This patch implements advice by Ben Hutchings to change the mii side of
the function names to look more like the register whose values they
convert. New LPA translation functions have been added as well.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Translating between ethtool advertisement settings and MII
advertisements are common operations for ethernet drivers. This patch
adds a set of helper functions that implements the conversion. The
patch then modifies a couple of the drivers to use the new functions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are references to this PHY chip in the generic mii.h header, so removing them.
Re-jiggle the changed comments, in response to points raised by Ben Hutchings.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whitespace changes - spaces converted to tabs after each define name and value
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes to code to use some of the preprocessor
definitions from mii.h over its homegrown equivalents.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
This converts flow control capabilites to an advertising mask and can
be useful in combination with mii_resolve_flowctrl_fdx().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a shorter and more comprehensible formulation of the
conditions for each flow control mode.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These 4 drivers have identical full duplex flow control resolution
functions. This patch changes them all to use one common function.
The function in question decides whether a device should enable TX and
RX flow control in a standard way (IEEE 802.3-2005 table 28B-3), so this
should also be useful for other drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flags used within drivers for indicating tx and rx flow control are
defined in 4 drivers (and probably more), move these constants to mii.h.
The 3 SMSC drivers use the same constants (FLOW_CTRL_TX), but TG3 uses
TG3_FLOW_CTRL_TX, so this patch also renames the constants within TG3.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They shouldn't be using 'u32' et al in structures which are used for
communication with userspace. Switch to the proper types (__u32 etc).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
A new driver bnx2 for Broadcom bcm5706 is available.
The patch also includes new 1000BASE-X advertisement bit definitions in
mii.h
Thanks to David Miller and Jeff Garzik for reviewing and their valuable
feedback.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Matt Carlson