The enable function was using the global timeout variable for local operations.
This resulted in the value of the global variable being corrupted, thus
breaking the code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
On platforms with no iCRU support don't print two, (possibly conflicting),
"NMI occurred" messages when the firmware is unable to source the NMI.
Please note that one of the enhancements to the v1.3.0 hpwdt driver is to panic and allow
KDUMP to succeed even on NMIs that are unknown to the platform firmware.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the passed watchdog_device instead of the static global variable when
testing and setting the status in watchdog_ping, watchdog_start, and
watchdog_stop. Note that the callers of these functions are actually
passing the static global variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We want to enable dithering on any pipe where the frame buffer has
more color resolution than the output device.
The previous code was incorrectly clamping the frame buffer bpc to the
display bpc, effectively disabling dithering all of the time as the
computed frame buffer bpc would never be larger than the display bpc.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
* 'irq-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
x86, iommu: Mark DMAR IRQ as non-threaded
genirq: Make irq_shutdown() symmetric vs. irq_startup again
When a xHC host is unable to handle isochronous transfer in the
interval, it reports a Missed Service Error event and skips some tds.
Currently xhci driver handles MSE event in the following ways:
1. When encounter a MSE event, set ep->skip flag, update event ring
dequeue pointer and return.
2. When encounter the next event on this ep, the driver will run the
do-while loop, fetch td from ep's td_list to find the td
corresponding to this event. All tds missed are marked as short
transfer(-EXDEV).
The do-while loop will end in two ways:
1. If the td pointed by the event trb is found;
2. If the ep ring's td_list is empty.
However, if a buggy HW reports some unpredicted event (for example, an
overrun event following a MSE event while the ep ring is actually not
empty), the driver will never find the td, and it will loop until the
td_list is empty.
Unfortunately, the spinlock is dropped when give back a urb in the
do-while loop. During the spinlock released period, the class driver
may still submit urbs and add tds to the td_list. This may cause
disaster, since the td_list will never be empty and the loop never ends,
and the system hangs.
To fix this, count the number of TDs on the ep ring before skipping TDs,
and quit the loop when skipped that number of tds. This guarantees the
do-while loop will end after certain number of cycles, and driver will
not be trapped in an infinite loop.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes, when a USB 3.0 device is disconnected, the Intel Panther
Point xHCI host controller will report a link state change with the
state set to "SS.Inactive". This causes the xHCI host controller to
issue a warm port reset, which doesn't finish before the USB core times
out while waiting for it to complete.
When the warm port reset does complete, and the xHC gives back a port
status change event, the xHCI driver kicks khubd. However, it fails to
set the bit indicating there is a change event for that port because the
logic in xhci-hub.c doesn't check for the warm port reset bit.
After that, the warm port status change bit is never cleared by the USB
core, and the xHC stops reporting port status change bits. (The xHCI
spec says it shouldn't report more port events until all change bits are
cleared.) This means any port changes when a new device is connected
will never be reported, and the port will seem "dead" until the xHCI
driver is unloaded and reloaded, or the computer is rebooted. Fix this
by making the xHCI driver set the port change bit when a warm port reset
change bit is set.
A better solution would be to make the USB core handle warm port reset
in differently, merging the current code with the standard port reset
code that does an incremental backoff on the timeout, and tries to
complete the port reset two more times before giving up. That more
complicated fix will be merged next window, and this fix will be
backported to stable.
This should be backported to kernels as old as 3.0, since that was the
first kernel with commit a11496ebf3 ("xHCI: warm reset support").
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix build when CONFIG_ISA_DMA_API is enabled but
CONFIG_COMEDI_PCI[_DRIVERS] is not enabled.
Fixes these build errors:
drivers/staging/comedi/drivers/ni_labpc.c: In function 'labpc_ai_cmd':
drivers/staging/comedi/drivers/ni_labpc.c:1351: error: implicit declaration of function 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c: At top level:
drivers/staging/comedi/drivers/ni_labpc.c:1802: error: conflicting types for 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c:1351: note: previous implicit declaration of 'labpc_suggest_transfer_size' was here
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In ad-hoc mode, driver b43 does not issue beacons.
Signed-off-by: Manual Munz <freifunk@somakoma.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: Make GPU/CPU page size handling consistent in blit code (v2)
drm/radeon/kms: fix typo in r100_blit_copy
drm/radeon: Unreference GEM object outside of spinlock in page flip error path.
drm/radeon: Don't read from CP ring write pointer registers.
drm/ttm: request zeroed system memory pages for new TT buffer objects
* 'for-linus' of git://git.infradead.org/users/sameo/mfd-2.6:
mfd: Fix omap-usb-host build failure
mfd: Make omap-usb-host TLL mode work again
mfd: Set MAX8997 irq pointer
mfd: Fix initialisation of tps65910 interrupts
mfd: Check for twl4030-madc NULL pointer
mfd: Copy the device pointer to the twl4030-madc structure
mfd: Rename wm8350 static gpio_set_debounce()
mfd: Fix value of WM8994_CONFIGURE_GPIO
The BO blit code inconsistenly handled the page size. This wasn't
an issue on system with 4k pages since the GPU's page size is 4k as
well. Switch the driver blit callbacks to take num pages in GPU
page units.
Fixes lemote mipsel systems using AMD rs780/rs880 chipsets.
v2: incorporate suggestions from Michel.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
cur_pages is the number of pages per loop iteration.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://github.com/davem330/net: (62 commits)
ipv6: don't use inetpeer to store metrics for routes.
can: ti_hecc: include linux/io.h
IRDA: Fix global type conflicts in net/irda/irsysctl.c v2
net: Handle different key sizes between address families in flow cache
net: Align AF-specific flowi structs to long
ipv4: Fix fib_info->fib_metrics leak
caif: fix a potential NULL dereference
sctp: deal with multiple COOKIE_ECHO chunks
ibmveth: Fix checksum offload failure handling
ibmveth: Checksum offload is always disabled
ibmveth: Fix issue with DMA mapping failure
ibmveth: Fix DMA unmap error
pch_gbe: support ML7831 IOH
pch_gbe: added the process of FIFO over run error
pch_gbe: fixed the issue which receives an unnecessary packet.
sfc: Use 64-bit writes for TX push where possible
Revert "sfc: Use write-combining to reduce TX latency" and follow-ups
bnx2x: Fix ethtool advertisement
bnx2x: Fix 578xx link LED
bnx2x: Fix XMAC loopback test
...
* '3.1-rc-fixes' of git://linux-iscsi.org/target-pending:
iscsi-target: Fix sendpage breakage with proper padding+DataDigest iovec offsets
iscsi-target: Disable markers + remove dangerous local scope array usage
target: Skip non hex characters for VPD=0x83 NAA IEEE Registered Extended
tcm_fc: Work queue based approach instead of managing own thread and event based mechanism
tcm_fc: Invalidation of DDP context for FCoE target in error conditions
target: Fix race between multiple invocations of target_qf_do_work()
Today I noticed that the usb bluetooth adapter (BCM2046B1) on my 2011
mac mini was not working. I've created a patch to get it going.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch against current git adds the hardware ID for the Apple
MacBookAir4,1, released in July 2011. The device features a BCM2046
USB chip. The patch was inspired by the previous modifications adding
support for the MacBookAir3,x.
Signed-off-by: Pieter-Augustijn Van Malleghem <p-a@scarlet.be>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reordered the BT ST channel registration, to make sure that the
event channel is registered before all others. This prevents a
situation where incoming events may cause kernel panic in the ST
driver if the event channel is not yet registered to handle
incoming events.In addition, the deregistration of the channels
was also modified, to be in the reversed order of the registration,
to allow the event channel to be the last one unregistered.
Signed-off-by: Chen Ganir <chen.ganir@ti.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The TBI bit in PHYStatus is reserved on anything but the oldest 8169.
Nobody complained after I disabled it for the 8168 and the 810x (see
66ec5d4fb1).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
This patch fixes a bug in the iscsit_fe_sendpage_sg() transmit codepath that
was originally introduced with the v3.1 iscsi-target merge that incorrectly
uses hardcoded cmd->iov_data_count values to determine cmd->iov_data[] offsets
for extra outgoing padding and DataDigest payload vectors.
This code is obviously incorrect for the DataDigest enabled case with sendpage
offload, and this fix ensures correct operation for padding + DataDigest,
padding only, and DataDigest only cases. The bug was introduced during a
pre-merge change in iscsit_fe_sendpage_sg() to natively use struct scatterlist
instead of the legacy v3.0 struct se_mem logic.
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This fixes a build breakage for OMAP3 boards.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: netdev@vger.kernel.org
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/801719 .
An O2Micro PCI Express FireWire controller,
"FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Device [1217:11f7] (rev 05)"
which is a combination device together with an SDHCI controller and some
sort of storage controller, misses SBP-2 status writes from an attached
FireWire HDD. This problem goes away if MSI is disabled for this
FireWire controller.
The device reportedly does not require QUIRK_CYCLE_TIMER.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (amended changelog)
Cc: <stable@kernel.org>
This patch makes iscsi-target explictly disable OFMarker=Yes and IFMarker=yes
parameter key usage during iscsi login by setting IFMarkInt_Reject and
OFMarkInt_Reject values in iscsi_enforce_integrity_rules() to effectively
disable iscsi marker usage. With this patch, an initiator proposer asking
to enable either marker parameter keys will be issued a 'No' response, and
the target sets OFMarkInt + IFMarkInt parameter key response to 'Irrelevant'.
With markers disabled during iscsi login, this patch removes the problematic
on-stack local-scope array for marker intervals in iscsit_do_rx_data() +
iscsit_do_tx_data(), and other related marker code in iscsi_target_util.c.
This fixes a potentional stack smashing scenario with small range markers
enabled and a large MRDSL as reported by DanC here:
[bug report] target: stack can be smashed
http://www.spinics.net/lists/target-devel/msg00453.html
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds target_parse_naa_6h_vendor_specific() to address a bug where the
conversion of PRODUCT SERIAL NUMBER to use hex2bin() in target_emulate_evpd_83()
was not doing proper isxdigit() checking. This conversion of the vpd_unit_serial
configifs attribute is done while generating a VPD=0x83 NAA IEEE Registered
Extended DESIGNATOR format's 100 bits of unique VENDOR SPECIFIC IDENTIFIER +
VENDOR SPECIFIC IDENTIFIER EXTENSION area.
This patch allows vpd_unit_serial (VPD=0x80) and the T10 Vendor ID DESIGNATOR
format (VPD=0x83) to continue to use free-form variable length ASCII values,
and now skips any non hex characters for fixed length NAA IEEE Registered Extended
DESIGNATOR format (VPD=0x83) requring the binary conversion.
This was originally reported by Martin after the v3.1-rc1 change to use hex2bin()
in commit 11650b8596 where the use of non hex
characters in vpd_unit_serial generated different values than the original
v3.0 internal hex -> binary code. This v3.1 change caused a problem with
filesystems who write a NAA DESIGNATOR onto it's ondisk metadata, and this patch
will (again) change existing values to ensure that non hex characters are not
included in the fixed length NAA DESIGNATOR.
Note this patch still expects vpd_unit_serial to be set via existing userspace
methods of uuid generation, and does not do strict formatting via configfs input.
The original bug report and thread can be found here:
NAA breakage
http://www.spinics.net/lists/target-devel/msg00477.html
The v3.1-rc1 formatting of VPD=0x83 w/o this patch:
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 20
designator_type: NAA, code_set: Binary
associated with the addressed logical unit
NAA 6, IEEE Company_id: 0x1405
Vendor Specific Identifier: 0xffde35ebf
Vendor Specific Identifier Extension: 0x3092f498ffa820f9
[0x6001405ffde35ebf3092f498ffa820f9]
Designation descriptor number 2, descriptor length: 56
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: LIO-ORG
vendor specific: IBLOCK:ffde35ec-3092-4980-a820-917636ca54f1
The v3.1-final formatting of VPD=0x83 w/ this patch:
VPD INQUIRY: Device Identification page
Designation descriptor number 1, descriptor length: 20
designator_type: NAA, code_set: Binary
associated with the addressed logical unit
NAA 6, IEEE Company_id: 0x1405
Vendor Specific Identifier: 0xffde35ec3
Vendor Specific Identifier Extension: 0x924980a82091763
[0x6001405ffde35ec30924980a82091763]
Designation descriptor number 2, descriptor length: 56
designator_type: T10 vendor identification, code_set: ASCII
associated with the addressed logical unit
vendor id: LIO-ORG
vendor specific: IBLOCK:ffde35ec-3092-4980-a820-917636ca54f1
(v2: Fix parsing code to dereference + check for string terminator instead
of null pointer to ensure a zeroed payload for vpd_unit_serial less
than 100 bits of NAA DESIGNATOR VENDOR SPECIFIC area. Also, remove
the unnecessary bitwise assignment)
Reported-by: Martin Svec <martin.svec@zoner.cz>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch reverts commit 9b76883284 which
was introduced in 2.6.38-rc1. It works around a problem where the iwlagn
driver stimulates a bug crashing (requiring power cycle to recover) some
APs under heavy traffic.
CC: stable@kernel.org #2.6.39, #3.0.0 #3.1.0
Signed-off-by: Don Fry <donald.h.fry@intel.com>
SIgned-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The eeprom data is stored in little-endian order in the rt2x00 library.
As it was converted to cpu order in the read routines, the data need to
be converted to LE on a big-endian platform.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using gcc 4.4.5 on a Powerbook G4 with a PPC cpu, a complicated
if statement results in incorrect flow, whereas the equivalent switch
statement works correctly.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix regression introduced by:
commit: ecb4433550
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Aug 12 14:00:59 2011 +0200
mac80211: fix suspend/resume races with unregister hw
Above commit add rtnl_lock() into wiphy_register(), what cause deadlock
when initializing ipw2x00 driver, which itself call wiphy_register()
from register_netdev() internal callback with rtnl mutex taken.
To fix move wiphy_register() outside register_netdev(). This solution
have side effect of not creating /sys/class/net/wlanX/phy80211 link,
but that's a minor issue we can live with.
Bisected-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Bisected-by: Michael Witten <mfwitten@gmail.com>
Tested-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Tested-by: Michael Witten <mfwitten@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a number of issues in ibmveth_set_csum_offload:
- set_attr6 and clr_attr6 may be used uninitialised
- We store the result of the IPV4 checksum change in ret but overwrite
it in a couple of places before checking it again later. Add ret4
to make it obvious what we are doing.
- We weren't clearing the NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM flags
if the enable of that hypervisor feature failed.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b9367bf3ee (net: ibmveth: convert to hw_features) reversed
a check in ibmveth_set_csum_offload that results in checksum offload
never being enabled.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: David S. Miller <davem@davemloft.net>
descs[].fields.address is 32bit which truncates any dma mapping
errors so dma_mapping_error() fails to catch it.
Use a dma_addr_t to do the comparison. With this patch I was able
to transfer many gigabytes of data with IOMMU fault injection set
at 10% probability.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # v2.6.37+
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6e8ab30ec6 (ibmveth: Add scatter-gather support) introduced a
DMA mapping API inconsistency resulting in dma_unmap_page getting
called on memory mapped via dma_map_single. This was seen when
CONFIG_DMA_API_DEBUG was enabled. Fix up this API usage inconsistency.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> # v2.6.37+
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'stable/bug.fixes' of git://oss.oracle.com/git/kwilk/xen:
xen/i386: follow-up to "replace order-based range checking of M2P table by linear one"
xen/irq: Alter the locking to use a mutex instead of a spinlock.
xen/e820: if there is no dom0_mem=, don't tweak extra_pages.
xen: disable PV spinlocks on HVM
Problem: Changed from wake_up_interruptible -> wake_up_process and
wait_event_interruptible-> schedule_timeout_interruptible broke the FCoE
target. Earlier approach of wake_up_interruptible was also looking at
'queue_cnt' which is not necessary, because it increment of 'queue_cnt'
with wake_up_inetrriptible / waker_up_process introduces race condition.
Fix: Instead of fixing the code which used wake_up_process and remove
'queue_cnt', using work_queue based approach is cleaner and acheives
same result. As well, work queue based approach has less programming
overhead and OS manages threads which processes work queues.
This patch is developed by Christoph Hellwig and reviwed+validated by
Kiran Patil.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Problem: HW DDP context wasn;t invalidated in case of ABORTS, etc...
This leads to the problem where memory pages which are used for DDP
as user descriptor could get reused for some other purpose (such as to
satisfy new memory allocation request either by kernel or user mode threads)
and since HW DDP context was not invalidated, HW continue to write to
those pages, hence causing memory corruption.
Fix: Either on incoming ABORTS or due to exchange time out, allowed the
target to cleanup HW DDP context if it was setup for respective ft_cmd.
Added new function to perform this cleanup, furthur it can be enhanced
for other cleanup activity.
Additinal Notes: To avoid calling ddp_done from multiple places, composed
the functionality in helper function "ft_invl_hw_context" and it is being
called from multiple places. Cleaned up code in function "ft_recv_write_data"
w.r.t DDP.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When work is scheduled with schedule_work(), the work can end up
running on multiple CPUs at the same time -- this happens if
the work is already running on one CPU and schedule_work() is called
on another CPU. This leads to list corruption with target_qf_do_work(),
which is roughly doing:
spin_lock(...);
list_for_each_entry_safe(...) {
list_del(...);
spin_unlock(...);
// do stuff
spin_lock(...);
}
With multiple CPUs running this code, one CPU can end up deleting the
list entry that the other CPU is about to work on.
Fix this by splicing the list entries onto a local list and then
operating on that in the work function. This way, each invocation of
target_qf_do_work() operates on its own local list and so multiple
invocations don't corrupt each other's list. This also avoids dropping
and reacquiring the lock for each list entry.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
commit 22a85e4cd5 (spi/imx: add device tree probe support) broke spi-imx usage
when the SPI chipselect is the one internal to the controller.
On a mx31pdk board the following error is seen:
Registering mxc_nand as whole device
------------[ cut here ]------------
WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x4c/0xf4()
autorequest GPIO-0
Modules linked in:
[<c0014410>] (unwind_backtrace+0x0/0xf4) from [<c0025754>] (warn_slowpath_common+0x4c/0x64)
[<c0025754>] (warn_slowpath_common+0x4c/0x64) from [<c0025800>] (warn_slowpath_fmt+0x30/0x40)
[<c0025800>] (warn_slowpath_fmt+0x30/0x40) from [<c0198688>] (gpio_ensure_requested+0x4c/0xf4)
[<c0198688>] (gpio_ensure_requested+0x4c/0xf4) from [<c01988c8>] (gpio_direction_output+0xa0/0x138)
[<c01988c8>] (gpio_direction_output+0xa0/0x138) from [<c01ed198>] (spi_imx_setup+0x38/0x4c)
[<c01ed198>] (spi_imx_setup+0x38/0x4c) from [<c01eb5d0>] (spi_setup+0x38/0x50)
[<c01eb5d0>] (spi_setup+0x38/0x50) from [<c01eb85c>] (spi_add_device+0x94/0x124)
[<c01eb85c>] (spi_add_device+0x94/0x124) from [<c01eb960>] (spi_new_device+0x74/0xac)
[<c01eb960>] (spi_new_device+0x74/0xac) from [<c01eb9b8>] (spi_match_master_to_boardinfo+0x20/0x40)
[<c01eb9b8>] (spi_match_master_to_boardinfo+0x20/0x40) from [<c01eba88>] (spi_register_master+0xb0/0x104)
[<c01eba88>] (spi_register_master+0xb0/0x104) from [<c01ec0b4>] (spi_bitbang_start+0x104/0x17c)
[<c01ec0b4>] (spi_bitbang_start+0x104/0x17c) from [<c02c2c4c>] (spi_imx_probe+0x2fc/0x404)
[<c02c2c4c>] (spi_imx_probe+0x2fc/0x404) from [<c01c2498>] (platform_drv_probe+0x18/0x1c)
[<c01c2498>] (platform_drv_probe+0x18/0x1c) from [<c01c1058>] (driver_probe_device+0x78/0x174)
[<c01c1058>] (driver_probe_device+0x78/0x174) from [<c01c11e0>] (__driver_attach+0x8c/0x90)
[<c01c11e0>] (__driver_attach+0x8c/0x90) from [<c01c0860>] (bus_for_each_dev+0x60/0x8c)
[<c01c0860>] (bus_for_each_dev+0x60/0x8c) from [<c01c0088>] (bus_add_driver+0xa0/0x288)
[<c01c0088>] (bus_add_driver+0xa0/0x288) from [<c01c179c>] (driver_register+0x78/0x18c)
[<c01c179c>] (driver_register+0x78/0x18c) from [<c0008490>] (do_one_initcall+0x34/0x178)
[<c0008490>] (do_one_initcall+0x34/0x178) from [<c03a5204>] (kernel_init+0x74/0x118)
[<c03a5204>] (kernel_init+0x74/0x118) from [<c000f65c>] (kernel_thread_exit+0x0/0x8)
---[ end trace 759f924b30fd5a44 ]---
Fix this issue by using the original chip select logic and make spi-imx to work again.
Tested on a mx31pdk that uses the hardware SPI chipselect pins and also
on a mx27pdk that uses GPIO as SPI chipselect.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Support new device OKI SEMICONDUCTOR ML7831 IOH(Input/Output Hub)
ML7831 is for general purpose use.
ML7831 is companion chip for Intel Atom E6xx series.
ML7831 is completely compatible for Intel EG20T PCH.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added the processing which should be done to hardware,
when a FIFO over run error occurred.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed the issue which receives an unnecessary packet before link
When using PHY of GMII, an unnecessary packet is received,
And it becomes impossible to receive a packet after link up.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was originally done as part of commit
65f0b417de ("sfc: Use write-combining to
reduce TX latency"), but that had to be reverted.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commits 65f0b417de,
d88d6b05fe,
fcfa060468,
747df2258b and
867955f568.
Depending on the processor model, write-combining may result in
reordering that the NIC will not tolerate. This typically results
in a DMA error event and reset by the driver, logged as:
sfc 0000:0e:00.0: eth2: TX DMA Q reports TX_EV_PKT_ERR.
sfc 0000:0e:00.0: eth2: resetting (ALL)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable changing advertisement settings via ethtool.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 1G link LED for the BCM578xx-SFI/KR.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change XMAC loopback type from CORE LOCAL to LINE LOCAL for the BCM578xx due to intermittent problem with the loopback with this configuration.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove remote fault detection as a tactic retreat due to link issues involved with it.
Once issue is resolved, this feature will be restored again.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable FEC(Forward Error Correction) for 57810-KR to reduce link errors.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETS bandwidth of 0% is not allowed by driver, so provide alternative HW configuration for this case.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add USB product ID for iPhone 4 CDMA Verizon
Tested on at least 2 devices
Signed-off-by: Kavan Smith <kavansmith82@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seperated Rx and Tx coalescing to different state machines.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of VNs for 4-port devices is 2 instead of 4
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the size in bp, read from bp when queried.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may happen every link toggle.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the thresholds according to 5778x HW and increase rx_ring size
to suit new thresholds in dropless_fc mode.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we allocate/change the IRQ informations, we do not
need to use spinlocks. We can use a mutex (which is
what the generic IRQ code does for allocations/changes).
Fixes a slew of:
BUG: sleeping function called from invalid context at /linux/kernel/mutex.c:271
in_atomic(): 1, irqs_disabled(): 0, pid: 3216, name: xenstored
2 locks held by xenstored/3216:
#0: (&u->bind_mutex){......}, at: [<ffffffffa02e0920>] evtchn_ioctl+0x30/0x3a0 [xen_evtchn]
#1: (irq_mapping_update_lock){......}, at: [<ffffffff8138b274>] bind_evtchn_to_irq+0x24/0x90
Pid: 3216, comm: xenstored Not tainted 3.1.0-rc6-00021-g437a3d1 #2
Call Trace:
[<ffffffff81088d10>] __might_sleep+0x100/0x130
[<ffffffff81645c2f>] mutex_lock_nested+0x2f/0x50
[<ffffffff81627529>] __irq_alloc_descs+0x49/0x200
[<ffffffffa02e0920>] ? evtchn_ioctl+0x30/0x3a0 [xen_evtchn]
[<ffffffff8138b214>] xen_allocate_irq_dynamic+0x34/0x70
[<ffffffff8138b2ad>] bind_evtchn_to_irq+0x5d/0x90
[<ffffffffa02e03c0>] ? evtchn_bind_to_user+0x60/0x60 [xen_evtchn]
[<ffffffff8138c282>] bind_evtchn_to_irqhandler+0x32/0x80
[<ffffffffa02e03a9>] evtchn_bind_to_user+0x49/0x60 [xen_evtchn]
[<ffffffffa02e0a34>] evtchn_ioctl+0x144/0x3a0 [xen_evtchn]
[<ffffffff811b4070>] ? vfsmount_lock_local_unlock+0x50/0x80
[<ffffffff811a6a1a>] do_vfs_ioctl+0x9a/0x5e0
[<ffffffff811b476f>] ? mntput+0x1f/0x30
[<ffffffff81196259>] ? fput+0x199/0x240
[<ffffffff811a7001>] sys_ioctl+0xa1/0xb0
[<ffffffff8164ea82>] system_call_fastpath+0x16/0x1b
Reported-by: Jim Burns <jim_burn@bellsouth.net>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Building a kernel with hotplug disabled results in a link failure:
`bgpio_remove' referenced in section `___ksymtab_gpl+bgpio_remove' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
This is because of bgpio_remove() is exported. It is illegal to export
symbols which are discarded either at link time or as part of an
init/exit section.
Fix this by dropping the __devexit attributation from bgpio_remove().
Also drop the __devinit attributation from bgpio_init().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
per_cpu(processors, n) can be NULL, resulting in:
Loading CPUFreq modules[ 437.661360] BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffffa0434314>] pcc_cpufreq_cpu_init+0x74/0x220 [pcc_cpufreq]
It's better to avoid the oops by failing the driver, and allowing the
system to boot.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Len Brown <lenb@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver does not generate an alarm interrupt even though a time for
an alarm is set.
This results from disabling rtc_clk after setting the alarm time.
To generate an alarm interrupt the driver should maintain its enabled
state for rtc_clk the until alarm interrupt occurs. This patch permits
generation of an alarm interrupt.
[akpm@linux-foundation.org: make s3c_rtc_alarm_clk_lock local to s3c_rtc_alarm_clk_enable()]
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix regression introduced by commit 5ada28bf76 ("led-class: always
implement blinking") which broke sysfs delay handling by not storing the
updated value. Consequently it was only possible to set one of the delays
through the sysfs interface as the other delay was automatically restored
to it's default value. Reading the parameters always gave the defaults.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Cc: <stable@kernel.org> [2.6.37+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In drivers/misc/pti.c::pti_control_frame_built_and_sent() we assign 'comm'
to 'thread_name_p' if (!thread_name). The problem is that 'comm' then
goes out of scope and later we use 'thread_name_p' which now refers to an
out-of-scope variable. To fix that, simply move 'comm' up to have
function scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Cc: Jeremy Rocher <rocher.jeremy@gmail.com>
Cc: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix these errors:
drivers/tty/serial/crisv10.c:4453: error: 'if_ser0' undeclared (first use in this function): 2 errors in 2 logs
drivers/tty/serial/crisv10.c:4453: error: (Each undeclared identifier is reported only once: 2 errors in 2 logs
drivers/tty/serial/crisv10.c:4453: error: for each function it appears in.): 2 errors in 2 logs
"if_ser0" is a typo, it should be "if_serial_0".
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include linux/sched.h to fix below build error.
CC drivers/rtc/rtc-imxdi.o
drivers/rtc/rtc-imxdi.c: In function 'di_write_wait':
drivers/rtc/rtc-imxdi.c:168: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
drivers/rtc/rtc-imxdi.c:168: error: (Each undeclared identifier is reported only once
drivers/rtc/rtc-imxdi.c:168: error: for each function it appears in.)
drivers/rtc/rtc-imxdi.c:168: error: implicit declaration of function 'signal_pending'
drivers/rtc/rtc-imxdi.c:168: error: implicit declaration of function 'schedule_timeout'
drivers/rtc/rtc-imxdi.c: In function 'dryice_norm_irq':
drivers/rtc/rtc-imxdi.c:329: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://bedivere.hansenpartnership.com/git/scsi-rc-fixes-2.6: (25 commits)
[SCSI] bnx2i: Fixed the endian on TTT for NOP out transmission
[SCSI] libfc: fix referencing to fc_fcp_pkt from the frame pointer via fr_fsp()
[SCSI] libfc: block SCSI eh thread for blocked rports
[SCSI] libfc: fix fc_eh_host_reset
[SCSI] fcoe: Fix deadlock between fip's recv_work and rtnl
[SCSI] qla2xxx: Update version number to 8.03.07.07-k.
[SCSI] qla2xxx: Set the task attributes after memsetting fcp cmnd.
[SCSI] qla2xxx: Correct inadvertent loop state transitions during port-update handling.
[SCSI] qla2xxx: Save and restore irq in the response queue interrupt handler.
[SCSI] qla2xxx: Double check for command completion if abort mailbox command fails.
[SCSI] qla2xxx: Acquire hardware lock while manipulating dsd list.
[SCSI] qla2xxx: Fix qla24xx revision check while enabling interrupts.
[SCSI] qla2xxx: T10 DIF - Fix incorrect error reporting.
[SCSI] qla2xxx: T10 DIF - Handle uninitalized sectors.
[SCSI] hpsa: fix physical device lun and target numbering problem
[SCSI] hpsa: fix problem that OBDR devices are not detected
[SCSI] isci: add version number
[SCSI] isci: fix event-get pointer increment
[SCSI] isci: dynamic interrupt coalescing
[SCSI] isci: Leave requests alone if already terminating.
...
Apparently this doesn't always work reliably, e.g. at resume time.
Just initialize to 0, so the ring is considered empty.
Tested with hibernation on Sumo and Cayman cards.
Should fix https://bugs.launchpad.net/ubuntu/+source/linux/+bug/820746/ .
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes an information leak to userspace, we were handing out un-zeroed pages
for any newly created TTM_PL_TT buffer.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
ttarget is initialized when the driver is loaded, but tmin is not.
As a result, tempX_max_hyst attributes read 0. Fix this.
Also use THERM_*_THRESHOLD* constants in these initializations instead
of hard-coding the constants.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In pcie_find_smpss(), we have the following statement:
if (dev->is_hotplug_bridge && (!list_is_singular(&dev->bus->devices) ||
dev->bus->self->pcie_type != PCI_EXP_TYPE_ROOT_PORT))
The problem is that at least on my machine, this gets called for the
root complex (virtual P2P bridge), and dev->bus->self is NULL since
the parent bus for this is not itself anchor to a PCI device.
This adds the necessary NULL check.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jon Mason <mason@myri.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark this lowlevel IRQ handler as non-threaded. This prevents a boot
crash when "threadirqs" is on the kernel commandline. Also the
interrupt handler is handling hardware critical events which should
not be delayed into a thread.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the command queue is constantly busy,
which can happen in P2P, the hangcheck
timer will frequently find a command in
it and will eventually reset the device
because nothing sets the timestamp for
this queue when commands are processed.
Fix this by setting the timestamp when
a command completes.
Cc: stable@kernel.org #2.6.39, #3.0.0 #3.1.0
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SIgned-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexander reported a strange crash in iwlagn that
Meenakshi and Wey couldn't reproduce. I just ran
into the same issue and tracked it down to stack
corruption. This fixes it.
The problem was introduced in
commit 4b8b99b6e650d0527f3a123744b7459976581d14
Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Date: Fri Jul 8 14:29:48 2011 -0700
iwlagn: radio sensor offset in le16 format
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reported-by: Alexander Diewald <alex@diewald.cc>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver fails to clear encryption keys making it impossible
to switch connections.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.39+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver fails to connect to 802.11n-enabled APs. The patch fixes
Bug #42262.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.39+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Temperature alarms are detected by checking the alarm bit and comparing
temperature limits against the current temperature. For low limits, this
comparison needs to be reversed (temp < limit instead of temp > limit).
This was not taken into account, resulting in wrong alarms if a temperature
fell below a low limit.
Fix by adding a low limit flag in the limit data structure. When creating the
sensor entry, the order of registers to compare is now reversed for low limits.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 3.0+
Bamboos with Product ID's > 0xD4 return values unrelated to pressure
in touch 1 pressure field. They also report 2nd touch X/Y values
shifted down 1 byte (where pressure was). This results in jumpy
1 finger touch and totally invalid 2nd finger data.
For touch detection, switch to a Touch Present single bit that
all versions of Bamboo support.
For touch 2 offset, calculate offset based on a bit that is set
different between the two packet layouts.
Since touch pressure reports were removed from driver, there was
no need to be reading pressure any more.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Reviewed-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Remove duplicate "return" statement
drm/nv04/crtc: Bail out if FB is not bound to crtc
drm/nouveau: fix nv04_sgdma_bind on non-"4kB pages" archs
drm/nouveau: properly handle allocation failure in nouveau_sgdma_populate
drm/nouveau: fix oops on pre-semaphore hardware
drm/nv50/crtc: Bail out if FB is not bound to crtc
drm/radeon/kms: fix DP detect and EDID fetch for DP bridges
dvb_usb_device_init calls the frontend_attach method of this driver which
uses vp7045_usb_ob. In order to have a buffer ready in vp7045_usb_op, it has to
be allocated before that happens.
Luckily we can use the whole private data as the buffer as it gets separately
allocated on the heap via kzalloc in dvb_usb_device_init and is thus apt for
use via usb_control_msg.
This fixes a
BUG: unable to handle kernel paging request at 0000000000001e78
reported by Tino Keitel and diagnosed by Dan Carpenter.
Cc: stable@kernel.org # For v3.0 and upper
Tested-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The nuvoton-cir driver was storing up consecutive pulse-pulse and
space-space samples internally, for no good reason, since
ir_raw_event_store_with_filter() already merges back to back like
samples types for us. This should also fix a regression introduced late
in 3.0 that related to a timeout change, which actually becomes correct
when coupled with this change. Tested with RC6 and RC5 on my own
nuvoton-cir hardware atop vanilla 3.0.0, after verifying quirky
behavior in 3.0 due to the timeout change.
Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Stephan Raue <sraue@openelec.tv>
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the unlikely case that pci_find_bus() should return NULL
viacam_serial_is_enabled() is going to dereference a NULL pointer and
blow up. Better safe than sorry, so be defensive and check the
pointer.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The images are clearer with a lower bridge clock.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bug was introduced by git commit 0e4d413af1, giving very dark images.
Signed-off-by: Luiz Carlos Ramos <lramos.prof@yahoo.com.br>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The list of the webcams which have LED inversion was rebuild scanning
ms-win .inf files.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
'!' has higher precedence than '&' so we need parenthesis here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When CONFIG_NET is disabled, SCSI_QLA_ISCSI selects SCSI_ISCSI_ATTRS,
which uses network interfaces, so the build fails with multiple errors:
warning: (ISCSI_TCP && SCSI_CXGB3_ISCSI && SCSI_CXGB4_ISCSI && SCSI_QLA_ISCSI && INFINIBAND_ISER) selects SCSI_ISCSI_ATTRS which has unmet direct dependencies (SCSI && NET)
ERROR: "skb_trim" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "netlink_kernel_create" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
ERROR: "netlink_kernel_release" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
...
so make SCSI_QLA_ISCSI also depend on NET to prevent the build errors.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: iscsi-driver@qlogic.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7088/1: entry: fix wrong parameter name used in do_thumb_abort
ARM: 7080/1: l2x0: make sure I&D are not locked down on init
ARM: 7081/1: mach-integrator: fix the clocksource
NET: am79c961: fix race in link status code
ARM: 7067/1: mm: keep significant bits in pfn_valid
Since backlight_types[] isn't modified, let's declare it const. That
was probably the intention of the author of commit bb7ca747f8
("backlight: add backlight type"), via which the "const char const *"
construct was introduced. The duplicate const was detected by sparse.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://neil.brown.name/md:
md: Fix handling for devices from 2TB to 4TB in 0.90 metadata.
md/raid1,10: Remove use-after-free bug in make_request.
md/raid10: unify handling of write completion.
Avoid dereferencing a 'request_queue' after last close.
0.90 metadata uses an unsigned 32bit number to count the number of
kilobytes used from each device.
This should allow up to 4TB per device.
However we multiply this by 2 (to get sectors) before casting to a
larger type, so sizes above 2TB get truncated.
Also we allow rdev->sectors to be larger than 4TB, so it is possible
for the array to be resized larger than the metadata can handle.
So make sure rdev->sectors never exceeds 4TB when 0.90 metadata is in
used.
Also the sanity check at the end of super_90_load should include level
1 as it used ->size too. (RAID0 and Linear don't use ->size at all).
Reported-by: Pim Zandbergen <P.Zandbergen@macroscoop.nl>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
A single request to RAID1 or RAID10 might result in multiple
requests if there are known bad blocks that need to be avoided.
To detect if we need to submit another write request we test:
if (sectors_handled < (bio->bi_size >> 9)) {
However this is after we call **_write_done() so the 'bio' no longer
belongs to us - the writes could have completed and the bio freed.
So move the **_write_done call until after the test against
bio->bi_size.
This addresses https://bugzilla.kernel.org/show_bug.cgi?id=41862
Reported-by: Bruno Wolff III <bruno@wolff.to>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: NeilBrown <neilb@suse.de>
A write can complete at two different places:
1/ when the last member-device write completes, through
raid10_end_write_request
2/ in make_request() when we remove the initial bias from ->remaining.
These two should do exactly the same thing and the comment says they
do, but they don't.
So factor the correct code out into a function and call it in both
places. This makes the code much more similar to RAID1.
The difference is only significant if there is an error, and they
usually take a while, so it is unlikely that there will be an error
already when make_request is completing, so this is unlikely to cause
real problems.
Signed-off-by: NeilBrown <neilb@suse.de>
Modifying the Maximum Read Request Size to 0 (value of 128Bytes) has
massive negative ramifications on some devices. Without knowing which
devices have this issue, do not modify from the default value when
walking the PCI-E bus in pcie_bus_safe mode. Also, make pcie_bus_safe
the default procedure.
Tested-by: Sven Schnelle <svens@stackframe.org>
Tested-by: Simon Kirby <sim@hostway.ca>
Tested-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-and-tested-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
References: https://bugzilla.kernel.org/show_bug.cgi?id=42162
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b03e7495a8 ("PCI: Set PCI-E Max Payload Size on fabric")
introduced a potential NULL pointer dereference in calls to
pcie_bus_configure_settings due to attempts to access pci_bus self
variables when the self pointer is NULL.
To correct this, verify that the self pointer in pci_bus is non-NULL
before dereferencing it.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://dev.laptop.org/users/cjb/mmc:
mmc: sdhci-s3c: Fix mmc card I/O problem
mmc: sd: UHS-I bus speed should be set last in UHS initialization
mmc: sdhi: initialise mmc_data->flags before use
mmc: core: use non-reentrant workqueue for clock gating
mmc: core: prevent aggressive clock gating racing with ios updates
mmc: rename mmc_host_clk_{ungate|gate} to mmc_host_clk_{hold|release}
mmc: sdhci-esdhc-imx: add missing inclusion of linux/module.h
This patch adds trackpad support for the MacBookAir4,1, released in July 2011.
It is very similar to the MacBookAir4,2 patch submitted by Joshua Dillon and
Chase Douglas.
Signed-off-by: Pieter-Augustijn Van Malleghem <p-a@scarlet.be>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove the duplicate "return" statement in drm_fb_helper_panic().
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nv04/crtc: Bail out if FB is not bound to crtc
drm/nouveau: fix nv04_sgdma_bind on non-"4kB pages" archs
drm/nouveau: properly handle allocation failure in nouveau_sgdma_populate
drm/nouveau: fix oops on pre-semaphore hardware
drm/nv50/crtc: Bail out if FB is not bound to crtc
This commit resolves a possible 'NULL pointer dereference'
It uses the same approach as radeon, intel and nouveau/nv50
Fixes bug 'Nouveau: Kernel oops when unplugging external monitor'
https://bugs.freedesktop.org/show_bug.cgi?id=40336
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nv04_sgdma_bind binds the same page multiple times on
architectures where PAGE_SIZE != 4096.
Let's fix it.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not cleaning after alloc failure would result in crash on destroy,
because nouveau_sgdma_clear assumes "ttm_alloced" to be not null when
"pages" is not null.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine/ste_dma40: fix memory leak due to prepared descriptors
dmaengine/ste_dma40: fix Oops due to double free of client descriptor
dmaengine/ste_dma40: remove duplicate call to d40_pool_lli_free().
dmaengine/ste_dma40: add missing kernel doc for pending_queue
* 'for-linus' of git://twin.jikos.cz/jikos/hid:
HID: wacom: Unregister sysfs attributes on remove
HID: wacom: Fix error path of power-supply initialization
HID: add support for HuiJia USB Gamepad connector
HID: magicmouse: ignore 'ivalid report id' while switching modes, v2
HID: magicmouse: Set resolution of touch surfaces
* 'amd/fixes' of git://git.8bytes.org/scm/iommu:
iommu/amd: Don't take domain->lock recursivly
iommu/amd: Make sure iommu->need_sync contains correct value
Adds INPUT_PROP_POINTER or INPUT_PROP_DIRECT as necessary to the
hardware supported by the Wacom driver. The DIRECT property is
assigned to devices with an embedded screen (i.e. touchscreens
and display tablets). The POINTER property is assigned to those
without embedded screens.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'timers-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
rtc: twl: Fix registration vs. init order
rtc: Initialized rtc_time->tm_isdst
rtc: Fix RTC PIE frequency limit
rtc: rtc-twl: Remove lockdep related local_irq_enable()
rtc: rtc-twl: Switch to using threaded irq
rtc: ep93xx: Fix 'rtc' may be used uninitialized warning
alarmtimers: Avoid possible denial of service with high freq periodic timers
alarmtimers: Memset itimerspec passed into alarm_timer_get
alarmtimers: Avoid possible null pointer traversal
* branch 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: not build debug messages with CONFIG_UBIFS_FS_DEBUG disabled
* branch 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: do not link debug messages when debugging is disabled
HID devices can be hotplugged so we should unregister all sysfs attributes when
removing a driver. Otherwise, manually unloading the wacom-driver will not
remove the sysfs attributes. Only when the device is disconnected, they are
removed, eventually.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
power_supply_unregister() must not be called if power_supply_register() failed.
The wdata->psy.dev pointer may point to invalid memory after a failed
power_supply_register() and hence wacom_remove() will fail while calling
power_supply_unregister().
This changes the wacom_probe function to fail if it cannot register the
power_supply devices. If we would want to keep the previous behaviour we had to
keep some flag about the power_supply state and check it on wacom_remove, but
this seems inappropriate here. Hence, we simply fail, too, if
power_supply_register fails.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In tegra_i2c_fill_tx_fifo, once we have finished pushing all the bytes
to the I2C hardware controller, the interrupt might happen before we
have updated i2c_dev->msg_buf_remaining at the end of the function.
Then, in tegra_i2c_isr, we will call again tegra_i2c_fill_tx_fifo
triggering weird behaviour. This has been shown to happen under real
conditions.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch was intended to be part of 7ca2d1a105a239e300b937e9c41a10a4bd08f569
"i2c: Tegra: Add DeviceTree support". However, an early version of that patch,
which was missing a chunk, was applied to next-i2c. This change is that
missing chunk.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rewrite the loop walking the id array during probe. The new code is
better adapted to a null-terminated array, and is also clearer and
more efficient than the original.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Current calculation is completely wrong. Add missing brackets to fix it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 3.0+
The patch fixes the build failure:
drivers/mfd/omap-usb-host.c:1034:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1034:1: warning: type defaults to 'int' in
declaration of 'EXPORT_SYMBOL_GPL'
drivers/mfd/omap-usb-host.c:1034:1: warning: parameter names (without
types) in function declaration
drivers/mfd/omap-usb-host.c:1040:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1040:1: warning: type defaults to 'int' in
declaration of 'EXPORT_SYMBOL_GPL'
drivers/mfd/omap-usb-host.c:1040:1: warning: parameter names (without
types) in function declaration
drivers/mfd/omap-usb-host.c:1045:13: error: 'THIS_MODULE' undeclared
here (not in a function)
drivers/mfd/omap-usb-host.c:1050:15: error: expected declaration
specifiers or '...' before string constant
drivers/mfd/omap-usb-host.c:1050:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1050:1: warning: type defaults to 'int' in
declaration of 'MODULE_AUTHOR'
drivers/mfd/omap-usb-host.c:1050:15: warning: function declaration isn't
a prototype
drivers/mfd/omap-usb-host.c:1051:14: error: expected declaration
specifiers or '...' before string constant
drivers/mfd/omap-usb-host.c:1051:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1051:1: warning: type defaults to 'int' in
declaration of 'MODULE_ALIAS'
drivers/mfd/omap-usb-host.c:1051:14: warning: function declaration isn't
a prototype
drivers/mfd/omap-usb-host.c:1052:16: error: expected declaration
specifiers or '...' before string constant
drivers/mfd/omap-usb-host.c:1052:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1052:1: warning: type defaults to 'int' in
declaration of 'MODULE_LICENSE'
drivers/mfd/omap-usb-host.c:1052:16: warning: function declaration isn't
a prototype
drivers/mfd/omap-usb-host.c:1053:20: error: expected declaration
specifiers or '...' before string constant
drivers/mfd/omap-usb-host.c:1053:1: warning: data definition has no type
or storage class
drivers/mfd/omap-usb-host.c:1053:1: warning: type defaults to 'int' in
declaration of 'MODULE_DESCRIPTION'
drivers/mfd/omap-usb-host.c:1053:20: warning: function declaration isn't
a prototype
make[2]: *** [drivers/mfd/omap-usb-host.o] Error 1
CC fs/proc/namespaces.o
make[1]: *** [drivers/mfd] Error 2
make: *** [drivers] Error 2
make: *** Waiting for unfinished jobs....
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This code section seems to have been accidentally copy pasted.
It causes incorrect bits to be set up in the TLL_CHANNEL_CONF
register and prevents the TLL mode from working correctly.
Cc: stable@kernel.org
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Required platform information is not handed to max8997-irq.c properly.
This patch enables to hand over such information to max8997-irq.c so
that max8997-irq functions properly.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix regression introduced by commit
a2974732ca (TPS65911: Add new irq
definitions) which caused irq_num to be incorrectly set for tps65910.
Cc: stable@kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the twl4030-madc device wasn't registered, and another device, such
as twl4030-madc-hwmon, calls twl4030_madc_conversion() a NULL pointer is
dereferenced.
Signed-off-by: Kyle Manna <kyle@kylemanna.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Worst case this fixes the following error:
[ 72.086212] (NULL device *): conversion timeout!
Best case it prevents a crash
Signed-off-by: Kyle Manna <kyle@kylemanna.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The kernel already has a function with this name declared
in asm-generic/gpio.h. So if this header leaks into wm8350/gpio.c
we get
drivers/mfd/wm8350-gpio.c:40:12: error: conflicting types for 'gpio_set_debounce'
include/asm-generic/gpio.h:156:12: note: previous declaration of 'gpio_set_debounce' was here
Fix this by adding a wm8350_ prefix to the function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Sink type is always DP for DP bridges and EDID fetch on
DP bridges is always i2c over aux rather than plain i2c.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The conversion to per bus type registration functions means we don't need
to do module_get()s to hold the bus types in memory (their users will link
to them) so we removed all those calls. This left module_put() calls in
the cleanup paths which aren't needed and which cause unbalanced puts if
we ever try to unload anything.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Prepared descriptors that are not submitted will not be freed. Add
prepared descriptor to a list to be able to release them upon
dmaengine_terminate_all().
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The client list may exist in two lists at the same time. This makes free
fail since the same desc is freed multiple times. Remove desc from
client list when adding it to the pending queue. Move free of client owned
descriptors from free_dma() to terminate_all().
Unable to handle kernel paging request at virtual address 00100104
pgd = dea8c000
[00100104] *pgd=1ea62831, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 Not tainted (3.1.0-rc3+ #58)
PC is at d40_free_chan_resources+0x64/0x330
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The link status code operates from a timer, and writes the index
register without first taking a lock. A well-placed interrupt
between writing the index register and reading the data register
could change the index register on us, which will return wrong data.
Add the necessary lock.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andi Kleen