ATA_HORKAGE_DMA_RW_ONLY for TORiSAN is verified to be subset of using
DMA for ATAPI commands which aren't aligned to 16 bytes. As libata
now doesn't use DMA for unaligned ATAPI commands, the horkage is
redundant. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The IDE driver used DMA for ATAPI commands if READ/WRITE command is
multiple of sector size or sg command is multiple of 16 bytes. For
libata, READ/WRITE sector alignment is guaranteed by the high level
driver (sr), so we only have to worry about the 16 byte alignment.
This patch makes ata_check_atapi_dma() always request PIO for all data
transfer commands which are not multiple of 16 bytes.
The following reports are related to this problem.
http://bugzilla.kernel.org/show_bug.cgi?id=8605 (confirmed)
http://thread.gmane.org/gmane.linux.kernel/476620 (confirmed)
https://bugzilla.novell.com/show_bug.cgi?id=229260 (probably)
Albert first pointed out the difference between IDE and libata. Kudos
to him.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In atapi_xlat(), prepare qc better before calling
ata_check_atapi_dma() such that ata_check_atapi_dma() can use info
from qc. While at it, reformat weird looking if/else block in the
function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When EH gives up after repeated exceptions, it doesn't't clear the
PENDING bit on exit which leaves PENDING bit set without EH actually
scheduled. This makes ata_port_wait_eh() to wait forever makes rmmod
hang on such port. Fix it by clearing the flag.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix section mismatch when CONFIG_HOTPLUG=n (but functions are used
for resume):
WARNING: drivers/ata/pata_it821x.o(.text+0x3f): Section mismatch: reference to .init.text: (between 'it821x_reinit_one' and 'it821x_program_udma')
WARNING: drivers/ata/pata_it821x.o(.text+0x691): Section mismatch: reference to .init.text: (between 'it821x_init_one' and 'it821x_passthru_set_dmamode')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's no reason to print out hpa related messages when HPA is not
active. Kill the unconditional message and add a warning message
which is printed if HPA size is smaller than the current size.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
prereset() is now allowed to set flag for unsupported reset method.
EH layer is responsible for selecting the fallback. Remove non-sense
warning message.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The attached patch fixes a trivial
mistake in a MODULE_PARAM_DESC of pata_it821x
driver. The parameter name in MODULE_PARAM_DESC
should match the one in module_param_named.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If PORTS_IMPL register is zero, ahci initialize it to full mask
corresponding to nr_ports in the CAP register. hpriv->cap, which is
initialized at the end of the function, is incorrectly used as value
of CAP causing ahci to always override PORTS_IMPL to 0x1 if it's zero.
Fix it.
This fixes a bug where early ich6 ahci can only access the first port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix parameter name from ata_dev_reread_id() in libata-core.c for kerneldoc.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More for the NCQ blacklist. One hitachi and one raptor. Other
members of these families of drives are already on the list, so no
surprises.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code intended to check DMA status was checking DMA command register.
Moreover firmware seems to "forget" to set DMA capable bit for the
slave device (at least in RAID mode but without ITE RAID volumes) so
check device ID for DMA capable bit when deciding whether to use DMA
and remove DMA status check completely.
Thanks to Pavol Simo for the bugreport and testing the initial fix.
This change unfortunately still doesn't fix DMA in RAID mode (which
works fine with IDE it821x) but Alan is working on the missing pieces
(pata_it821x vs libata EH issues).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the MCP73/MCP77 support to PATA driver.
The patch base on kernel 2.6.22-rc4
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After SRST, libata used to wait for nsect/lbal to be set to 1/1 for
the slave device. However, some ATAPI devices don't set nsect/lbal
after SRST and the wait itself isn't too useful as we're gonna wait
for !BSY right after that anyway.
Before reset-seq update, nsect/lbal wait failure used to be ignored
and caused 30sec delay during detection. After reset-seq, all
timeouts are considered error conditions making libata fail to detect
such ATAPI devices.
This patch limits nsect/lbal wait to around 100ms. This should give
acceptable behavior to such ATAPI devices while not disturbing the
heavily used code path too much.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
IOMEGA ZIP 250 ATAPI claims MWDMA0 support but fails SETXFERMODE if
asked to configure itself to MWDMA0. Force PIO.
This fixes bugzilla bug#8497.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Calvin Walton <calvin.walton@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
INIT_DEV_PARAMS and SET_MULTI_MODE change the device parameters cached
by libata. Re-read IDENTIFY DEVICE info and update the cached device
paramters when seeing these commands.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Always enforce correct DEV bit since we know which drive the command
is targeted. SAT demands to ignore the DEV bit, too.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the ATA passthru protocol numbers according to the new spec.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The controller is not reporting an unlawful type, it is reporting an
invalid type. Illegal specifically means "prohibited by law"
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ata IRQ ack functions are only used when debugging. Unfortunately
almost every controller that calls them can cause crashes in some
configurations as there are missing checks for bmdma presence.
In addition ata_port_start insists of installing DMA buffers and pad
buffers for controllers regardless. The SFF controllers actually need to
make that decision dynamically at controller setup time and all need the
same helper - so we add ata_sff_port_start. Future patches will switch
the SFF drivers to use this.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hw_sata_spd_limit used to be incorrectly initialized to zero instead
of UINT_MAX if SPD is zero in SControl register. This breaks PHY
speed down. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For ATA/CFA devices, libata prints out the device model and firmware revision.
Do the same for ATAPI devices.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Most drivers don't seem to fill out the host->irq field, resulting in the
wrong (no) irq being reported at probe time. For example, sil24 on my system:
ata1: SATA max UDMA/100 cmd 0xd00008009001f000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata2: SATA max UDMA/100 cmd 0xd000080090021000 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
Since they're allocated and set up in ata_host_activate(), just save
them away there.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch has removed unused variable in pata_ispnp.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_promise uses two different command modes - packet and TF. Packet mode
is intelligent low-overhead mode while TF is the same old taskfile
interface. As with other advanced interface (ahci/sil24),
ATA_TFLAG_POLLING has no effect in packet mode. However, PIO commands are
issued using TF interface in polling mode, so pdc_interrupt() considers
interrupts spurious if ATA_TFLAG_POLLING is set.
This is broken for polling NODATA commands because command is issued using
packet mode but the interrupt handler ignores it due to ATA_TFLAG_POLLING.
Fix pdc_qc_issue_prot() such that ATA/ATAPI NODATA commands are issued
using TF interface if ATA_TFLAG_POLLING is set.
This patch fixes detection failure introduced by polling SETXFERMODE.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several people have reported LITE-ON LTR-48246S detection failed
because SETXFER fails. It seems the device raises IRQ too early after
SETXFER. This is controller independent. The same problem has been
reported for different controllers.
So, now we have pata_via where the controller raises IRQ before it's
ready after SETXFER and a device which does similar thing. This patch
makes libata always execute SETXFER via polling. As this only happens
during EH, performance impact is nil. Setting ATA_TFLAG_POLLING is
also moved from issue hot path to ata_dev_set_xfermode() - the only
place where SETXFER can be issued.
Note that ATA_TFLAG_POLLING applies only to drivers which implement
SFF TF interface and use libata HSM. More advanced controllers ignore
the flag. This doesn't matter for this fix as SFF TF controllers are
the problematic ones.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Supplied by VIA.
Also, convert named constants to hex values in the pata_via
PCI ID table. (standard libata policy for PCI device IDs, which are
considered simply arbitrary hex numbers, without a need to create a
single-use constant in linux/pci_ids.h)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sata_sis driver supports SATA and PATA ports. The broken support
of both types in one controller is fixed.
Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The commit d4b2bab4f2 added deadline support
to prereset and reset methods to libbata the pata_scc driver wasn't
converted. This patch is a naive attempt to bring this driver up to
scratch.
Build failures are:
drivers/ata/pata_scc.c: In function 'scc_pata_prereset':
drivers/ata/pata_scc.c:870: error: too few arguments to function 'ata_std_prereset'
drivers/ata/pata_scc.c: In function 'scc_error_handler':
drivers/ata/pata_scc.c:916: warning: passing argument 2 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c:916: warning: passing argument 3 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c: In function 'scc_pata_prereset':
drivers/ata/pata_scc.c:871: warning: control reaches end of non-void function
On a releated note scc_bus_post_reset() is (AFACT) identical to
ata_bus_post_reset(), would a patch to make ata_bus_post_reset() assesable
to drivers be accepted?
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Oh the joy of saving a fraction of a cent using short 40 wire cables and
not faking 80wire
Teach the VIA driver that there are some systems we need to know are
magically wired for high speeds.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Francis Russell <FrancisRussell@btinternet.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During prereset, -ENODEV return from ata_wait_ready() is not an error.
This causes unnecessary bug message on controllers which uses 0xff to
indicate empty port. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some SATA controllers (sata_sil) use 0xff to indicate port not ready
status, not port empty. As libata interprets 0xff as port empty, this
causes unnecessary reset failure and retry. Don't consider 0xff as
port empty if SStatus is available and indicates that port is online.
Signed-off-by: tejun Heo <htejun@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Indan Zupancic <indan@nul.nu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acer Aspire 2023WLMi uses short 40c cable. Add quirk for it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Steve H. <mail.pandor@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Rename sis_port_base to sis_old_port_base() so nobody uses it for new
generation controllers in error.
- Use byte size operations where it is cleaner for mode setup
- Fix a couple of masking errors on certai chip revs when setting speeds
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We have a revision that isn't correctly claimed as two drivers both go
for it: Fix the test accordingly. Noticed originally by Bill Nottingham.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo