for cyclic dma, dont makr the descriptor as complte. Fix the remaining users of
cyclic dma which do so
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Mika Westerberg <mika.westerberg@iki.fi>
Shawn Guo <shawn.guo@linaro.org> writes:
I chose to base it on Sascha's imx-common-clk series than -rc, because
otherwise it will keep patching clock file that has been removed by
imx-common-clk series. It also depends on imx-pinctrl pull-request
I just sent to be functional.
Note: when imx-common-clk and imx-pinctrl get merged together, the
following files will have conflicts. But the conflicts should not be
so hard to resolve.
[arnd: resolved those merge conflicts by pulling pinctrl branch]
* imx/dt: (24 commits)
ARM: dts: imx53-qsb: enable audio support
ARM: dts: imx51-babbage: enable audio support
ARM: imx: add audio codec clk lookup for imx53-qsb
ARM: imx: add audmux pad setting for imx51-babbage
ARM: imx: add more imx5 ssi clocks
ARM: dts: imx53-qsb: Add Dialog DA9053 PMIC support
ARM: dts: imx6q-sabrelite: add serial2 pinctrl support
ARM: dts: imx6q-sabrelite: add sound device imx6q-sabrelite-sgtl5000
ARM: imx6q_sabrelite: clk_register_clkdev cko1 for sgtl5000
ARM: imx6q: add ssi1_ipg clk_lookup
ARM: dts: imx6q-sabrelite: add audmux pinctrl support
ARM: dts: imx6q-sabrelite: add i2c1 pinctrl support
ARM: dts: imx6q-sabrelite: add audmux device
ARM: dts: imx6q-sabrelite: add ssi device
ARM: dts: imx6q-arm2: add pinctrl state for usdhc
ARM: imx6: Add UART2 for low-level debug
ARM: imx6q: register phy fixup only when CONFIG_PHYLIB is enabled
ARM: imx6q: move imx6q_sabrelite specific code to a dedicated function
ARM: dts: imx6q-sabrelite: Add SPI NOR support
ARM: dts: Add basic support for imx6q-sabresd
...
Pulls in imx/pinctrl and imx/clock as dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Branch has one driver feature and one board bug fix. Merging it as a driver branch.
DMA driver change was later:
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
* tag 'ep93xx-fixes-for-3.5' of git://github.com/RyanMallon/linux-ep93xx:
dmaengine/ep93xx_dma: Implement double buffering for M2M DMA channels
arm: ep93xx: Don't try to release not acquired GPIO lines
Rewrite mxs_dma_is_apbh and mxs_dma_is_apbx in order to support
other SoCs like imx6q and reform the platform_device_id for the
better further dt support.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Huang Shijie <b32955@freescale.com>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
This can get rid of the mach-dependency.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Huang Shijie <b32955@freescale.com>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Shawn Guo <shawn.guo@linaro.org> writes:
mxs common clk porting for v3.5. It depends on the following two branches.
[1] git://git.linaro.org/people/mturquette/linux.git clk-next
[2] http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-arm.git clkdev
As the mxs device tree conversion will constantly touch clock files,
to save the conflicts, the updated mxs/dt branch coming later will
based on this pull-request.
* 'clk/mxs' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: remove now unused timer_clk argument from mxs_timer_init
ARM: mxs: remove old clock support
ARM: mxs: switch to common clk framework
ARM: mxs: change the lookup name for fec phy clock
ARM: mxs: request clock for timer
clk: mxs: add clock support for imx28
clk: mxs: add clock support for imx23
clk: mxs: add mxs specific clocks
Includes an update to Linux 3.4-rc6
Conflicts:
drivers/clk/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
device_prep_dma_cyclic may be call in audio trigger function which is
atomic context, so we make it atomic too.
- change channel0 lock to spinlock.
- Use polling to wait for channel0 finish running.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
sg->length may or may not contain the length of the dma region to transfer,
depending on the architecture - dma_sg_len(sg) always will though. For the
architectures which use the drivers modified by this patch it probably is the
case that sg->length contains the dma transfer length. But to be consistent and
future proof change them to use dma_sg_len.
To quote Russel King:
sg->length is meaningless to something performing DMA.
In cases where sg_dma_len(sg) and sg->length are the same storage, then
there's no problem. But scatterlists _can_ (and one some architectures) do
split them - especially when you have an IOMMU which can allow you to
combine a scatterlist into fewer entries.
So, anything using sg->length for the size of a scatterlist's DMA transfer
_after_ a call to dma_map_sg() is almost certainly buggy.
The patch has been generated using the following coccinelle patch:
<smpl>
@@
struct scatterlist *sg;
expression X;
@@
-sg[X].length
+sg_dma_len(&sg[X])
@@
struct scatterlist *sg;
@@
-sg->length
+sg_dma_len(sg)
</smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
dmaengine drivers should always use sg_dma_address instead of sg_phys to get the
addresses for the transfer from a sg element.
To quote Russel King:
sg_phys(sg) of course has nothing to do with DMA addresses. It's the
physical address _to the CPU_ of the memory associated with the scatterlist
entry. That may, or may not have the same value for the DMA engine,
particularly if IOMMUs are involved.
And if these drivers are used on ARM, they must be fixed, sooner rather
than later. There's patches in the works which will mean we will end up
with IOMMU support in the DMA mapping later, which means everything I've
said above will become reality.
The patch has been generated using the following coccinelle patch:
<smpl>
@@
struct scatterlist *sg;
@@
-sg_phys(sg)
+sg_dma_address(sg)
</smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
the cookie updates completed the cyclic dma descriptor wrongly. This caused the
BUG_ON to be hit as submit is called for completed descriptor
Fix this by not marking the cyclic descriptor as complete
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
The current code keeps the callbacks invoked from interrupt context, this
does not conform to the Documentation/dmaengine.txt.
So add tasklet support to fix this issue.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
SPEAr platforms now support DT and so must convert all drivers to support DT.
This patch adds DT probing support for Synopsys DMA controller and updates its
documentation too.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Some orion platforms can gate the XOR driver clock. If the clock
exisits, unable/disable it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Nomadik PL080 variant has some extra protection bits that
may be set, so we need to check these bits to see if the
channels are actually available for the DMAengine to use.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alim Akhtar <alim.akhtar@gmail.com>
Cc: Alessandro Rubini <rubini@gnudd.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
When a client calls pl08x_control with DMA_TERMINATE_ALL, it is correct
to terminate and release the phy channel currently in use (if one is in use),
but the phychan_hold counter must also be reset (otherwise it could get
trapped in an unbalanced state).
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Move a couple of tests and do a minor refactor to avoid:
drivers/dma/pl330.c: In function 'pl330_probe':
drivers/dma/pl330.c:2929:215: warning: comparison of distinct pointer types lacks a cast [enabled by default]
drivers/dma/pl330.c: In function 'pl330_tasklet':
drivers/dma/pl330.c:2250:8: warning: 'pch' may be used uninitialized in this function [-Wuninitialized]
drivers/dma/pl330.c:2228:25: note: 'pch' was declared here
drivers/dma/pl330.c:2277:130: warning: 'pch' may be used uninitialized in this function [-Wuninitialized]
drivers/dma/pl330.c:2260:25: note: 'pch' was declared here
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
For some reason I can't figure out we're reading the PL080_INT_STATUS
register instead of PL080_TC_STATUS when checking for the terminal
count. The PL080_INT_STATUS is a logical OR between the error and
terminal count status register and may not report what we want it
to, especially if there is an error and a terminal count at the same
time and the former is not lowered in time for the check in the TC
register. Make sure we read what we're actually interested in.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Alim Akhtar <alim.akhtar@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
A small fallout from Vinod's conversions to dma_transfer_direction,
this small comparison was done with a dma_data_direction instead.
Fix it by comparing against the correct enum.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The patch "ARM: amba: Remove AMBA level regulator support" breaks
the DMA40 driver since the <linux/amba/bus.h> header implicitly
included the regulator consumer header. So include it explicitly
and fix the build error.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
can be directly stopped by issuing a SUSPEND_REQ on the EE
bits. There is no need to suspend the physical channel and
restart it.
Also, the support for pre-V2 hw is discontinued.
EE bits for writing:
00: disable only if AS=11 or AS=00
01: enable
10: suspend_req only if AS=01 & EE=01 or EE=11
11: round / no change for writing
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This loop on EBCISR register was designed to clear IRQ sources before enabling
a DMA channel. This register is clear-on-read so a race condition can appear if
another channel is already active and has just finished its transfer.
Removing this read on EBCISR is fixing the issue as there is no case where an IRQ
could be pending: we already make sure that this register is drained at probe()
time and during resume.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Enable channel in device_issue_pending call, so that the order between
cookie assignment and channel enabling can be ensured naturally.
It fixes the mxs gpmi-nand breakage which is caused by the incorrect
order of cookie assigning and channel enabling.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Huang Shijie <b32955@freescale.com>
Tested-by <samgandhi9@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
the cookie updates completed the cyclic dma descriptor wrongly. This caused the
BUG_ON to be hit as submit is called for completed descriptor
Fix this by not marking the cyclic descriptor as complete
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add double buffering support for M2M DMA channels. Implement this by using EP93xx
M2M DMA Buffer and Control Finite State Machines to be sure that we are not
disabling the channel when it's actually operating.
Signed-off-by: Rafal Prylowski <prylowski@metasoft.pl>
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Remove SoC dependency and make it generic for every Atmel ARM AT91. That will
allow to select this driver for newer chips. Keep dependency on AT91 because of
the use of an header file located in include/mach directory.
Modify the comment to reflect this.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F3IR
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine fixes from Dan Williams:
1/ regression fix for Xen as it now trips over a broken assumption
about the dma address size on 32-bit builds
2/ new quirk for netdma to ignore dma channels that cannot meet
netdma alignment requirements
3/ fixes for two long standing issues in ioatdma (ring size overflow)
and iop-adma (potential stack corruption)
* tag 'dmaengine-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
netdma: adding alignment check for NETDMA ops
ioatdma: DMA copy alignment needed to address IOAT DMA silicon errata
ioat: ring size variables need to be 32bit to avoid overflow
iop-adma: Corrected array overflow in RAID6 Xscale(R) test.
ioat: fix size of 'completion' for Xen
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
This is the fallout from adding memcpy alignment workaround for certain
IOATDMA hardware. NetDMA will only use DMA engine that can handle byte align
ops.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Silicon errata where when RAID and legacy descriptors are mixed, the legacy
(memcpy and friends) operation must have alignment of 64 bytes to avoid
hanging. This effects Intel Xeon C55xx, C35xx, E5-2600.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The alloc order can be up to 16 and 1 << 16 will over flow the 16bit
integer. Change the appropriate variables to 16bit to avoid overflow.
Reported-by: Jim Harris <james.r.harris@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull ARM fixes from Russell King:
"Nothing too big here, just small fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: fix more fallout from 9f97da78bf (Disintegrate asm/system.h for ARM)
ARM: fix bios32.c build warning
ARM: 7337/1: ptrace: fix ptrace_read_user for !CONFIG_MMU platforms
ARM: fix missing bug.h include in arch/arm/kernel/insn.c
ARM: sa11x0: fix build errors from DMA engine API updates
Artem's cleanup of the MTD API continues apace.
Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others.
More work on DiskOnChip G3, new driver for DiskOnChip G4.
Clean up debug/warning printks in JFFS2 to use pr_<level>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk92K6UACgkQdwG7hYl686NrMACfWQJRWasR78MWKfkT2vWZwTFJ
X5AAoKiSYO2pfo5gWJGOAahNC1zUqMX0
=i3Vb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
The recent merge of the sa11x0 code into mainline had silent conflicts
with further development of the DMA engine API, leading to build errors
and warnings:
drivers/net/irda/sa1100_ir.c: In function 'sa1100_irda_dma_start':
drivers/net/irda/sa1100_ir.c:151: error: too few arguments to function 'chan->device->device_prep_slave_sg'
drivers/dma/sa11x0-dma.c: In function 'sa11x0_dma_probe':
drivers/dma/sa11x0-dma.c:950: warning: assignment from incompatible pointer type
Fix these.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
Bug: cppcheck reported overflow in array assignment (for loop walks
0 to IOP_ADMA_NUM_SRC_TEST+2, array size is IOP_ADMA_NUM_SRC_TEST).
Reported as: https://bugzilla.kernel.org/show_bug.cgi?id=42677
Test code pq_src array was grown by two elements to correspond with actual
usage (IOP_ADMA_NUM_SRC_TEST+2), stack consumption was kept constant by
modifying the pq_dest two element array which is only used when pq_src
is referenced up to IOP_ADMA_NUM_SRC_TEST elements into the address
of the new last two elements of the pq_src array. This is presumed to
be the original intent but would be reliant on compilers always having
pq_dest contiguous with the final element of pq_src.
Note: This is a re-send of a request for review from two weeks ago.
Looking for review (or shootdown), adding LKML to list for a wider
audience. Thanks.
Updated per review comments of Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Don Morris <don.morris@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
commit 6bd081277e "dmaengine: imx-dma: merge old dma-v1.c with
imx-dma.c" removed the dependency in config for the imx dma driver,
whereas it should depend on ARCH_MXS
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
[1] Background :
The GPMI does ECC read page operation with a DMA chain consist of three DMA
Command Structures. The middle one of the chain is used to enable the BCH,
and read out the NAND page.
The WAIT4END(wait for command end) is a comunication signal between
the GPMI and MXS-DMA.
[2] The current DMA code sets the WAIT4END bit at the last one, such as:
+-----+ +-----+ +-----+
| cmd | ------------> | cmd | ------------------> | cmd |
+-----+ +-----+ +-----+
^
|
|
set WAIT4END here
This chain works fine in the mx23/mx28.
[3] But in the new GPMI version (used in MX50/MX60), the WAIT4END bit should
be set not only at the last DMA Command Structure,
but also at the middle one, such as:
+-----+ +-----+ +-----+
| cmd | ------------> | cmd | ------------------> | cmd |
+-----+ +-----+ +-----+
^ ^
| |
| |
set WAIT4END here too set WAIT4END here
If we do not set WAIT4END, the BCH maybe stalls in "ECC reading page" state.
In the next ECC write page operation, a DMA-timeout occurs.
This has been catched in the MX6Q board.
[4] In order to fix the bug, rewrite the last parameter of mxs_dma_prep_slave_sg(),
and use the dma_ctrl_flags:
---------------------------------------------------------
DMA_PREP_INTERRUPT : append a new DMA Command Structrue.
DMA_CTRL_ACK : set the WAIT4END bit for this DMA Command Structure.
---------------------------------------------------------
[5] changes to the relative drivers:
<1> For mxs-mmc driver, just use the new flags, do not change any logic.
<2> For gpmi-nand driver, and use the new flags to set the DMA
chain, especially for ecc read page.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move the header to a more common place.
The mxs dma engine is not only used in mx23/mx28, but also used
in mx50/mx6q. It will also be used in the future chips.
Rename it to mxs-dma.h, and create a new folder include/linux/fsl/ to
store the Freescale's header files.
change mxs-dma driver, mxs-mmc driver, gpmi-nand driver, mxs-saif driver
to the new header file.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When merging DMA cookie changes a small chunk
of code was dropped. This broke imx-dma driver.
This patch adds this chunk again and fixes the problem.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
i.MX2 and i.MX1 chips have the possibility to do
interleaved transfers with two constraints:
- Only one chunk can be used (i.e. only 2D transfers are allowed).
- Only 2 interleaved configurations can be applied at the same time
for all channels.
Since this patch adds a new resource 'slots_2d' which is shared
by all the DMA channels and to avoid disgustin locking BUGs, the
'lock' member has been moved to the global 'imxdma_engine' structure.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
There were some 'pr_crit' and 'pr_debug' messages due to the
initial merge. Replace them by 'dev_dbg' and 'dev_warn' to be
consistent.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
These global variables are integrated into the dmaengine structure.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Since this function is always used with 'desc' as first argument
and 'desc->sg' as second argument, the latter is clearly redundant
and can be removed.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This structure was created to allow an smoothless
merge but was meant to be removed. Remaining members
'hw_chaining' and 'watchdog' are moved to the channel
structure.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Use per-descriptor 'len' field to keep track of the remaining bytes
instead. This goes on the direction of eventually removing the
'internal' structure.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
It makes no sense keeping an 'in_use' flag when the multiple descriptor
mechanism already prevents a new DMA transfer to be issued when another
one is in course.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This member is redundant, because it is already present in
descriptor structure. Removing it will make further removing
of 'internal' structure easier.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Removing this function allows moving 'ccr_to_device' and
'ccr_from_device' from internal struct to channel struct.
This repesents a step forward towards removing auxiliary
'internal' structure.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This function is only used once in the driver and uses some
intermediary variables that are not needed anymore. For this
reason it's been merged with 'imxdma_control'.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This function is only used once in the driver and has a lot of checks
that are not needed anymore. For this reason it's been merged
with 'imxdma_enable_hw'.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
dmaengine now provides 'enum dma_transfer_direction' to properly
specify DMA transfer direction. For this reason, DMA_MODE_* defines
are replaced by this new type and therefore dma_mode member becomes
redundant.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Internal structure is just an auxiliary structure used for the initial
merge which is meant to be gone. As data member is not use anywhere
we can simply remove it.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
It is mainly a simple merge changing the prefix of some
functions to fit the imx-dma namings.
As there are no users of the old dma-v1.c api we can safely
remove this file.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
"[PATCH 0/3] RFC - module.h usage cleanups in fs/ and lib/"
https://lkml.org/lkml/2012/2/29/589
--
Fix up files in fs/ and lib/ dirs to only use module.h if they really
need it.
These are trivial in scope vs. the work done previously. We now have
things where any few remaining cleanups can be farmed out to arch or
subsystem maintainers, and I have done so when possible. What is
remaining here represents the bits that don't clearly lie within a
single arch/subsystem boundary, like the fs dir and the lib dir.
Some duplicate includes arising from overlapping fixes from
independent subsystem maintainer submissions are also quashed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Z4w0
-----END PGP SIGNATURE-----
Merge tag 'module-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull cleanup of fs/ and lib/ users of module.h from Paul Gortmaker:
"Fix up files in fs/ and lib/ dirs to only use module.h if they really
need it.
These are trivial in scope vs the work done previously. We now have
things where any few remaining cleanups can be farmed out to arch or
subsystem maintainers, and I have done so when possible. What is
remaining here represents the bits that don't clearly lie within a
single arch/subsystem boundary, like the fs dir and the lib dir.
Some duplicate includes arising from overlapping fixes from
independent subsystem maintainer submissions are also quashed."
Fix up trivial conflicts due to clashes with other include file cleanups
(including some due to the previous bug.h cleanup pull).
* tag 'module-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
lib: reduce the use of module.h wherever possible
fs: reduce the use of module.h wherever possible
includecheck: delete any duplicate instances of module.h
Pull #2 ARM updates from Russell King:
"Further ARM AMBA primecell updates which aren't included directly in
the previous commit. I wanted to keep these separate as they're
touching stuff outside arch/arm/."
* 'amba' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7362/1: AMBA: Add module_amba_driver() helper macro for amba_driver
ARM: 7335/1: mach-u300: do away with MMC config files
ARM: 7280/1: mmc: mmci: Cache MMCICLOCK and MMCIPOWER register
ARM: 7309/1: realview: fix unconnected interrupts on EB11MP
ARM: 7230/1: mmc: mmci: Fix PIO read for small SDIO packets
ARM: 7227/1: mmc: mmci: Prepare for SDIO before setting up DMA job
ARM: 7223/1: mmc: mmci: Fixup use of runtime PM and use autosuspend
ARM: 7221/1: mmc: mmci: Change from using legacy suspend
ARM: 7219/1: mmc: mmci: Change vdd_handler to a generic ios_handler
ARM: 7218/1: mmc: mmci: Provide option to configure bus signal direction
ARM: 7217/1: mmc: mmci: Put power register deviations in variant data
ARM: 7216/1: mmc: mmci: Do not release spinlock in request_end
ARM: 7215/1: mmc: mmci: Increase max_segs from 16 to 128
Starting with v3.2 Jonathan reports that Xen crashes loading the ioatdma
driver. A debug run shows:
ioatdma 0000:00:16.4: desc[0]: (0x300cc7000->0x300cc7040) cookie: 0 flags: 0x2 ctl: 0x29 (op: 0 int_en: 1 compl: 1)
...
ioatdma 0000:00:16.4: ioat_get_current_completion: phys_complete: 0xcc7000
...which shows that in this environment GFP_KERNEL memory may be backed
by a 64-bit dma address. This breaks the driver's assumption that an
unsigned long should be able to contain the physical address for
descriptor memory. Switch to dma_addr_t which beyond being the right
size, is the true type for the data i.e. an io-virtual address
inidicating the engine's last processed descriptor.
[stable: 3.2+]
Cc: <stable@vger.kernel.org>
Reported-by: Jonathan Nieder <jrnieder@gmail.com>
Reported-by: William Dauchy <wdauchy@gmail.com>
Tested-by: William Dauchy <wdauchy@gmail.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch introduces DMA_SLAVE_CONFIG to at_hdmac Atmel DMA driver.
It is needed to fix a regression in the use of atmel-mci.c driver on Atmel
AT91 platforms brouth by e2b35f3:
"dmaengine/dw_dmac: Fix dw_dmac user drivers to adapt to slave_config changes"
We remove some parts of the private structure "at_dma_slave" and use the
information provided by "struct dma_slave_config": source/destination
peripheral registers and access width.
AT_DMA_SLAVE_WIDTH_* values used previously are not needed anymore as we
now use the standard ones. Although some conversion functions are needed to
match register expected values.
Some AT91 sub-architecture specific files are slightly touched by this patch
but it cannot be split because it can break compilation.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add context parameter to device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to allow passing client/target specific information associated
with the data transfer.
Modify all affected DMA engine drivers.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
As the SDMA controller can operate without an external firmware being loaded,
treat the firmware related messages as warnings rather than errors.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
For simple modules that contain a single amba_driver without any
additional setup code then ends up being a block of duplicated
boilerplate. This patch adds a new macro, module_amba_driver(),
which replaces the module_init()/module_exit() registrations with
template functions.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/dma/pl330.c: In function 'pl330_control':
drivers/dma/pl330.c:342: error: 'struct dma_pl330_chan' has no member named
'completed'
Reported by: Jassi Brar <jassisinghbrar@gmail.com>
Suggested by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Ensure all DMA engine drivers initialize their cookies in the same way,
so that they all behave in a similar fashion. This means their first
issued cookie will be 2 rather than 1, and will increment to INT_MAX
before returning 1 and starting over.
In connection with this, Dan Williams said:
> Russell King wrote:
> > Secondly, some DMA engine drivers initialize the dma_chan cookie to 0,
> > others to 1. Is there a reason for this, or are these all buggy?
>
> I know that ioat and iop-adma expect 0 to mean "I have cleaned up this
> descriptor and it is idle", and would break if zero was an in-flight
> cookie value. The reserved usage of zero is an driver internal
> concern, but I have no problem formalizing it as a reserved value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Dan Williams said:
> > Russell King wrote:
> > Firstly, we have DMA_MIN_COOKIE which has value 1 - so any cookies below
> > that aren't valid. That seems sane.
> >
> > We seem to have different behaviours:
> >
> > - cookie = c->cookie;
> > - cookie++;
> > - if (cookie < 0)
> > - cookie = 1;
> > - c->cookie = cookie;
> > - tx->cookie = cookie;
> >
> > c->cookie here is initialized to zero, so the first cookie given out will
> > be 1. This is how most DMA engine drivers implement this.
> >
> > Then we have this:
> >
> > cookie = chan->common.cookie;
> > cookie++;
> > if (cookie <= 1)
> > cookie = 2;
> >
> > /* initialize the completed cookie to be less than
> > * the most recently used cookie
> > */
> > chan->common.completed_cookie = cookie - 1;
> > chan->common.cookie = sw_desc->async_tx.cookie = cookie;
> >
> > Again, chan->common.cookie starts off at 0. The first cookie given out
> > will be 2, and 1 will never be used. There are three drivers which
> > implement it this way.
> >
> > Why is there this difference, and can these three be corrected to behave
> > the same way as the first (and therefore the assignment of cookies
> > consolidated?)
>
> Yes, they should be consolidated, and I believe they have drifted only
> because there were no good common helpers and murphy's law took over.
So lets fix this up to use the common dma_cookie_assign() helper.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Provide a common function to initialize a channels cookie values.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Now that we have the completed cookie in the dma_chan structure, we
can consolidate the tx_status functions by providing a function to set
the txstate structure and returning the DMA status. We also provide
a separate helper to set the residue for cookies which are still in
progress.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Provide a common function to do the cookie mechanics for completing
a DMA descriptor.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Everyone deals with assigning DMA cookies in the same way (it's part of
the API so they should be), so lets consolidate the common code into a
helper function to avoid this duplication.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add a local private header file to contain definitions and declarations
which should only be used by DMA engine drivers.
We also fix linux/dmaengine.h to use LINUX_DMAENGINE_H to guard against
multiple inclusion.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Every DMA engine implementation declares a last completed dma cookie
in their private dma channel structures. This is pointless, and
forces driver specific code. Move this out into the common dma_chan
structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
mv_xor's is_complete_cookie is only ever written to, but never read.
This is silly, remove the write-only structure member.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
[imx-sdma.c & mxs-dma.c]
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This reverts commit 865d9438eb.
The module.h incsuion twice has been updated tree wide hence this is not
required to be merged.
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The DMAC PL330 r1p0 version fixed the lockup error being on r0p0.
This patch supports the DMA transmission without memory barrier
operation when the revision of DMAC PL330 is the next of r0p0.
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Currently there were two part of DMAC PL330 driver for
support old styled s3c-pl330 which has been merged into
drivers/dma/pl330.c driver. Actually, there is no reason
to separate them now.
Basically this patch merges arch/arm/common/pl330.c into
drivers/dma/pl330.c driver and removes useless exported
symbol, externed function and so on.
The newer pl330 driver tested on SMDKV310 and SMDK4212 boards
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add support for the SA-11x0 DMA driver, which replaces the private
API version in arch/arm/mach-sa1100/dma.c.
We model this as a set of virtual DMA channels, one for each request
signal, and assign the virtual DMA channel to a physical DMA channel
when there is work to be done. This allows DMA users to claim their
channels, and hold them while not in use, without affecting the
availability of the physical channels.
Another advantage over this approach, compared to the private version,
is that a channel can be reconfigured on the fly without having to
release and re-request it - which for the IrDA driver, allows us to
use DMA for SIR mode transmit without eating up three physical
channels. As IrDA is half-duplex, we actually only need one physical
channel, and this architecture allows us to achieve that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Print a message when firmare fails to be requested in the case of platform data being used.
While at it, distinguish between the error messages of the device tree and platform data cases.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
On the device tree case the code bails out when the firmware name cannot be found
or if the firmware fails to be requested.
Fix this behaviour as the SDMA engine can still operate with the built-in
ROM scripts.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
dmaengine specifies the possibility that several descriptors
can be queued for transfer. It also indicates that tasklets
must be used for DMA callbacks.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
MEMCPY transfers allow DMA copies from memory to
memory. This patch has been tested with dmatest
device driver.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The message "dmaengine: failed to get" can come from two possible locations within dmaengine.c.
In order to distinguish between them, replace "dmaengine" with __func__ string so that the
source function of the error message can be easily identified.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
drivers/dma/imx-dma.c and drivers/dma/imx-sdma.c included
'linux/module.h' twice, remove the duplicates.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Different tree maintainers picked up independently generated
trivial compile fixes based on linux-next testing, resulting
in some cases where a file would have got more than one addition
of module.h once everything was all merged together.
Delete any duplicates so includecheck isn't complaining about
anything related to module.h/export.h changes.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This patch adds support for DMA_SLAVE_CONFIG in dwc DMAC controller. Fields in
struct dw_dma_slave for passing similar data are preserved in this patch untill
all existing users are fixed.
That will be handled later in this patchset.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
64 bit transfers are possible on both sides in slave transfers (memory as well
as peripherals). This patch adds support for it memory side 64 bit transfers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Block interrupts give interrupt on completion of every LLI, which is actually
too much interrupts. This is just not required for current functioning of
dw_dmac.
So, just don't handle them at all.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Use already defined function dev_get_platdata() instead of accessing
pdev->dev.data.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Total number of channels is passed in pdata->nr_channels variable, thus we must
not use magic number '7' for total number of channels.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Flow controller information is passed now from DMA_SLAVE_CONFIG option. This
patch makes changes in pl08x driver to use device_fc from it instead of platform
data.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The suspend and resume implementation is through dev_pm_ops in dmac. So
in order to support hibernation, freeze, thaw, restore and poweroff
features are required.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Move pm_runtime_put() to the end of intel_mid_dma_free_chan_resources()
because there is no sense in allowing runtime suspend while the driver
is still accessing the device.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The error status mask (MASK_ERR) has the same format as the other
masks (MASK_TFR, MASK_BLOCK etc) and must be cleared the same way.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Commit 6584cb88 (ARM i.MX dma: Fix burstsize settings) fixed
the mxcmmc driver but forgot to fix the SDMA driver to handle the
correct burtsize.
This make the SD card access works again with DMA on i.MX31 boards.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Commit 6584cb88 (ARM i.MX dma: Fix burstsize settings) fixed
the mxcmmc driver but forgot to fix the SDMA driver to handle the
correct burtsize.
This make the SD card access works again with DMA on i.MX31 boards.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add a flag to allow platforms to specify, whether a DMAC instance supports
the MEMCPY operation. To avoid regressions, preserve the current default.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
commit 463894705e deleted redundant
chan_id and chancnt initialization in dma drivers as this is done
in dma_async_device_register().
However, atc_enable_irq() relied on chan_id set before registering
the device, what left only channel 0 functional for this driver.
This patch introduces atc_enable/disable_chan_irq() as a variant
of atc_enable/disable_irq() with the channel as explicit argument.
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
We don't need extra lock, so we use non-atomic bit ops to set/clear bits,
merge event_mask0 and event_mask1 into an array, it helps use bit ops.
It also fixs the issue:
sdmac->event_mask0 = 1 << sdmac->event_id0;
sdmac->event_mask1 = 1 << (sdmac->event_id0 - 32);
It event_id0 < 32, it shifts negative number. If event_id0 >= 32, it
shifts number >= sizeof(int). Both the cases behavior is undefined.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
event number is not always 32. use num_events for checking instead.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
It makes clk_enable/disable pair more readable, and fix one bug:
sdma_init calls sdma_request_channel, but seems don't know
sdma_request_channel enabled the clock.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
[fixed typo in commit log]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
sdma_request_channel sets the default priority. sdma_alloc_chan_resources
should call sdma_set_channel_priority thereafter to over write it.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
use readl_relaxed/writel_relaxed in most places, and use writel when
enable channel, because it needs memory barrier.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Rewrite a duplicated test to test the correct value
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
This patch additionally adds calls to clk_disable and clk_put.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The DMA engine API requires that transfers are started in issue_pending
instead of tx_submit. Fix this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[corrected change log to DMA engine API insteadof DMA API]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The DMA engine API requires that transfers are started in issue_pending
instead of tx_submit. Fix this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[corrected change log to DMA engine API insteadof DMA API]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Hi,
On the latest tree my compiler has started giving the warning:
drivers/dma/dmatest.c:575:28: warning: the omitted middle operand in ?: will always be ?true?, suggest explicit middle operand [-Wparentheses]
The following patch fixes the missing middle clause with the same
fix that Nicolas Ferre used in the similar clauses.
(There seems to have been a race between him fixing that and
the extra clause going in a little later).
I don't actually know the dmatest code/structures, nor do I own
any hardware to test it on (assuming it needs a DMA engine);
but this patch builds, the existing code is almost certainly
wrong and the fix is the same as the corresponding lines above it.
(WTH is x=y?:z legal C anyway?)
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Another simple series related to clock management, this time only for
imx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=czKE
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
clock management changes for i.MX
Another simple series related to clock management, this time only for
imx.
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: select HAVE_CLK_PREPARE for clock
clk: add config option HAVE_CLK_PREPARE into Kconfig
ASoC: mxs-saif: convert to clk_prepare/clk_unprepare
video: mxsfb: convert to clk_prepare/clk_unprepare
serial: mxs-auart: convert to clk_prepare/clk_unprepare
net: flexcan: convert to clk_prepare/clk_unprepare
mtd: gpmi-lib: convert to clk_prepare/clk_unprepare
mmc: mxs-mmc: convert to clk_prepare/clk_unprepare
dma: mxs-dma: convert to clk_prepare/clk_unprepare
net: fec: add clk_prepare/clk_unprepare
ARM: mxs: convert platform code to clk_prepare/clk_unprepare
clk: add helper functions clk_prepare_enable and clk_disable_unprepare
Fix up trivial conflicts in drivers/net/ethernet/freescale/fec.c due to
commit 0ebafefcaa ("net: fec: add clk_prepare/clk_unprepare") clashing
trivially with commit e163cc97f9 ("net/fec: fix the .remove code").
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=N2B4
-----END PGP SIGNATURE-----
Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
This is where the really nasty conflicts in the samsung platform
start, due to some files getting moved around and combined in the
'restart' branch that has already gone into mainline through
Russell's tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XY2N
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Device tree conversions for samsung and tegra
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
ARM: EXYNOS: Add Exynos4 device tree enabled board file
rtc: rtc-s3c: Add device tree support
input: samsung-keypad: Add device tree support
ARM: S5PV210: Modify platform data for pl330 driver
ARM: S5PC100: Modify platform data for pl330 driver
ARM: S5P64x0: Modify platform data for pl330 driver
ARM: EXYNOS: Add a alias for pdma clocks
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
DMA: PL330: Add device tree support
ARM: EXYNOS: Modify platform data for pl330 driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
DMA: PL330: move filter function into driver
serial: samsung: Fix build for non-Exynos4210 devices
serial: samsung: add device tree support
serial: samsung: merge probe() function from all SoC specific extensions
serial: samsung: merge all SoC specific port reset functions
ARM: SAMSUNG: register uart clocks to clock lookup list
serial: samsung: remove all uses of get_clksrc and set_clksrc
...
Fix up fairly trivial conflicts in arch/arm/mach-s3c2440/clock.c and
drivers/tty/serial/Kconfig both due to just adding code close to
changes.
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
Conflicts:
arch/arm/mach-exynos/Makefile
arch/arm/mach-exynos/cpu.c -> common.c
arch/arm/mach-exynos/include/mach/entry-macro.S
arch/arm/mach-exynos/init.c -> common.c
arch/arm/mach-s5p64x0/init.c -> common.c
arch/arm/mach-s5pv210/init.c -> common.c
Multiple files were moved into common.c files in the rmk/for-linus
branch, so this moves over the samsung/dt changes to the new
files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
On platforms, supporting power domains, if the domain, containing a DMAC
instance is powered down, the driver fails to resume correctly. On those
platforms DMAC channels have an additional CHCLR register for clearing
channel buffers. Using this register during runtime resume fixes the
problem.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
mx53_loco: fix deadlock report from sdma_tx_submit() during boot
BugLink: http://bugs.launchpad.net/bugs/878701
Adjust to use spin_lock_irqsave()/spin_unlock_irqresotre(), so to
make it safe when called from interrupt context.
Signed-off-by: Haitao Zhang <haitao.zhang@linaro.org>
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Otherwise if a previously physical channel is used as a logical channel, the
LNK may have old values which affect the operation of the logical channel since
the LNK register has different semantics between physical and logical channels.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Drivers should not support both legacy pm and new framework.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The patch converts mxs-dma driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Two issues are fixed:
1. DMA descriptors are reused so when freeing lli structures
that are linked to them, the pointer must be nulled.
2. midc_scan_descriptors() must be called with the
channel lock held.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Before dma_transfer_direction was introduced to replace
dma_data_direction, some dmaengine device uses DMA_NONE of
dma_data_direction for some talk with its client drivers.
The mxs-dma and its clients mxs-mmc and gpmi-nand are such case.
This patch adds DMA_TRANS_NONE to dma_transfer_direction and
migrate the DMA_NONE use in mxs-dma to it.
It also fixes the compile warning below.
CC drivers/dma/mxs-dma.o
drivers/dma/mxs-dma.c: In function ‘mxs_dma_prep_slave_sg’:
drivers/dma/mxs-dma.c:420:16: warning: comparison between ‘enum dma_transfer_direction’ and ‘enum dma_data_direction’
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This is how the original Freescale code (unintentionally) worked,
because the code path which would have asserted the CLKGATE bit was
never actually reached in their code.
This fixes the nefarious "DMA timout" bug when multiple DMA channels
(e.g. GPMI NAND and MMC) are used at the same time.
If a better fix for this problem should be found, the clkgate handling
could be reinstated.
See http://lists.infradead.org/pipermail/linux-arm-kernel/2011-September/065228.html
Also reverse the order of mxs_dma_disable_chan() and
mxs_dma_reset_chan() in mxs_dma_control() because mxs_dma_reset_chan()
can only work when the DMA channel is enabled.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Using a static variable for counting the number of CCWs attached to
a DMA channel when appending a new descriptor is not multi user safe.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
There is no need to have the clock enabled all the time the driver is
loaded.
It will be enabled anyway in mxs_dma_alloc_chan_resources() when a
channel is actually going to be used.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
For PL330 dma controllers instantiated from device tree, the channel
lookup is based on phandle of the dma controller and dma request id
specified by the client node. During probe, the private data of each
channel of the controller is set to point to the device node of the
dma controller. The 'chan_id' of the each channel is used as the
dma request id.
Client driver requesting dma channels specify the phandle of the
dma controller and the request id. The pl330 filter function
converts the phandle to the device node pointer and matches that
with channel's private data. If a match is found, the request id
from the client node and the 'chan_id' of the channel is matched.
A channel is found if both the values match.
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The transfer direction for a channel can be inferred from the transfer
request and the need for specifying transfer direction in platfrom data
can be eliminated. So the structure definition 'struct dma_pl330_peri'
is no longer required.
The channel's private data is set to point to a channel id specified in
the platform data (instead of an instance of type 'struct dma_pl330_peri').
The filter function is correspondingly modified to match the channel id.
With the 'struct dma_pl330_peri' removed from platform data, the dma
controller transfer capabilities cannot be inferred any more. Hence,
the dma controller capabilities is specified using platform data.
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The dma channel selection filter function is moved from plat-samsung
into the pl330 driver. In additon to that, a check is added in the
filter function to ensure that the channel on which the filter has
been invoked is pl330 channel instance (and avoid any incorrect
access of chan->private in a system with multiple types of DMA
drivers).
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ARCH_MX3 was removed in commit a89cf59 :
"arm/imx: merge i.MX3 and i.MX6"
thus preventing to select MX3_IPU, thus preventing IPU and display
to work on i.MX3x SOC.
i.MX SDMA support is also affected.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use an getter function in plat-orion/addr-map.c to get the address map
structure, rather than pass it to drivers in the platform_data
structures. When the drivers are built for none orion platforms, a
dummy function is provided instead which returns NULL.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Vinod Koul