This modifies hardware flags for powersave to support three different
flags:
* IEEE80211_HW_SUPPORTS_PS - indicates general PS support
* IEEE80211_HW_PS_NULLFUNC_STACK - indicates nullfunc sending in software
* IEEE80211_HW_SUPPORTS_DYNAMIC_PS - indicates dynamic PS on the device
It also adds documentation for all this which explains how to set the
various flags.
Additionally, it fixes a few things:
* a spot where && was used to test flags
* enable CONF_PS only when associated again
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flag ENTRY_TXD_OFDM_RATE isn't flexible enough
to indicate which rate modulation should be used for
a frame. This will become a problem when 11n support
is added.
Remove the flag and replace it with an enum value which
can better indicate the exact rate modulation.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 2 bits in EEPROM_NIC_TX_RX_FIXED each influence
a different antenna. We might as well split the
definition and directly read the correct bit.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restrict drivers to only access link_qual structure during
link tuning. The contents of these fields are for the drivers
and all fields are allowed to be changed to values the driver
considers correct.
This means that some fields need to be moved outside of this
structure to restrict access only to rt2x00link itself.
This allows some code to be moved outside of the rt2x00.h header
and into rt2x00link.c.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The link_tuner() function will always call bbp_read()
at the start of the function. Because this is an
indirect register access has some costs attached
to it (especially for USB hardware).
We already store the value read from the register
into the vgc_level value inside the link structure.
Instead of reading from the register we can read that
field directly and base the tuner on that value.
This reduces the time the registers are locked with
the csr_mutex and speeds up the link_tuner processing.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Listen to IEEE80211_CONF_PS to determine if the device
should drop into powersaving mode. This feature depends
on the dynamic power save functionality in mac80211.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers should notify rt2x00lib when they provide
the IV/ICV data. This adds some flexibility to drivers
which can't provide all information.
* rt2500usb provides ICV inside the frame
* rt2800pci doesn't provide IV/ICV
* rt2800usb doesn't provide IV/ICV
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IV and EIV belong to eachother and don't require
2 seperate fields. Instead they can logically be
merged into a single array with size 2.
With this approach we can simplify the code in
rt2x00crypto.c by using a single memcpy() when
copying the iv/eiv data. Additionally we can
move some code out of if-statements because the
if-statement would always be true.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All code which accessed indirect registers was similar
in respect to the for-loop, the given timeout, etc.
Move it into a seperate function, which for PCI drivers
can be moved into rt2x00pci.
This allows us to cleanup the cleanup the code further
by removing the goto statementsand making the codepath
look a bit nicer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Indirect registers require multiple calls to the CSR
register in order to access the indirect registers.
This must be protected under a lock to prevent race
conditions which could cause invalid data to
be returned when reading from the indirect register or silent
failures when writing data to the indirect register.
USB drivers where already protected under a mutex,
so rename the mutex and make PCI drivers use the mutex
as well.
This now means that BBP and RF registers are no longer
accessible in interrupt context. That is not a bad
situation since the slow behavior of accessing
those registers means we don't _want_ to access them
in interrupt context either.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge the callback functions init_txentry() and
init_rxentry(). This makes life in rt2x00lib a
lot simpler and we can cleanup several functions.
rt2x00pci contained "fake" FIELD definitions for
descriptor words. This is not flexible since it
assumes the driver will always have the same field
to indicate if a driver is available or not.
This should be dependent on the driver, and we
should add a callback function for this.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move calculation of CSR register offset into rt2x00debug.c
and remove the wrapper functions from each individual driver.
(Except rt2500usb, which still needs to wrap for the
different value type argument).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement latest changed from mac80211 configuration
handling to optmize configuration handling in rt2x00.
* Remove set_retry_limit callback function, handled
through config()
* Move config_antenna to its own callback function,
it isn't handled by mac80211 anymore
* Use IEEE80211_CONF_CHANGED_* flags and remove manual
checks
* Removed deprecated short slot setting through config()
and put it in config_erp() through which mac80211 now
configures it
* Remove config_phymode() and move contents to config_erp()
since it only managed the basic rates which is now
determined by mac80211 through config_erp().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few changes to reduce checkpatch.pl errors in the rt2x00 driver. For
the most part, I only fixed cosmetic things, and left the actual 'code
flow' untouched (hopefully)!
Diff is against wireless-testing HEAD.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having a separate callback, use the HW config callback
with a new flag to change retry limits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a crypto key is being removed, rt2x00mac should not
reset the key->hw_key_idx value because that will prevent
the driver from removing the correct key from the hardware.
Furthermore ffz() starts counting at 0 instead of 1, so we don't
need to substract 1 from the resulting value.
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There isn't really a good reason to have the LED
configuration options selectable per driver, lets
make it default 'y' and make it depend on the
NEW_LEDS and LEDS_CLASS interface.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RFKILL should be enabled for _all_ hardware whether
or not they feature a rfkill button or not.
Remove driver specific RFKILL configuration options
and make the rt2x00lib version depend on CONFIG_RFKILL
and defaulting to 'y' to make sure it will always
be enabled when RFKILL was enabled.
This also fixes some bugs where RFKILL wasn't initialized
and didn't respond to RFKILL key presses.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using the PLCP flag to indicate if the
signal value is plcp or the bitrate we should add
a new flag to mark the bitrate type explicitely.
This is usefull when new types are added later for
rt2800.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The txop parameter is supported by rt61pci and rt73usb,
and thus should be written to the register instead
of using the fixed value set during initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the flags should be accessed atomically to
prevent race conditions. The flags that are most important
are those that can change often and indicate the actual
state of the device, queue or queue entry.
The big flag rename was done to move all state flags to
the same naming type as the other rt2x00dev flags and
made sure all places where the flags were used were changed. ;)
Thanks to Stephen for most of the queue flags updates,
which fixes some of the most obvious consequences of the
race conditions. Among those the notorious:
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a module parameter to rt61 and rt73 to disable
HW crypto. The option should only be checked when
determining if the SUPPORT_HW_CRYPTO flag should
be set or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can optimize lna calculation in IRQ context by
calculating most of the value during the config() callback
when most of the value is actually influenced.
This will be required later by rt2800pci and rt2800usb as
well, since they need the lna_gain value during config().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Channel information which is read from EEPROM should
be read into an array containing per-channel information.
This removes the requirement of multiple arrays and makes
the channel handling a bit cleaner and easier to expand.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt61pci supports hardware encryption.
rt61pci supports up to 4 shared keys and up to 64 pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the hardware has indicated the firmware upload has completed
and the device is ready, we should wait another millisecond to
make sure the device is really ready to continue.
Without this timout, bringing the interface down and up again will
fail due to incorrect register initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When IEEE80211_TX_CTL_ASSIGN_SEQ is not set,
the driver should disable hardware sequence counting
to make sure the mac80211 provided counter is used.
This fixes QOS sequence counting, since that is one
of the cases where mac80211 provides a seperate
sequence counter.
By moving the sequence counting code to rt2x00queue
we make sure that _all_ frames get the sequence counter,
including RTS/CTS and Beacon frames.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot this in the previous patch that made it unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new beacon handling from mac80211 we can
reorganize the beacon handling in rt2x00 as well.
This patch will move the function to the TX handlers,
and move all duplicate code into rt2x00queue.c.
After this change the descriptor helper functions
from rt2x00queue.c no longer need to be exported
outside of rt2x00lib and can be declared static.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as init_registers() was called, the rt2400/rt2500
would start raising beacondone interrupts. Since this is highly
premature since no beacons were provided yet, we should
initialize the synchronization register to 0.
This will make all drivers initialize it to 0 regardless
if they are raising beacondone interrupts or not, since it only
makes sense to have it completely disabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a bit of code moving to rt2x00lib within the
TX and RX paths we can now remove a lot of EXPORT_SYMBOL_GPL()
statements. This cleans up the interface between rt2x00lib
and the drivers and has the additional benefit that rt2x00pci
and rt2x00usb are trimmed down in size as well since they
have less to do.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current PCI drivers require a lot of pre-allocated DMA buffers. Reduce this
by using dynamically mapped skb's (using pci_map_single) instead of the pre-
allocated DMA buffers that are allocated at device start-up time.
At the same time move common RX path code into rt2x00lib from rt2x00pci and
rt2x00usb, as the RX paths now are now almost the same.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the same time clean up the device administration a bit, by storing a pointer
to struct device instead of a void pointer that is dependent on the type of
device. The normal PCI and USB subsystem provided macros can be used to convert
the device pointer to the right type.
This makes the rt2x00 driver a bit more type-safe.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The skbs containing the beacons weren't properly cleaned up for rt2400pci, rt2500pci,
rt61pci, and rt73usb. Clean up those skbs in the manner appropriate for each driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The data and data_len fields aren't really necessary in struct
skb_frame_desc, as they can be deduced from the skb itself.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX queues shouldn't be kicked after each frame that is put into the
queue. This could cause problems during RTS and CTS-to-self as well
as with fragmentation. In all those cases you want all frames to be
send out in a single burst. Off course we shouldn't let the queue fill
up entirely, thus we introduce a 10% threshold which, when reached,
will force the frames to be send out regardless of the frame.
In addition we should prevent queues to become full in such a way
that the tx() handler can fail. Instead of stopping the queue when
it is full, we should stop it when it is below the threshold.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce code duplication by moving led structure initialization
into a per-driver function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Reduce goto usage
* Mark if-statements which are true on hardware error unlikely()
* Cleanup debug messages
This makes the code look nicer and be better optimized since
the chance of hardware errors should be very small.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the pending removal of the tx_control structure
we can merge the RX and TX entry private data structure
in advance. This will temporarily increase the required
memory for the queue, but that overhead will only be limited.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the rxdesc structure is properly memsetted before passed to
the driver. This means we don't have to reinitialize the flags
and dev_flags fields in the drivers again.
This will prevent problems when the rxdone handler is adding
flags in a earlier status and will make the code look nicer
when we are adding more read attributes in the rxdone handler
in the driver.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split rt2x00lib_write_tx_desc() up into a TX descriptor initializor
and TX descriptor writer.
This split is required to properly allow mac80211 to move its
tx_control structure into the skb->cb array.
The rt2x00queue_create_tx_descriptor() function will read all tx control
information and convert it into a rt2x00 TX descriptor information structure.
After that function is complete, we have all information we needed from the
tx control structure and are free to start writing into the skb->cb array
for our own purposes.
rt2x00queue_write_tx_descriptor() will be in charge of really sending
the TX descriptor to the hardware and kicking the TX queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation of replacing the statically allocated data DMA buffers with DMA-mapped
skb's we need to change the TXD handling of the PCI drivers, by moving the programming
of the buffer address fields to the actual TXD writing at TX time, instead of at start-up
time.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the integration of the mac80211 multiqueue patches it has become possible that the
mac80211 layer modifies the number of TX queues that is stored inside the ieee80211_hw
structure, especially when multi-queue is not selected.
The rt2x00 drivers are not well suited to handle that situation, as they allocate the
queue structures before mac80211 has modified the number of queues it is going to use,
and also expect the number of allocated queues to match the hardware implementation.
Hence, ensure that rt2x00 maintains by itself the number of queues that the hardware
supports, and, at the same time, making is not dependent on the preservation of contents
inside a mac80211 structure.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the last remaining information details read from ieee80211_tx_control
in the drivers to the txentry_desc structure. After this we can
remove ieee80211_tx_control from the argument list for the callback function,
which makes it easier when the control information is moved into skb->cb
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx_status enumeration was broken since the introduction
of rt61pci. That driver uses different values to report the
status of the tx action.
This would lead to frames that were reported as success but
actually failed to be send out, or frames that were neither
successfull or failure which were reported as failure.
Fix this by change the TX status reporting and more explicitely
check for failure or success. Note that a third possibility is
added "unknown". Not all hardware (USB) can report the actual
TX status, for rt61pci some frames will receive this status
because the TXdone handler is never called for those frames.
This unknown will now be handled as neither success or failure,
so we no longer increment the failure counter while this conclusion
could not be determined from the real status of the frame.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
trying to clean up the signal/noise code. the previous code in mac80211 had
confusing names for the related variables, did not have much definition of
what units of signal and noise were provided and used implicit mechanisms from
the wireless extensions.
this patch introduces hardware capability flags to let the hardware specify
clearly if it can provide signal and noise level values and which units it can
provide. this also anticipates possible new units like RCPI in the future.
for signal:
IEEE80211_HW_SIGNAL_UNSPEC - unspecified, unknown, hw specific
IEEE80211_HW_SIGNAL_DB - dB difference to unspecified reference point
IEEE80211_HW_SIGNAL_DBM - dBm, difference to 1mW
for noise we currently only have dBm:
IEEE80211_HW_NOISE_DBM - dBm, difference to 1mW
if IEEE80211_HW_SIGNAL_UNSPEC or IEEE80211_HW_SIGNAL_DB is used the driver has
to provide the maximum value (max_signal) it reports in order for applications
to make sense of the signal values.
i tried my best to find out for each driver what it can provide and update it
but i'm not sure (?) for some of them and used the more conservative guess in
doubt. this can be fixed easily after this patch has been merged by changing
the hardware flags of the driver.
DRIVER SIGNAL MAX NOISE QUAL
-----------------------------------------------------------------
adm8211 unspec(?) 100 n/a missing
at76_usb unspec(?) (?) unused missing
ath5k dBm dBm percent rssi
b43legacy dBm dBm percent jssi(?)
b43 dBm dBm percent jssi(?)
iwl-3945 dBm dBm percent snr+more
iwl-4965 dBm dBm percent snr+more
p54 unspec 127 n/a missing
rt2x00 dBm n/a percent rssi+tx/rx frame success
rt2400 dBm n/a
rt2500pci dBm n/a
rt2500usb dBm n/a
rt61pci dBm n/a
rt73usb dBm n/a
rtl8180 unspec(?) 65 n/a (?)
rtl8187 unspec(?) 65 (?) noise(?)
zd1211 dB(?) 100 n/a percent
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00pci allocates DMA for descriptor and data,
rt61pci doesn't use this for the beacon, but it can
use the descriptor part as temporary buffer instead
of using pskb_expand_head().
Using this temporary buffer is obviously much better
then reallocating the skb buffer...
At the same time we can set the data length for the
beacon queue at 0, to make sure no DMA is allocated for
data (but just for the descriptor).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the rt2x00 queue enumeration as much as possible,
removing the usage of the mac80211 queue numbering
wherever it is possible.
This makes it easier for mac80211 to change it queue
identification scheme without having to deal with
big changes in the rt2x00 code.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was an obvious typo in LED structure
initialization which caused the radio and quality/activity
leds to be incorrectly initialized which resulted in
the leds not being enabled.
Additionally add the rt2x00led_led_activity() handler
that will enable TX/RX activity leds when the radio
is being enabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The layer above will free the skb in an error case.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement triggers inside rt2x00 itself based
on input from mac80211. This replaces the method
of using the mac80211 trigger events which do
not work for USB drivers due to the scheduling
requirement.
After this patch RT2500USB_LEDS and RT73USB_LEDS
no longer need to be tagged as broken since they
now support LED handling again without having to
check for in_atomic().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TO_DS filter does not only depend on the FIF_PROMISC_IN_BSS flag
provided by mac80211, but also on the intf_ap_count count.
This makes sense, since when Master mode is active, we should all frames
that are send to the active AP (the device itself).
This means that when an interface is added we should force the
packet filter to be updated during the next mac80211 call of
configure_filter() to make sure the intf_ap_count field is checked.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt73usb and rt2500usb used in_atomic to determine
if a configuration step should be rescheduled or not.
Since in_atomic() is not a valid method to determine
if sleeping is allowed we should fix the way this is handled
by adding a new flag to rt2x00.
In addition mark LED class support for the drivers broken
since that also uses the broken in_atomic() method but
so far no solution exists to have LED triggers work only
in scheduled context.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rxdone_entry_desc structure contains 3 fields
which are always 1 or 0. We can safe 8 bytes by
replacing them with a single dev_flags fields which
contain the flags for those settings.
Additionally we can remove the OFDM flag since it
is no longer used since the introduction of the
SIGNAL_PLCP flag.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After sampling hundreds of RX frame descriptors,
the results were conclusive:
- The Ralink documentation regarding the SIGNAL and RSSI are wrong.
It turns out that of the 5 BBR registers, we should not use BBR0 and BBR1
for SIGNAL and RSSI respectively, but actually BBR1 and BBR2.
BBR0 does show values, but the exact meaning remains unclear,
but they cannot be translated into a SIGNAL or RSSI field.
BBR3, BBR4 and BBR5 are always 0, so their meaning is unknown.
As it turns out, the reported SIGNAL is the PLCP value, this
in contradiction to what was expected looking at rt2500pci which
only reported the PLCP values for OFDM rates and bitrate values
for CCK rates.
This means we should let the driver raise the flag about the contents
of the SIGNAL field so rt2x00lib can always do the right thing based
on what the driver reports.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whatever mode we are in, according to the legacy drivers
we should always enable TSF ticking/counting.
We should also always enable the TBCN/TBTT field,
this field is only disabled during beacon regeneration.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename config_preamble() to config_erp() and cleanup argument
list by putting it all into a single structure.
This will make the function more meaningful and easier to
expand later. This second option is mostly intended to make
the patch "mac80211: proper short-slot handling" from Johannes Berg
easier to apply for rt2x00.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib should filter SW diversity out before sending any configuration
changes to the driver. When rt2x00lib fails to do this, it is important
that such events are reported because it _must_ be fixed.
So upgrading the error level to a BUG_ON() which will make sure
this bug gets noticed whenever it happens.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib depended on 2 crc algorithms because rt61/rt73
use a different algorithm then rt2800. This means that
even when only 1 algorithm was needed, the dependency was
still present for both.
By moving the checksum generation to the driver we can clean
up 2 annoying flags (which indicated which checksum was required)
and move the dependency to where it belongs: the driver.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should not write 0 to the beacon sync register during
config_intf() since that will clear out the beacon interval
and forces the beacon to be send out at the lowest interval.
(reported by Mattias Nissler).
The side effect of the same bug was that while working with
multiple virtual AP interfaces a change for any of those
interfaces would disable beaconing untill an beacon update
was provided.
This is resolved by only updating the TSF_SYNC value during
config_intf(). In update_beacon() we disable beaconing
temporarily to prevent fake beacons to be transmitted.
Finally kick_tx_queue() will enable beaconing again.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On rt73 and rt61 disabling reception of multicast packets also disables
broadcast traffic which we never want to do. Therefore we should never
disable multicast.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a typo in the link tuner where accidently the
2GHz band was checked instead of the 5GHz band.
This forced the link tuner to work in an invalid
range for the currently active band.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't wildly pass any number for num_rates to rt2x00lib,
instead pass which type of rates are supported (CCK, OFDM).
Same for num_modes but then for the 2GHZ and 5GHZ band.
This makes the interface look much nicer and makes
extending it later easier.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specifications indicate the TSF registers are read-only,
so there is no point in writing 0 to those registers.
As far as I know there isn't another way to reset the
TSF registers. So removing these callbacks will notify
mac80211 about the lack of support.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As Adam Baker reported the DMA address for the
descriptor base was incorrectly initialized in
the PCI drivers.
Instead of the DMA base for the descriptor, the
DMA base for the data was passed resulting in a
broken TX/RX state for PCI drivers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ACK_CTS frame is a control frame, this means
dropping the frame depends on the FIF_CONTROL flag
for filtering.
This also fixes an obvious typo in register definition.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a new flag for the skb_frame_desc structure which is used to tag
rts/cts frames that are generated by the driver. Through the tag we can
recognize frames we have generated ourselves, so we don't report their tx
status to mac80211.
This patch is based on the original patch by
Mattias Nissler <mattias.nissler@gmx.de>.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 sends the txpower to use during config(),
we already store it in the rt2x00_dev structure.
When writing the descriptor correctly initialize
the txpower field with this value to make sure
all frames are send out with the correct tx power.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The second eeprom recovery message is about
the RSSI offset for ieee802.11 A.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the last remnants of the MGMT ring initialization
from rt61pci.ko
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the debug messages regarding initialization from
EEPROM. The values are vendor specific, and are not really
needed for debug purposes. If they ever become usefull we
still have access to them through debugfs which also
prints the exact same values...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of the led triggers provided by mac80211 to control
the led status. This can be enabled through a per-driver
configuration option which will automatically enable the
generic handler in rt2x00lib.
This has been enabled for rt2500usb and rt73usb for the moment
since the led class will call set_brightness in irq context which
will not work correctly with the usb drivers who need to sleep.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As Johannes Berg indicated the BEACON and AFTER_BEACON
queue indeces in mac80211 should be removed because they
are too hardware specific. This patch adds the queue index
defines into rt2x00queue.h and removes the dependency of
the defines inside mac80211.h.
Also move rt2x00pci_beacon_update() into rt2400pci and
rt2500pci individually since it is no longer a generic
function since rt61 and rt2800 no longer use that.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt73usb doesn't have a 5th queue, correctly initialize hw->queues
rt61pci had a 5th queue but was removed recently, correctly initialize
hw->queues and remove the last remnants.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework the interface handling. Delete the interface structure
and replace it with a per-interface structure. This changes the
way rt2x00 handles the active interface drastically.
Copy ieee80211_bss_conf to the this rt2x00_intf structure during
the bss_info_changed() callback function. This will allow us to
reference it later, and removes the requirement for the device flag
SHORT_PREAMBLE flag which is interface specific.
Drivers receive the option to give the maximum number of virtual
interfaces the device can handle. Virtual interface support:
rt2400pci: 1 sta or 1 ap, * monitor interfaces
rt2500pci: 1 sta or 1 ap, * monitor interfaces
rt2500usb: 1 sta or 1 ap, * monitor interfaces
rt61pci: 1 sta or 4 ap, * monitor interfaces
rt73usb: 1 sta or 4 ap, * monitor interfaces
At the moment none of the drivers support AP and STA interfaces
simultaneously, this is a hardware limitation so future support
will be very unlikely.
Each interface structure receives its dedicated beacon entry,
with this we can easily work with beaconing while multiple master
mode interfaces are currently active.
The configuration handlers for the MAC, BSSID and type are
often called together since they all belong to the interface
configuration. Merge the 3 configuration calls and cleanup
the API between rt2x00lib and the drivers. While we are cleaning
up the interface configuration anyway, we might as well clean up
the configuration handler as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver should select what CRC algorithm is required
when performing a checksum on the firmware.
rt61pci & rt73usb require crc-itu-t
rt2800pci & rt2800usb require crc-ccitt
Legacy 2800pci/usb driver uses crc-itu-t + bit order reversion,
but that is just inefficient especially since the end result is
the same as a different algorithm which is also available as library. ;)
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The space allocated in the skb for a descriptor is only 24 bytes when
setting up beacons in rt61 so make sure we don't write to the descriptor
words beyond that and corrupt the beacon packet.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This introduces a big queue handling overhaul, this also
renames "ring" to "queues".
Move queue handling into rt2x00queue.c and the matching header,
use Kerneldoc to improve rt2x00 library documentation.
Access to the queues is now protected under a spinlock, this
to prevent race conditions which could corrupt the indexing
system of the queue.
Each queue entry allocates x bytes for driver/device specific data,
this cleans up the queue structure significantly and improves
code readability.
rt2500usb no longer needs 2 entries in the beacon queue to correctly
send out the guardian byte. This is now handled in the entry specific
structure.
rt61 and rt73 now use the correct descriptor size for beacon frames,
since this data is written into the registers not the entire TXD
descriptor was used but instead of a subset of it named TXINFO.
Finally this also fixes numerous other bugs related to incorrect
beacon handling or beacon related code.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds 2 new states which both are used to toggle
the RX. These new states are required for usage
inside the link tuner thread, because the normal
RX toggling will stop the link tuner thread.
While it is possible that the link tuner thread itself
is the caller of the RX toggle (when using software
antenna diversity).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A subtle merge error was introduced after re-queueing a patch for 2.6.24
instead of 2.6.25...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (based on Ron Rindjunsky's) creates a framework for
a unified way to pass BSS configuration to drivers that require
the information, e.g. for implementing power save mode.
This patch introduces new ieee80211_bss_conf structure that is
passed to the driver via the new bss_info_changed() callback
when the BSS configuration changes.
This new BSS configuration infrastructure adds the following
new features:
* drivers are notified of their association AID
* drivers are notified of association status
and replaces the erp_ie_changed() callback. The patch also does
the relevant driver updates for the latter change.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prior to enabling the radio rt2x00lib should go through all
rings and for each entry should call the callback function
init_txentry() and init_rxentry().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the MY_BSS descriptor field to determine if the
received frame belongs to the same BSS as the interface.
This can be used by rxdone to determine if the frame
should be updated or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send the skb structure with write_tx_desc() and use
the skbdesc structure to read all information about
the frame. This saves several arguments in the function
definition and it is easier to send more information
later as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The packet filter flags don't belong in the interface structure
because they are device based instead of interface based.
So move the filter fields out of struct interface and into rt2x00_dev.
Additionally we shouldn't change the filter based on the working
mode, if such a thing is needed than mac80211 should have done that.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Store the queue idx inside structure data_ring
Store the entry idx inside structure data_entry
This saves us a few calls to ARRAY_INDEX() which is now unused.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These flags used to be fixed to one in rt2500pci_config_type, which
caused the beacon timer interrupt to fire. This would lead to
rt2x00lib_beacondone adding work which called
rt2x00lib_beacondone_scheduled which called ieee80211_beacon_get which
printed an error about not having any beacon data.
With this patch, these interrupts are only generated when the interface
is configured to send beacons.
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the skb->cb field to add a frame description that can be used
to transfer information passed each rt2x00 layer. This reduces the
required arguments for rt2x00lib_write_tx_desc().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DRV_NAME was always set to the KBUILD_MODNAME value,
lets clean everything up by removing DRV_NAME and just
use KBUILD_MODNAME directly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2400pci, rt2500pci and rt61 require different
txdone handling, but the code that pushes the frame
upstream and cleans up the entry is identical to
all of them.
This will create the function rt2x00pci_txdone()
to remove the duplicate code.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a flag to struct txdata_entry_desc that specifies whether an ack for the
frame is to be expected. Use this flag to set the ACK bit in the tx descriptor.
Previously, the ACK bit could be set incorrectly on CTS-to-self frames, so they
caused retries and were reported to be failed in the txdone handlers.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coverty indicated that data_desc with a single
element array is bad coding style. This removes
the structure and forces everybody to use __le32.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the updated antenna setup the following
variables are no longer used.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes rt61 antenna selection again. It helps at least with the
rt61 pci card in my box, I hope I haven't broken behaviour on other RF chips.
RF 2529 antenna setup is incomplete, we need to at code for diversity when we
figure out how it is done properly.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some register accesses need rt2x00dev to be non-const
they all need modifying so the prototype is consistent.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on investigation of the legacy drivers, I have made the
following assumptions of the antenna setup:
- R77 is the TX antenna configuration
- RF2529 fetches default antenna selection from NIC eeprom word
With these assumptions we can change the antenna configuration
to correctly read both antenna setup values and correctly
configure the antenna. And we can now also configure the antenna
for RF2529 without a double antenna.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup if-statements for simple 1/0 register field values.
This also fixes a endian bug in rt2500usb when working
with the PHY_CSR2 initialization. As well as a bug
in the enabling of the LED in rt73usb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although ANTENNA_SW_DIVERSITY should never be send
to the driver, we should still handle it to prevent bugs.
But instead of defaulting to ANTENNA_HW_DIVERSITY we
should default to ANTENNA_B instead.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 has 3 values for the antenna setup:
0 - default
1 - use antenna 1
2 - use antenna 2
This means that rt2x00 should store the default value
from the EEPROM somwhere and use that when mac80211 indicates
that the antenna setup is 0.
This also implies that rt2x00 should no longer write the
hw->config.antenna_sel_* values based on the EEPROM input.
This also adds the basis in rt2x00lib for correct software
diversity handling. By default rt2x00lib will now configure
antenna B instead of hardware diversity.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the default EEPROM values use
the values from the enums instead of "magic" values.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all link quality statistics variables into
the link_qual structure. This cleans up the link
structure and allows us to use it for more then
just statistics.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes it happens in the tx path that an entry given to the hardware isn't
reported in the txdone handler. This ultimately led to the dreaded "non-free
entry in the non-full queue" message and the stopping of the tx queue. Work
around this issue by allowing the driver to also clear out previos entries in
the txdone handler.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When skb_push() is used we should memset the memory before
usage. This will prevent bugs which could occur when the
data is treated as TX descriptor.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reorganize configuration handling by creating a extra
structure which contains precalculated values based
on the mac80211 values which are usefull for all
individual drivers.
This also fixes the preamble configuration problem,
up untill now preamble was never configured since
by default the rate->val value was used when changing
the mode.
Now rate->val will only be used to set the basic rate mask.
The preamble configuration will now be done correctly
through the erp_ie_changed callback function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make some small optimizations by removing
some simple if-statements.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt61pci contained 1 line of 88 characters width,
this needs to be cut down.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All drivers use the same values for TSF sync,
this will move the value determination into rt2x00config.c,
and the definition for the values to rt2x00reg.h
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported by Modestas Vainius, enabling rkfill in 1 driver and
disabling it in a second could cause a NULL pointer exception when
the rfkill-disabled driver still sets the CONFIG_SUPPORT_HW_BUTTON flag.
Furthermore, rfkill expects the timeout as a value in milliseconds
instead of jiffies. Also increase the timeout to a second,
since this 250ms would be overkill.
Also the flag DEVICE_ENABLED_RADIO_HW is causing problems
for devices which do not support the hardware button
while rfkill is enabled in the driver.
To remidy this we should inverse the flag and its meaning,
rename the flag to DEVICE_DISABLED_RADIO_HW this means that
by default the radio is enabled by the hardware button (if present)
and can only be disabled explicitely.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We shouldn't use changed_flags when configuring the packet filter,
we work directly with the total_flags which is safe enough since
we already check if something has changed after we applied our
packet filtering flag rules.
Also make sure that when the packet filter is scheduled, the
rt2x00dev->interface.filter is cleared to make sure the drivers
will update the packet filter instead of failing at the check:
*total_flags == rt2x00dev->interface.filter
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various drivers contained duplicate code to handle the
MAC and BSSID initialization correctly. This moves the
address copy to little endian variables to rt2x00config.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Modestas Vainius <modestas@vainius.eu>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00dev->flags has become a chaos over time,
this will reorganize the flags by renaming, deleting, adding
and properly implement the flags.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make rt61pci_beacon_update and rt73usb_beacon_update static,
they are only used inside their own source file and then only
for setting it as callback funtion for mac80211.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.
This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.
Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.
At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().
The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.
Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn