Not all iscsi drivers support ibft. For drivers like be2iscsi
that do not but are bootable through a vendor firmware specific
format/process this patch moves the sysfs interface from the ibft code
to a lib module. This then allows userspace tools to search for iscsi boot
info in a common place and in a common format.
ibft iscsi boot info is exported in the same place as it was
before: /sys/firmware/ibft.
vendor/fw boot info gets export in /sys/firmware/iscsi_bootX, where X is the
scsi host number of the HBA. Underneath these parent dirs, the
target, ethernet, and initiator dirs are the same as they were before.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Peter Jones <pjones@redhat.com>
For machines with IBFT 1.03 do scan the ACPI table for 'iBFT'
or for 'IBFT'. If the machine is in UEFI mode, only do the ACPI
table scan. For all other machines (pre IBFT 1.03) do
a memory scan if not found in the ACPI tables.
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Tested-by: Mike Christie <michaelc@cs.wisc.edu>
- Use struct acpi_table_ibft instead of struct ibft_table_header
- Don't do reserve_ibft_region() on UEFI machines (section 1.4.3.1)
- If ibft_addr isn't initialized when ibft_init() is called, check for
ACPI-based tables.
- Fix compiler error when CONFIG_ACPI is not defined.
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86: Fix double enable_IR_x2apic() call on SMP kernel on !SMP boards
x86: Increase CONFIG_NODES_SHIFT max to 10
ibft, x86: Change reserve_ibft_region() to find_ibft_region()
x86, hpet: Fix bug in RTC emulation
x86, hpet: Erratum workaround for read after write of HPET comparator
bootmem, x86: Fix 32bit numa system without RAM on node 0
nobootmem, x86: Fix 32bit numa system without RAM on node 0
x86: Handle overlapping mptables
x86: Make e820_remove_range to handle all covered case
x86-32, resume: do a global tlb flush in S4 resume
This allows arch code could decide the way to reserve the ibft.
And we should reserve ibft as early as possible, instead of BOOTMEM
stage, in case the table is in RAM range and is not reserved by BIOS
(this will often be the case.)
Move to just after find_smp_config().
Also when CONFIG_NO_BOOTMEM=y, We will not have reserve_bootmem() anymore.
-v2: fix typo about ibft pointed by Konrad Rzeszutek Wilk <konrad@darnok.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4BB510FB.80601@kernel.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Peter Jones <pjones@redhat.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
CC: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A memmap is a directory in sysfs which includes 3 text files: start, end
and type. For example:
start: 0x100000
end: 0x7e7b1cff
type: System RAM
Interface firmware_map_add was not called explicitly. Remove it and add
function firmware_map_add_hotplug as hotplug interface of memmap.
Each memory entry has a memmap in sysfs, When we hot-add new memory, sysfs
does not export memmap entry for it. We add a call in function add_memory
to function firmware_map_add_hotplug.
Add a new function add_sysfs_fw_map_entry() to create memmap entry, it
will be called when initialize memmap and hot-add memory.
[akpm@linux-foundation.org: un-kernedoc a no longer kerneldoc comment]
Signed-off-by: Shaohui Zheng <shaohui.zheng@intel.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert netmask to __be32 and format it with %pI4
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Konrad Rzeszutek <ketuzsezr@darnok.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Use the %pM kernel extension to display the MAC address.
Also, remove the 'mac' variable and use nic->mac directly.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the EDD depend on !ia64 (and assuming that only ia64,
x86, x86_64 will be including this Kconfig), have EDD depend on the only
arches which can support this code. This should allow all other arches to
cleanly include the firmware Kconfig.
Also simplify the x86 string used by FIRMWARE_MEMMAP to match EDD.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unfortunately, one cannot hold on to the struct firmware
that request_firmware_nowait() hands off, which is needed
in some cases. Allow this by requiring the callback to
free it (via release_firmware).
Additionally, give it a gfp_t parameter -- all the current
users call it from a GFP_KERNEL context so the GFP_ATOMIC
isn't necessary. This also marks an API break which is
useful in a sense, although that is obviously not the
primary purpose of this change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: Abhay Salunke <abhay_salunke@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The purpose of dmi->ident is twofold - it may be used by DMI callback
functions when composing log messages; it is also used to determine
end of DMI table in dmi_check_system() and dmi_first_match(). However,
in case when callbacks are not interested in using ident at all it just
wastes memory. Let's make entries with empty first match slot serve as
end-of-table markers instead.
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In virtual environments (namely, Xen Dom0) virt <-> phys and
virt <-> isa-bus translations cannot be freely interchanged (and
even outside such environments it is not really correct to do so).
When looking at memory below 1M, the latter translations should
always be used.
iscsi_ibft_find.c part from: Martin Wilck <martin.wilck@ts.fujitsu.com>.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <ketuzsezs@darnok.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since alloc_bootmem() will never return inaccessible (via virtual
addressing) memory anyway, using the ..._low() variant only makes sense
when the physical address range of the allocated memory must fulfill
further constraints, espacially since on 64-bits (or more generally in all
cases where the pools the two variants allocate from are than the full
available range.
Probably the use in alloc_tce_table() could also be eliminated (based on
code inspection of pci-calgary_64.c), but that seems too risky given I
know nothing about that hardware and have no way to test it.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are cases where full date information is required instead of
just the year. Add month and day parsing to dmi_get_year() and rename
it to dmi_get_date().
As the original function only required '/' followed by any number of
parseable characters at the end of the string, keep that behavior to
avoid upsetting existing users.
The new function takes dates of format [mm[/dd]]/yy[yy]. Year, month
and date are checked to be in the ranges of [1-9999], [1-12] and
[1-31] respectively and any invalid or out-of-range component is
returned as zero.
The dummy implementation is updated accordingly but the return value
is updated to indicate field not found which is consistent with how
other dummy functions behave.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Year parsing in dmi_get_year() had the following two bugs.
* "00" is treated as invalid instead of 2000 because zero return from
simple_strtoul() is treated as error.
* "0N" where N >= 8 is treated as invalid of 200N because the leading
0 is considered to specify octal.
Fix the above two bugs by using endptr to detect invalid number and
forcing decimal.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It is generally agreed that it would be beneficial for u64 to be an
unsigned long long on all architectures. ia64 (in common with several
other 64-bit architectures) currently uses unsigned long. Migrating
piecemeal is too painful; this giant patch fixes all compilation warnings
and errors that come as a result of switching to use int-ll64.h.
Note that userspace will still see __u64 defined as unsigned long. This
is important as it affects C++ name mangling.
[Updated by Tony Luck to change efi.h:efi_freemem_callback_t to use
u64 for start/end rather than unsigned long]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13484
Peer reported:
| The bug is introduced from kernel 2.6.27, if E820 table reserve the memory
| above 4G in 32bit OS(BIOS-e820: 00000000fff80000 - 0000000120000000
| (reserved)), system will report Int 6 error and hang up. The bug is caused by
| the following code in drivers/firmware/memmap.c, the resource_size_t is 32bit
| variable in 32bit OS, the BUG_ON() will be invoked to result in the Int 6
| error. I try the latest 32bit Ubuntu and Fedora distributions, all hit this
| bug.
|======
|static int firmware_map_add_entry(resource_size_t start, resource_size_t end,
| const char *type,
| struct firmware_map_entry *entry)
and it only happen with CONFIG_PHYS_ADDR_T_64BIT is not set.
it turns out we need to pass u64 instead of resource_size_t for that.
[akpm@linux-foundation.org: add comment]
Reported-and-tested-by: Peer Chen <pchen@nvidia.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Community reported one SB600 SATA issue(BZ #9412), which led to 64 bit
DMA disablement for all SB600 revisions by driver maintainers with
commits c7a42156d9 and
4cde32fc4b.
But the root cause is ASUS M2A-VM system BIOS bug in old revisions
like 0901, while forcing into 32bit DMA happens to work as workaround.
Now it's time to withdraw 4cde32fc4b
so as to restore the SB600 SATA 64bit DMA capability.
This patch is also adding the workaround for M2A-VM old BIOS revisions,
but users are suggested to upgrade their system BIOS to the latest one
if they meet this issue.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the display of a few fields in the iBFT NIC attribute structure in
sysfs.
Ensure that, if the DHCP IP address and the subnet mask for the interface
is present in the iBFT NIC structure, the corresponding entries are
created in sysfs tree for the device. This would hence create the
additional entries in the tree based on the iBFT table and would not
delete any existing entries.
Signed-off-by: Ashutosh Naik <ashutosh.naik@gmail.com>
Cc: Vishnu V <vishnu@chelsio.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At the moment, dmi_walk() lacks flexibility, users can't pass data to
the callback function. Add a pointer for private data to make this
function more flexible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Roland Dreier <rolandd@cisco.com>
Since I don't work for SUSE any more and the bwalle@suse.de address is
invalid, correct it in the copyright headers and documentation.
Signed-off-by: Bernhard Walle <bernhard.walle@gmx.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/firmware/iscsi_ibft.c: In function ‘ibft_init’:
drivers/firmware/iscsi_ibft.c:942: warning: format ‘%lx’ expects type ‘long unsigned int’, but argument 2 has type ‘phys_addr_t’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information. However, only the on-board controlles should
be blacklisted and their PCI slot numbers can be used for this
purpose. Unfortunately the existing interface for checking DMI
information of the system is not very convenient for this purpose,
because to use it, we would have to define special callback functions
or create a separate struct dmi_system_id table for each blacklisted
system.
To overcome this difficulty introduce a new function
dmi_first_match() returning a pointer to the first entry in an array
of struct dmi_system_id elements that matches the system DMI
information. Then, we can use this pointer to access the entry's
.driver_data field containing the additional information, such as
the PCI slot number, allowing us to do the desired blacklisting.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reading 0 bytes from /sys/devices/platform/dell_rbu/image_type or
/sys/devices/platform/dell_rbu/packet_size by an ordinary user causes an
oops.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Building an allnoconfig kernel, sparse asked whether these could be
static, so I checked, and they are only used in the file where they are
declared.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dcdbas code allows calls to be made into the firmware on Dell systems.
Exporting this to other drivers allows them to implement Dell-specific
functionality in a safe way.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing kernel-doc notation:
drivers/firmware/dmi_scan.c:475: No description found for parameter 'str'
drivers/firmware/dmi_scan.c:592: No description found for parameter 'f'
drivers/firmware/dmi_scan.c:592: No description found for parameter 'str'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a wrapper for testing system_info which will handle also NULL
system infos.
This will be used by the ata PIIX driver.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
As we've lost our trivial maintainer for the moment I'll send this
directly. Only touches a comment
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: Should permit VMware detection on older platforms where the
vendor is changed. Could theoretically cause a regression if some
weird serial number scheme contains the string "VMware" by pure
chance. Seems unlikely, especially with the mixed case.
In some user configured cases, VMware may choose not to put a VMware specific
DMI string, but the product serial key is always there and is VMware specific.
Add a interface to check the serial key, when checking for VMware in the DMI
information.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The iscsi_ibft.c changes are almost certainly a bugfix as the
pointer 'ip' is a u8 *, so they never print the last 8 bytes
of the IPv6 address, and the eight bytes they do print have
a zero byte with them in each 16-bit word.
Other than that, this should cause no difference in functionality.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tejun's commit 7b595756ec made sysfs
attribute->owner unnecessary. But the field was left in the structure to
ease the merge. It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!
This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 . We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test. Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.
akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'. But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.
[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes the following needlessly global functions static:
- ibft_attr_show_initiator()
- ibft_attr_show_nic()
- ibft_attr_show_target()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Konrad Rzeszutek <ketuzsezr@darnok.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It happened to me recently that i added a dmi_check_system() quirk
in a too early codepath, and it was silently ignored because all the
DMI tables and strings were still empty.
As this situation is clearly a programming error / kernel bug,
warn when it happens, instead of silently ignoring quirks.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I got this patch through Red Hat's bugzilla from the bug submitter and
patch creator. I have just fixed it up so it applies without fuzz to
upstream kernels.
Original patch and description from Shyam kumar Iyer:
The issue [ibft module not displaying targets with short names] is because
of an offset calculatation error in the iscsi_ibft.c code. Due to this
error directory structure for the target in /sys/firmware/ibft does not
get created and so the initiator is unable to connect to the target.
Note that this bug surfaced only with an name that had a short section at
the end. eg: "iqn.1984-05.com.dell:dell". It did not surface when the
iqn's had a longer section at the end. eg:
"iqn.2001-04.com.example:storage.disk2.sys1.xyz"
So, the eot_offset was calculated such that an extra 48 bytes i.e. the
size of the ibft_header which has already been accounted was subtracted
twice.
This was not evident with longer iqn names because they would overshoot
the total ibft length more than 48 bytes and thus would escape the bug.
Signed-off-by: Shyam Kumar Iyer <shyam_iyer@dell.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Konrad Rzeszutek <konrad@virtualiron.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various cleanup the drivers/firmware/memmap (after review by AKPM):
- fix kdoc to conform to the standard
- move kdoc from header to implementation files
- remove superfluous WARN_ON() after kmalloc()
- WARN_ON(x); if (!x) -> if(!WARN_ON(x))
- improve some comments
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix firmware/memmap printk format warnings:
drivers/firmware/memmap.c:156: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/firmware/memmap.c:161: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Bernhard Walle <bwalle@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Replace previous instances of the cpumask_of_cpu_ptr* macros
with a the new (lvalue capable) generic cpumask_of_cpu().
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* This patch replaces the dangerous lvalue version of cpumask_of_cpu
with new cpumask_of_cpu_ptr macros. These are patterned after the
node_to_cpumask_ptr macros.
In general terms, if there is a cpumask_of_cpu_map[] then a pointer to
the cpumask_of_cpu_map[cpu] entry is used. The cpumask_of_cpu_map
is provided when there is a large NR_CPUS count, reducing
greatly the amount of code generated and stack space used for
cpumask_of_cpu(). The pointer to the cpumask_t value is needed for
calling set_cpus_allowed_ptr() to reduce the amount of stack space
needed to pass the cpumask_t value.
If there isn't a cpumask_of_cpu_map[], then a temporary variable is
declared and filled in with value from cpumask_of_cpu(cpu) as well as
a pointer variable pointing to this temporary variable. Afterwards,
the pointer is used to reference the cpumask value. The compiler
will optimize out the extra dereference through the pointer as well
as the stack space used for the pointer, resulting in identical code.
A good example of the orthogonal usages is in net/sunrpc/svc.c:
case SVC_POOL_PERCPU:
{
unsigned int cpu = m->pool_to[pidx];
cpumask_of_cpu_ptr(cpumask, cpu);
*oldmask = current->cpus_allowed;
set_cpus_allowed_ptr(current, cpumask);
return 1;
}
case SVC_POOL_PERNODE:
{
unsigned int node = m->pool_to[pidx];
node_to_cpumask_ptr(nodecpumask, node);
*oldmask = current->cpus_allowed;
set_cpus_allowed_ptr(current, nodecpumask);
return 1;
}
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds /sys/firmware/memmap interface that represents the BIOS
(or Firmware) provided memory map. The tree looks like:
/sys/firmware/memmap/0/start (hex number)
end (hex number)
type (string)
... /1/start
end
type
With the following shell snippet one can print the memory map in the same form
the kernel prints itself when booting on x86 (the E820 map).
--------- 8< --------------------------
#!/bin/sh
cd /sys/firmware/memmap
for dir in * ; do
start=$(cat $dir/start)
end=$(cat $dir/end)
type=$(cat $dir/type)
printf "%016x-%016x (%s)\n" $start $[ $end +1] "$type"
done
--------- >8 --------------------------
That patch only provides the needed interface:
1. The sysfs interface.
2. The structure and enumeration definition.
3. The function firmware_map_add() and firmware_map_add_early()
that should be called from architecture code (E820/EFI, for
example) to add the contents to the interface.
If the kernel is compiled without CONFIG_FIRMWARE_MEMMAP, the interface does
nothing without cluttering the architecture-specific code with #ifdef's.
The purpose of the new interface is kexec: While /proc/iomem represents
the *used* memory map (e.g. modified via kernel parameters like 'memmap'
and 'mem'), the /sys/firmware/memmap tree represents the unmodified memory
map provided via the firmware. So kexec can:
- use the original memory map for rebooting,
- use the /proc/iomem for setting up the ELF core headers for kdump
case that should only represent the memory of the system.
The patch has been tested on i386 and x86_64.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Greg KH <gregkh@suse.de>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: kexec@lists.infradead.org
Cc: yhlu.kernel@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The "dmi.h" file did not state anywhere in the file what "DMI" was.
For those who know, it's obvious. For the rest of us, I added a
brief opening comment.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a kernel parameter option to 'edd' to enable/disable BIOS Enhanced Disk
Drive Services. CONFIG_EDD_OFF disables EDD while still compiling EDD into
the kernel. Default behavior can be forced using 'edd=on' or 'edd=off' as
a kernel parameter.
[akpm@linux-foundation.org: fix kernel-parameters.txt]
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Doug Warzecha <Douglas_Warzecha@dell.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
Add /sysfs/firmware/ibft/[initiator|targetX|ethernetX] directories along with
text properties which export the the iSCSI Boot Firmware Table (iBFT)
structure.
What is iSCSI Boot Firmware Table? It is a mechanism for the iSCSI tools to
extract from the machine NICs the iSCSI connection information so that they
can automagically mount the iSCSI share/target. Currently the iSCSI
information is hard-coded in the initrd. The /sysfs entries are read-only
one-name-and-value fields.
The usual set of data exposed is:
# for a in `find /sys/firmware/ibft/ -type f -print`; do echo -n "$a: "; cat $a; done
/sys/firmware/ibft/target0/target-name: iqn.2007.com.intel-sbx44:storage-10gb
/sys/firmware/ibft/target0/nic-assoc: 0
/sys/firmware/ibft/target0/chap-type: 0
/sys/firmware/ibft/target0/lun: 00000000
/sys/firmware/ibft/target0/port: 3260
/sys/firmware/ibft/target0/ip-addr: 192.168.79.116
/sys/firmware/ibft/target0/flags: 3
/sys/firmware/ibft/target0/index: 0
/sys/firmware/ibft/ethernet0/mac: 00:11:25:9d:8b:01
/sys/firmware/ibft/ethernet0/vlan: 0
/sys/firmware/ibft/ethernet0/gateway: 192.168.79.254
/sys/firmware/ibft/ethernet0/origin: 0
/sys/firmware/ibft/ethernet0/subnet-mask: 255.255.252.0
/sys/firmware/ibft/ethernet0/ip-addr: 192.168.77.41
/sys/firmware/ibft/ethernet0/flags: 7
/sys/firmware/ibft/ethernet0/index: 0
/sys/firmware/ibft/initiator/initiator-name: iqn.2007-07.com:konrad.initiator
/sys/firmware/ibft/initiator/flags: 3
/sys/firmware/ibft/initiator/index: 0
For full details of the IBFT structure please take a look at:
ftp://ftp.software.ibm.com/systems/support/system_x_pdf/ibm_iscsi_boot_firmware_table_v1.02.pdf
[akpm@linux-foundation.org: fix build]
Signed-off-by: Konrad Rzeszutek <konradr@linux.vnet.ibm.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Use new set_cpus_allowed_ptr() function added by previous patch,
which instead of passing the "newly allowed cpus" cpumask_t arg
by value, pass it by pointer:
-int set_cpus_allowed(struct task_struct *p, cpumask_t new_mask)
+int set_cpus_allowed_ptr(struct task_struct *p, const cpumask_t *new_mask)
* Modify CPU_MASK_ALL
Depends on:
[sched-devel]: sched: add new set_cpus_allowed_ptr function
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
In 2.6.14 a patch was merged which switching the order of the ipmi device
naming from in-order-of-discovery over to reverse-order-of-discovery.
So on systems with multiple BMC interfaces, the ipmi device names are being
created in reverse order relative to how they are discovered on the system
(e.g. on an IBM x3950 multinode server with N nodes, the device name for the
BMC in the first node is /dev/ipmiN-1 and the device name for the BMC in the
last node is /dev/ipmi0, etc.).
The problem is caused by the list handling routines chosen in dmi_scan.c.
Using list_add() causes the multiple ipmi devices to be added to the device
list using a stack-paradigm and so the ipmi driver subsequently pulls them off
during initialization in LIFO order. This patch changes the
dmi_save_ipmi_device() list handling paradigm to a queue, thereby allowing the
ipmi driver to build the ipmi device names in the order in which they are
found on the system.
Signed-off-by: Carol Hebert <cah@us.ibm.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding the same item to a given linked list more than once is guaranteed
to break and corrupt the list. This is however what we do in dmi_scan
since commit 79da472111 ("x86: fix DMI out
of memory problems").
Given that there is absolutely no interest in saving empty OEM strings
anyway, I propose the simple and efficient fix below: we discard the empty
OEM strings altogether.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Parag Warudkar <parag.warudkar@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we gather on-board devices from both DMI types 10 and 41, there is
a possibility that we list the same device twice. In order to not confuse
drivers, and also to save memory, make sure that we do not add duplicate
devices to the dmi_devices list.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From version 2.6 of the SMBIOS standard, type 10 (On Board Devices
Information) becomes obsolete. The reason for this is that no further
fields can be added to this structure without adversely affecting existing
software's ability to properly parse the data.
Therefore type 41 (Onboard Devices Extended Information) was added.
The structure is as follows:
struct smbios_type_41 {
u8 type;
u8 length;
u16 handle;
u8 reference_designation_string;
u8 device_type; /* same device type as in type 10 */
u8 device_type_instance;
u16 segment_group_number;
u8 bus_number;
u8 device_function_number;
};
For more info: http://www.dmtf.org/standards/smbios
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let drivers walk the DMI table for their own needs. Some drivers need
data stored in OEM-specific DMI records for proper operation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
DMI autoload dcdbas on all Dell systems.
This looks for BIOS Vendor or System Vendor == Dell, so this should
work for systems both Dell-branded and those Dell builds but brands
for others. It causes udev to load the dcdbas module at startup,
which is used by tools called by HAL for wireless control and
backlight control, among other uses.
Thanks to Kay Sievers for figuring out how to do this with a single alias.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use existing dmi_get_system_info(),
Delete duplicate dmi_get_slot()
Spotted-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Len Brown <len.brown@intel.com>
People with HP Desktops (including me) encounter couple of DMI errors
during boot - dmi_save_oem_strings_devices: out of memory and
dmi_string: out of memory.
On some HP desktops the DMI data include OEM strings (type 11) out of
which only few are meaningful and most other are empty. DMI code
religiously creates copies of these 27 strings (65 bytes each in my
case) and goes OOM in dmi_string().
If DMI_MAX_DATA is bumped up a little then it goes and fails in
dmi_save_oem_strings while allocating dmi_devices of sizeof(struct
dmi_device) corresponding to these strings.
On x86_64 since we cannot use alloc_bootmem this early, the code uses a
static array of 2048 bytes (DMI_MAX_DATA) for allocating the memory DMI
needs. It does not survive the creation of empty strings and devices.
Fix this by detecting and not newly allocating empty strings and instead
using a one statically defined dmi_empty_string.
Also do not create a new struct dmi_device for each empty string - use
one statically define dmi_device with .name=dmi_empty_string and add
that to the dmi_devices list.
On x64 this should stop the OOM with same current size of DMI_MAX_DATA
and on x86 this should save a good amount of (27*65 bytes +
27*sizeof(struct dmi_device) bootmem.
Compile and boot tested on both 32-bit and 64-bit x86.
Signed-off-by: Parag Warudkar <parag.warudkar@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no need for kobject_unregister() anymore, thanks to Kay's
kobject cleanup changes, so replace all instances of it with
kobject_put().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop using kobject_register, as this way we can control the sending of
the uevent properly, after everything is properly initialized.
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stop using kobject_register, as this way we can control the sending of
the uevent properly, after everything is properly initialized.
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using a kset for this simple directory is an overkill.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no firmware "subsystem" it's just a directory in /sys that
other portions of the kernel want to hook into. So make it a kobject
not a kset to help alivate anyone who tries to do some odd kset-like
things with this.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dynamically create the kset instead of declaring it statically.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dynamically create the kset instead of declaring it statically.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dynamically create the kset instead of declaring it statically.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This cleans up a lot of code and gets rid of a unneeded macro, and gets
us one step closer to deleting the deprecated subsys_attr code.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These files should not be "normal" sysfs files as they really are binary
ones. This patch makes them binary files and saves code in doing so.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Tested-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need a "default" ktype for a kset. We should set this
explicitly every time for each kset. This change is needed so that we
can make ksets dynamic, and cleans up one of the odd, undocumented
assumption that the kset/kobject/ktype model has.
This patch is based on a lot of help from Kay Sievers.
Nasty bug in the block code was found by Dave Young
<hidave.darkstar@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This simply allows other sub-systems (such as ACPI)
to access and print out slots in static dmi_ident[].
Signed-off-by: Len Brown <len.brown@intel.com>
gcc 3.2 has a hard time coping with the code in dmi_id_init():
drivers/built-in.o(.init.text+0x789e): In function `dmi_id_init':
: undefined reference to `__you_cannot_kmalloc_that_much'
make: *** [.tmp_vmlinux1] Error 1
Moving half of the code to a separate function seems to help. This is a
no-op for gcc 4.1 which will successfully inline the code anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Dave Airlie <airlied@linux.ie>
Tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
define global BIT macro
move all local BIT defines to the new globally define macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get rid of input BIT* duplicate defines
use newly global defined macros for input layer. Also remove includes of
input.h from non-input sources only for BIT macro definiton. Define the
macro temporarily in local manner, all those local definitons will be
removed further in this patchset (to not break bisecting).
BIT macro will be globally defined (1<<x)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: <dtor@mail.ru>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: <lenb@kernel.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: <perex@suse.cz>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <vernux@us.ibm.com>
Cc: <malattia@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes it a bit more sane when trying to figure out how to clean up
the ktype mess.
Based on a larger patch from Kay Sievers
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DEFINE_DMI_ATTR macro has a single user left so we can expand it
for slightly shorter/simpler code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can use sysfs attributes with an extra parameter for dmi id
attributes. This makes it possible to use the same callback function
for all attributes, reducing the binary size significantly (-18% on
x86_64.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Three main sets of changes:
1) dmi_get_system_info() return value should have been marked const,
since callers should not be changing that data.
2) const-ify DMI internals, since DMI firmware tables should,
whenever possible, be marked const to ensure we never ever write to
that data area.
3) const-ify DMI API, to enable marking tables const where possible
in low-level drivers.
And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.
The bulk of the changes are #2 and #3, which are interrelated. #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Beacuse SERIAL_PORT_DFNS is removed from include/asm-i386/serial.h and
include/asm-x86_64/serial.h. the serial8250_ports need to be probed late in
serial initializing stage. the console_init=>serial8250_console_init=>
register_console=>serial8250_console_setup will return -ENDEV, and console
ttyS0 can not be enabled at that time. need to wait till uart_add_one_port in
drivers/serial/serial_core.c to call register_console to get console ttyS0.
that is too late.
Make early_uart to use early_param, so uart console can be used earlier. Make
it to be bootconsole with CON_BOOT flag, so can use console handover feature.
and it will switch to corresponding normal serial console automatically.
new command line will be:
console=uart8250,io,0x3f8,9600n8
console=uart8250,mmio,0xff5e0000,115200n8
or
earlycon=uart8250,io,0x3f8,9600n8
earlycon=uart8250,mmio,0xff5e0000,115200n8
it will print in very early stage:
Early serial console at I/O port 0x3f8 (options '9600n8')
console [uart0] enabled
later for console it will print:
console handover: boot [uart0] -> real [ttyS0]
Signed-off-by: <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Well, first of all, I don't want to change so many files either.
What I do:
Adding a new parameter "struct bin_attribute *" in the
.read/.write methods for the sysfs binary attributes.
In fact, only the four lines change in fs/sysfs/bin.c and
include/linux/sysfs.h do the real work.
But I have to update all the files that use binary attributes
to make them compatible with the new .read and .write methods.
I'm not sure if I missed any. :(
Why I do this:
For a sysfs attribute, we can get a pointer pointing to the
struct attribute in the .show/.store method,
while we can't do this for the binary attributes.
I don't know why this is different, but this does make it not
so handy to use the binary attributes as the regular ones.
So I think this patch is reasonable. :)
Who benefits from it:
The patch that exposes ACPI tables in sysfs
requires such an improvement.
All the table binary attributes share the same .read method.
Parameter "struct bin_attribute *" is used to get
the table signature and instance number which are used to
distinguish different ACPI table binary attributes.
Without this parameter, we need to offer different .read methods
for different ACPI table binary attributes.
This is impossible as there are various ACPI tables on different
platforms, and we don't know what they are until they are loaded.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysfs is now completely out of driver/module lifetime game. After
deletion, a sysfs node doesn't access anything outside sysfs proper,
so there's no reason to hold onto the attribute owners. Note that
often the wrong modules were accounted for as owners leading to
accessing removed modules.
This patch kills now unnecessary attribute->owner. Note that with
this change, userland holding a sysfs node does not prevent the
backing module from being unloaded.
For more info regarding lifetime rule cleanup, please read the
following message.
http://article.gmane.org/gmane.linux.kernel/510293
(tweaked by Greg to not delete the field just yet, to make it easier to
merge things properly.)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch below adds DMI/SMBIOS based module autoloading to the Linux
kernel. The idea is to load laptop drivers automatically (and other
drivers which cannot be autoloaded otherwise), based on the DMI system
identification information of the BIOS.
Right now most distros manually try to load all available laptop
drivers on bootup in the hope that at least one of them loads
successfully. This patch does away with all that, and uses udev to
automatically load matching drivers on the right machines.
Basically the patch just exports the DMI information that has been
parsed by the kernel anyway to userspace via a sysfs device
/sys/class/dmi/id and makes sure that proper modalias attributes are
available. Besides adding the "modalias" attribute it also adds
attributes for a few other DMI fields which might be useful for
writing udev rules.
This patch is not an attempt to export the entire DMI/SMBIOS data to
userspace. We already have "dmidecode" which parses the complete DMI
info from userspace. The purpose of this patch is machine model
identification and good udev integration.
To take advantage of DMI based module autoloading, a driver should
export one or more MODULE_ALIAS fields similar to these:
MODULE_ALIAS("dmi:*:svnMICRO-STARINT'LCO.,LTD:pnMS-1013:pvr0131*:cvnMICRO-STARINT'LCO.,LTD:ct10:*");
MODULE_ALIAS("dmi:*:svnMicro-StarInternational:pnMS-1058:pvr0581:rvnMSI:rnMS-1058:*:ct10:*");
MODULE_ALIAS("dmi:*:svnMicro-StarInternational:pnMS-1412:*:rvnMSI:rnMS-1412:*:cvnMICRO-STARINT'LCO.,LTD:ct10:*");
MODULE_ALIAS("dmi:*:svnNOTEBOOK:pnSAM2000:pvr0131*:cvnMICRO-STARINT'LCO.,LTD:ct10:*");
These lines are specific to my msi-laptop.c driver. They are basically
just a concatenation of a few carefully selected DMI fields with all
potentially bad characters stripped.
Besides laptop drivers, modules like "hdaps", the i2c modules
and the hwmon modules are good candidates for "dmi:" MODULE_ALIAS
lines.
Besides merely exporting the DMI data via sysfs the patch adds
support for a few more DMI fields. Especially the CHASSIS fields are
very useful to identify different laptop modules. The patch also adds
working MODULE_ALIAS lines to my msi-laptop.c driver.
I'd like to thank Kay Sievers for helping me to clean up this patch
for posting it on lkml.
Patch is against Linus' current GIT HEAD. Should probably apply to
older kernels as well without modification.
Signed-off-by: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to work on cleaning up the relationship between kobjects, ksets and
ktypes. The removal of 'struct subsystem' is the first step of this,
especially as it is not really needed at all.
Thanks to Kay for fixing the bugs in this patch.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanup kernel-doc notation in drivers/firmware/edd.c.
Add edd.c to DocBook/kernel-api.tmpl.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix race when deleting an EFI variable and issuing another EFI command on
the same variable. The removal of the variable from the efivars_list
should be done in efivar_delete and not delayed until the kobject release.
Furthermore, remove the item from the list at module unload time, and use
list_for_each_entry_safe() rather than list_for_each_safe() for
readability.
Tested on ia64.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
platform_device_register_simple() returns error code as pointer when it
fails. The return value should be checked by IS_ERR().
Cc: Abhay Salunke <abhay_salunke@dell.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a size check in smi_data_write to prevent possible wrapping problems
with large pos values when calling smi_data_buf_realloc on 32-bit.
Signed-off-by: Doug Warzecha <Douglas_Warzecha@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/firmware/dell_rbu.c: In function 'packetize_data':
drivers/firmware/dell_rbu.c:252: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'int'
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The error path path mistakenly called sysfs_create_group() rather than
sysfs_remove_group(). They take the same arguments, so it's easy to
cut-n-paste such a bug.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
dell_rbu: fix pr_debug argument warnings
Use size_t length modifier when outputting size_t and use %p instead of %lu for
'u8 *'.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This teaches dmi_decode() how to decode and save OEM Strings (type 11) DMI
information, which is currently discarded silently. Existing code using
DMI is not affected. Follows the "System Management BIOS (SMBIOS)
Specification" (http://www.dmtf.org/standards/smbios), and also the
userspace dmidecode.c code.
OEM Strings are the only safe way to identify some hardware, e.g., the
ThinkPad embedded controller used by the soon-to-be-submitted tp_smapi
driver. This will also let us eliminate the long whitelist in the mainline
hdaps driver (in a future patch).
Signed-off-by: Shem Multinymous <multinymous@gmail.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add DMI interface functions to a new Firmware Interfaces chapter in the
kernel-api DocBook. Clean up kernel-doc in drivers/firmware/dmi_scan.c.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Lots of people use this. Apparently RH has for over 18 months so lets
drop EXPERIMENTAL.
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dmi_scan.c is arch-independent and is used by i386, x86_64, and ia64.
Currently all three arches compile it from arch/i386, which means that ia64
and x86_64 depend on things in arch/i386 that they wouldn't otherwise care
about.
This is simply "mv arch/i386/kernel/dmi_scan.c drivers/firmware/" (removing
trailing whitespace) and the associated Makefile changes. All three
architectures already set CONFIG_DMI in their top-level Kconfig files.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andrey Panin <pazke@orbita1.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Almost all users of the table addresses from the EFI system table want
physical addresses. So rather than doing the pa->va->pa conversion, just keep
physical addresses in struct efi.
This fixes a DMI bug: the efi structure contained the physical SMBIOS address
on x86 but the virtual address on ia64, so dmi_scan_machine() used ioremap()
on a virtual address on ia64.
This is essentially the same as an earlier patch by Matt Tolentino:
http://marc.theaimsgroup.com/?l=linux-kernel&m=112130292316281&w=2
except that this changes all table addresses, not just ACPI addresses.
Matt's original patch was backed out because it caused MCAs on HP sx1000
systems. That problem is resolved by the ioremap() attribute checking added
for ia64.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: "Tolentino, Matthew E" <matthew.e.tolentino@intel.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Andi Kleen <ak@muc.de>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not use platform_device_register_simple() as it is going away, define
dcdbas_driver and implement ->probe() and ->remove() functions so manual
binding and unbinding will work with this driver.
Also switch to using attribute_group when creating sysfs attributes and
make sure to check and handle errors; explicitely remove attributes when
detaching driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
smi_data_buf_free() references dcdbas_pdev when calling
dma_free_coherent(). In dcdbas_exit(), smi_data_buf_free() is called after
platform_device_unregister(dcdbas_pdev).
This patch moves platform_device_unregister(dcdbas_pdev) after
smi_data_buf_free() in dcdbas_exit().
Signed-off-by: Doug Warzecha <Douglas_Warzecha@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=5854
Root cause:
The dell_rbu driver creates entries in /sys/class/firmware/dell_rbu/ by
calling request_firmware_nowait (without hotplug ) this function inturn
starts a kernel thread which creates the entries in
/sys/class/firmware/dell_rbu/loading , data and the thread waits on the
user action to return control back to the callback fucntion of dell_rbu.
The thread calls wait_on_completion which puts it in a D state until the
user action happens. If there is no user action happening the load average
goes up as the thread D state is taken in to account. Also after
downloading the BIOS image the enrties go away momentarily but they are
recreated from the callback function in dell_rbu. This causes the thread
to get recreated causing the load average to permenently stay around 1.
Fix:
The dell_rbu also creates the entry
/sys/devices/platform/dell_rbu/image_type at driver load time. The image
type by default is mono if required the user can echo packet to image_type
to make the BIOS update mechanism using packets. Also by echoing init in
to image_type the /sys/class/firmware/dell_rbu entries can be created.
The driver code was changed to not create /sys/class/firmware/dell_rbu
entries during load time, and also to not create the above entries from the
callback function. The entries are only created by echoing init to
/sys/devices/platform/dell_rbu/image_type The user now needs to create the
entries to download the image monolithic or packet. This fixes the issue
since the kernel thread only is created when ever the user is ready to
download the BIOS image; this minimizes the life span of the kernel thread
and the load average goes back to normal.
Signed off by Abhay Salunke <abhay_salunke@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Move capable() from sched.h to capability.h;
- Use <linux/capability.h> where capable() is used
(in include/, block/, ipc/, kernel/, a few drivers/,
mm/, security/, & sound/;
many more drivers/ to go)
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This driver only appears on IA32 & EM64T boxes.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch has the changes to support the memory floor fix done in Dell
BIOS. The BIOS incase of packet update mechanism would not accept packet
placed in memory below a cretain address. This address is by default 128K
but can change. The driver now can accept the memory floor if the user
chooses to make it will try to allocate contiguous physical memory above
the memory floor by allocating a set of packets till a valid memory
allocation is made. All the allocates then are freed. This repeats for
everty packet.
This patch was created by Michael E Brown and has been tested on 2.6.14-rc5
Signed-of-by: Michael E Brown <Michael_E_Brown@Dell.com>
Signed-off-by: Abhay Salunke <abhay_salunke@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's nasty to set random drivers to default m because people who just press
enter on make oldconfig get these. Remove the default m
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add CONFIG_X86_32 for i386. This allows selecting options that only apply
to 32-bit systems.
(X86 && !X86_64) becomes X86_32
(X86 || X86_64) becomes X86
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mike Christie