This patch adds DT bindings documentation for Cirrus Logic
CS4341 DAC.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds board specific bindings required for dais, In particular
for compressed dais and dai direction.
Board specific setup involves setting up some of dais as compressed dais
and also specify direction of any dai. Some of the dais might only
support capture/playback depending on the board level wiring.
These two new dt properties will allow such flexibilty at board level dts.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple-card and simple-scu-card are very similar driver,
but the former is supporting normal sound card,
the latter is supporting DPCM sound card.
We couldn't use normal sound and DPCM sound in same time by
one sound card. This patch merges both sound card into
simple-card. Now we can use both feature on same driver.
simple-card is now supporting .compatible = "simple-scu-audio-card".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-card and audio-graph-scu-card are very similar driver,
but the former is supporting normal sound card,
the latter is supporting DPCM sound card.
We couldn't use normal sound and DPCM sound in same sound card by
audio-graph-card.
This patch merges both feature into it on Documentation.
Now we can use both feature on same driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added documentation for I2S IP core DT bindings.
Signed-off-by: Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the DT binding documentation for axg's SPDIF input.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Introduce protected-clock DT binding to fix breakage on qcom sdm845-mtp
boards where the qspi clks introduced this merge window cause the
firmware on those boards to take down the system if we try to read
the clk registers
- Fix a couple off-by-one errors found by Dan Carpenter
- Handle failure in zynq fixed factor clk driver to avoid using
uninitialized data
-----BEGIN PGP SIGNATURE-----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=t1kp
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A few clk driver fixes this time:
- Introduce protected-clock DT binding to fix breakage on qcom
sdm845-mtp boards where the qspi clks introduced this merge window
cause the firmware on those boards to take down the system if we
try to read the clk registers
- Fix a couple off-by-one errors found by Dan Carpenter
- Handle failure in zynq fixed factor clk driver to avoid using
uninitialized data"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: zynqmp: Off by one in zynqmp_is_valid_clock()
clk: mmp: Off by one in mmp_clk_add()
clk: mvebu: Off by one bugs in cp110_of_clk_get()
arm64: dts: qcom: sdm845-mtp: Mark protected gcc clocks
clk: qcom: Support 'protected-clocks' property
dt-bindings: clk: Introduce 'protected-clocks' property
clk: zynqmp: handle fixed factor param query error
Bindings should use 'reset-gpios', not 'reset-gpio'. The driver needs to
switch to the gpiod consume API to handle this correctly.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bindings should use 'reset-gpios', not 'reset-gpio'. The driver needs to
switch to the gpiod consume API to handle this correctly.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull input updates from Dmitry Torokhov:
"Mostly new IDs for Elan/Synaptics touchpads, plus a few small fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: omap-keypad - fix keyboard debounce configuration
Input: xpad - quirk all PDP Xbox One gamepads
Input: synaptics - enable SMBus for HP 15-ay000
Input: synaptics - add PNP ID for ThinkPad P50 to SMBus
Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15ARR
Input: elan_i2c - add support for ELAN0621 touchpad
Input: hyper-v - fix wakeup from suspend-to-idle
Input: atkbd - clean up indentation issue
Input: st1232 - convert to SPDX identifiers
Input: migor_ts - convert to SPDX identifiers
Input: dt-bindings - fix a typo in file input-reset.txt
Input: cros_ec_keyb - fix button/switch capability reports
Input: elan_i2c - add ELAN0620 to the ACPI table
Input: matrix_keypad - check for errors from of_get_named_gpio()
-----BEGIN PGP SIGNATURE-----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=44JZ
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- Revert a dt-bindings patch whose driver didn't make for 4.20
- fix a kernel oops at vicodec driver
- fix a frame overflow at gspca with was causing regressions on some
cameras, making them to not work
- use the proper type for wait_queue head
- make media request API compatible with 32-bit userspace on 64-bit
kernel
- fix a regression on Kernel 4.19 at dvb-pll
- don't use SPDX headers yet for GFDL
* tag 'media/v4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: mediactl docs: Fix licensing message
media: dvb-pll: don't re-validate tuner frequencies
media: dvb-pll: fix tuner frequency ranges
media: Revert "media: dt-bindings: Document the Rockchip VPU bindings"
media: gspca: fix frame overflow error
media: vicodec: fix memchr() kernel oops
media: cedrus: add action item to the TODO
media: media-request: Add compat ioctl
media: Use wait_queue_head_t for media_request
The example should follow the practice or using a generic node name
instead of the precise programming model, as recommended by the DTSpec.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here are some small USB and PHY driver fixes for 4.20-rc5
Nothing big at all, just the usual handful of USB fixes for reported
issues, along with some gadget and PHY driver bug fixes.
All of these have been in linux-next with no reported issues.
Note, the USB gadget fixes were in linux-next on its own branch, not in
mine, it just got merged into here yesterday and missed linux-next of
today.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXAFfLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn4OwCg1rMrW+r4+OeehFi2wR7wxxP0f1QAnRj/djtD
w3+dT6m3PanQE40d1zi5
=HsrT
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY driver fixes from Greg KH:
"Here are some small USB and PHY driver fixes for 4.20-rc5
Nothing big at all, just the usual handful of USB fixes for reported
issues, along with some gadget and PHY driver bug fixes.
All of these have been in linux-next with no reported issues. Note,
the USB gadget fixes were in linux-next on its own branch, not in
mine, it just got merged into here yesterday and missed linux-next of
today"
* tag 'usb-4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: u_ether: fix unsafe list iteration
USB: omap_udc: fix rejection of out transfers when DMA is used
USB: omap_udc: fix USB gadget functionality on Palm Tungsten E
USB: omap_udc: fix omap_udc_start() on 15xx machines
USB: omap_udc: fix crashes on probe error and module removal
USB: omap_udc: use devm_request_irq()
usb: core: quirks: add RESET_RESUME quirk for Cherry G230 Stream series
USB: usb-storage: Add new IDs to ums-realtek
Revert "usb: dwc3: gadget: skip Set/Clear Halt when invalid"
phy: qcom-qusb2: Fix HSTX_TRIM tuning with fused value for SDM845
phy: qcom-qusb2: Use HSTX_TRIM fused value as is
dt-bindings: phy-qcom-qmp: Fix several mistakes from prior commits
phy: uniphier-pcie: Depend on HAS_IOMEM
A few driver specific fixes here, nothing big or that stands out for
anyone other than the driver users.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlv+uFQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0GN/B/9rkzlaRTNvBepsN3qbDfFotIt2+9T0
as4tDY5t+C6PWHkKaqezTuKzin+fSOpSQ9n8rx2yc9oddwpelDsqLVxUlxRuN+RB
C+UBfls7rP3J8AlYaGFor+N+MjiRuWVpfYW0PbFf1kM8l1fmOP7FC7BB76G1Ketu
3U9DSWeL5YMZq+IIXI3e77f3luq4/bo2DVxNMQ/PL/frbpRIqOVYag5kGFRxYYez
7rcAo68mOCv/85xdqNZ5u2m+xO/fpSYV+CGFXbYvGPizFIGl9REnw+8DE7EVSCo7
xsPsMuj/bE0Gr3frPguZ0XFsOyFB+SVxqMQxQt2zKiEDuLtQYTFmhs9h
=kDIQ
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes here, nothing big or that stands out for
anyone other than the driver users.
The omap2-mcspi fix is for issues that started showing up with a
change in defconfig in this release to make cpuidle get turned on by
default"
* tag 'spi-fix-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: omap2-mcspi: Add missing suspend and resume calls
spi: mediatek: use correct mata->xfer_len when in fifo transfer
spi: uniphier: fix incorrect property items
On startup, applications such as PulseAudio or CRAS enable playback or
capture on all PCM devices to verify that configurations are correct,
and close them immediately. For DMICs, this can result in the clock
being turned off very quickly, which may not compatible with internal
state machine transition requirements.
This patch add a mode-switch delay which will prevent the clock from
being turned off without complying with manufacturer timing
specifications. While the DMIC clock may be controlled at a lower level,
be it with hardware or firmware, applying the delay during the
STOP_TRIGGER phase ensures that there is no race condition, e.g. with
the hardware/firmware turning off the clock earlier
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
McPDM module receives it's functional clock from external source. This
clock is the pdmclk provided by the twl6040 audio IC. If the clock is not
available all register accesses to McPDM fails and the module is not
operational.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dismod property can be used to specify the drive on level of inactive
TX slots.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit da48a6eb82 ("ASoC: rsnd: add SSIU BUSIF support for
Document") updated Documentation for SSIU, but 1) we want to
keep old/deprecated DMA description, 2) it is missing SSIU
subnode properties. This patch tidyup these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
*) Fix updating HSTX_TRIM tuning parameter in qcom-qusb2 PHY driver
*) Fix inconsistencies between dt-bindings and the driver
*) Add "Depend on HAS_IOMEM" uniphier-pcie to avoid randconfig errors
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=wXaJ
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.20-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.20-rc
*) Fix updating HSTX_TRIM tuning parameter in qcom-qusb2 PHY driver
*) Fix inconsistencies between dt-bindings and the driver
*) Add "Depend on HAS_IOMEM" uniphier-pcie to avoid randconfig errors
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-4.20-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: qcom-qusb2: Fix HSTX_TRIM tuning with fused value for SDM845
phy: qcom-qusb2: Use HSTX_TRIM fused value as is
dt-bindings: phy-qcom-qmp: Fix several mistakes from prior commits
phy: uniphier-pcie: Depend on HAS_IOMEM
The correct form is "can be probed", so fix the typo.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
audio-graph-scu-card.c is supporting "convert-rate/channels" which is
used for DPCM.
But, sound card might have multi codecs, and each codec might need
each convert-rate/channels.
This patch supports each codec's convert-rate/channles support.
top node convert-rate/channels will overwrite settings if exist.
It can't support each codec's convert-rate/channels if sound card had
multi codecs without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-scu-card.c is supporting "prefix" which is used to avoid
DAI naming conflict when CPU/Codec matching.
But, sound card might have multi sub-devices, and each codec might need
each prefix.
Now, ASoC is supporting snd_soc_of_parse_node_prefix(), let's support
it on audio-graph-scu-card, too. It is keeping existing DT style.
It can't support each codec's prefix if sound card had multi sub-devices
without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple-scu-card.c is supporting "prefix" which is used to avoid
DAI naming conflict when CPU/Codec matching.
But, sound card might have multi sub-devices, and each codec might need
each prefix.
Now, ASoC is supporting snd_soc_of_parse_node_prefix(), let's support
it on audio-graph-scu-card, too. It is keeping existing DT style.
It can't support each codec's prefix if sound card had multi sub-devices
without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Amplifier may have associated regulator, so add a property for it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On the Allwinner A64 SoC, the audio codec has a built-in headphone
amplifier. This amplifier has a power supply separate from the rest of
the analog audio circuitry.
Add a regulator supply property to handle this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit e4183d3256.
The commit was picked by mistake, as the Rockchip VPU driver
is not ready for inclusion yet, and it's still under discussion.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Simply document new compat strings.
There appears to be no need for a driver updates.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a generic clk property for clks which are not intended to be used by
the OS due to security restrictions put in place by firmware. For
example, on some Qualcomm firmwares reading or writing certain clk
registers causes the entire system to reboot, but on other firmwares
reading and writing those same registers is required to make devices
like QSPI work. Rather than adding one-off properties each time a new
set of clks appears to be protected, let's add a generic clk property to
describe any set of clks that shouldn't be touched by the OS. This way
we never need to register the clks or use them in certain firmware
configurations.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pull networking fixes from David Miller:
1) Fix some potentially uninitialized variables and use-after-free in
kvaser_usb can drier, from Jimmy Assarsson.
2) Fix leaks in qed driver, from Denis Bolotin.
3) Socket leak in l2tp, from Xin Long.
4) RSS context allocation fix in bnxt_en from Michael Chan.
5) Fix cxgb4 build errors, from Ganesh Goudar.
6) Route leaks in ipv6 when removing exceptions, from Xin Long.
7) Memory leak in IDR allocation handling of act_pedit, from Davide
Caratti.
8) Use-after-free of bridge vlan stats, from Nikolay Aleksandrov.
9) When MTU is locked, do not force DF bit on ipv4 tunnels. From
Sabrina Dubroca.
10) When NAPI cached skb is reused, we must set it to the proper initial
state which includes skb->pkt_type. From Eric Dumazet.
11) Lockdep and non-linear SKB handling fix in tipc from Jon Maloy.
12) Set RX queue properly in various tuntap receive paths, from Matthew
Cover.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tuntap: fix multiqueue rx
ipv6: Fix PMTU updates for UDP/raw sockets in presence of VRF
tipc: don't assume linear buffer when reading ancillary data
tipc: fix lockdep warning when reinitilaizing sockets
net-gro: reset skb->pkt_type in napi_reuse_skb()
tc-testing: tdc.py: Guard against lack of returncode in executed command
tc-testing: tdc.py: ignore errors when decoding stdout/stderr
ip_tunnel: don't force DF when MTU is locked
MAINTAINERS: Add entry for CAKE qdisc
net: bridge: fix vlan stats use-after-free on destruction
socket: do a generic_file_splice_read when proto_ops has no splice_read
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
net/sched: act_pedit: fix memory leak when IDR allocation fails
net: lantiq: Fix returned value in case of error in 'xrx200_probe()'
ipv6: fix a dst leak when removing its exception
net: mvneta: Don't advertise 2.5G modes
drivers/net/ethernet/qlogic/qed/qed_rdma.h: fix typo
net/mlx4: Fix UBSAN warning of signed integer overflow
...
rt5663 codec driver will support setting CPVDD and AVDD power supply
from device tree.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Output of pcm3060 codec may be configured as single-ended or differential
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Drop stale DT binding for the arm_big_little_dt driver removed
recently (Sudeep Holla).
- Fix up error handling in the imx6q cpufreq driver to make it
report voltage scaling failures (Anson Huang).
- Fix two issues in the cpufreq documentation (Viresh Kumar,
Zhao Wei Liew).
- Fix ARM cpuidle driver initialization regression from the 4.19
time frame and rework the driver registration part of it to
simplify code (Ulf Hansson).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=RD7r
-----END PGP SIGNATURE-----
Merge tag 'pm-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These remove a stale DT entry left behind after recent removal of a
cpufreq driver without users, fix up error handling in the imx6q
cpufreq driver, fix two issues in the cpufreq documentation, and
update the ARM cpufreq driver.
Specifics:
- Drop stale DT binding for the arm_big_little_dt driver removed
recently (Sudeep Holla).
- Fix up error handling in the imx6q cpufreq driver to make it report
voltage scaling failures (Anson Huang).
- Fix two issues in the cpufreq documentation (Viresh Kumar, Zhao Wei
Liew).
- Fix ARM cpuidle driver initialization regression from the 4.19 time
frame and rework the driver registration part of it to simplify
code (Ulf Hansson)"
* tag 'pm-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ARM: cpuidle: Convert to use cpuidle_register|unregister()
ARM: cpuidle: Don't register the driver when back-end init returns -ENXIO
dt-bindings: cpufreq: remove stale arm_big_little_dt entry
Documentation: cpufreq: Correct a typo
cpufreq: imx6q: add return value check for voltage scale
Documentation: cpu-freq: Frequencies aren't always sorted
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEENrCndlB/VnAEWuH5k9IU1zQoZfEFAlvlt0gTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCT0hTXNChl8bMDB/9ElLCS/uh3CznHeX8w24t/LldHoy0q
eposGQ6+uWV/R7lUfNNUtIAcoSxzuOyXSMh9skz8NdExdQ0/9osnvNWemKTGrfhm
ndCVmMd7dMoWX2m1VTJ2jrij3MKPe8HmUei+kB9PrhHFNwofNSOvw2dEVjJDSwUW
gAvs6K/KrHh5ncd9O3JfaXqc9Cs95o0dz4U4AGZ68UjUemx1AmDse2q3JVPQcxn0
muXoWWFXBbKob/0qpFG0xP9ssdq75AL58dlEqRV+64EMgqWcgvdoPxGGIBbP4t0x
zMwE3hCaoC7Uogr28tnQrf4kSm5IC33AiMQDKmBQRtzFLxtCI1wE71M4
=eM20
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.20-20181109' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-11-09
this is a pull request of 20 patches for net/master.
First we have a patch by Oliver Hartkopp which changes the raw socket's
raw_sendmsg() to return an error value if the user tries to send a CANFD
frame to a CAN-2.0 device.
The next two patches are by Jimmy Assarsson and fix potential problems
in the kvaser_usb driver.
YueHaibing's patches for the ucan driver fix a compile time warning and
remove a duplicate include.
Eugeniu Rosca patch adds more binding documentation to the rcar_can
driver bindings. The next two patches are by Fabrizio Castro for the
rcar_can driver and fixes a problem in the driver's probe function and
document the r8a774a1 binding.
Lukas Wunner's patch fixes a recpetion problem in hi311x driver by
switching from edge to level triggered interruts.
The next three patches all target the flexcan driver. Pankaj Bansal's
patch unconditionally unlocks the last mailbox used for RX. Alexander
Stein provides a better workaround for a hardware limitation when
sending RTR frames, by using the last mailbox for TX, resulting in fewer
lost frames. The patch by me simplyfies the driver, by making a runtime
value a compile time constant.
The following 4 patches are by me and provide the groundwork for the
next patches by Oleksij Rempel. To avoid code duplication common code in
the common CAN driver infrastructure is factured out and error handling
is cleaned up.
The next 4 patches are by Oleksij Rempel and fix the problem in the
flexcan driver that other processes see TX frames arrive out of order
with ragards to a RX'ed frame (which are send by a different system on
the CAN bus as the result of our TX frame).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Digging through the "phy-qcom-qmp" showed me many inconsistencies
between the bindings and the reality of the driver. Let's fix them
all.
* In commit 2d66eab183 ("dt-bindings: phy: qmp: Add support for QMP
phy in IPQ8074") we probably should have explicitly listed that
there are no clocks for this PHY and also added the reset names in
alphabetical order. You can see that there are no clocks in the
driver where "clk_list" is NULL.
* In commit 8587b220f0 ("dt-bindings: phy-qcom-qmp: Update bindings
for QMP V3 USB PHY") we probably should have listed the resets for
this new PHY and also removed the "(Optional)" marking for the "cfg"
reset since PHYs that need "cfg" really do need it. It's just that
not all PHYs need it.
* In commit 7f08020741 ("dt-bindings: phy-qcom-qmp: Update bindings
for sdm845") we forgot to update one instance of the string
"qcom,qmp-v3-usb3-phy" to be "qcom,sdm845-qmp-usb3-phy". Let's fix
that. We should also have added "qcom,sdm845-qmp-usb3-uni-phy" to
the clock-names and reset-names lists.
* In commit 99c7c7364b ("dt-bindings: phy-qcom-qmp: Add UFS phy
compatible string for sdm845") we should have added the set of
clocks and resets for "qcom,sdm845-qmp-ufs-phy". These were taken
from the driver.
* Cleanup the wording for what properties child nodes have to make it
more obvious which types of PHYs need clocks and resets. This was
sorta implicit in the "-names" description but I found myself
confused.
* As per the code not all "pcie qmp phys" have resets. Specifically
note that the "has_lane_rst" property in the driver is false for
"ipq8074-qmp-pcie-phy". Thus make it clear exactly which PHYs need
child nodes with resets.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pull i2c updates from Wolfram Sang:
"I2C has one bugfix (qcom-geni driver), one arch enablement (i2c-omap
driver, no code change), and a new driver (nvidia-gpu) this time"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
usb: typec: ucsi: add support for Cypress CCGx
i2c: nvidia-gpu: make pm_ops static
i2c: add i2c bus driver for NVIDIA GPU
i2c: qcom-geni: Fix runtime PM mismatch with child devices
MAINTAINERS: Add entry for i2c-omap driver
i2c: omap: Enable for ARCH_K3
dt-bindings: i2c: omap: Add new compatible for AM654 SoCs
AM654 SoCs have same I2C IP as OMAP SoCs. Add new compatible to
handle AM654 SoCs. While at that reformat the existing compatible list
for older SoCs to list one valid compatible per line.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the hi3110 shares the SPI bus with another traffic-intensive device
and packets are received in high volume (by a separate machine sending
with "cangen -g 0 -i -x"), reception stops after a few minutes and the
counter in /proc/interrupts stops incrementing. Bus state is "active".
Bringing the interface down and back up reconvenes the reception. The
issue is not observed when the hi3110 is the sole device on the SPI bus.
Using a level-triggered interrupt makes the issue go away and lets the
hi3110 successfully receive 2 GByte over the course of 5 days while a
ks8851 Ethernet chip on the same SPI bus handles 6 GByte of traffic.
Unfortunately the hi3110 datasheet is mum on the trigger type. The pin
description on page 3 only specifies the polarity (active high):
http://www.holtic.com/documents/371-hi-3110_v-rev-kpdf.do
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Document RZ/G2M (r8a774a1) SoC specific bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Document the support for rcar_can on R8A77965 SoC devices.
Add R8A77965 to the list of SoCs which require the "assigned-clocks" and
"assigned-clock-rates" properties (thanks, Sergei).
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Most of the ARM platforms used v2 OPP bindings to support big-little
configurations. This arm_big_little_dt binding is incomplete and was
never used.
Commit f174e49e49 (cpufreq: remove unused arm_big_little_dt driver)
removed the driver supporting this binding, but the binding was left
unnoticed, so let's get rid of it now.
Fixes: f174e49e49 (cpufreq: remove unused arm_big_little_dt driver)
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds TDM Split mode support. rsnd driver is assuming
audio-graph-scu-card is used for Sound Card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gen2 has BUSIF0-3, Gen3 has BUSIF0-7 on some SSIU.
Current driver is assuming it is using BUSIF0 as default.
Thus, SSI is attaching SSIU (with BUSIF0) by using rsnd_ssiu_attach().
But, TDM split mode also needs other BUSIF to use it.
This patch adds missing SSIU BUSIFx support.
BUSIF is handled by SSIU instead of SSI anymore.
Thus, its settings no longer needed on SSI node on DT.
This patch removes its settings from Document, but driver is still
keeping compatibility. Thus, old DT style is still working.
But, to avoid confusing, it doesn't indicate old compatibility things on
Document. New SoC should have SSIU on DT from this patch.
1) old style DT is still supported (= no rcar_sound,ssiu node on DT)
2) If ssiu is not indicated on playback/capture,
BUSIF0 will be used as default
playback = <&ssi3>; /* ssiu30 will be selected */
3) you can select own ssiu
playback = <&ssi32 &ssi3>; /* ssiu32 will be selected */
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It has duplicated DT example code on Document.
This patch tidyup these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix RZ/G2E part number from its description.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull more timer updates from Thomas Gleixner:
"A set of commits for the new C-SKY architecture timers"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dt-bindings: timer: gx6605s SOC timer
clocksource/drivers/c-sky: Add gx6605s SOC system timer
dt-bindings: timer: C-SKY Multi-processor timer
clocksource/drivers/c-sky: Add C-SKY SMP timer
Alexander Shiyan