coccinelle check scripts/coccinelle/locks/call_kern.cocci found that
in drivers/usb/host/xhci.c an allocation with GFP_KERNEL is done
with locks held:
xhci_resume
spin_lock_irq(xhci->lock)
xhci_setup_msix
kmalloc(GFP_KERNEL)
Change it to GFP_ATOMIC.
Signed-off-by: David Sterba <dsterba@suse.cz>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit
65fd427 (USB: ehci tdi : let's tdi_reset set host mode)
broke the build using ARM's mx51_defconfig:
CC drivers/usb/host/ehci-hcd.o
In file included from drivers/usb/host/ehci-hcd.c:1166:
drivers/usb/host/ehci-mxc.c: In function 'ehci_mxc_drv_probe':
drivers/usb/host/ehci-mxc.c:192: error: 'ehci' undeclared (first use in this function)
drivers/usb/host/ehci-mxc.c:192: error: (Each undeclared identifier is reported only once
drivers/usb/host/ehci-mxc.c:192: error: for each function it appears in.)
drivers/usb/host/ehci-mxc.c:117: warning: unused variable 'temp'
make[3]: *** [drivers/usb/host/ehci-hcd.o] Error 1
make[2]: *** [drivers/usb/host/ehci-hcd.o] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Fix it together with the warning about the unused variable and use
msleep instead of mdelay as requested by Alan Stern.
Cc: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Nguyen Dinh-R00091 <R00091@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 126512e3f2 added support for FSL's USB
controller on powerpc. In this commit the Open Firmware code was selected
and compiled unconditionally.
This breaks on ARM systems from FSL which use the same driver (.i.e. the i.MX
series), because ARM don't have OF support (yet). This patch fixes the problem
by only selecting the OF code on systems with Open Firmware support.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Compile-Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
VIA and WonderMedia Systems-on-Chip feature a standard EHCI host
controller. This adds necessary glue to use the standard driver
with these systems.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The SH USB interface has both OHCI and EHCI modes that share the
same interrupt. Flag the OHCI IRQ as shared in preparation for EHCI
support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The OCTEON II SOC has USB EHCI and OHCI controllers connected directly
to the internal I/O bus. This patch adds the necessary 'glue' logic
to allow ehci-hcd and ohci-hcd drivers to work on OCTEON II.
The OCTEON normally runs big-endian, and the ehci/ohci internal
registers have host endianness, so we need to select
USB_EHCI_BIG_ENDIAN_MMIO.
The ehci and ohci blocks share a common clocking and PHY
infrastructure. Initialization of the host controller and PHY clocks
is common between the two and is factored out into the
octeon2-common.c file.
Setting of USB_ARCH_HAS_OHCI and USB_ARCH_HAS_EHCI is done in
arch/mips/Kconfig in a following patch.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1675/
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (110 commits)
sh: i2c-sh7760: Replase from ctrl_* to __raw_*
sh: clkfwk: Shuffle around to match the intc split up.
sh: clkfwk: modify for_each_frequency end condition
sh: fix clk_get() error handling
sh: clkfwk: Fix fault in frequency iterator.
sh: clkfwk: Add a helper for rate rounding by divisor ranges.
sh: clkfwk: Abstract rate rounding helper.
sh: clkfwk: support clock remapping.
sh: pci: Convert to upper/lower_32_bits() helpers.
sh: mach-sdk7786: Add support for the FPGA SRAM.
sh: Provide a generic SRAM pool for tiny memories.
sh: pci: Support secondary FPGA-driven PCIe clocks on SDK7786.
sh: pci: Support slot 4 routing on SDK7786.
sh: Fix up PMB locking.
sh: mach-sdk7786: Add support for fpga gpios.
sh: use pr_fmt for clock framework, too.
sh: remove name and id from struct clk
sh: free-without-alloc fix for sh_mobile_lcdcfb
sh: perf: Set up perf_max_events.
sh: perf: Support SH-X3 hardware counters.
...
Fix up trivial conflicts (perf_max_events got removed) in arch/sh/kernel/perf_event.c
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
Fix this error when CONFIG_PM is not enabled:
drivers/usb/host/xhci.c:675: error: implicit declaration of function 'usb_root_hub_lost_power'
Wrap xhci_suspend() and xhci_resume() into an ifdef CONFIG_PM, along with
the functions that only they call -- xhci_save_registers() and
xhci_restore_registers().
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements the PCI suspend/resume.
Please refer to xHCI spec for doing the suspend/resume operation.
For S3, CSS/SRS in USBCMD is used to save/restore the internal state.
However, an error maybe occurs while restoring the internal state.
In this case, it means that HC internal state is wrong and HC will be
re-initialized.
Signed-off-by: Libin Yang <libin.yang@amd.com>
Signed-off-by: Dong Nguyen <dong.nguyen@amd.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements xHCI bus suspend/resume function hook.
In the patch it goes through all the ports and suspend/resume
the ports if needed.
If any port is in remote wakeup, abort bus suspend as what ehci/ohci do.
Signed-off-by: Libin Yang <libin.yang@amd.com>
Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit implements port remote wakeup.
When a port is in U3 state and resume signaling is detected from a device,
the port transitions to the Resume state, and the xHC generates a Port Status
Change Event.
For USB3 port, software write a '0' to the PLS field to complete the resume
signaling. For USB2 port, the resume should be signaling for at least 20ms,
irq handler set a timer for port remote wakeup, and then finishes process in
hub_control GetPortStatus.
Some codes are borrowed from EHCI code.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add software trigger USB device suspend resume function hook.
Do port suspend & resume in terms of xHCI spec.
Port Suspend:
Stop all endpoints via Stop Endpoint Command with Suspend (SP) flag set.
Place individual ports into suspend mode by writing '3' for Port Link State
(PLS) field into PORTSC register. This can only be done when the port is in
Enabled state. When writing, the Port Link State Write Strobe (LWS) bit shall
be set to '1'.
Allocate an xhci_command and stash it in xhci_virt_device to wait completion for
the last Stop Endpoint Command. Use the Suspend bit in TRB to indicate the Stop
Endpoint Command is for port suspend. Based on Sarah's suggestion.
Port Resume:
Write '0' in PLS field, device will transition to running state.
Ring an endpoints' doorbell to restart it.
Ref: USB device remote wake need another patch to implement. For details of
how USB subsystem do power management, please see:
Documentation/usb/power-management.txt
Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Libin Yang <libin.yang@amd.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xHCI driver uses hardware assigned device address. This may cause device
address conflict in certain cases.
Use kernel assigned address for devices under xHCI. Store the xHC assigned
address locally in xHCI driver.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Rename xhci_reset_device() to xhci_discover_or_reset_device().
If xhci_discover_or_reset_device() is called to reset a device which does
not exist or does not match the udev, it calls xhci_alloc_dev() to
re-allocate the device.
This would prevent the reset device failure, possibly due to the xHC restore
error during S3/S4 resume.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a pointer to udev in struct xhci_virt_device. When allocate a new
virt_device, make the pointer point to the corresponding udev.
Modify xhci_check_args(), check if virt_dev->udev matches the target udev,
to make sure command is issued to the right device.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some functions changed by 1c98347e61.
However, There was a change mistake of the function (outsw).
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Paul Mundt <lethal@linux-sh.org>
Cc: stable <stable@kernel.org> [.35 & .36]
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For all modules, change <module>-objs to <module>-y; remove
if-statements and replace with lists using the kbuild idiom; move
flags to the top of the file; and fix alignment while trying to
maintain the original scheme in each file.
None of the dependencies are modified.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hardware can only do DMA to 4 byte aligned addresses.
When this requirement is not met use PIO or a bounce buffer.
PIO is used when the buffer is small enough to directly
use the hardware data memory (2*maxpacket).
A bounce buffer is used for larger transfers.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Release the hardware resources and reset the internal HCD state
associated with an isochronous endpoint when the last URB queued
for it completes.
Previously this was only done in then endpoint_disable() method
causing usbtest 15 and 16 to hang when run twice in succession
without a disconnect.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We already have fields describing the hardware data memory
(dmem_size and dmem_offset) in the HCD private data,
use them rather than the rather obscure read from the
hardware descriptor.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove a local variable left over from some debugging code.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds native scatter-gather support to uhci-hcd.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Extends FSL EHCI platform driver glue layer to support
MPC5121 USB controllers. MPC5121 Rev 2.0 silicon EHCI
registers are in big endian format. The appropriate flags
are set using the information in the platform data structure.
MPC83xx system interface registers are not available on
MPC512x, so the access to these registers is isolated in
MPC512x case. Furthermore the USB controller clocks
must be enabled before 512x register accesses which is
done by providing platform specific init callback.
The MPC512x internal USB PHY doesn't provide supply voltage.
For boards using different power switches allow specifying
DRVVBUS and PWR_FAULT signal polarity of the MPC5121 internal
PHY using "fsl,invert-drvvbus" and "fsl,invert-pwr-fault"
properties in the device tree USB nodes. Adds documentation
for this new device tree bindings.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace FSL USB platform code by simple platform driver for
creation of FSL USB platform devices.
The driver creates platform devices based on the information
from USB nodes in the flat device tree. This is the replacement
for old arch fsl_soc usb code removed by this patch. The driver
uses usual of-style binding, available EHCI-HCD and UDC
drivers can be bound to the created devices. The new of-style
driver additionaly instantiates USB OTG platform device, as the
appropriate USB OTG driver will be added soon.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The un-registration of OHCI driver was not done in the ohci_hcd_mod_exit
function. This was affecting rmmod command not to work for OMAP3
platforms. The platform driver un-registration for OMAP3 platforms is
perfomed while removing the OHCI module from kernel.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In today linux-next I got a compile error on usb/host/isp1362-hcd:
drivers/usb/host/isp1362-hcd.c: In function ‘isp1362_hub_control’:
drivers/usb/host/isp1362-hcd.c:1680: error: ‘ohci’ undeclared (first use in this function)
The problem is when the CONFIG_USB_OTG option is enabled.
ohci variable is never declared and there isn't any CONFIG_USB_OTG dependent code
besides the portion defined in isp1362_hub_control.
So I think that maybe USB OTG support is not needed/supported.
This patch removes the CONFIG_USB_OTG dependent block so the driver can compile cleanly.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1417) fixes a problem affecting some (or all) nVidia
chipsets. When the computer is shut down, the OHCI controllers
continue to power the USB buses and evidently they drive a Reset
signal out all their ports. This prevents attached devices from going
to low power. Mouse LEDs stay on, for example, which is disconcerting
for users and a drain on laptop batteries.
The fix involves leaving each OHCI controller in the OPERATIONAL state
during system shutdown rather than putting it in the RESET state.
Although this nominally means the controller is running, in fact it's
not doing very much since all the schedules are all disabled. However
there is ongoing DMA to the Host Controller Communications Area, so
the patch also disables the bus-master capability of all PCI USB
controllers after the shutdown routine runs.
The fix is applied only to nVidia-based PCI OHCI controllers, so it
shouldn't cause problems on systems using other hardware. As an added
safety measure, in case the kernel encounters one of these running
controllers during boot, the patch changes quirk_usb_handoff_ohci()
(which runs early on during PCI discovery) to reset the controller
before anything bad can happen.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tdi_reset is already taking care of setting host mode for tdi devices.
Don't duplicate code in platform driver.
Make ehci_halt a nop if the controller is not in host mode (otherwise it
will fail), and let's ehci_reset do the tdi_reset.
We need to move hcd->has_tt flags before ehci_halt, in order ehci_halt
knows we are a tdi device.
Before the setup routine was doing :
- put controller in host mode
- ehci_halt
- ehci_init
- hcd->has_tt = 1;
- ehci_reset
Now we do :
- hcd->has_tt = 1;
- ehci_halt
- ehci_init
- ehci_reset
PS : now we handle correctly the device -> host transition.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
U2D Controller of pxa3xx is able to work in host mode.
Make pxa specific ohci implementation aware of it.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
We have to do so due to HW limitation.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The _remove() routine is flagged __init_or_module, despite only being
used in a __devexit context. As the rest of the driver is already
balanced out with __devinit, switch to __devexit and __devexit_p()
wrapping.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The iounmap(ehci->ohci_hcctrl_reg); should be the first thing we do
because the ioremap() was the last thing we did. Also if we hit any of
the goto statements in the original code then it would have led to a
NULL dereference of "ehci". This bug was introduced in: 796bcae736
"USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]"
I modified the few lines in front a little so that my code didn't
obscure the return success code path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a isoc transfer bug reported by Sander Eikelenboom.
When ep->skip is set, endpoint ring dequeue pointer should be updated
when processed every missed td. Although ring dequeue pointer will also
be updated when ep->skip is clear, leave it intact during missed tds
processing may cause two issues:
1). If the very next valid transfer following missed tds is a short
transfer, its actual_length will be miscalculated;
2). If there are too many missed tds during transfer, new inserted tds
may found the transfer ring full and urb enqueue fails.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code to increment the TRB pointer has a slight ambiguity that could
lead to a bug on different compilers. The ANSI C specification does not
specify the precedence of the assignment operator over the postfix
operator. gcc 4.4 produced the correct code (increment the pointer and
assign the value), but a MIPS compiler that one of John's clients used
assigned the old (unincremented) value.
Remove the unnecessary assignment to make all compilers produce the
correct assembly.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ISP1760 has some timing requirements where it has to delay a short
period after a write to a register has started. However, this delay is
from the time the write hits the USB chip (the ISP1760), not from the
time where the processor started processing the write. So on a quick
enough processor, it is sometimes possible for the write to not hit the
device before we start delaying, and we then violate the part's timing
requirements, so things stop working.
To avoid all this, insert a write barrier after the register write and
before the timing delay/register read so we can guarantee we only start
counting time after the write has hit the device.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: I2C bus multiplexer driver pca954x
i2c: Multiplexed I2C bus core support
i2c: Use a separate mutex for userspace client lists
i2c: Make i2c_default_probe self-sufficient
i2c: Drop dummy variable
i2c: Move adapter locking helpers to i2c-core
V4L/DVB: Use custom I2C probing function mechanism
i2c: Add support for custom probe function
i2c-dev: Use memdup_user
i2c-dev: Remove unnecessary kmalloc casts
The probe method used by i2c_new_probed_device() may not be suitable
for all cases. Let the caller provide its own, optional probe
function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fake "address-of" expressions that evaluate to NULL generally confuse
readers and can provoke compiler warnings. This patch (as1412)
removes three such fake expressions, using "#ifdef"s in their place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tell the USB core that we can do DMA directly (instead of needing it to
memory-map the buffers for PIO). If the xHCI host supports 64-bit addresses,
set the DMA mask accordingly. Otherwise indicate the host can handle 32-bit DMA
addresses.
This improves performance because the USB core doesn't have to spend time
remapping buffers in high memory into the 32-bit address range.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To tell the host controller that there are transfers on the endpoint
rings, we need to ring the endpoint doorbell. This is a PCI MMIO write,
which can be delayed until another register read is queued.
The previous code would flush the doorbell write by reading the doorbell
register after the write. This may take time, and it's not necessary to
force the host controller to know about the transfers right away. Don't
flush the doorbell register writes.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The interrupter register set includes a register that says whether interrupts
are pending for each event ring (the IP bit). Each MSI-X vector will get its
own interrupter set with separate IP bits. The status register includes an
"Event Interrupt (EINT)" bit that is set when an IP bit is set in any of the
interrupters.
When PCI interrupts are used, the EINT bit exactly mirrors the IP bit in the
single interrupter set, and it is a waste of time to check both registers when
trying to figure out if the xHC interrupted or another device on the shared IRQ
line interrupted. Only check the IP bit to reduce register reads.
The IP bit is automatically cleared by the xHC when MSI or MSI-X is enabled. It
doesn't make sense to read that register to check for shared interrupts (since
MSI and MSI-X aren't shared). It also doesn't make sense to write to that
register to clear the IP bit, since it is cleared by the hardware.
We can tell whether MSI or MSI-X is enabled by looking at the irq number in
hcd->irq. If it's -1, we know MSI or MSI-X is enabled.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the event handler functions no longer use xhci_set_hc_event_deq()
to update the event ring dequeue pointer, that function is not used by
anything in xhci-ring.c. Move that function into xhci-mem.c and make it
static.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI specification suggests that writing the hardware event ring dequeue
pointer register too often can be an expensive operation for the xHCI hardware
to manage. It suggests minimizing the number of writes to that register.
Originally, the driver wrote the event ring dequeue pointer after each
event was processed. Depending on how the event ring moderation register
is set up and how fast the transfers are completing, there may be several
events processed for each interrupt. This patch makes the hardware event
ring dequeue pointer be written only once per interrupt.
Make the transfer event handler and port status event handler only write
the software event ring dequeue pointer. Move the updating of the
hardware event ring dequeue pointer into the interrupt function. Move the
contents of xhci_set_hc_event_deq() into the interrupt handler. The
interrupt handler must clear the event handler busy flag, so it might as
well also write the dequeue pointer to the same register. This eliminates
two 32-bit PCI reads and two 32-bit PCI writes.
Reported-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xhci_handle_event() is now only called from within xhci-ring.c, so make it
static.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove a duplicate register read of the interrupt pending register from
xhci_irq(). Also, remove waiting on the posted write of that register.
The host will see it eventually. It will probably read the register
itself before deciding whether to interrupt the system again, forcing the
posted write to complete.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we move xhci_work() into xhci_irq(), we don't need to read the operational
register status field twice.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most of the work for interrupt handling is done in xhci-ring.c, so it makes
sense to move the functions that are first called when an interrupt happens
(xhci_irq() or xhci_msi_irq()) into xhci-ring.c, so that the compiler can better
optimize them.
Shorten some lines to make it pass checkpatch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've been using perf to measure the top symbols while transferring 1GB of data
on a USB 3.0 drive with dd. This is using the raw disk with /dev/sdb, with a
block size of 1K.
During performance testing, the top symbol was xhci_triad_to_transfer_ring(), a
function that should return immediately if streams are not enabled for an
endpoint. It turned out that the functions to find the endpoint ring was
defined in xhci-mem.c and used in xhci-ring.c and xhci-hcd.c. I moved a copy of
xhci_triad_to_transfer_ring() and xhci_urb_to_transfer_ring() into xhci-ring.c
and declared them static. I also made a static version of
xhci_urb_to_transfer_ring() in xhci.c.
This improved throughput on a 1GB read of the raw disk with dd from
186MB/s to 195MB/s, and perf reported sampling the xhci_triad_to_transfer_ring()
0.06% of the time, rather than 9.26% of the time.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch below on gregkh tree only creates 'lpm' file under
ehci->debug_dir, but not removes it when unloading module,
USB: EHCI: EHCI 1.1 addendum: preparation
which can make loading of ehci-hcd module failed after unloading it.
This patch replaces debugfs_remove with debugfs_remove_recursive
to remove ehci debugfs dir and files. It does fix the bug above,
and may simplify the removing procedure.
Also, remove the debug_registers, debug_async and debug_periodic
field from ehci_hcd struct since they are useless now.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds USB 2.0 support to ssb ohci driver.
This patch was used in OpenWRT for a long time now.
CC: Steve Brown <sbrown@cortland.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
imx21_hc_reset() uses schedule_timeout() without setting state to
STATE_(UN)INTERRUPTIBLE. As it is called in cycle without checking of
pending signals, use schedule_timeout_uninterruptible().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Isochronous endpoint needs a bigger size of transfer ring. Isochronous URB
consists of multiple packets, each packet needs a isoc td to carry, and
there will be multiple trbs inserted to the ring at one time. One segment
is too small for isochronous endpoints, and it will result in
room_on_ring() check failure and the URB is failed to enqueue.
Allocate bigger ring for isochronous endpoint. 8 segments should be enough.
This will be replaced with dynamic ring expansion in the future.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements isochronous urb enqueue and interrupt handler part.
When an isochronous urb is passed to xHCI driver, first check the transfer
ring to guarantee there is enough room for the whole urb. Then update the
start_frame and interval field of the urb. Always assume URB_ISO_ASAP
is set, and never use urb->start_frame as input.
The number of isoc TDs is equal to urb->number_of_packets. One isoc TD is
consumed every Interval. Each isoc TD consists of an Isoch TRB chained to
zero or more Normal TRBs.
Call prepare_transfer for each TD to do initialization; then calculate the
number of TRBs needed for each TD. If the data required by an isoc TD is
physically contiguous (not crosses a page boundary), then only one isoc TRB
is needed; otherwise one or more additional normal TRB shall be chained to
the isoc TRB by the host.
Set TRB_IOC to the last TRB of each isoc TD. Do not ring endpoint doorbell
to start xHC procession until all the TDs are inserted to the endpoint
transer ring.
In irq handler, update urb status and actual_length, increase
urb_priv->td_cnt. When all the TDs are completed(td_cnt is equal to
urb_priv->length), giveback the urb to usbcore.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add urb_priv data structure to xHCI driver. This structure allows multiple
xhci TDs to be linked to one urb, which is essential for isochronous
transfer. For non-isochronous urb, only one TD is needed for one urb;
for isochronous urb, the TD number for the urb is equal to
urb->number_of_packets.
The length field of urb_priv indicates the number of TDs in the urb.
The td_cnt field indicates the number of TDs already processed by xHC.
When td_cnt matches length, the urb can be given back to usbcore.
When an urb is dequeued or cancelled, add all the unprocessed TDs to the
endpoint's cancelled_td_list. When process a cancelled TD, increase
td_cnt field. When td_cnt equals urb_priv->length, giveback the
cancelled urb.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds mechanism to process Missed Service Error Event.
Sometimes the xHC is unable to process the isoc TDs in time, it will
generate Missed Service Error Event. In this case some TDs on the ring are
not processed and missed. When encounter a Missed Servce Error Event, set
the skip flag of the ep, and process the missed TDs until reach the next
processed TD, then clear the skip flag.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds new cases to trb_comp_code switch, and moves
the switch judgment ahead of fetching td.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the bulk and interrupt td processing part in
handle_tx_event() into a separate function process_bulk_intr_td().
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the ctrl td processing part in handle_tx_event()
into a separate function process_ctrl_td().
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the td universal processing part in handle_tx_event()
into a separate function finish_td().
if finish_td() returns 1, it indicates the urb can be given back.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1409) removes some dead code from the ehci-hcd
scheduler. Thanks to the previous patch in this series, stream->depth
is no longer used. And stream->start and stream->rescheduled
apparently have not been used for quite a while, except in some
statistics-reporting code that never gets invoked.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1408) rearranges the scheduling code in ehci-hcd, partly
to improve its structure, but mainly to change the way it works.
Whether or not a transfer exceeds the hardware schedule length will
now be determined by looking at the last frame the transfer would use,
instead of the first available frame following the end of the transfer.
The benefit of this change is that it allows the driver to accept
valid URBs which would otherwise be rejected. For example, suppose
the schedule length is 1024 frames, the endpoint period is 256 frames,
and a four-packet URB is submitted. The four transfers would occupy
slots that are 0, 256, 512, and 768 frames past the current frame
(plus an extra slop factor). These don't exceed the 1024-frame limit,
so the URB should be accepted. But the current code notices that the
next available slot would be 1024 frames (plus slop) in the future,
which is beyond the limit, and so the URB is rejected unnecessarily.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1407) fixes a bug in ehci-hcd's isochronous scheduler.
All its calculations should be done in terms of microframes, but for
full-speed devices, sched->span is stored in frames. It needs to be
converted.
This fix is liable to expose problems in other drivers. The old code
would accept URBs that should not have been accepted, so drivers have
had no reason to avoid submitting URBs that exceeded the maximum
schedule length. In an attempt to partially compensate for this, the
patch also adjusts the schedule length from a minimum of 256 frames up
to a minimum of 512 frames.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1406) adds a micro-optimization to ehci-hcd's scheduling
code. Instead of computing remainders with respect to the schedule
length, use bitwise-and (which is quicker). We know that the schedule
length will always be a power of two, but the compiler doesn't have
this information.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1405) fixes a small bug in ehci-hcd's isochronous
scheduler. Not all EHCI controllers are PCI, and the code shouldn't
assume that they are. Instead, introduce a special flag for
controllers which need to delay iso scheduling for full-speed devices
beyond the scheduling threshold.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: David Brownell <david-b@pacbell.net>
CC: stable <stable@kernel.org>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Enable MSI/MSI-X supporting in xhci driver.
Provide the mechanism to fall back using MSI and Legacy IRQs
if MSI-X IRQs register failed.
Signed-off-by: Dong Nguyen <Dong.Nguyen@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>,
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CONFIG_ARCH_KARO doesn't exist in Kconfig and is never defined anywhere
else, therefore removing all references for it from the source code.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently devices don't get detected automatically if the ehci
module is inserted 2nd time onward. We need to disconnect and
reconnect the device for it to get detected and enumerated.
Resetting the USB PHY using PHY reset comamnd over ULPI fixes
this issue. Tested on OMAP3EVM.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we use the HCD_LOCAL_MEM flag and dma_declare_coherent_memory() to
enforce the host controller's local memory utilization we also need to
disable native scatter-gather support, otherwise hcd_alloc_coherent() in
map_urb_for_dma() is called with urb->transfer_buffer == NULL, that
triggers a NULL pointer dereference.
We can also consider to add a WARN_ON() and return an error code to
better catch this problem in the future.
At the moment no driver seems to hit this bug, so I should
consider this a low-priority fix.
Signed-off-by: Andrea Righi <arighi@develer.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1396) adds code to uhci-hcd to support the
vendor-specific wakeup settings found in Intel's ICHx hardware. A
couple of unnecessary memory barriers are removed. And the root hub
isn't put back into the "suspended" state if power was lost during a
system sleep -- there's not much point in doing so because the root hub
will be resumed shortly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1394) adds code to ehci-hcd, ohci-hcd, and uhci-hcd for
automatically resuming the root hub when the controller is resumed, if
the root hub has a wakeup request pending on some port.
During resume from system sleep this doesn't matter, because the root
hubs will naturally be resumed along with every other device in the
system. However it _will_ matter for runtime PM: If the controller is
suspended and a remote wakeup request is received then the controller
will autoresume, but we need to ensure that the root hub also
autoresumes. Otherwise the wakeup request would be ignored, the
controller would go back to sleep, and the cycle would repeat a large
number of times (I saw this happen before the patch was written).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1385) adds a "do_wakeup" parameter to the pci_suspend
method used by PCI-based host controller drivers. ehci-hcd in
particular needs to know whether or not to enable wakeup when
suspending a controller. Although that information is currently
available through device_may_wakeup(), when support is added for
runtime suspend this will no longer be true.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefan Weil