Implement deep-sleep on MPC52xx.
SDRAM is put into self-refresh with help of SRAM code
(alternatives would be code in FLASH, I-cache).
Interrupt code must also not be in SDRAM, so put it
in I-cache.
MPC52xx core is static, so contents will remain intact even
with clocks turned off.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add fsl-i2c to mpc5200 i2c node in device tree, and enable FSL_SOC.
Tested to work with built-in eeprom on lite5200b.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the global cpu speed variable according to current cpufreq speed,
/proc/cpuinfo reports the actual speed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows "hotplugging" of CPUs on G5 machines. CPUs that are
disabled are put into an idle loop with the decrementer frequency set
to minimum. To wake them up again we kick them just like when bringing
them up. To stop those CPUs from messing with any global state we stop
them from entering the timer interrupt.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Only publish of_platform devices if running on a machine that has them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixups for the ps3 interrupt routines to support all HV device
in a generic way.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A minor change to remove a duplicate variable assignement in ps3_mm_shutdown();
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PS3 support for the PowerPC processor's Data Address Breakpoint Register
(DABR).
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In commit 0fba3a1f39 (a very long time ago,
May 2006), I fixed a bug that caused powermacs to crash when you tried
entering standby/mem suspend states.
As I'm now getting more familiar with the suspend code I notice a few
more things:
1. we previously misunderstood what pm_ops is for, it isn't supposed to be
for doing platform dependent suspend/resume stuff that needs to be done
for suspend to disk (as we currently try to use it!), it is instead for
entering platform dependent suspend states ("standby", "mem").
2. due to the first point, we never properly save FPU and altivec states
when suspending to disk. It probably hasn't hurt yet because the process
that writes the "disk" to /sys/power/state uses neither and its context
is used.
This patch addresses these points as follows:
1. remove all pm_ops from powermac, powermac suspend to ram isn't currently
usable via /sys/power/state but is done via the PMU instead.
2. move the code responsible for storing FPU/altivec state into
save_processor_state and the set_context() call to restore_processor_state.
3. add a call to kernel_enable_spe()
It may look like there is some code removal missing but that is
actually because the new suspend.h file overrides the ppc/suspend.h
one which was previously used.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since we don't have it active by default, the STRICT_MM_TYPECHECKS
option has bitrotted again. This patch fixes a couple of simple build
fixes if the option is selected. First, pud_t mustn't be defined in
page.h on 32-bit systems, because it conflicts with the version in the
generic pud-folding code. Second, pci_32.c is missing a __pgprot()
wrapper call. Third, a couple of PS3 files use constants of type
pgprot_t when they need the raw values, we add pgprot_val() calls to
fix this.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add 'mdio' to bus scan id list for platforms with QE UEC
as a consequence of converting UEC mdio driver to an
of_platform driver in the ucc_geth phylib conversion patch.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some versions of pSeries firmware fail to set up a
dma-window property for PCI slots that are unoccupied.
As a result, the loop searching for this propery, in
pci_dma_dev_setup_pSeriesLP(), can run to the end, resulting
in a NULL pointer dereference later in the routine. This
patch prevents the crash, and prints a warning message.
This is theoretically a rare error, as it occurs on what
is hopefully just beta levels of firmware. But just in case
this firmware escapes into the wild, this patch will avoid
the crash.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
The original code here is wrong, it applies "previous" knowledge.
The way the cpufreq core is designed is that the policy for the
secondary CPU that comes online says that it must in fact not
use this policy but use the same as the other CPUs that are
listed, which in fact is CPU#0.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove loops_per_jiffy early initialization code for 7448HPC2 platforms.
Since udelay no longer uses loops_per_jiffy it is not necessary to
initialize it early.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Call of_find_node_by_type with NULL instead of np
so the cpu node does not get put twice.
This was causing kref_put warnings.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use DEFINE_SPINLOCK instead of initializing spinlocks to
SPIN_LOCK_UNLOCKED, since DEFINE_SPINLOCK is better for lockdep.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Just another pass through arch/powerpc for old usages.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Shuffle Kconfig order, making the platform drivers menu depend on the global
option instead of each driver being dependent on it.
Also fix dependency of PPC_PMAC on the G5 one.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 9414715a7b,
at Olaf Hering's request:
> Paul, please discard this patch. The optional graphics card may have
> also device_type 'serial' if it is in VGA mode.
> I will send an updated patch later.
check_legacy_ioport makes only sense on PREP, CHRP and pSeries.
They may have an isa node with PS/2, parport, floppy and serial ports.
Remove the check_legacy_ioport call from ppc_md, it's not needed
anymore. Hardware capabilities come from the device-tree.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cpufreq driver for PA Semi PWRficient processors.
Signed-off-by: Egor Martovetsky <egor@pasemi.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/pasemi/gpio_mdio.c really depends on CONFIG_PHYLIB.
Add a config option for it, allow for it to be disabled if needed and fix
the dependency.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/pasemi/setup.c: In function 'pasemi_publish_devices':
arch/powerpc/platforms/pasemi/setup.c:220: warning: implicit declaration of function 'of_platform_bus_probe'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace uses with of_find_node_by_name and for_each_node_by_name.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is an old interface and is replaced by of_find_compatible_node.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename MPIC_BROKEN_U3 to something a little more descriptive. Its
effect is to enable support for HT irqs behind the PCI-X/HT bridge on
U3/U4 (aka. CPC9x5) parts.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that we always take a device tree in arch/powerpc, there's no good
reason not to allow a single kernel to support multiple embedded 4xx
boards - the correct platform code can be selected based on the device
tree information.
Therefore, this patch re-arranges the 4xx Kconfig code to allow this.
In addition we:
- use "select" instead of depends to configure the correct
config options for specific 4xx CPUs and workarounds, which
makes the information about specific boards and CPUs less
scattered.
- Some old, unused (in arch/powerpc) config options are
removed: WANT_EARLY_SERIAL, IBM_OCP, etc.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MDIO driver for PHY's connected via GPIO as on the PA Semi Electra
eval board.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reset MPIC on boot to clear some timer state that firmware might
leave configured.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device 0 function 0 on the root bus is really a two-function bus agent,
but only the first function is visible. Because of this, we need to
allow config accesses into the second range. Modify the check for valid
offsets accordingly.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable Periodic Recalibration (PTCAL) support for Cell XDR memory,
using the new ibm,cbe-start-ptcal and ibm,cbe-stop-ptcal RTAS calls.
Tested on QS20 and QS21 (by Thomas Huth). It seems that SLOF has
problems disabling, at least on QS20; this patch should only be
used once these problems have been addressed.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds support for a proper device-tree.
A porper device-tree on cell contains be nodes
for each CBE containg nodes for SPEs and all the
other special devices on it.
Ofcourse oldschool devicetree is still supported.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The new PMI driver was added in order to support
cpufreq on blades that require the frequency to
be controlled by the service processor, so use it
on those.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds some attributes the cpu and spu nodes:
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_begin
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_end
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_full_stop
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch introduces a little function for transforming
register values into temperature.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds code to deal with conversion of
logical cpu to cbe nodes. It removes code that
assummed there were two logical CPUs per CBE.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This change fixes the case where spu_base and spufs are initialised on a
system with no SPEs - unconditionally create the spu_lists so spu_alloc
doesn't explode, and check for spu_management ops before starting spufs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
arch/powerpc/platforms/cell/spu_base.c | 7 ++++---
arch/powerpc/platforms/cell/spufs/inode.c | 5 +++++
2 files changed, 9 insertions(+), 3 deletions(-)
spu_base.c is always built into the kernel image, so there is no need
for a cleanup function. And some of the things it does are in the
way for my following patches, so I'd rather get rid of it ASAP.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
- remove the spu_acquire_runnable from spu_run_init. I need to
opencode it in spufs_run_spu in the next patch
- remove various inline attributes, we don't really want to inline
long functions with multiple callsites
- cleanup return values and runcntl_write calls in spu_run_init
- use normal kernel codingstyle in spu_reacquire_runnable
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
spu_coredump_calls.owner is NULL in case of a builtin spufs,
so the checks in here break.
Check for the availability of the spu_coredump_calls variable
instead.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Dynamically allocated read/write buffer in spufs_arch_write_note() will
not be freed. Convert it to get_free_page at the same time.
Cc: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Change the loop in spu_wait to be a little more straightforward.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Domen Puncer