Ux500 is regressing due to commit
a21763a0b1
"pinctrl: nomadik: activate strict mux mode" which disallows
Nomadik GPIO 5 to be muxed in as a level shifter voltage select
pin, as it is currently described as being used for RX on UART1.
The behaviour is correct, instead the hardware config has been
incorrecly specified: UART1 is indeed unused on HREFv60plus and
Snowball and that is why HREFv60plus can use the pins it would
normally occupy as the voltage select line for the MMC/SD
levelshifter (Snowball uses it for I2C4).
The reason UART1 was anyway enabled on these platforms was
probably to secure the port enumeration to userspace. This
can be solved by using aliases (done in a separate patch) so
we can now deactivate UART1 and let MMC/SD use it properly
on HREFv60plus. We explicitly activate it only for the
older HREFprev60 board.
To complete, we set up the pin configuration for these pins
properly in the sdi0 node.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This enumerates the PL011 serial ports on the Ux500. This is
necessary to do if we want to remove one of the serial ports,
since userspace depends on console to be present on ttyAMA2
and we must not break userspace.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Previously only core DRM ioctls under the DRM_COMMAND_BASE were being
forwarded, but the drm.h header suggests (and reality confirms) ones
after (and including) DRM_COMMAND_END should be forwarded as well.
We need this to correctly forward the compat ioctl for the botched-up
addfb2.1 extension.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: stable@vger.kernel.org # 4.1+
[danvet: Explain why this is suddenly needed and add cc: stable.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add missing #iommu-cells property to the DSP and IPU IOMMU nodes
for OMAP5 platforms. This property is required as per the generic
iommu binding.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing #iommu-cells property to the DSP and IPU IOMMU nodes
for OMAP4 platforms. This property is required as per the generic
iommu binding.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The device tree for Gumstix Pepper has DCDC2 and
DCDC3 correctly labelled but the upper limit values
are wrong. The confusion is due to the hardware
quirk where the DCDC2 and DCDC3 wires are flipped
in Pepper.
Signed-off-by: Arun Bharadwaj <arun@gumstix.com>
Tested-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Boot process is halting in midway because some of the necessary voltage
regulators are deemed unused and subsequently powered off, leading to
a completely unresponsive system.
Most of the device nodes had correct voltage regulator attachments.
Yet these nodes had to set stricter enforcement on them through
'regulator-boot-on' and 'regulator-always-on' to function correctly.
The consumers of the regulators this commit affect are the followings:
DCDC1: vdd_1v8 system supply, USB-PHY, and ADC
DCDC2: Core domain
DCDC3: MPU core domain
LDO1: RTC
LDO2: 3v3 IO domain
LDO3: USB-PHY; not a boot-time requirement
LDO4: LCD [16:23]
All but LDO3 need to be always-on for the system to be functional.
Additionally regulator-name properties have been added for the kernel to
display the name from the schematic. This will improve diagnostics.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For Gumstix Overo COMs, the u-boot bootloader typically passes an
argument specifying the default display via the omapdss.def_disp
parameter. When a default display is specified, DSS2 tries to match
this name with either the device tree label (e.g. label=dvi) or,
failing this, the device tree alias (e.g. label=display0). Update the
panel names for the 'lcd43' and 'lcd35' displays in the device tree
such that they match the names passed by u-boot.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for 4 Japanese keys
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
At least some versions of AMI BIOS have corrupted contents in the TPM2
ACPI table and namely the physical address of the control area is set to
zero.
This patch changes the driver to fail gracefully when we observe a zero
address instead of continuing to ioremap.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
When a cdev is contained in a dynamic structure the cdev parent kobj
should be set to the kobj that controls the lifetime of the enclosing
structure. In TPM's case this is the embedded struct device.
Also, cdev_init 0's the whole structure, so all sets must be after,
not before. This fixes module ref counting and cdev.
Cc: <stable@vger.kernel.org>
Fixes: 313d21eeab ("tpm: device class for tpm")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
material in the recent merge window, hence their separation from set (a)
as the fixes-togreg branch predated the merge window. I am running rather
later with these than I would have liked hence the large set.
* stk3310 fixes from Hartmut's review that came in post merge
- fix direction of proximity inline with recent documentation
clarification.
- fix missing REGMAP_I2C dependency
- rework the error handling for raw readings to fix an failure to power
down in the event of a raw reading failing.
- fix a bug in the compensation code which was toggling an extra bit in the
register.
* mmc35240 - reported samplign frequencies were wrong.
* ltr501 fixes
- fix a case of returning the return value of a regmap_read instead of
the value read.
- fix missing regmap dependency
* sx9500 - fix missing default values for ret in a couple of places to handle
the case of no enabled channels.
* tmp006 - check that writes to info_mask elements are actually to writable
ones. Otherwise, writing to any of them will change the sampling frequency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1kNg
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.2 cycle. Note these depend (mostly) on
material in the recent merge window, hence their separation from set (a)
as the fixes-togreg branch predated the merge window. I am running rather
later with these than I would have liked hence the large set.
* stk3310 fixes from Hartmut's review that came in post merge
- fix direction of proximity inline with recent documentation
clarification.
- fix missing REGMAP_I2C dependency
- rework the error handling for raw readings to fix an failure to power
down in the event of a raw reading failing.
- fix a bug in the compensation code which was toggling an extra bit in the
register.
* mmc35240 - reported samplign frequencies were wrong.
* ltr501 fixes
- fix a case of returning the return value of a regmap_read instead of
the value read.
- fix missing regmap dependency
* sx9500 - fix missing default values for ret in a couple of places to handle
the case of no enabled channels.
* tmp006 - check that writes to info_mask elements are actually to writable
ones. Otherwise, writing to any of them will change the sampling frequency.
* Fix a regression in hid sensors suspend time as a result of adding runtime
pm. The normal flow of waking up devices in order to go into suspend
(given the devices are normally suspended when not reading) to a regression
in suspend time on some laptops (reports of an additional 8 seconds).
Fix this by checking to see if a user action resulting in the wake up, and
make it a null operation if it didn't. Note that for hid sensors, there is
nothing useful to be done when moving into a full suspend from a runtime
suspend so they might as well be left alone.
* rochip_saradc: fix some missing MODULE_* data including the licence so that
the driver does not taint the kernel incorrectly and can build as a module.
* twl4030 - mark irq as oneshot as it always should have been.
* inv-mpu - write formats for attributes not specified, leading to miss
interpretation of the gyro scale channel when written.
* Proximity ABI clarification. This had snuck through as a mess. Some
drivers thought proximity went in one direction, some the other. We went
with the most common option, documented it and fixed up the drivers going
the other way. Fix for sx9500 included in this set.
* ad624r - fix a wrong shift in the output data.
* at91_adc - remove a false limit on the value of the STARTUP register
applied by too small a type for the device tree parameter.
* cm3323 - clear the bits when setting the integration time (otherwise
we can only ever set more bits in the relevant field).
* bmc150-accel - multiple triggers are registered, but on error were not being
unwound in the opposite order leading to removal of triggers that had not
yet successfully been registered (count down instead of up when unwinding).
* tcs3414 - ensure right part of val / val2 pair read so that the integration
time is not always 0.
* cc10001_adc - bug in kconfig dependency. Use of OR when AND was intended.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mBqw
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.2 cycle.
* Fix a regression in hid sensors suspend time as a result of adding runtime
pm. The normal flow of waking up devices in order to go into suspend
(given the devices are normally suspended when not reading) to a regression
in suspend time on some laptops (reports of an additional 8 seconds).
Fix this by checking to see if a user action resulting in the wake up, and
make it a null operation if it didn't. Note that for hid sensors, there is
nothing useful to be done when moving into a full suspend from a runtime
suspend so they might as well be left alone.
* rochip_saradc: fix some missing MODULE_* data including the licence so that
the driver does not taint the kernel incorrectly and can build as a module.
* twl4030 - mark irq as oneshot as it always should have been.
* inv-mpu - write formats for attributes not specified, leading to miss
interpretation of the gyro scale channel when written.
* Proximity ABI clarification. This had snuck through as a mess. Some
drivers thought proximity went in one direction, some the other. We went
with the most common option, documented it and fixed up the drivers going
the other way. Fix for sx9500 included in this set.
* ad624r - fix a wrong shift in the output data.
* at91_adc - remove a false limit on the value of the STARTUP register
applied by too small a type for the device tree parameter.
* cm3323 - clear the bits when setting the integration time (otherwise
we can only ever set more bits in the relevant field).
* bmc150-accel - multiple triggers are registered, but on error were not being
unwound in the opposite order leading to removal of triggers that had not
yet successfully been registered (count down instead of up when unwinding).
* tcs3414 - ensure right part of val / val2 pair read so that the integration
time is not always 0.
* cc10001_adc - bug in kconfig dependency. Use of OR when AND was intended.
On Sun, Jul 12, 2015 at 09:52:51AM -0700, Linus Torvalds wrote:
> On Sun, Jul 12, 2015 at 1:03 AM, Jörg Otte <jrg.otte@gmail.com> wrote:
> > BUG: unable to handle kernel NULL pointer dereference at 0000000000000009
> > IP: [<ffffffffbd3447bb>] 0xffffffffbd3447bb
>
> Ugh. Please enable KALLSYMS to get sane symbols.
>
> But yes, "crtc_state->base.active" is at offset 9 from "crtc_state",
> so it's pretty clearly just that change frm
>
> - if (intel_crtc->active) {
> + if (crtc_state->base.active) {
>
> and "crtc_state" is NULL.
>
> And the code very much knows that crtc_state can be NULL, since it's
> initialized with
>
> crtc_state = state->base.state ?
> intel_atomic_get_crtc_state(state->base.state,
> intel_crtc) : NULL;
>
> Tssk. Daniel? Should I just revert that commit dec4f799d0
> ("drm/i915: Use crtc_state->active in primary check_plane func") for
> now, or is there a better fix? Like just checking crtc_state for NULL?
Indeed embarrassing. I've missed that we still have 1 caller left that's
using the transitional helpers, and those don't fill out
plane_state->state backpointers to the global atomic update since there is
no global atomic update for transitional helpers. Below diff should fix
this - we need to preferentially check crts_state->active and if that's
not set intel_crtc->active should yield the right result for the one
remaining caller (it's in the crtc_disable paths).
This fixes a regression introduced in
commit dec4f799d0
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jul 7 11:15:47 2015 +0200
drm/i915: Use crtc_state->active in primary check_plane func
which was quickly reverted in
commit 01e2d0627a
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Jul 12 15:00:20 2015 -0700
Revert "drm/i915: Use crtc_state->active in primary check_plane func"
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jörg Otte <jrg.otte@gmail.com>
Reported-and-tested-by: Jörg Otte <jrg.otte@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
After the previous patch this flag will check always clear, as it's
never set for shmem backed and userptr objects, so we can remove it.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Yeah this isn't really fixes but it's a nice cleanup to
clarify the code but not really worth the hassle of backmerging. So
just add to -fixes, we're still early in -rc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This broken code was introduced in
commit aa7471d228
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 1 11:15:21 2015 +0300
drm/i915: add i915 specific connector debugfs file for DPCD
v2: Drop hunk that accidentally crept in.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: François Valenduc <francoisvalenduc@gmail.com>
Reported-by: François Valenduc <francoisvalenduc@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We have 3 types of DMA mappings for GEM objects:
1. physically contiguous for stolen and for objects needing contiguous
memory
2. DMA-buf mappings imported via a DMA-buf attach operation
3. SG DMA mappings for shmem backed and userptr objects
For 1. and 2. the lifetime of the DMA mapping matches the lifetime of the
corresponding backing pages and so in practice we create/release the
mapping in the object's get_pages/put_pages callback.
For 3. the lifetime of the mapping matches that of any existing GPU binding
of the object, so we'll create the mapping when the object is bound to
the first vma and release the mapping when the object is unbound from its
last vma.
Since the object can be bound to multiple vmas, we can end up creating a
new DMA mapping in the 3. case even if the object already had one. This
is not allowed by the DMA API and can lead to leaked mapping data and
IOMMU memory space starvation in certain cases. For example HW IOMMU
drivers (intel_iommu) allocate a new range from their memory space
whenever a mapping is created, silently overriding a pre-existing
mapping.
Fix this by moving the creation/removal of DMA mappings to the object's
get_pages/put_pages callbacks. These callbacks already check for and do
an early return in case of any nested calls. This way objects of the 3.
case also become more like the other object types.
I noticed this issue by enabling DMA debugging, which got disabled after
a while due to its internal mapping tables getting full. It also reported
errors in connection to random other drivers that did a DMA mapping for
an address that was previously mapped by i915 but was never released.
Besides these diagnostic messages and the memory space starvation
problem for IOMMUs, I'm not aware of this causing a real issue.
The fix is based on a patch from Chris.
v2:
- move the DMA mapping create/remove calls to the get_pages/put_pages
callbacks instead of adding new callbacks for these (Chris)
v3:
- also fix the get_page cache logic on the userptr async path (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The hang checker needs to inspect whether or not the ring request list is empty
as well as if the given engine has reached or passed the most recently
submitted request. The problem with this is that the hang checker cannot grab
the struct_mutex, which is required in order to safely inspect requests since
requests might be deallocated during inspection. In the past we've had kernel
panics due to this very unsynchronized access in the hang checker.
One solution to this problem is to not inspect the requests directly since
we're only interested in the seqno of the most recently submitted request - not
the request itself. Instead the seqno of the most recently submitted request is
stored separately, which the hang checker then inspects, circumventing the
issue of synchronization from the hang checker entirely.
This fixes a regression introduced in
commit 44cdd6d219
Author: John Harrison <John.C.Harrison@Intel.com>
Date: Mon Nov 24 18:49:40 2014 +0000
drm/i915: Convert 'ring_idle()' to use requests not seqnos
v2 (Chris Wilson):
- Pass current engine seqno to ring_idle() from i915_hangcheck_elapsed() rather
than compute it over again.
- Remove extra whitespace.
Issue: VIZ-5998
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add regressing commit citation provided by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At some point:
commit 2c86c7ca76
Author: Namhyung Kim <namhyung@kernel.org>
Date: Mon Mar 17 18:18:54 2014 -0300
perf report: Merge al->filtered with hist_entry->filtered
We stopped dropping samples for things filtered via the --comms, --dsos,
--symbols, etc, i.e. things marked as filtered in the symbol resolution
routines (thread__find_addr_map(), perf_event__preprocess_sample(),
etc).
But then, in:
commit 268397cb2a
Author: Namhyung Kim <namhyung@kernel.org>
Date: Tue Apr 22 14:49:31 2014 +0900
perf top/tui: Update nr_entries properly after a filter is applied
We don't take into account entries that were filtered in
perf_event__preprocess_sample() and friends, which leads to
inconsistency in the browser seek routines, that expects the number of
hist_entry->filtered entries to match what it thinks is the number of
unfiltered, browsable entries.
So, for instance, when we do:
perf top --symbols ___non_existent_symbol___
the hist_browser__nr_entries() routine thinks there are no filters in
place, uses the hists->nr_entries but all entries are filtered, leading
to a segfault.
Tested with:
perf top --symbols malloc,free --percentage=relative
Freezing, by pressing 'f', at any time and doing the math on the
percentages ends up with 100%, ditto for:
perf top --dsos libpthread-2.20.so,libxul.so --percentage=relative
Both were segfaulting, all fixed now.
More work needed to do away with checking if filters are in place, we
should just use the nr_non_filtered_samples counter, no need to
conditionally use it or hists.nr_filter, as what the browser does is
just show unfiltered stuff. An audit of how it is being accounted is
needed, this is the minimal fix.
Reported-by: Michael Petlan <mpetlan@redhat.com>
Fixes: 268397cb2a ("perf top/tui: Update nr_entries properly after a filter is applied")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-6w01d5q97qk0d64kuojme5in@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull networking fixes from David Miller:
1) Missing list head init in bluetooth hidp session creation, from Tedd
Ho-Jeong An.
2) Don't leak SKB in bridge netfilter error paths, from Florian
Westphal.
3) ipv6 netdevice private leak in netfilter bridging, fixed by Julien
Grall.
4) Fix regression in IP over hamradio bpq encapsulation, from Ralf
Baechle.
5) Fix race between rhashtable resize events and table walks, from Phil
Sutter.
6) Missing validation of IFLA_VF_INFO netlink attributes, fix from
Daniel Borkmann.
7) Missing security layer socket state initialization in tipc code,
from Stephen Smalley.
8) Fix shared IRQ handling in boomerang 3c59x interrupt handler, from
Denys Vlasenko.
9) Missing minor_idr destroy on module unload on macvtap driver, from
Johannes Thumshirn.
10) Various pktgen kernel thread races, from Oleg Nesterov.
11) Fix races that can cause packets to be processed in the backlog even
after a device attached to that SKB has been fully unregistered.
From Julian Anastasov.
12) bcmgenet driver doesn't account packet drops vs. errors properly,
fix from Petri Gynther.
13) Array index validation and off by one fix in DSA layer from Florian
Fainelli
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (66 commits)
can: replace timestamp as unique skb attribute
ARM: dts: dra7x-evm: Prevent glitch on DCAN1 pinmux
can: c_can: Fix default pinmux glitch at init
can: rcar_can: unify error messages
can: rcar_can: print request_irq() error code
can: rcar_can: fix typo in error message
can: rcar_can: print signed IRQ #
can: rcar_can: fix IRQ check
net: dsa: Fix off-by-one in switch address parsing
net: dsa: Test array index before use
net: switchdev: don't abort unsupported operations
net: bcmgenet: fix accounting of packet drops vs errors
cdc_ncm: update specs URL
Doc: z8530book: Fix typo in API-z8530-sync-txdma-open.html
net: inet_diag: always export IPV6_V6ONLY sockopt for listening sockets
bridge: mdb: allow the user to delete mdb entry if there's a querier
net: call rcu_read_lock early in process_backlog
net: do not process device backlog during unregistration
bridge: fix potential crash in __netdev_pick_tx()
net: axienet: Fix devm_ioremap_resource return value check
...
Pull crypto fixes from Herbert Xu:
"This fixes a duplicate dma_unmap_sg call in omap-des and reentrancy
bugs in the powerpc nx driver which may cause bogus output or worse
memory corruption"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: nx - Fix reentrancy bugs
crypto: omap-des - Fix unmapping of dma channels
Linux 4.2-rc1 Commit 0f20972f7b ("dm: factor out a common
cleanup_mapped_device()") moved a common cleanup code to a separate
function. Unfortunately, that commit incorrectly changed the order of
cleanup, so that it destroys the mapped_device's srcu structure
'io_barrier' before destroying its workqueue.
The function that is executed on the workqueue (dm_wq_work) uses the srcu
structure, thus it may use it after being freed. That results in a
crash in the LVM test suite's mirror-vgreduce-removemissing.sh test.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: 0f20972f7b ("dm: factor out a common cleanup_mapped_device()")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When setting yup the symbols library we setup several filter lists,
for dsos, comms, symbols, etc, and there is code that, if there are
filters, do certain operations, like recalculate the number of non
filtered histogram entries in the top/report TUI.
But they were considering just the "Zoom" filters, when they need to
take into account as well the above mentioned filters (perf top --comms,
--dsos, etc).
So store in symbol_conf.has_filter true if any of those filters is in
place.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-f5edfmhq69vfvs1kmikq1wep@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
They just call file_inode and then the corresponding *_inode_file_wait
function. Just make them static inlines instead.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Now that we have file locking helpers that can deal with an inode
instead of a filp, we can change the NFSv4 locking code to use that
instead.
This should fix the case where we have a filp that is closed while flock
or OFD locks are set on it, and the task is signaled so that it doesn't
wait for the LOCKU reply to come in before the filp is freed. At that
point we can end up with a use-after-free with the current code, which
relies on dereferencing the fl_file in the lock request.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reviewed-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Allow callers to pass in an inode instead of a filp.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reviewed-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
...and rename it to better describe how it works.
In order to fix a use-after-free in NFS, we need to be able to remove
locks from an inode after the filp associated with them may have already
been freed. flock_lock_file already only dereferences the filp to get to
the inode, so just change it so the callers do that.
All of the callers already pass in a lock request that has the fl_file
set properly, so we don't need to pass it in individually. With that
change it now only dereferences the filp to get to the inode, so just
push that out to the callers.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reviewed-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
This reverts commit db2efec0ca.
William reported that he was seeing instability with this patch, which
is likely due to the fact that it can cause the kernel to take a new
reference to a filp after the last reference has already been put.
Revert this patch for now, as we'll need to fix this in another way.
Cc: stable@vger.kernel.org
Reported-by: William Dauchy <william@gandi.net>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reviewed-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
If a machine check happens, the machine has the vector facility installed
and the extended save area exists, the cpu will save vector register
contents into the extended save area. This is regardless of control
register 0 contents, which enables and disables the vector facility during
runtime.
On each machine check we should validate the vector registers. The current
code however tries to validate the registers only if the running task is
using vector registers in user space.
However even the current code is broken and causes vector register
corruption on machine checks, if user space uses them:
the prefix area contains a pointer (absolute address) to the machine check
extended save area. In order to save some space the save area was put into
an unused area of the second prefix page.
When validating vector register contents the code uses the absolute address
of the extended save area, which is wrong. Due to prefixing the vector
instructions will then access contents using absolute addresses instead
of real addresses, where the machine stored the contents.
If the above would work there is still the problem that register validition
would only happen if user space uses vector registers. If kernel space uses
them also, this may also lead to vector register content corruption:
if the kernel makes use of vector instructions, but the current running
user space context does not, the machine check handler will validate
floating point registers instead of vector registers.
Given the fact that writing to a floating point register may change the
upper halve of the corresponding vector register, we also experience vector
register corruption in this case.
Fix all of these issues, and always validate vector registers on each
machine check, if the machine has the vector facility installed and the
extended save area is defined.
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The sfpc inline assembly within execve_tail() may incorrectly set bits
28-31 of the sfpc instruction to a value which is not zero.
These bits however are currently unused and therefore should be zero
so we won't get surprised if these bits will be used in the future.
Therefore remove the second operand from the inline assembly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd device driver selects which (alias or base) device is used
for a given requests when the request is build. If the chosen alias
device is set offline before the request gets queued to the device
queue the starting function may use device structures that are
already freed. This might lead to a hanging offline process or a
kernel panic.
Add a check to the starting function that returns the request to the
upper layer if the device is already in offline processing.
In addition to that prevent that an alias device that's already in
offline processing gets chosen as start device.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@linux.vnet.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently instruction_pointer() returns pt_regs->ret and so return value
is of type "long", which implicitly stands for "signed long".
While that's perfectly fine when dealing with 32-bit values if return
value of instruction_pointer() gets assigned to 64-bit variable sign
extension may happen.
And at least in one real use-case it happens already.
In perf_prepare_sample() return value of perf_instruction_pointer()
(which is an alias to instruction_pointer() in case of ARC) is assigned
to (struct perf_sample_data)->ip (which type is "u64").
And what we see if instuction pointer points to user-space application
that in case of ARC lays below 0x8000_0000 "ip" gets set properly with
leading 32 zeros. But if instruction pointer points to kernel address
space that starts from 0x8000_0000 then "ip" is set with 32 leadig
"f"-s. I.e. id instruction_pointer() returns 0x8100_0000, "ip" will be
assigned with 0xffff_ffff__8100_0000. Which is obviously wrong.
In particular that issuse broke output of perf, because perf was unable
to associate addresses like 0xffff_ffff__8100_0000 with anything from
/proc/kallsyms.
That's what we used to see:
----------->8----------
6.27% ls [unknown] [k] 0xffffffff8046c5cc
2.96% ls libuClibc-0.9.34-git.so [.] memcpy
2.25% ls libuClibc-0.9.34-git.so [.] memset
1.66% ls [unknown] [k] 0xffffffff80666536
1.54% ls libuClibc-0.9.34-git.so [.] 0x000224d6
1.18% ls libuClibc-0.9.34-git.so [.] 0x00022472
----------->8----------
With that change perf output looks much better now:
----------->8----------
8.21% ls [kernel.kallsyms] [k] memset
3.52% ls libuClibc-0.9.34-git.so [.] memcpy
2.11% ls libuClibc-0.9.34-git.so [.] malloc
1.88% ls libuClibc-0.9.34-git.so [.] memset
1.64% ls [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
1.41% ls [kernel.kallsyms] [k] __d_lookup_rcu
----------->8----------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-linux-dev@synopsys.com
Cc: stable@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
hardware cursor windows only have some fixed size, and not support
width virtual, when move hardware cursor windows outside of left,
the display would be wrong, so this window can't for cursor now.
And Tag hardware cursor window as a overlay is wrong, will make
userspace wrong behaviour.
So just remove the hardware cursor window
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Window 1 support scale and yuv format, it's waste use it for a
cursor, use window 3 is enough.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Rather than (incompletely [0]) re-implementing drm_gem_mmap() and
drm_gem_mmap_obj() helpers, call them directly from the rockchip mmap
routines.
Once the core functions return successfully, the rockchip mmap routines
can still use dma_mmap_attrs() to simply mmap the entire buffer.
[0] Previously, we were performing the mmap() without first taking a
reference on the underlying gem buffer. This could leak ptes if the gem
object is destroyed while userspace is still holding the mapping.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Add a check for the presence of fb_helper to rockchip_drm_output_poll_changed()
to only call drm_fb_helper_hotplug_event if there is actually a fb_helper
available. Without this check I see NULL pointer dereferences when the
hdmi hotplug irq fires before the fb_helper got initialized.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
VOP can support BGR formats in all windows thanks to red/blue swap option
provided in WINx_CTRL0 registers. This patch enables support for
ABGR8888, XBGR8888, BGR888 and BGR565 formats by using this feature.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJVorxbAAoJEP5prqPJtc/H5zgH/2nvkmT3aQ1gBKdU8L+Ten5D
LIKYyDJ67agNoMfEC/5xWOm7P3X8Qi8cGc326/9AZE22QLE5x6fMCq/SmEC4MA25
GKu2ocwosdPVhIDQOY33IYZHxxtV8UZjt5KdNbQnNO6+iqE6tX5CbgueMlcWusry
WmPCOlezTqHydXo0TYYLPjmqJ66RlrQMWYKvcB0SaxLYQfkBGbkW+fei3wdE4kW1
t7cocRj6Ievv59wCeF+G+fpviTVQVR5bknGA0J3lku9onATOYfdArEAD9FRajygG
KhA/eNr0YEA40VO/baUInuEAJ/YvDqdk9LoyJ1DOXgUv1ysxYSxu/44G/IcZsOU=
=+zVD
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.2-20150712' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-07-12
this is a pull request of 8 patchs for net/master.
Sergei Shtylyov contributes 5 patches for the rcar_can driver, fixing the IRQ
check and several info and error messages. There are two patches by J.D.
Schroeder and Roger Quadros for the c_can driver and dra7x-evm device tree,
which precent a glitch in the DCAN1 pinmux. Oliver Hartkopp provides a better
approach to make the CAN skbs unique, the timestamp is replaced by a counter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ColdFire M5475 on the m5475evb board supports a PCI bus, lets
enable it for the defconfig to get better build and test coverage.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The inb/outb/... family of IO methods end up being multiply defined when
building PCI support for the ColdFire. Compiling gives this:
CC init/main.o
In file included from ./arch/m68k/include/asm/io.h:4:0,
from include/linux/bio.h:30,
from include/linux/blkdev.h:18,
from init/main.c:75:
./arch/m68k/include/asm/io_mm.h:420:0: warning: "inb" redefined
./arch/m68k/include/asm/io_mm.h:108:0: note: this is the location of the previous definition
...
The ColdFire/PCI case defines its own IO access methods, so no others
should be defined or used in this case. Conditionally disable other
definitions that clash with it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Linus Walleij