Distinguish usart and uart by read ip name register,
The usart read name is "USAR",
The uart and dbgu read name is "DBGU".
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will switch to pio mode when request of dma or pdc fail.
But soon or later, when the request is success, the transfer mode can switch to them at
next open serial port action.
So in startup stage, we should get original transfer mode.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request a cyclic dma channel for rx dma use. Use cyclic transfer is to prevent
receive data overrun.
We allocate a cycle dma cookie after request channel,
after that, enable uart timeout interrupt in startup stage, when data successful
received, the timeout callback will check the residual bytes and insert
receiving datas into the framework during the transfer interval.
When current descriptor finished, the dma callback will also check the residual
bytes and filp the receiving data.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request a slave dma channel for tx dma use. Tx dma will setup a single transfer,
when transfer complete, it will call atmel_complete_tx_dma to do finish stuff.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use function pointer can avoid define atmel_use_pdc_tx/rx everywhere.
(*prepare_rx/tx)() is in setup transfer stage.
(*schedule_rx/tx)() is in tasklet schedule stage.
(*release_rx/tx)() is used when shutdown the transfer.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA is available since at91sam9x5 socs, before that, we use PDC.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dmi_table is best accessed from the probe function, which is not
an __init function. Drop the __initdata annotation from the dmi_table
to avoid the section mismatch compiler warnings:
WARNING: drivers/tty/serial/pch_uart.o(.text+0x4871): Section mismatch
in reference from the function pch_uart_init_port() to the variable
.init.data:pch_uart_dmi_table
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes wrong dev_pm_ops which caused by commit:
serial: max310x: Driver rework.
CC drivers/tty/serial/max310x.o
LD drivers/video/fb.o
CC drivers/w1/slaves/w1_ds2433.o
CC drivers/w1/slaves/w1_ds2760.o
CC drivers/xen/balloon.o
CC drivers/video/backlight/adp8870_bl.o
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.suspend') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.resume') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.freeze') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.thaw') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.poweroff') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.restore') [enabled by default]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace kzalloc and clk_get by their managed counterparts to simplify
error and cleanup paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UARTDM cores have a TX fifo that can accept more than one
character per register write, but the msm_serial driver currently
only supports 1 character mode. Add support for this mode of operation
to speed up the transmit path on DM devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently msm_set_baud_rate() assumes the uart clock rate is
1.8432 MHz. This is not always true, and limits our options to
program the baud rate. Instead of assuming the rate and
hard-coding the baud_code based on it, calculate the divider that
we want and try to find the closest baud_code that matches. This
allows us to support uarts with faster clock speeds.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/msm_serial.c:302:6: warning: symbol 'msm_set_mctrl' was
not declared. Should it be static?
drivers/tty/serial/msm_serial.c:597:17: warning: incorrect type in argument 2
(different address spaces)
drivers/tty/serial/msm_serial.c:597:17: expected void volatile [noderef] <asn:2>*addr
drivers/tty/serial/msm_serial.c:597:17: got unsigned int *
drivers/tty/serial/msm_serial.c:608:33: warning: incorrect type in argument 1
(different address spaces)
drivers/tty/serial/msm_serial.c:608:33: expected void volatile [noderef] <asn:2>*addr
drivers/tty/serial/msm_serial.c:608:33: got unsigned int *gsbi_base
drivers/tty/serial/msm_serial.c:648:37: warning: incorrect type in assignment
(different address spaces)
drivers/tty/serial/msm_serial.c:648:37: expected unsigned int *gsbi_base
drivers/tty/serial/msm_serial.c:648:37: got void [noderef] <asn:2>*
Mark the ioremapped memory as __iomem and use writel instead of
iowrite because we're not dealing with PCI devices. Also, mark
msm_set_mctrl() static because it isn't used outside this file.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UARTDM serial devices require us to wait for the entire TX fifo
to drain before we can change the contents of the NCF_TX
register. Furthermore, if we write any characters to the TX fifo
within the same clock cycle of changing the NCF_TX register the
NCF_TX register won't latch properly.
To fix these issues we should read back the NCF_TX register to
delay any TX fifo accesses by a clock cycle and we should wait
for the TX fifo to drain (instead of just waiting for the fifo to
be ready to receive more characters). Failure to do so leads to
random NUL bytes interspersed in the output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quirks and PCI ID table entries for the original ADDI-DATA APCI-7800
(not the newer APCI-7800-3) use PCI_DEVICE_ID_ADDIDATA_APCI7800 from
<linux/pci_ids.h> but the device ID was actually assigned to ADDI-DATA
by Applied Micro Circuits Corporation (PCI_VENDOR_ID_AMCC). Replace it
locally with #define PCI_DEVICE_ID_AMCC_ADDIDATA_APCI7800.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI_VENDOR_ID_ADDIDATA_OLD has the same value (0x10e8) as
PCI_VENDOR_ID_AMCC in <linux/pci_ids.h>. The vender ID is actually
assigned to Applied Micro Circuits Corporation. The 8250_pci driver
uses PCI_VENDOR_ID_ADDIDATA_OLD in the lists of quirks and PCI IDs for
the ADDI-DATA APCI-7800 card. Change it to use the more accurate
PCI_VENDOR_ID_AMCC.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP is common
across all the ST parts for settop box platforms.
ASC is embedded in ST COMMS IP block. It supports Rx & Tx functionality.
It support all industry standard baud rates.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver fails to build on x86 because writel_relaxed isn't available
there. That function exists on arm, arm64, avr32, hexagon, mips and sh,
but adding all these is overkill so stick to arm only.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing iounmap() before return from msm_request_port()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No idea why we have redundant testing for ifdef CONFIG_SERIAL_BFIN_MODULE,
check it once is enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the DMI interface rather than manually matching DMI strings.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Cc: Michael Brunner <mibru@gmx.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some serial ports will not use the standard base baud rate. Report
this after initialization so it might be discovered and used for early
console configuration.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If earlyprintk is enabled and current UART is console port the platform
code can mark it as RPM_ACTIVE to sync real IP state with PM Runtime and
avoid resuming of already active device, but now, driver initialization
will be performed in the wrong way:
pm_runtime_enable(&pdev->dev);
<-- PM runtime alowed (device state RPM_ACTIVE)
if (omap_up_info->autosuspend_timeout == 0)
omap_up_info->autosuspend_timeout = -1;
device_init_wakeup(up->dev, true);
pm_runtime_use_autosuspend(&pdev->dev);
<-- update_autosuspend() will be called and it will disable device
(device state RPM_SUSPENDED)
pm_runtime_set_autosuspend_delay(&pdev->dev,
omap_up_info->autosuspend_timeout);
<-- update_autosuspend() will be called which will re-enable device
(device state RPM_ACTIVE), because autosuspend_timeout < 0
pm_runtime_irq_safe(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
<-- will do nothing
Such behavior isn't expected by OMAP serial drivers and causes
unpredictable calls of serial_omap_runtime_suspend() and
serial_omap_runtime_resume().
Hence, fix it by allowing PM runtime only after all its parameters are
configured.
CC: Tony Lindgren <tony@atomide.com>
CC: Rajendra Nayak <rnayak@ti.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function lpuart_setup_watermark() clears some bits in register UARTCR2
before writing FIFO configuration registers as required by hardware.
But it should restore UARTCR2 after that. Otherwise, we end up changing
UARTCR2 register when setting up watermark, and that is not really
desirable. At least, when low-level debug and earlyprint is enabled,
serial console is broken due to it.
Fix the problem by restoring UARTCR2 register at the end of function
lpuart_setup_watermark().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise serial driver would crash accessing platform_data that was
not initialized in functions like:
serial_omap_pm(...)
...
if (!state && pdata->enable_wakeup)
^^^^^^^
...
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The revision register is a 32 bit register. The serial_in() function reads
only the lower 16 bits of the register. This leads to an incorrect computation
of the Module revision.
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
[oleksandr.savchenko@ti.com: add some whitespaces]
Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current logic results in interrupt storm since the fifo
is constantly below the threshold level. Change the logic
to fill all the available spaces in the fifo as long as
we have data to minimize the possibilty of underflow and
elimiate excessive interrupts.
Signed-off-by: Dmitry Fink <finik@ti.com>
Signed-off-by: Alexander Savchenko <oleksandr.savchenko@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wer has TX wakeup bit available enable the same
by populating the necessary tx wakeup flag for the
applicable module ip blocks and use the same
while configuaring wer reg.
Also wer is not context restored, restore wer when
context is lost.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <kevin.hilman@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(for drivers/tty changes)
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent regression about NetMos 9835 Multi-I/O boards indicates
that comment pointing to the parport_serial driver could be helpful.
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for MAX14830 (advanced quad universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for MAX3109 (advanced dual universal asynchronous
receiver-transmitter) into max310x driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch rework max310x driver.
Major changes have been made:
- Prepare driver to support ICs with more than one UART.
- Prepare driver to support work with I2C-bus.
The patch changes almost every function and can not be divided into parts.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only enable the DMA support when the following are meet:
[1] The uart port supports the hardware flow control(CTS/RTS).
(Some uart port does not support the CTS/RTS.)
[2] The application enables the CTS/RTS.
[3] The Soc is imx6q.
For the sdma's firmware limit, we do not support the DMA except
the imx6q platform.
[4] The uart is not used as a console.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was not possible to set custom-baudrates like 62500.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will add the DMA support for the imx uart. For the firmware's limit,
only the imx6 serial chips (including the imx6q, imx6dl, imx6sl) can
support the DMA.
This patch adds the necessary macro and helper to distinguish the
imx6q uart from the other imx uart. Other chips can use the "fsl,imx6q-uart"
to enable the DMA support.
This patch also replaces the check "is_imx21_uart()" with "!is_imx1_uart()".
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart_console() check makes the clocks(clk_per and clk_ipg) opened
even when we close the console uart.
This patch enable/disable the clocks in imx_console_write(),
so we can keep the clocks closed when the console uart is closed.
Also remove the clock enable/disable oprations in the probe, we do not
need them any more.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Barry Song <baohua.song@csr.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ttyTHS is consistent with the name used in driver.
Signed-off-by: Richard Zhao <rizhao@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlier change to use strlcpy uncovered a bug in the options
argument length calculation causing last character to be truncated.
This makes the actual console to be configured with incorrect
baudrate when specifying the console using console=uart,... syntax.
Bug symptom seen in kernel log output:
Kernel command line: console=uart,mmio,0x90000000,115200
Early serial console at MMIO 0x90000000 (options '11520')
which then results in a invalid baud rate 11520 instead of the
expected 115200 when the console is switched to ttyS0 later
in the boot process.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
- Hotplug changes allowing device hot-removal operations to fail
gracefully (instead of crashing the kernel) if they cannot be
carried out completely. From Rafael J Wysocki and Toshi Kani.
- Freezer update from Colin Cross and Mandeep Singh Baines targeted
at making the freezing of tasks a bit less heavy weight operation.
- cpufreq resume fix from Srivatsa S Bhat for a regression introduced
during the 3.10 cycle causing some cpufreq sysfs attributes to
return wrong values to user space after resume.
- New freqdomain_cpus sysfs attribute for the acpi-cpufreq driver to
provide information previously available via related_cpus from
Lan Tianyu.
- cpufreq fixes and cleanups from Viresh Kumar, Jacob Shin,
Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia, Arnd Bergmann, and
Tang Yuantian.
- Fix for an ACPICA regression causing suspend/resume issues to
appear on some systems introduced during the 3.4 development cycle
from Lv Zheng.
- ACPICA fixes and cleanups from Bob Moore, Tomasz Nowicki, Lv Zheng,
Chao Guan, and Zhang Rui.
- New cupidle driver for Xilinx Zynq processors from Michal Simek.
- cpuidle fixes and cleanups from Daniel Lezcano.
- Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk.
- ACPI device power management fixes and cleanups from Fengguang Wu
and Rafael J Wysocki.
- ACPI documentation updates from Lv Zheng, Aaron Lu and Hanjun Guo.
- Fix for the IA-64 issue that was the reason for reverting commit
9f29ab1 and updates of the ACPI scan code from Rafael J Wysocki.
- Mechanism for adding CMOS RTC address space handlers from Lan Tianyu
(to allow some EC-related breakage to be fixed on some systems).
- Spec-compliant implementation of acpi_os_get_timer() from
Mika Westerberg.
- Modification of do_acpi_find_child() to execute _STA in order to
to avoid situations in which a pointer to a disabled device object
is returned instead of an enabled one with the same _ADR value.
From Jeff Wu.
- Intel BayTrail PCH (Platform Controller Hub) support for the ACPI
Intel Low-Power Subsystems (LPSS) driver and modificaions of that
driver to work around a couple of known BIOS issues from
Mika Westerberg and Heikki Krogerus.
- EC driver fix from Vasiliy Kulikov to make it use get_user() and
put_user() instead of dereferencing user space pointers blindly.
- Assorted ACPI code cleanups from Bjorn Helgaas, Nicholas Mazzuca and
Toshi Kani.
- Modification of the "runtime idle" helper routine to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows some code bloat
reduction to be done, from Rafael J Wysocki and Alan Stern.
- New trace points for PM QoS from Sahara <keun-o.park@windriver.com>.
- PM QoS documentation update from Lan Tianyu.
- Assorted core PM code cleanups and changes from Bernie Thompson,
Bjorn Helgaas, Julius Werner, and Shuah Khan.
- New devfreq driver for the Exynos5-bus device from Abhilash Kesavan.
- Minor devfreq cleanups, fixes and MAINTAINERS update from
MyungJoo Ham, Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and
Wei Yongjun.
- OMAP Adaptive Voltage Scaling (AVS) SmartReflex voltage control
driver updates from Andrii Tseglytskyi and Nishanth Menon.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=VBBq
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the total number of ACPI commits is slightly greater than
the number of cpufreq commits, but Viresh Kumar (who works on cpufreq)
remains the most active patch submitter.
To me, the most significant change is the addition of offline/online
device operations to the driver core (with the Greg's blessing) and
the related modifications of the ACPI core hotplug code. Next are the
freezer updates from Colin Cross that should make the freezing of
tasks a bit less heavy weight.
We also have a couple of regression fixes, a number of fixes for
issues that have not been identified as regressions, two new drivers
and a bunch of cleanups all over.
Highlights:
- Hotplug changes to support graceful hot-removal failures.
It sometimes is necessary to fail device hot-removal operations
gracefully if they cannot be carried out completely. For example,
if memory from a memory module being hot-removed has been allocated
for the kernel's own use and cannot be moved elsewhere, it's
desirable to fail the hot-removal operation in a graceful way
rather than to crash the kernel, but currenty a success or a kernel
crash are the only possible outcomes of an attempted memory
hot-removal. Needless to say, that is not a very attractive
alternative and it had to be addressed.
However, in order to make it work for memory, I first had to make
it work for CPUs and for this purpose I needed to modify the ACPI
processor driver. It's been split into two parts, a resident one
handling the low-level initialization/cleanup and a modular one
playing the actual driver's role (but it binds to the CPU system
device objects rather than to the ACPI device objects representing
processors). That's been sort of like a live brain surgery on a
patient who's riding a bike.
So this is a little scary, but since we found and fixed a couple of
regressions it caused to happen during the early linux-next testing
(a month ago), nobody has complained.
As a bonus we remove some duplicated ACPI hotplug code, because the
ACPI-based CPU hotplug is now going to use the common ACPI hotplug
code.
- Lighter weight freezing of tasks.
These changes from Colin Cross and Mandeep Singh Baines are
targeted at making the freezing of tasks a bit less heavy weight
operation. They reduce the number of tasks woken up every time
during the freezing, by using the observation that the freezer
simply doesn't need to wake up some of them and wait for them all
to call refrigerator(). The time needed for the freezer to decide
to report a failure is reduced too.
Also reintroduced is the check causing a lockdep warining to
trigger when try_to_freeze() is called with locks held (which is
generally unsafe and shouldn't happen).
- cpufreq updates
First off, a commit from Srivatsa S Bhat fixes a resume regression
introduced during the 3.10 cycle causing some cpufreq sysfs
attributes to return wrong values to user space after resume. The
fix is kind of fresh, but also it's pretty obvious once Srivatsa
has identified the root cause.
Second, we have a new freqdomain_cpus sysfs attribute for the
acpi-cpufreq driver to provide information previously available via
related_cpus. From Lan Tianyu.
Finally, we fix a number of issues, mostly related to the
CPUFREQ_POSTCHANGE notifier and cpufreq Kconfig options and clean
up some code. The majority of changes from Viresh Kumar with bits
from Jacob Shin, Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia,
Arnd Bergmann, and Tang Yuantian.
- ACPICA update
A usual bunch of updates from the ACPICA upstream.
During the 3.4 cycle we introduced support for ACPI 5 extended
sleep registers, but they are only supposed to be used if the
HW-reduced mode bit is set in the FADT flags and the code attempted
to use them without checking that bit. That caused suspend/resume
regressions to happen on some systems. Fix from Lv Zheng causes
those registers to be used only if the HW-reduced mode bit is set.
Apart from this some other ACPICA bugs are fixed and code cleanups
are made by Bob Moore, Tomasz Nowicki, Lv Zheng, Chao Guan, and
Zhang Rui.
- cpuidle updates
New driver for Xilinx Zynq processors is added by Michal Simek.
Multidriver support simplification, addition of some missing
kerneldoc comments and Kconfig-related fixes come from Daniel
Lezcano.
- ACPI power management updates
Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk, sparse warning fix from Fengguang Wu and
cleanups and fixes of the ACPI device power state selection
routine.
- ACPI documentation updates
Some previously missing pieces of ACPI documentation are added by
Lv Zheng and Aaron Lu (hopefully, that will help people to
uderstand how the ACPI subsystem works) and one outdated doc is
updated by Hanjun Guo.
- Assorted ACPI updates
We finally nailed down the IA-64 issue that was the reason for
reverting commit 9f29ab11dd ("ACPI / scan: do not match drivers
against objects having scan handlers"), so we can fix it and move
the ACPI scan handler check added to the ACPI video driver back to
the core.
A mechanism for adding CMOS RTC address space handlers is
introduced by Lan Tianyu to allow some EC-related breakage to be
fixed on some systems.
A spec-compliant implementation of acpi_os_get_timer() is added by
Mika Westerberg.
The evaluation of _STA is added to do_acpi_find_child() to avoid
situations in which a pointer to a disabled device object is
returned instead of an enabled one with the same _ADR value. From
Jeff Wu.
Intel BayTrail PCH (Platform Controller Hub) support is added to
the ACPI driver for Intel Low-Power Subsystems (LPSS) and that
driver is modified to work around a couple of known BIOS issues.
Changes from Mika Westerberg and Heikki Krogerus.
The EC driver is fixed by Vasiliy Kulikov to use get_user() and
put_user() instead of dereferencing user space pointers blindly.
Code cleanups are made by Bjorn Helgaas, Nicholas Mazzuca and Toshi
Kani.
- Assorted power management updates
The "runtime idle" helper routine is changed to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows us to reduce the
overall code bloat a bit (by dropping some code that's not
necessary any more after that modification).
The runtime PM documentation is updated by Alan Stern (to reflect
the "runtime idle" behavior change).
New trace points for PM QoS are added by Sahara
(<keun-o.park@windriver.com>).
PM QoS documentation is updated by Lan Tianyu.
Code cleanups are made and minor issues are addressed by Bernie
Thompson, Bjorn Helgaas, Julius Werner, and Shuah Khan.
- devfreq updates
New driver for the Exynos5-bus device from Abhilash Kesavan.
Minor cleanups, fixes and MAINTAINERS update from MyungJoo Ham,
Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and Wei Yongjun.
- OMAP power management updates
Adaptive Voltage Scaling (AVS) SmartReflex voltage control driver
updates from Andrii Tseglytskyi and Nishanth Menon."
* tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
cpufreq: Fix cpufreq regression after suspend/resume
ACPI / PM: Fix possible NULL pointer deref in acpi_pm_device_sleep_state()
PM / Sleep: Warn about system time after resume with pm_trace
cpufreq: don't leave stale policy pointer in cdbs->cur_policy
acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
cpufreq: make sure frequency transitions are serialized
ACPI: implement acpi_os_get_timer() according the spec
ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
ACPI: Add CMOS RTC Operation Region handler support
ACPI / processor: Drop unused variable from processor_perflib.c
cpufreq: tegra: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: s3c64xx: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: omap: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: imx6q: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: exynos: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: dbx500: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: davinci: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: arm-big-little: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
...
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
These are changes that arrived a little late before the merge
window or that have multiple dependencies on previous branches
so they did not fit into one of the earlier ones. There
are 10 branches merged here, a total of 39 non-merge commits.
Contents are a mixed bag for the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and
the TI 'Nspire' graphing calculator. These should have
been in the 'soc' branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos,
which is based on the other exynos branches to avoid
conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM
Conflicts:
* In Kconfig.debug, various additions trivially conflict,
the list should be kept in alphabetical order when
resolving.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=cRu2
-----END PGP SIGNATURE-----
Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Arnd Bergmann:
"These are changes that arrived a little late before the merge window
or that have multiple dependencies on previous branches so they did
not fit into one of the earlier ones. There are 10 branches merged
here, a total of 39 non-merge commits. Contents are a mixed bag for
the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and the TI
'Nspire' graphing calculator. These should have been in the 'soc'
branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos, which is based
on the other exynos branches to avoid conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: bail out on alien cpus
ARM: davinci: da850: adopt to pinctrl-single change for configuring multiple pins
serial: sh-sci: Initialise variables before access in sci_set_termios()
ARM: stih41x: Add B2020 board support
ARM: stih41x: Add B2000 board support
ARM: sti: Add DEBUG_LL console support
ARM: sti: Add STiH416 SOC support
ARM: sti: Add STiH415 SOC support
ARM: msm: Migrate to common clock framework
ARM: msm: Make proc_comm clock control into a platform driver
ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
ARM: msm: Remove clock-7x30.h include file
ARM: msm: Remove custom clk_set_{max,min}_rate() API
ARM: msm: Remove custom clk_set_flags() API
msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
msm: iommu: Convert to clk_prepare/unprepare
msm_sdcc: Convert to clk_prepare/unprepare
usb: otg: msm: Convert to clk_prepare/unprepare
msm_serial: Use devm_clk_get() and properly return errors
msm_serial: Convert to clk_prepare/unprepare
...
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
These are various bug fixes that were not considered important enough
for merging into 3.10. The majority of the ARM fixes are for the OMAP
and at91 platforms, and there is another set of bug fixes for device
drivers that resolve 'randconfig' build errors and that the subsystem
maintainers either did not pick up or preferred to get merged through
the arm-soc tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gNDf
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-cricitical bug fixes from Arnd Bergmann:
"These are various bug fixes that were not considered important enough
for merging into 3.10.
The majority of the ARM fixes are for the OMAP and at91 platforms, and
there is another set of bug fixes for device drivers that resolve
'randconfig' build errors and that the subsystem maintainers either
did not pick up or preferred to get merged through the arm-soc tree."
* tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: at91/PMC: use at91_usb_rate() for UTMI PLL
ARM: at91/PMC: fix at91sam9n12 USB FS init
ARM: at91/PMC: at91sam9n12 family has a PLLB
ARM: at91/PMC: sama5d3 family doesn't have a PLLB
ARM: tegra: fix section mismatch in tegra_pmc_parse_dt
ARM: mxs: don't select HAVE_PWM
ARM: mxs: stub out mxs_pm_init for !CONFIG_PM
cpuidle: calxeda: select ARM_CPU_SUSPEND
ARM: mvebu: fix length of ethernet registers in mv78260 dtsi
ARM: at91: cpuidle: Fix target_residency
ARM: at91: fix at91_extern_irq usage for non-dt boards
ARM: sirf: use CONFIG_SIRF rather than CONFIG_PRIMA2 where necessary
clocksource: kona: adapt to CLOCKSOURCE_OF_DECLARE change
X.509: do not emit any informational output
mtd: omap2: allow bulding as a module
[SCSI] nsp32: use mdelay instead of large udelay constants
hwrng: bcm2835: fix MODULE_LICENSE tag
ARM: at91: Change the internal SRAM memory type MT_MEMORY_NONCACHED
ARM: at91: Fix link breakage when !CONFIG_PHYLIB
MAINTAINERS: Add exynos filename match to ARM/S5P EXYNOS ARM ARCHITECTURES
...
Elen Song