ppp/pptp.c.
In case when "nopcomp" pppd option is not enabled, PFC (pcomp) can be
negotiated during LCP handshake, and L2TP driver in kernel will receive
PPP packets with compressed Protocol field, which in turn leads to next
error:
Protocol Rejected (unsupported protocol 0x2145)
because instead of Protocol=0x0021 in PPP packet there will be
Protocol=0x21. This patch unwraps it back to 0x0021, which fixes the
issue.
Sending the compressed Protocol field will be implemented in subsequent
patch, this one is self-sufficient.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergey reported that forwarding was no longer working
if fq packet scheduler was used.
This is caused by the recent switch to EDT model, since incoming
packets might have been timestamped by __net_timestamp()
__net_timestamp() uses ktime_get_real(), while fq expects packets
using CLOCK_MONOTONIC base.
The fix is to clear skb->tstamp in forwarding paths.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sergey Matyukevich <geomatsi@gmail.com>
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids another indirect call for UDP GRO. Again, the test
for the IPv6 variant is performed first.
v1 -> v2:
- adapted to INDIRECT_CALL_ changes
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids an indirect call in the receive path for TCP and UDP
packets. TCP takes precedence on UDP, so that we have a single
additional conditional in the common case.
When IPV6 is build as module, all gro symbols except UDPv6 are
builtin, while the latter belong to the ipv6 module, so we
need some special care.
v1 -> v2:
- adapted to INDIRECT_CALL_ changes
v2 -> v3:
- fix build issue with CONFIG_IPV6=m
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids an indirect calls for L3 GRO receive path, both
for ipv4 and ipv6, if the latter is not compiled as a module.
Note that when IPv6 is compiled as builtin, it will be checked first,
so we have a single additional compare for the more common path.
v1 -> v2:
- adapted to INDIRECT_CALL_ changes
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 7969e5c40d ("ip: discard IPv4 datagrams with overlapping
segments.") IPv4 reassembly code drops the whole queue whenever an
overlapping fragment is received. However, the test is written in a way
which detects duplicate fragments as overlapping so that in environments
with many duplicate packets, fragmented packets may be undeliverable.
Add an extra test and for (potentially) duplicate fragment, only drop the
new fragment rather than the whole queue. Only starting offset and length
are checked, not the contents of the fragments as that would be too
expensive. For similar reason, linear list ("run") of a rbtree node is not
iterated, we only check if the new fragment is a subset of the interval
covered by existing consecutive fragments.
v2: instead of an exact check iterating through linear list of an rbtree
node, only check if the new fragment is subset of the "run" (suggested
by Eric Dumazet)
Fixes: 7969e5c40d ("ip: discard IPv4 datagrams with overlapping segments.")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for returning, the var leaf is not
used in the qdisc_leaf(). For simplicity, remove it.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit allows sockets bound to a VRF to receive ipv6 link local
packets. However, it only works for UDP and worse TCP connection attempts
to the LLA with the only listener bound to the VRF just hang where as
before the client gets a reset and connection refused. Fix by adjusting
ir_iif for LL addresses and packets received through a device enslaved
to a VRF.
Fixes: 6f12fa7755 ("vrf: mark skb for multicast or link-local as enslaved to VRF")
Reported-by: Donald Sharp <sharpd@cumulusnetworks.com>
Cc: Mike Manning <mmanning@vyatta.att-mail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2018-12-15
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix liveness propagation of callee saved registers, from Jakub.
2) fix overflow in bpf_jit_limit knob, from Daniel.
3) bpf_flow_dissector api fix, from Stanislav.
4) bpf_perf_event api fix on powerpc, from Sandipan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A relatively common use case is to have several IPs configured
on a host, and have different listeners for each of them. We would
like to add a "catch all" listener on addr_any, to match incoming
connections not served by any of the listeners bound to a specific
address.
However, port-only lookups can match addr_any sockets when sockets
listening on specific addresses are present if so_reuseport flag
is set. This patch eliminates lookups into port-only hashtable,
as lookups by (addr,port) tuple are easily available.
In addition, compute_score() is tweaked to _not_ match
addr_any sockets to specific addresses, as hash collisions
could result in the unwanted behavior described above.
Tested: the patch compiles; full test in the last patch in this
patchset. Existing reuseport_* selftests also pass.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A relatively common use case is to have several IPs configured
on a host, and have different listeners for each of them. We would
like to add a "catch all" listener on addr_any, to match incoming
connections not served by any of the listeners bound to a specific
address.
However, port-only lookups can match addr_any sockets when sockets
listening on specific addresses are present if so_reuseport flag
is set. This patch eliminates lookups into port-only hashtable,
as lookups by (addr,port) tuple are easily available.
In addition, compute_score() is tweaked to _not_ match
addr_any sockets to specific addresses, as hash collisions
could result in the unwanted behavior described above.
Tested: the patch compiles; full test in the last patch in this
patchset. Existing reuseport_* selftests also pass.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A relatively common use case is to have several IPs configured
on a host, and have different listeners for each of them. We would
like to add a "catch all" listener on addr_any, to match incoming
connections not served by any of the listeners bound to a specific
address.
However, port-only lookups can match addr_any sockets when sockets
listening on specific addresses are present if so_reuseport flag
is set. This patch eliminates lookups into port-only hashtable,
as lookups by (addr,port) tuple are easily available.
In addition, compute_score() is tweaked to _not_ match
addr_any sockets to specific addresses, as hash collisions
could result in the unwanted behavior described above.
Tested: the patch compiles; full test in the last patch in this
patchset. Existing reuseport_* selftests also pass.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A relatively common use case is to have several IPs configured
on a host, and have different listeners for each of them. We would
like to add a "catch all" listener on addr_any, to match incoming
connections not served by any of the listeners bound to a specific
address.
However, port-only lookups can match addr_any sockets when sockets
listening on specific addresses are present if so_reuseport flag
is set. This patch eliminates lookups into port-only hashtable,
as lookups by (addr,port) tuple are easily available.
In addition, compute_score() is tweaked to _not_ match
addr_any sockets to specific addresses, as hash collisions
could result in the unwanted behavior described above.
Tested: the patch compiles; full test in the last patch in this
patchset. Existing reuseport_* selftests also pass.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_wait_for_cond() drops socket lock before going to sleep,
but tsk->group could be freed right after that release_sock().
So we have to re-check and reload tsk->group after it wakes up.
After this patch, tipc_wait_for_cond() returns -ERESTARTSYS when
tsk->group is NULL, instead of continuing with the assumption of
a non-NULL tsk->group.
(It looks like 'dsts' should be re-checked and reloaded too, but
it is a different bug.)
Similar for tipc_send_group_unicast() and tipc_send_group_anycast().
Reported-by: syzbot+10a9db47c3a0e13eb31c@syzkaller.appspotmail.com
Fixes: b7d4263551 ("tipc: introduce flow control for group broadcast messages")
Fixes: ee106d7f94 ("tipc: introduce group anycast messaging")
Fixes: 27bd9ec027 ("tipc: introduce group unicast messaging")
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Externally learned entries are similar to PERMANENT entries in the
sense they are managed by userspace and can not be garbage collected.
As such remove them from the gc_list, remove the flags check from
neigh_forced_gc and skip threshold checks in neigh_alloc. As with
PERMANENT entries, this allows unlimited number of NTF_EXT_LEARNED
entries.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
neigh_update_ext_learned has one caller in neighbour.c so does not need
to be defined in the header. Move it and in the process remove the
intialization of ndm_flags and just set it based on the flags check.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
neigh_del now only has 1 caller, and the state and flags arguments
are both 0. Remove them and simplify neigh_del.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PERMANENT entries are not on the gc_list so the state check is now
redundant. Also, the move to not purge entries until after 5 seconds
should not apply to FAILED entries; those can be removed immediately
to make way for newer ones. This restores the previous logic prior to
the gc_list.
Fixes: 58956317c8 ("neighbor: Improve garbage collection")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lock checker noted an inverted lock order between neigh_change_state
(neighbor lock then table lock) and neigh_periodic_work (table lock and
then neighbor lock) resulting in:
[ 121.057652] ======================================================
[ 121.058740] WARNING: possible circular locking dependency detected
[ 121.059861] 4.20.0-rc6+ #43 Not tainted
[ 121.060546] ------------------------------------------------------
[ 121.061630] kworker/0:2/65 is trying to acquire lock:
[ 121.062519] (____ptrval____) (&n->lock){++--}, at: neigh_periodic_work+0x237/0x324
[ 121.063894]
[ 121.063894] but task is already holding lock:
[ 121.064920] (____ptrval____) (&tbl->lock){+.-.}, at: neigh_periodic_work+0x194/0x324
[ 121.066274]
[ 121.066274] which lock already depends on the new lock.
[ 121.066274]
[ 121.067693]
[ 121.067693] the existing dependency chain (in reverse order) is:
...
Fix by renaming neigh_change_state to neigh_update_gc_list, changing
it to only manage whether an entry should be on the gc_list and taking
locks in the same order as neigh_periodic_work. Invoke at the end of
neigh_update only if diff between old or new states has the PERMANENT
flag set.
Fixes: 8cc196d6ef ("neighbor: gc_list changes should be protected by table lock")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While most distributions long ago switched to the iproute2 suite
of utilities, which allow class-e (240.0.0.0/4) address assignment,
distributions relying on busybox, toybox and other forms of
ifconfig cannot assign class-e addresses without this kernel patch.
While CIDR has been obsolete for 2 decades, and a survey of all the
open source code in the world shows the IN_whatever macros are also
obsolete... rather than obsolete CIDR from this ioctl entirely, this
patch merely enables class-e assignment, sanely.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vr.mifi is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/ipv6/ip6mr.c:1845 ip6mr_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
net/ipv6/ip6mr.c:1919 ip6mr_compat_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
Fix this by sanitizing vr.mifi before using it to index mrt->vif_table'
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 69bd48404f ("net/sched: Remove egdev mechanism"),
tc_setup_cb_call() is nearly identical to tcf_block_cb_call(),
so we can just fold tcf_block_cb_call() into tc_setup_cb_call()
and remove its unused parameter 'exts'.
Fixes: 69bd48404f ("net/sched: Remove egdev mechanism")
Cc: Oz Shlomo <ozsh@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old code always starts from fixed port for VMADDR_PORT_ANY. Sometimes
when VMM crashed, there is still orphaned vsock which is waiting for
close timer, then it could cause connection time out for new started VM
if they are trying to connect to same port with same guest cid since the
new packets could hit that orphaned vsock. We could also fix this by doing
more in vhost_vsock_reset_orphans, but any way, it should be better to start
from a random local port instead of a fixed one.
Signed-off-by: Lepton Wu <ytht.net@gmail.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW unhash within mutex for registered tls devices cause sleep
when called from tcp_set_state for TCP_CLOSE. Release lock and
re-acquire after function call with ref count incr/dec.
defined kref and fp release for tls_device to ensure device
is not released outside lock.
BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:748
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/7
INFO: lockdep is turned off.
CPU: 7 PID: 0 Comm: swapper/7 Tainted: G W O
Call Trace:
<IRQ>
dump_stack+0x5e/0x8b
___might_sleep+0x222/0x260
__mutex_lock+0x5c/0xa50
? vprintk_emit+0x1f3/0x440
? kmem_cache_free+0x22d/0x2a0
? tls_hw_unhash+0x2f/0x80
? printk+0x52/0x6e
? tls_hw_unhash+0x2f/0x80
tls_hw_unhash+0x2f/0x80
tcp_set_state+0x5f/0x180
tcp_done+0x2e/0xe0
tcp_rcv_state_process+0x92c/0xdd3
? lock_acquire+0xf5/0x1f0
? tcp_v4_rcv+0xa7c/0xbe0
? tcp_v4_do_rcv+0x70/0x1e0
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
create_ctx is called from tls_init and tls_hw_prot
hence initialize function pointers in common routine.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TIPC_NLA_UDP_REMOTE is an IPv6 mcast address but
TIPC_NLA_UDP_LOCAL is an IPv4 address, a NULL-ptr deref is triggered
as the UDP tunnel sock is initialized to IPv4 or IPv6 sock merely
based on the protocol in local address.
We should just error out when the remote address and local address
have different protocols.
Reported-by: syzbot+eb4da3a20fad2e52555d@syzkaller.appspotmail.com
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_udp_xmit() drops the packet on error, there is no
need to drop it again.
Fixes: ef20cd4dd1 ("tipc: introduce UDP replicast")
Reported-and-tested-by: syzbot+eae585ba2cc2752d3704@syzkaller.appspotmail.com
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lock_sock() must be used in process context to be race-free with
other lock_sock() callers, for example, tipc_release(). Otherwise
using the spinlock directly can't serialize a parallel tipc_release().
As it is blocking, we have to hold the sock refcnt before
rhashtable_walk_stop() and release it after rhashtable_walk_start().
Fixes: 07f6c4bc04 ("tipc: convert tipc reference table to use generic rhashtable")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETLINK_DUMP_STRICT_CHK can be used for all GET requests,
dumps as well as doit handlers. Replace the DUMP in the
name with GET make that clearer.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port device seeks approval of a potential new MAC address, make
sure that should the bridge device end up using this address, all
interested parties would agree with it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is attached to a bridge, the address of the bridge in
question may change as well. Even if it would not change at this
point (because the current bridge address is lower), it might end up
changing later as a result of detach of another port, which can't be
vetoed.
Therefore issue NETDEV_PRE_CHANGEADDR regardless of whether the address
will be used at this point or not, and make sure all involved parties
would agree with the change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a device address is about to be changed, or an address added to the
list of device HW addresses, it is necessary to ensure that all
interested parties can support the address. Therefore, send the
NETDEV_PRE_CHANGEADDR notification, and if anyone bails on it, do not
change the address.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETDEV_CHANGEADDR notification is emitted after a device address
changes. Extending this message to allow vetoing is certainly possible,
but several other notification types have instead adopted a simple
two-stage approach: first a "pre" notification is sent to make sure all
interested parties are OK with a change that's about to be done. Then
the change is done, and afterwards a "post" notification is sent.
This dual approach is easier to use: when the change is vetoed, nothing
has changed yet, and it's therefore unnecessary to roll anything back.
Therefore adopt it for NETDEV_CHANGEADDR as well.
To that end, add NETDEV_PRE_CHANGEADDR and an info structure to go along
with it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will add a notifier type NETDEV_PRE_CHANGEADDR, which
allows vetoing of MAC address changes. One prominent path to that
notification is through dev_set_mac_address(). Therefore give this
function an extack argument, so that it can be packed together with the
notification. Thus a textual reason for rejection (or a warning) can be
communicated back to the user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make overflows as obvious as possible and to prevent code from blithely
proceeding with a truncated string. This also has a side-effect to fix a
compilation warning when using GCC 8.2.1.
net/netfilter/ipset/ip_set_core.c: In function 'ip_set_sockfn_get':
net/netfilter/ipset/ip_set_core.c:2027:3: warning: 'strncpy' writing 32 bytes into a region of size 2 overflows the destination [-Wstringop-overflow=]
Signed-off-by: Qian Cai <cai@gmx.us>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
New function added by "Introduction of new commands and protocol
version 7" is not working, since we return skb2 to user
Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr>
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Introduce a helper to copy datagram into an iovec iterator
but also update a predefined hash. This is useful for
consumers of skb_copy_datagram_iter to also support inflight
data digest without having to finish to copy and only then
traverse the iovec and calculate the digest hash.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sagi Grimberg <sagi@lightbitslabs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
skb_copy_datagram_iter and skb_copy_and_csum_datagram are essentialy
the same but with a couple of differences: The first is the copy
operation used which either a simple copy or a csum_and_copy, and the
second are the behavior on the "short copy" path where simply copy
needs to return the number of bytes successfully copied while csum_and_copy
needs to fault immediately as the checksum is partial.
Introduce __skb_datagram_iter that additionally accepts:
1. copy operation function pointer
2. private data that goes with the copy operation
3. fault_short flag to indicate the action on short copy
Suggested-by: David S. Miller <davem@davemloft.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sagi Grimberg <sagi@lightbitslabs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This will be useful to consolidate skb_copy_and_hash_datagram_iter and
skb_copy_and_csum_datagram to a single code path.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sagi Grimberg <sagi@lightbitslabs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Fix warnings suspicious rcu usage when handling base chain
statistics, from Taehee Yoo.
2) Refetch pointer to tcp header from nf_ct_sack_adjust() since
skb_make_writable() may reallocate data area, reported by Google
folks patch from Florian.
3) Incorrect netlink nest end after previous cancellation from error
path in ipset, from Pan Bian.
4) Use dst_hold_safe() from nf_xfrm_me_harder(), from Florian.
5) Use rb_link_node_rcu() for rcu-protected rbtree node in
nf_conncount, from Taehee Yoo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers use switchdev_handle_port_obj_add() to handle recursive descent
through lower devices. Change this function prototype to take add_cb
that itself takes an extack argument. Decode extack from
switchdev_notifier_port_obj_info and pass it to add_cb.
Update mlxsw and ocelot drivers which use this helper.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass extack to the drivers that need it, add an extack field
to struct switchdev_notifier_info, and an extack argument to the
function call_switchdev_blocking_notifiers(). Also add a helper function
switchdev_notifier_info_to_extack().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, bridge driver has extack argument available to
pass to switchdev. Therefore extend switchdev_port_obj_add() with this
argument, updating all callers, and passing the argument through to
switchdev_port_obj_notify().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_bridge_setlink has been updated in the previous patch to have extack
available, and changelink RTNL op has had this argument since the time
extack was added. Propagate both through the bridge driver to eventually
reach br_switchdev_port_vlan_add(), where it will be used by subsequent
patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to implement a VLAN addition or reconfiguration.
In those cases it's desirable to explain to the user that it was
rejected (and why).
To that end, add extack argument to ndo_bridge_setlink. Adapt all users
to that change.
Following patches will use the new argument in the bridge driver.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rbnode in insert_tree() is rcu protected pointer.
So, in order to handle this pointer, _rcu function should be used.
rb_link_node_rcu() is a rcu version of rb_link_node().
Fixes: 34848d5c89 ("netfilter: nf_conncount: Split insert and traversal")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In the error handling block, nla_nest_cancel(skb, atd) is called to
cancel the nest operation. But then, ipset_nest_end(skb, atd) is
unexpected called to end the nest operation. This patch calls the
ipset_nest_end only on the branch that nla_nest_cancel is not called.
Fixes: 45040978c8 ("netfilter: ipset: Fix set:list type crash when flush/dump set in parallel")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Make all the required change to start use the ib_device_ops structure.
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Michael and Sandipan report:
Commit ede95a63b5 introduced a bpf_jit_limit tuneable to limit BPF
JIT allocations. At compile time it defaults to PAGE_SIZE * 40000,
and is adjusted again at init time if MODULES_VADDR is defined.
For ppc64 kernels, MODULES_VADDR isn't defined, so we're stuck with
the compile-time default at boot-time, which is 0x9c400000 when
using 64K page size. This overflows the signed 32-bit bpf_jit_limit
value:
root@ubuntu:/tmp# cat /proc/sys/net/core/bpf_jit_limit
-1673527296
and can cause various unexpected failures throughout the network
stack. In one case `strace dhclient eth0` reported:
setsockopt(5, SOL_SOCKET, SO_ATTACH_FILTER, {len=11, filter=0x105dd27f8},
16) = -1 ENOTSUPP (Unknown error 524)
and similar failures can be seen with tools like tcpdump. This doesn't
always reproduce however, and I'm not sure why. The more consistent
failure I've seen is an Ubuntu 18.04 KVM guest booted on a POWER9
host would time out on systemd/netplan configuring a virtio-net NIC
with no noticeable errors in the logs.
Given this and also given that in near future some architectures like
arm64 will have a custom area for BPF JIT image allocations we should
get rid of the BPF_JIT_LIMIT_DEFAULT fallback / default entirely. For
4.21, we have an overridable bpf_jit_alloc_exec(), bpf_jit_free_exec()
so therefore add another overridable bpf_jit_alloc_exec_limit() helper
function which returns the possible size of the memory area for deriving
the default heuristic in bpf_jit_charge_init().
Like bpf_jit_alloc_exec() and bpf_jit_free_exec(), the new
bpf_jit_alloc_exec_limit() assumes that module_alloc() is the default
JIT memory provider, and therefore in case archs implement their custom
module_alloc() we use MODULES_{END,_VADDR} for limits and otherwise for
vmalloc_exec() cases like on ppc64 we use VMALLOC_{END,_START}.
Additionally, for archs supporting large page sizes, we should change
the sysctl to be handled as long to not run into sysctl restrictions
in future.
Fixes: ede95a63b5 ("bpf: add bpf_jit_limit knob to restrict unpriv allocations")
Reported-by: Sandipan Das <sandipan@linux.ibm.com>
Reported-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-12-11
The following pull-request contains BPF updates for your *net-next* tree.
It has three minor merge conflicts, resolutions:
1) tools/testing/selftests/bpf/test_verifier.c
Take first chunk with alignment_prevented_execution.
2) net/core/filter.c
[...]
case bpf_ctx_range_ptr(struct __sk_buff, flow_keys):
case bpf_ctx_range(struct __sk_buff, wire_len):
return false;
[...]
3) include/uapi/linux/bpf.h
Take the second chunk for the two cases each.
The main changes are:
1) Add support for BPF line info via BTF and extend libbpf as well
as bpftool's program dump to annotate output with BPF C code to
facilitate debugging and introspection, from Martin.
2) Add support for BPF_ALU | BPF_ARSH | BPF_{K,X} in interpreter
and all JIT backends, from Jiong.
3) Improve BPF test coverage on archs with no efficient unaligned
access by adding an "any alignment" flag to the BPF program load
to forcefully disable verifier alignment checks, from David.
4) Add a new bpf_prog_test_run_xattr() API to libbpf which allows for
proper use of BPF_PROG_TEST_RUN with data_out, from Lorenz.
5) Extend tc BPF programs to use a new __sk_buff field called wire_len
for more accurate accounting of packets going to wire, from Petar.
6) Improve bpftool to allow dumping the trace pipe from it and add
several improvements in bash completion and map/prog dump,
from Quentin.
7) Optimize arm64 BPF JIT to always emit movn/movk/movk sequence for
kernel addresses and add a dedicated BPF JIT backend allocator,
from Ard.
8) Add a BPF helper function for IR remotes to report mouse movements,
from Sean.
9) Various cleanups in BPF prog dump e.g. to make UAPI bpf_prog_info
member naming consistent with existing conventions, from Yonghong
and Song.
10) Misc cleanups and improvements in allowing to pass interface name
via cmdline for xdp1 BPF example, from Matteo.
11) Fix a potential segfault in BPF sample loader's kprobes handling,
from Daniel T.
12) Fix SPDX license in libbpf's README.rst, from Andrey.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The egdev mechanism was replaced by the TC indirect block notifications
platform.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Cc: John Hurley <john.hurley@netronome.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Changed the is_gretap_dev and is_ip6gretap_dev logic from structure
comparison to string comparison of the rtnl_link_ops kind field.
This approach aligns with the current identification methods and function
names of vxlan and geneve network devices.
Convert mlxsw to use these helpers and use them in downstream mlx5 patch.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
vr.vifi is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
net/ipv4/ipmr.c:1616 ipmr_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
net/ipv4/ipmr.c:1690 ipmr_compat_ioctl() warn: potential spectre issue 'mrt->vif_table' [r] (local cap)
Fix this by sanitizing vr.vifi before using it to index mrt->vif_table'
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit f9bfe4e6a9 ("tcp: lack of available data can also cause
TSO defer") we moved the test in tcp_tso_should_defer() for packets
with a FIN flag, and we mentioned that the same would be done
later for EOR flag.
Both flags should be handled at the same time, after all other
heuristics have been considered. They both mean that no more bytes
can be added to this skb by an application.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a kernel-infoleak, which is caused by an uninitialized
field(sin6_flowinfo) of addr->a.v6 in sctp_inet6addr_event().
The call trace is as below:
BUG: KMSAN: kernel-infoleak in _copy_to_user+0x19a/0x230 lib/usercopy.c:33
CPU: 1 PID: 8164 Comm: syz-executor2 Not tainted 4.20.0-rc3+ #95
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x32d/0x480 lib/dump_stack.c:113
kmsan_report+0x12c/0x290 mm/kmsan/kmsan.c:683
kmsan_internal_check_memory+0x32a/0xa50 mm/kmsan/kmsan.c:743
kmsan_copy_to_user+0x78/0xd0 mm/kmsan/kmsan_hooks.c:634
_copy_to_user+0x19a/0x230 lib/usercopy.c:33
copy_to_user include/linux/uaccess.h:183 [inline]
sctp_getsockopt_local_addrs net/sctp/socket.c:5998 [inline]
sctp_getsockopt+0x15248/0x186f0 net/sctp/socket.c:7477
sock_common_getsockopt+0x13f/0x180 net/core/sock.c:2937
__sys_getsockopt+0x489/0x550 net/socket.c:1939
__do_sys_getsockopt net/socket.c:1950 [inline]
__se_sys_getsockopt+0xe1/0x100 net/socket.c:1947
__x64_sys_getsockopt+0x62/0x80 net/socket.c:1947
do_syscall_64+0xcf/0x110 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
sin6_flowinfo is not really used by SCTP, so it will be fixed by simply
setting it to 0.
The issue exists since very beginning.
Thanks Alexander for the reproducer provided.
Reported-by: syzbot+ad5d327e6936a2e284be@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"A decent batch of fixes here. I'd say about half are for problems that
have existed for a while, and half are for new regressions added in
the 4.20 merge window.
1) Fix 10G SFP phy module detection in mvpp2, from Baruch Siach.
2) Revert bogus emac driver change, from Benjamin Herrenschmidt.
3) Handle BPF exported data structure with pointers when building
32-bit userland, from Daniel Borkmann.
4) Memory leak fix in act_police, from Davide Caratti.
5) Check RX checksum offload in RX descriptors properly in aquantia
driver, from Dmitry Bogdanov.
6) SKB unlink fix in various spots, from Edward Cree.
7) ndo_dflt_fdb_dump() only works with ethernet, enforce this, from
Eric Dumazet.
8) Fix FID leak in mlxsw driver, from Ido Schimmel.
9) IOTLB locking fix in vhost, from Jean-Philippe Brucker.
10) Fix SKB truesize accounting in ipv4/ipv6/netfilter frag memory
limits otherwise namespace exit can hang. From Jiri Wiesner.
11) Address block parsing length fixes in x25 from Martin Schiller.
12) IRQ and ring accounting fixes in bnxt_en, from Michael Chan.
13) For tun interfaces, only iface delete works with rtnl ops, enforce
this by disallowing add. From Nicolas Dichtel.
14) Use after free in liquidio, from Pan Bian.
15) Fix SKB use after passing to netif_receive_skb(), from Prashant
Bhole.
16) Static key accounting and other fixes in XPS from Sabrina Dubroca.
17) Partially initialized flow key passed to ip6_route_output(), from
Shmulik Ladkani.
18) Fix RTNL deadlock during reset in ibmvnic driver, from Thomas
Falcon.
19) Several small TCP fixes (off-by-one on window probe abort, NULL
deref in tail loss probe, SNMP mis-estimations) from Yuchung
Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (93 commits)
net/sched: cls_flower: Reject duplicated rules also under skip_sw
bnxt_en: Fix _bnxt_get_max_rings() for 57500 chips.
bnxt_en: Fix NQ/CP rings accounting on the new 57500 chips.
bnxt_en: Keep track of reserved IRQs.
bnxt_en: Fix CNP CoS queue regression.
net/mlx4_core: Correctly set PFC param if global pause is turned off.
Revert "net/ibm/emac: wrong bit is used for STA control"
neighbour: Avoid writing before skb->head in neigh_hh_output()
ipv6: Check available headroom in ip6_xmit() even without options
tcp: lack of available data can also cause TSO defer
ipv6: sr: properly initialize flowi6 prior passing to ip6_route_output
mlxsw: spectrum_switchdev: Fix VLAN device deletion via ioctl
mlxsw: spectrum_router: Relax GRE decap matching check
mlxsw: spectrum_switchdev: Avoid leaking FID's reference count
mlxsw: spectrum_nve: Remove easily triggerable warnings
ipv4: ipv6: netfilter: Adjust the frag mem limit when truesize changes
sctp: frag_point sanity check
tcp: fix NULL ref in tail loss probe
tcp: Do not underestimate rwnd_limited
net: use skb_list_del_init() to remove from RX sublists
...
Currently, duplicated rules are rejected only for skip_hw or "none",
hence allowing users to push duplicates into HW for no reason.
Use the flower tables to protect for that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reported-by: Chris Mi <chrism@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous change tries to set the MTU on the master device to take
into account the DSA overheads. This patch tries to reset the master
device back to the default MTU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
extra_uref is used in __ip(6)_append_data only if uarg is set.
Smatch sees that the variable is passed to sock_zerocopy_put_abort.
This function accesses it only when uarg is set, but smatch cannot
infer this.
Make this dependency explicit.
Fixes: 52900d2228 ("udp: elide zerocopy operation in hot path")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if we send an IPv6 packet without options, MAX_HEADER might not be
enough to account for the additional headroom required by alignment of
hardware headers.
On a configuration without HYPERV_NET, WLAN, AX25, and with IPV6_TUNNEL,
sending short SCTP packets over IPv4 over L2TP over IPv6, we start with
100 bytes of allocated headroom in sctp_packet_transmit(), end up with 54
bytes after l2tp_xmit_skb(), and 14 bytes in ip6_finish_output2().
Those would be enough to append our 14 bytes header, but we're going to
align that to 16 bytes, and write 2 bytes out of the allocated slab in
neigh_hh_output().
KASan says:
[ 264.967848] ==================================================================
[ 264.967861] BUG: KASAN: slab-out-of-bounds in ip6_finish_output2+0x1aec/0x1c70
[ 264.967866] Write of size 16 at addr 000000006af1c7fe by task netperf/6201
[ 264.967870]
[ 264.967876] CPU: 0 PID: 6201 Comm: netperf Not tainted 4.20.0-rc4+ #1
[ 264.967881] Hardware name: IBM 2827 H43 400 (z/VM 6.4.0)
[ 264.967887] Call Trace:
[ 264.967896] ([<00000000001347d6>] show_stack+0x56/0xa0)
[ 264.967903] [<00000000017e379c>] dump_stack+0x23c/0x290
[ 264.967912] [<00000000007bc594>] print_address_description+0xf4/0x290
[ 264.967919] [<00000000007bc8fc>] kasan_report+0x13c/0x240
[ 264.967927] [<000000000162f5e4>] ip6_finish_output2+0x1aec/0x1c70
[ 264.967935] [<000000000163f890>] ip6_finish_output+0x430/0x7f0
[ 264.967943] [<000000000163fe44>] ip6_output+0x1f4/0x580
[ 264.967953] [<000000000163882a>] ip6_xmit+0xfea/0x1ce8
[ 264.967963] [<00000000017396e2>] inet6_csk_xmit+0x282/0x3f8
[ 264.968033] [<000003ff805fb0ba>] l2tp_xmit_skb+0xe02/0x13e0 [l2tp_core]
[ 264.968037] [<000003ff80631192>] l2tp_eth_dev_xmit+0xda/0x150 [l2tp_eth]
[ 264.968041] [<0000000001220020>] dev_hard_start_xmit+0x268/0x928
[ 264.968069] [<0000000001330e8e>] sch_direct_xmit+0x7ae/0x1350
[ 264.968071] [<000000000122359c>] __dev_queue_xmit+0x2b7c/0x3478
[ 264.968075] [<00000000013d2862>] ip_finish_output2+0xce2/0x11a0
[ 264.968078] [<00000000013d9b14>] ip_finish_output+0x56c/0x8c8
[ 264.968081] [<00000000013ddd1e>] ip_output+0x226/0x4c0
[ 264.968083] [<00000000013dbd6c>] __ip_queue_xmit+0x894/0x1938
[ 264.968100] [<000003ff80bc3a5c>] sctp_packet_transmit+0x29d4/0x3648 [sctp]
[ 264.968116] [<000003ff80b7bf68>] sctp_outq_flush_ctrl.constprop.5+0x8d0/0xe50 [sctp]
[ 264.968131] [<000003ff80b7c716>] sctp_outq_flush+0x22e/0x7d8 [sctp]
[ 264.968146] [<000003ff80b35c68>] sctp_cmd_interpreter.isra.16+0x530/0x6800 [sctp]
[ 264.968161] [<000003ff80b3410a>] sctp_do_sm+0x222/0x648 [sctp]
[ 264.968177] [<000003ff80bbddac>] sctp_primitive_ASSOCIATE+0xbc/0xf8 [sctp]
[ 264.968192] [<000003ff80b93328>] __sctp_connect+0x830/0xc20 [sctp]
[ 264.968208] [<000003ff80bb11ce>] sctp_inet_connect+0x2e6/0x378 [sctp]
[ 264.968212] [<0000000001197942>] __sys_connect+0x21a/0x450
[ 264.968215] [<000000000119aff8>] sys_socketcall+0x3d0/0xb08
[ 264.968218] [<000000000184ea7a>] system_call+0x2a2/0x2c0
[...]
Just like ip_finish_output2() does for IPv4, check that we have enough
headroom in ip6_xmit(), and reallocate it if we don't.
This issue is older than git history.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_tso_should_defer() can return true in three different cases :
1) We are cwnd-limited
2) We are rwnd-limited
3) We are application limited.
Neal pointed out that my recent fix went too far, since
it assumed that if we were not in 1) case, we must be rwnd-limited
Fix this by properly populating the is_cwnd_limited and
is_rwnd_limited booleans.
After this change, we can finally move the silly check for FIN
flag only for the application-limited case.
The same move for EOR bit will be handled in net-next,
since commit 1c09f7d073 ("tcp: do not try to defer skbs
with eor mark (MSG_EOR)") is scheduled for linux-4.21
Tested by running 200 concurrent netperf -t TCP_RR -- -r 60000,100
and checking none of them was rwnd_limited in the chrono_stat
output from "ss -ti" command.
Fixes: 41727549de ("tcp: Do not underestimate rwnd_limited")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
after set SO_DONTROUTE to 1, the IP layer should not route packets if
the dest IP address is not in link scope. But if the socket has cached
the dst_entry, such packets would be routed until the sk_dst_cache
expires. So we should clean the sk_dst_cache when a user set
SO_DONTROUTE option. Below are server/client python scripts which
could reprodue this issue:
server side code:
==========================================================================
import socket
import struct
import time
s = socket.socket(socket.AF_INET, socket.SOCK_STREAM)
s.bind(('0.0.0.0', 9000))
s.listen(1)
sock, addr = s.accept()
sock.setsockopt(socket.SOL_SOCKET, socket.SO_DONTROUTE, struct.pack('i', 1))
while True:
sock.send(b'foo')
time.sleep(1)
==========================================================================
client side code:
==========================================================================
import socket
import time
s = socket.socket(socket.AF_INET, socket.SOCK_STREAM)
s.connect(('server_address', 9000))
while True:
data = s.recv(1024)
print(data)
==========================================================================
Signed-off-by: yupeng <yupeng0921@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing garbage collection algorithm has a number of problems:
1. The gc algorithm will not evict PERMANENT entries as those entries
are managed by userspace, yet the existing algorithm walks the entire
hash table which means it always considers PERMANENT entries when
looking for entries to evict. In some use cases (e.g., EVPN) there
can be tens of thousands of PERMANENT entries leading to wasted
CPU cycles when gc kicks in. As an example, with 32k permanent
entries, neigh_alloc has been observed taking more than 4 msec per
invocation.
2. Currently, when the number of neighbor entries hits gc_thresh2 and
the last flush for the table was more than 5 seconds ago gc kicks in
walks the entire hash table evicting *all* entries not in PERMANENT
or REACHABLE state and not marked as externally learned. There is no
discriminator on when the neigh entry was created or if it just moved
from REACHABLE to another NUD_VALID state (e.g., NUD_STALE).
It is possible for entries to be created or for established neighbor
entries to be moved to STALE (e.g., an external node sends an ARP
request) right before the 5 second window lapses:
-----|---------x|----------|-----
t-5 t t+5
If that happens those entries are evicted during gc causing unnecessary
thrashing on neighbor entries and userspace caches trying to track them.
Further, this contradicts the description of gc_thresh2 which says
"Entries older than 5 seconds will be cleared".
One workaround is to make gc_thresh2 == gc_thresh3 but that negates the
whole point of having separate thresholds.
3. Clearing *all* neigh non-PERMANENT/REACHABLE/externally learned entries
when gc_thresh2 is exceeded is over kill and contributes to trashing
especially during startup.
This patch addresses these problems as follows:
1. Use of a separate list_head to track entries that can be garbage
collected along with a separate counter. PERMANENT entries are not
added to this list.
The gc_thresh parameters are only compared to the new counter, not the
total entries in the table. The forced_gc function is updated to only
walk this new gc_list looking for entries to evict.
2. Entries are added to the list head at the tail and removed from the
front.
3. Entries are only evicted if they were last updated more than 5 seconds
ago, adhering to the original intent of gc_thresh2.
4. Forced gc is stopped once the number of gc_entries drops below
gc_thresh2.
5. Since gc checks do not apply to PERMANENT entries, gc levels are skipped
when allocating a new neighbor for a PERMANENT entry. By extension this
means there are no explicit limits on the number of PERMANENT entries
that can be created, but this is no different than FIB entries or FDB
entries.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to make sure that the following condition holds:
0 <= nhoff <= thoff <= skb->len
BPF program can set out-of-bounds nhoff and thoff, which is dangerous, see
recent commit d0c081b491 ("flow_dissector: properly cap thoff field")'.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We are returning thoff from the flow dissector, not the nhoff. Pass
thoff along with nhoff to the bpf program (initially thoff == nhoff)
and expect flow dissector amend/return thoff, not nhoff.
This avoids confusion, when by the time bpf flow dissector exits,
nhoff == thoff, which doesn't make much sense.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When a driver unoffloads all FDB entries en bloc, it's inefficient to
send the switchdev notification one by one. Add a helper that unsets the
offload flag on FDB entries on a given bridge port and VLAN.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal