CHANNEL_G has to be set for 2GHZ channels since
IS_CHAN_G() checks for this in channelFlags and not in
chanmode. To make things messier, ath9k_hw_process_ini()
checks for CHANNEL_G in chanmode and not in channelFlags.
The supreme, brain-searing fix is to set the
flag in both cases.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BAR frames have to be sent to mac80211 only if the
current channel is HT. Also, move the macro to
enum ath9k_rx_filter.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k ahb requests an IRQ and indicates 'ath9k' claimed it,
ath9k pci requests an IRQ and indicates 'ath' claims it;
since 'ath' is another module sync both ahb and pci to claim
the irq using 'ath9k'.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've cleaned up ath_init_device() and its children enough
to pass meaninful errors back from probe. When this fails
it means our device could not be initialized and a meaninful
error will have been passed.
Do the same for request_irq() and also synchronize the error
messages while at it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The -ENOMEM was never being passed on failure.
While at it use dev_err() as ahb does upon failure.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As generic hw timer interrupt handler is moved to tasklet,
we no more need to call spin_lock_irqsave().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point handling this in hard irq, move it to
tasklet.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Doing an RTC reset when DMA is active may corrupt memory,
make sure no DMA is active at this moment by doing an
AHB reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds 3-wire bluetooth coex support for AR9285.
This support can be enabled through btcoex_enable modparam.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need a hw cap bit for btcoex anymore as btcoex scheme type
is enough to do this.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also define macros for wlanactive and btactive (5 & 6) gpios.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure btcoex register configured with appropriate values
after it is initialized with the default values from initvals.h
during reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function currently does initialization + enable the
btcoex support. Split it into two logical functions which
does the above operations separately. Btcoex initialization
is done during attach time and enabling this feature is done
in start(). Also, add code to disable btcoex support in stop().
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When dumping register contents, HW has to be awake.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PA Calibration is not needed for high power solutions.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* First PA driver (PDPADRV1) was not powered down properly.
* Compensation capacitor for dynamic PA was programmed incorrectly.
Also, remove a stray REG_READ.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PA calibration need not be done if the offset is not varying.
The current logic does PA calibration even if the offset is the
same.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent a read of powInfo[-1] in the first iteration.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX/RX chainmasks were set to 1x1 during scanning.
Configure them properly with the values retrieved from
the EEPROM.
Also, this requires scan_start/scan_end callbacks to be
locked with sc->mutex.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for FIF_OTHER_BSS was missing. This patch adds support for this
filtering mode which in turn resolves a problem where mesh interfaces would not
receive broadcast traffic.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Other than ns_avgbrssi (Average beacon rssi) no data of
ath9k_node_stats is being used anywhere. Nuke this structure
and move its only useful member to ar5416Anistate. Also cleanup
this redundant data in ath_softc.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the beacon rssi that LPF gives is divided and rounded
up by ATH_RSSI_EP_MULTIPLIER twice. This will leave the incorrect rssi
in ANI. Having correct rssi in ANI fixes the connection stability at
< 30dB rssi range. This patch removes the unncessary computation of average
rssi over already valid average rssi. Also removes the redundant macros to
find average rssi.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the shared regulatory structure into the
common structure. We will use this ongoing for common
data.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ath9k_stop(), tx_complete_work was being cancelled twice.
This patch fixes it. Also, locking sc->mutex should be done
at the beginning.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable AsyncFIFO and AGGWEP for AR9287_12 and later revisions only.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ath9k_stop() where the HW
was not put into FULL_SLEEP state. Not doing so will
cause issues in suspend-resume and the HW will not respond
to chip resets.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug where the device was enabled
before restoring the PCI state.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diversity_control and antenna_switch_swap are already
present in ath9k_ops_config. Remove duplicate occurrences
in ath_hw.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PHY counters are available in all chipsets supported
by ath9k. Remove the check.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports the AR9002 family of chipsets. This includes
the AR9285 and the miniPCI AR9223 and AR9220 (which themselves
have AR9280+AR5133).
We now refer people to the wiki page as it seems this is not
as popular as we would have hoped.
Reported-by: JD <jd1008@gmail.com>
Cc: Dakota Lee <Dakota.Lee@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turns out ath5k and ath9k can share the same helper to
allocates RX skbs. We allocate skbs aligned to the cache line
size. This requirement seems to have come from AR5210; when
this was not done it seems sometimes we'd get bogus data. I'm
also told it may have been a performance enhancement
consideration. In the end I can't be sure we can remove this
on new hardware so just keep this and start sharing it through
ath.ko.
Make ath9k start using this, ath5k is next.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the the patch:
ath9k: use new FIF_PSPOLL configure filter
I forgot to add the new FIF_PSPOLL to the supported mask.
Without this we mask out the FIF_PSPOLL flag therefore
we'd ignore it from mac80211.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI uses the beacon RSSI for its operation.
Update this properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chainmask can be obtained directly from ath_hw.
Also, use a helper macro for comparing CTLs - this improves readability.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Write CCK power-per-rate array always and report
correct TX power to regulatory.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch revamps the antenna configuration mechanism
for 4K chips.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A subsequent patch would use these for configuring
antennae on AR9285.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
regChainOffset is always zero, remove it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add eeprom_def.c, eeprom_4k.c and eeprom_9287.c
This improves maintainability.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We used to set pspoll filter on ath9k on AP mode but
we no longer need this mode specific check as mac80211
now does the check for us and informs us when we should
enable pspoll through FIF_PSPOLL.
Cc: Igor Perminov <igor.perminov@inbox.ru>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/ath/ath9k/eeprom.o
drivers/net/wireless/ath/ath9k/eeprom.c: In function ‘ath9k_hw_AR9287_check_eeprom’:
drivers/net/wireless/ath/ath9k/eeprom.c:2866: warning: comparison of distinct pointer types lacks a cast
Cc: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will finalize this after some driver core changes, for now
we leave this unsupported.
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used later to add support for ar9271.
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't use typdefs on ath9k, remove that _t.
Cc: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_keyreset() has a spurious check for ah->curchan..
remove it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The keycache reset will not fail as right above we ensure
to set the sc->keymax to be <= ah->caps.keycache_size. Just remove
this dangling check.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If hw initialization fails (ath9k_hw_init()) on ath_init_softc()
we bail out and call ath9k_hw_detach(). The call ath9k_hw_detach()
is conditional though as ath9k_hw_init() could itself have called
ath9k_hw_detach(). Just describing this is itself a brain twister.
Avoid this nonsense by removing ath9k_hw_detach() from ath9k_hw_init().
Upon hw initialization failure we expect the callers to take care of
the cleanup.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kfree(NULL) works so remove all those branches which check
for it before kfree()'ing on ath9k_hw_rfdetach().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We re-label the device driver initialization routines from the
ath_softc, the "Software Carrier" fillers. This should make it
clearer what each of these do.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During initialization ath9k tends to use "attach" to when we
initialize hardware due to the fact we used to attach a "HAL".
The notion of a HAL is long gone, so lets just be clear on what
we are doing.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes reading the hardware initialization process
easier to understand. The new helpers added are:
ath9k_hw_init_cal_settings()
ath9k_hw_init_mode_regs()
ath9k_hw_init_mode_gain_regs()
ath9k_hw_init_11a_eeprom_fix()
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're now propagating the -ENOMEM error so there is no need to
keep a debug message there now.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reflects better what we are actually doing there.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reflects better what we are actually doing there.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The softc is cached and set within the ath_hw struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_attach() was going first through some device id verifier,
and then calling some other helper which was doing the real hardware
initialization. Lets just do the devid checks within the real worker
by calling a helper ath9k_hw_devid_supported().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this in case attach and friends try to get back to
ah from the softc somehow.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets us trim one argument off of hw initializer routines.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets us simplify attach code and arguments passed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were never propagating hw initialization errors, lets
do that now and also use -EOPNOTSUPP when device revision is
not supported yet.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes adding new hw revisions a one line change here.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will clean this up next to just use a switch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.
We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:
* ieee80211_queue_work()
* ieee80211_queue_delayed_work()
These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.
Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Monotonicity of packet error rate should be kept when moving
from one phy to another (legacy to ht, ht single stream to dual,
etc). Current code skips updating per for other phys.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the lowest rate in 11na ht40 mode is 13.5Mbps this shortens the
range when compared to 11na ht20 mode where the lowest rate is 6.5Mbps.
To improve the range, make 6.5Mbps as the lowest rate in 11na ht40 mode,
this improves the range by approximately 2dB. 11ng ht40 does not have
this issue as it also has basic rates (1, 2, 5.5 and 11).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make atheros wireless drivers visible when you select
"Atheros wirless drivers". Adds links to ath.ko page,
and Atheros drivers page on the wiki.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should be cancelling our work at the stop callback since
we are borrowing the mac80211 workqueue for our work. As it
stands mac80211 expects this for suspend purposes.
The ath9k specific virtual wiphy stuff need only be
cancelled only when the we have no secondary virtual wiphys.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this as we'll be moving the cancel elsewhere later.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k uses the mac80211 workqueue for 4 different types of work:
* Led blink work
* TX hang monitoring work
* internal wiphy schedular work
* channel change work done for internal wiphy schedular
Since the internal wiphy schedular can end up kicking off some
channel channel change work we should first cancel the wiphy
schedular work and then the channel change work.
The TX hang work can be cancelled second since we're going down
anyway.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our version goes by the kernel release.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are using setpower routines regardless of the current power mode.
Don't bother the hardware, if it is not necessary.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a small window where the mac80211 changes the IEEE80211_CONF_PS
flag, and then informs the driver about the change. We have a race
condition if we are checking the flag in the same time. Avoid it by
introducing a local variable, and using that instead of checking the
IEEE80211_CONF_PS flag directly.
This fix the problem reported by Luis:
http://article.gmane.org/gmane.linux.kernel.wireless.general/34363
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup aggregation start/stop function interfaces.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect limits leads to reads outside array bounds.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 will have disabled the queues for us when
needed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have a dedicated function for this kind of checks, use that
instead of duplicating the code.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we are in NETWORK SLEEP state, AR_SLP32_TSF_WRITE_STATUS limit
always exceeds in 'ath9k_hw_reset_tsf', because reading of the
AR_SLP3 register always return with the magic 0xdeadbeef value.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This uses the new configuration changes indicated up by
mac80211 when all interfaces are marked idle. We need to do
a little more work as we have our own set of virtual
wiphys within ath9k.
Only when all virtual wiphys are inactive do we allow an idle
state change for a wiphy to trigger disabling the radio.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These functions are changing the power mode of the chip, but this may
have unpredictable effects, if another code are trying to set the power
mode via 'ath9k_hw_setpower' in the same time from another context.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Uninline these functions before we add functional changes to them.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because ath9k_setpower is called from various contexts, we have to
protect it against concurrent calls.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update tx BA window and complete the frame as failed
one if we can't clone the holding descriptor due to
unavailability of descriptors.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
oops, this one should be part of the original patch
"ath9k: downgrade assert in ath_clone_txbuf()"
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware doesn't generate interrupts in some cases and so work
around this by monitoring the TX status periodically and reset the
chip if required.
This behavior of the hardware not generating the TX interrupts can
be noticed through ath9k debugfs interrupt statistics when heavy
traffic is being sent from STA to AP. One can easily see this behavior
when the STA is transmitting at a higher rates. The interrupt statistics
in the debugfs interface clearly shows that only RX interrupts alone
being generated and TX being stuck.
TX should be monitored through a timer and reset the chip only when
frames are queued to the hardware but TX interrupts are not generated
for the same even after one second. Also, we shouldn't remove holding
descriptor from AC queue if it happens to be the only descriptor and
schedule TX aggregation regarless of queue depth as it improves
scheduling of AMPDUs from software to hardware queue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Running iperf along with p2p traffic on both TX and RX side then
stop one side, then stop the other side, then start it up again,
eventually the STA gets into a mode that it can not pass data at
all.
A hardware workaround for invalid RSSI can make FIFO write pointer
to jump over read pointer, causing RX data corruption and repeated
DMA. Both TX and RX works fine when the workaround is disabled.
To replace the original hardware work around, software looks for
frames with post delimiter CRC error and mark the RSSI invalid so
that the upperlayer will not use the RSSI associated with this
frame. So disable the hardware workaround by updating the appropriate
registers.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RSSI reported by the RX descriptor requires little manipulation.
Manipulate and report the correct RSSI to the stack. This will
fix the improper signal levels reported by iwconfig iw dev wlanX
station dump. Also the Link Quality reported seems to be varying
(falls to zero also sometimes) when iperf is run from STA to AP.
Also use the default noise floor for now as the one reported
during the caliberation seems to be wrong.
The Signal and Link Quality before this patch (taken while TX is
in progress from STA to AP)
09:59:13.285428037 Link Quality=29/70 Signal level=-81 dBm
09:59:13.410660084 Link Quality=20/70 Signal level=-90 dBm
09:59:13.586864392 Link Quality=21/70 Signal level=-89 dBm
09:59:13.710296281 Link Quality=21/70 Signal level=-89 dBm
09:59:13.821683064 Link Quality=25/70 Signal level=-85 dBm
09:59:13.933402989 Link Quality=24/70 Signal level=-86 dBm
09:59:14.045839276 Link Quality=26/70 Signal level=-84 dBm
09:59:14.193926673 Link Quality=23/70 Signal level=-87 dBm
09:59:14.306230262 Link Quality=31/70 Signal level=-79 dBm
09:59:14.419459667 Link Quality=26/70 Signal level=-84 dBm
09:59:14.530711167 Link Quality=37/70 Signal level=-73 dBm
09:59:14.642593962 Link Quality=29/70 Signal level=-81 dBm
09:59:14.754361169 Link Quality=21/70 Signal level=-89 dBm
09:59:14.866217355 Link Quality=21/70 Signal level=-89 dBm
09:59:14.976963623 Link Quality=28/70 Signal level=-82 dBm
09:59:15.089149809 Link Quality=26/70 Signal level=-84 dBm
09:59:15.205039887 Link Quality=27/70 Signal level=-83 dBm
09:59:15.316368003 Link Quality=23/70 Signal level=-87 dBm
09:59:15.427684036 Link Quality=36/70 Signal level=-74 dBm
09:59:15.539756380 Link Quality=21/70 Signal level=-89 dBm
09:59:15.650549093 Link Quality=22/70 Signal level=-88 dBm
09:59:15.761171672 Link Quality=32/70 Signal level=-78 dBm
09:59:15.872793750 Link Quality=23/70 Signal level=-87 dBm
09:59:15.984421694 Link Quality=22/70 Signal level=-88 dBm
09:59:16.097315093 Link Quality=21/70 Signal level=-89 dBm
The link quality and signal level after this patch (take while
TX is in progress from STA to AP)
17:21:25.627848091 Link Quality=65/70 Signal level=-45 dBm
17:21:25.762805607 Link Quality=65/70 Signal level=-45 dBm
17:21:25.875521888 Link Quality=66/70 Signal level=-44 dBm
17:21:25.987468448 Link Quality=66/70 Signal level=-44 dBm
17:21:26.100628151 Link Quality=66/70 Signal level=-44 dBm
17:21:26.213129671 Link Quality=66/70 Signal level=-44 dBm
17:21:26.324923070 Link Quality=65/70 Signal level=-45 dBm
17:21:26.436831357 Link Quality=65/70 Signal level=-45 dBm
17:21:26.610356973 Link Quality=65/70 Signal level=-45 dBm
17:21:26.723340047 Link Quality=65/70 Signal level=-45 dBm
17:21:26.835715293 Link Quality=64/70 Signal level=-46 dBm
17:21:26.949542748 Link Quality=64/70 Signal level=-46 dBm
17:21:27.062261613 Link Quality=65/70 Signal level=-45 dBm
17:21:27.174511563 Link Quality=64/70 Signal level=-46 dBm
17:21:27.287616232 Link Quality=64/70 Signal level=-46 dBm
17:21:27.400598119 Link Quality=64/70 Signal level=-46 dBm
17:21:27.511381404 Link Quality=64/70 Signal level=-46 dBm
17:21:27.624530421 Link Quality=65/70 Signal level=-45 dBm
17:21:27.737807109 Link Quality=64/70 Signal level=-46 dBm
17:21:27.850861352 Link Quality=65/70 Signal level=-45 dBm
17:21:27.963369436 Link Quality=64/70 Signal level=-46 dBm
17:21:28.076582289 Link Quality=64/70 Signal level=-46 dBm
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move its only member (u8 per) to struct ath_rate_priv.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of rssi reduce interval.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k rate control is based on only PER (packet error rate),
remove unused code which was intented to do rssi based rate
selection.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the cleanup we just use get_rate as a wrapper, skip
the wrapper.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All current rate control algorithms agree to send management and no-ack
frames at the lowest rate. They also agree to do this when sta
and the private rate control data is NULL. We add a hlper to mac80211
for this and simplify the rate control algorithm code.
Developers wishing to make enhancements to rate control algorithms
are for broadcast/multicast can opt to not use this in their
gate_rate() mac80211 callback.
Cc: Zhu Yi <yi.zhu@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: ipw3945-devel@lists.sourceforge.net
Cc: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We check for this condition early on in our mac80211 get_rate()
callback ath_get_rate(), so remove this check later down the path.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The purpose is to find the highest rate we can use.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a lot of gaps here.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This saves us 2733 bytes.
text data bss dec hex filename
252265 3628 1584 257477 3edc5 ath9k-has-b-rate.ko
249905 3628 1584 255117 3e48d ath9k.ko
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Siged-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
What this does is get us our next lower rate so call it that,
ath_rc_get_lower_rix().
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is just calling another helper, so just use the other
helper directly. This should make it clear that when do not
find the next rate we stick to the current one.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used, remove this.
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used, and when we need to get the lowest rate
we should simply use mac80211's own rate_lowest_index(sband, sta).
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no functional change and just cleans up the code
to be more legible and removes a useless variable for
Multi Rate Retry.
For regular frames we use 2 retries for MRR segments [0-2].
For the last MRR segment [3] we use 4.
MRR[0] = 2
MRR[1] = 2
MRR[2] = 2
MRR[3] = 4
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The case where no vaid rate is found should not happen now
but to help debugging and downgrade this to a warn.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AP mode we must tune ANI specially for 2 GHz and
for 5 GHz. We mask in only the flags we want to toggle
on ath9k_hw_ani_control() through the ah->ani_function
bitmask, this will take care of ignoring changes during
ANI reset which we were disabling before.
Testedy-by: Steven Luo <steven@steven676.net>
Cc: Bennyam Malavazi <bennyam.malavazi@atheros.com>
Cc: Jouni Malinen <jouni.malinen@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't allow users to open debugfs files, because it can cause oopses.
When a user opens some file, driver unlinks it and frees the
corresponding structure, we will dereference freed memory.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue when the TX and RX streams are different.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI calibration shouldn't be done when we are not on our home channel.
This is already verified. However, it is racy. Fix this by proper
spin locks.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI is not required when the STA is disconnected. So stop it and enable
ANI for adhoc and monitor mode.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unncessary STATION mode check in ath9k_bss_assoc_info() as
it is called only for STATION mode.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were not differentiating quality between legacy and HT
configurations. We change this to consider the differences.
New theory for reporting quality:
At a hardware RSSI of 45 you will be able to use MCS 7 reliably.
At a hardware RSSI of 45 you will be able to use MCS 15 reliably.
At a hardware RSSI of 35 you should be able use 54 Mbps reliably.
MCS 7 is the highets MCS index usable by a 1-stream device.
MCS 15 is the highest MCS index usable by a 2-stream device.
All ath9k devices are either 1-stream or 2-stream.
How many bars you see is derived from the qual reporting.
A more elaborate scheme can be used here but it requires tables
of SNR/throughput for each possible mode used. For the MCS table
you can refer to the wireless wiki:
http://wireless.kernel.org/en/developers/Documentation/ieee80211/802.11n
This should fix this bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=13537
Cc: Janath.Peiris@atheros.com
Cc: Matt.Smith@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helper only clears the SC_OP_WAIT_FOR_{BEACON,CAB} flags.
Remove it and clear these flags directly in the approptiate
places instead.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All SC_OP_WAIT_* flags will be cleared in 'ath9k_conf' when PS mode
is disabled, so we don't have to clear it here.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan