Multiple devices from the ADAU family share the same PLL structure and
configuration register layout. Introduce a new helper module that can be
used to calculated the PLL configuration registers based on a specified
input frequency and the desired output frequency of the PLL.
The ADAU1761/ADAU1781 and ADAU1373 drivers are updated to make use of this
new helper module. But future drivers for additional devices from the ADAU
family are also expected to make use of it.
In anticipation of sharing more infrastructure code between different
devices from the ADAU family the new module is called adau-utils.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new
drivers. Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uNKQ
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound updates from Takashi Iwai:
"This is the second update round for 4.7-rc1. Most of changes are
about the pending ASoC updates and fixes, including a few new drivers.
Below are some highlights:
ASoC:
- New drivers for MAX98371 and TAS5720
- SPI support for TLV320AIC32x4, along with the module split
- TDM support for STI Uniperf IPs
- Remaining topology API fixes / updates
HDA:
- A couple of Dell quirks and new Realtek codec support"
* tag 'sound-4.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (63 commits)
ALSA: hda - Fix headset mic detection problem for one Dell machine
spi: spi-ep93xx: Fix the PTR_ERR() argument
ALSA: hda/realtek - Add support for ALC295/ALC3254
ASoC: kirkwood: fix build failure
ALSA: hda - Fix headphone noise on Dell XPS 13 9360
ASoC: ak4642: Enable cache usage to fix crashes on resume
ASoC: twl6040: Disconnect AUX output pads on digital mute
ASoC: tlv320aic32x4: Properly implement the positive and negative pins into the mixers
rcar: src: skip disabled-SRC nodes
ASoC: max98371 Remove duplicate entry in max98371_reg
ASoC: twl6040: Select LPPLL during standby
ASoC: rsnd: don't use prohibited number to PDMACHCRn.SRS
ASoC: simple-card: Add pm callbacks to platform driver
ASoC: pxa: Fix module autoload for platform drivers
ASoC: topology: Fix memory leak in widget creation
ASoC: Add max98371 codec driver
ASoC: rsnd: count .probe/.remove for rsnd_mod_call()
ASoC: topology: Check size mismatch of ABI objects before parsing
ASoC: topology: Check failure to create a widget
ASoC: add support for TAS5720 digital amplifier
...
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While building m32r allmodconfig the build failed with:
ERROR: "bad_dma_ops" [sound/soc/kirkwood/snd-soc-kirkwood.ko] undefined!
To satisfy the dependency CONFIG_SND_KIRKWOOD_SOC should depend on
HAS_DMA.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any
core code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QsAc
-----END PGP SIGNATURE-----
Merge tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This time was again a relatively calm development cycle; most of
updates are about drivers, and no radical changes are seen in any core
code. Here are some highlights:
ALSA core:
- Continued hardening of ALSA hrtimer
- A few leak fixes in timer interface
- Fix poll error handling in PCM and compress
- Add error propagation in compress API
- Removal of dead rtctimer driver
HD-audio:
- Native ELD notify support for i915 HDMI
- Realtek ALC234 & co support
- Code refactoring to standardize chmap support
- Continued development for SKL HDMI core support
Firewire:
- Apply delayed card registration to all drivers
- Improved / stabilized the handling of PCM stream start / stop
- Add tracepoints to dump a part of isochronous packet data
- Fixed incoming/outgoing packet parameter usages
- Add support for M-Audio profire series
USB-audio:
- Fixes for UAC2 clock source
- SS+ support
- Workaround for oft-seen repeated sample rate read errors
ASoC:
- Further slow progress on the topology code
- Substantial updates and improvements for the da7219, es8328,
fsl-ssi, Intel and rcar drivers.
- Compress error handling in WM ADSP driver"
* tag 'sound-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (177 commits)
ALSA: firewire-lib: change a member of event structure to suppress sparse wanings to bool type
sound: oss: Use setup_timer and mod_timer.
ASoC: hdac_hdmi: Remove the unused 'timeout' variable
ASoC: fsl_ssi: Fix channel slipping on capture (or playback) restart in full duplex.
ASoC: fsl_ssi: Fix channel slipping in Playback at startup
ASoC: fsl_ssi: Fix samples being dropped at Playback startup
ASoC: fsl_ssi: Save a dev reference for dev_err() purpose.
ASoC: fsl_ssi: The IPG/5 limitation concerns the bitclk, not the sysclk.
ASoC: fsl_ssi: Real hardware channels max number is 32
ASoC: pcm5102a: Add support for PCM5102A codec
ASoC: hdac_hdmi: add link management
ASoC: Intel: Skylake: add link management
ALSA: hdac: add link pm and ref counting
ALSA: au88x0: Fix zero clear of stream->resources
ASoC: rt298: Add DMI match for Broxton-P reference platform
ASoC: rt298: fix null deref on acpi driver data
ASoC: dapm: deprecate MICBIAS widget type
ALSA: firewire-lib: drop skip argument from helper functions to queue a packet
ALSA: firewire-lib: add context information to tracepoints
ALSA: firewire-lib: permit to flush queued packets only in process context for better PCM period granularity
...
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXPVb9AAoJEHwUBw8lI4NHnDQP/AtUYBTI8XD68iGh5eCTEtwO
3dNgUmOvIAIl0ZtVKex3b7j2S52IN7EDv44QmsmvMHgjvaupUsZ/HeIHgoI37y39
/qoRkyiG75ht68BrNjKcpJLsOyxaAUT1tMyf/bYXlDW8O7qEPtRDhuvUB+i+s3RX
ljNOQXH2WaQTJrNeZxkvbp92iGiu3j7AKyCh9MJ4gnF4y2oA1bFp++QpH5qcBOTp
0nccs7pgDQhw2nzHmhYbEmvgcKPrPQi+67U7eIed7n7wiThAIXIEbZl6AYk9kFaK
gSa4/N3fwnZc9TFR5O6qdanvsYdW4JC1P5Ydm0opExo3lgtMckQ3sGKFIwTG8eU4
YiyQE1uVHRqT82zxPCecTF+I0Y4g68oCJURrHED6kxKGA5a8ojU04aGebXDiNKlp
FEDceEC5ch7ZPw8CCTola+TYpf9Vni3g7OkrdkPY9cX/aDXDROghTCg9jgPJ2aL/
oai5axc5gQMEFzHPaEwFp45tgXw7IvIzaqYHmiWE11fsRbGUSB2HAwBXytI9ReC0
XTMBvc08YvisbIpIR29T0R5cerzdDuK9bXxYHHHOeUFg0t8R8UGaP1UxEQCVmLsT
AIrHupoccPJ7IAn0h6mShtZ2yzBfj3rU4tEMJR/Oj/VvjW3gKbbZ5XVi92fOurBs
xjn9uBBZ/Pt9hgprwlmY
=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
The ak4642 driver is using a regmap cache sync to restore the
configuration of the chip on resume but (as Peter observed) does not
actually define a register cache which means that the resume is never
going to work and we trigger asserts in regmap. Fix this by enabling
caching.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Disconnect also the path to AUXL from the HF path during digital_mute to
avoid pop noise leakage to Line-out pads.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
* acpi-pci:
ACPI,PCI,IRQ: remove SCI penalize function
ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()
ACPI,PCI,IRQ: reduce static IRQ array size to 16
ACPI,PCI,IRQ: reduce resource requirements
* acpi-misc:
ACPI / sysfs: fix error code in get_status()
ACPI / device_sysfs: Clean up checkpatch errors
ACPI / device_sysfs: Change _SUN and _STA show functions error return to EIO
ACPI / device_sysfs: Add sysfs support for _HRV hardware revision
arm64: defconfig: Enable ACPI
ACPI / ARM64: Remove EXPERT dependency for ACPI on ARM64
ACPI / ARM64: Don't enable ACPI by default on ARM64
acer-wmi: Use acpi_dev_found()
eeepc-wmi: Use acpi_dev_found()
ACPI / utils: Rename acpi_dev_present()
* acpi-tools:
tools/power/acpi: close file only if it is open
Happened when the Playback (or Capture) is running continuously
and Capture (or Playback) is restarted (xrun, manual stop/start...)
Since the RX (or TX) FIFO are only reset when the whole SSI is disabled,
pending samples from previous capture (or playback) session may still
be present. They must be erased to not introduce channel slipping.
FIFO Clear register fields are documented in IMX51, IMX35 reference manual.
They are not documented in IMX50 or IMX6 RM, despite they are
working as expected on IMX6SL and IMX6solo.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, SCR.SSIEN and SCR.TE were enabled at once if no capture
stream was also running.
This may not give a chance for the DMA to write the first sample in
TX FIFO before the streaming starts on the PCM bus, inserting void
samples first.
Those void samples are then responsible for slipping the channels.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the capture is already running while playback is started, it is highly
probable (>80% in a 8 channels scenario) that samples are lost between
the DMA and TX fifo.
The reason is that SIER.TDMAE is set before STCR.TFEN0, leaving a time
window where the FIFO doesn't receive the samples written by the DMA.
This particular case happened only if capture is already enabled as
SCR.SSIEN is already set at the playback startup instant.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of functions only receive the ssi_private reference and don't have
a knowledge of 'dev' pointer, even for debug purpose.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
im6sl reference manual 47.7.4:
"
Bit clock - Used to serially clock the data bits in and out of the SSI port.
This clock is either generated internally (from SSI's sys clock) or taken
from external clock source (through the Tx/Rx clock ports).
[...]
Care should be taken to ensure that the bit clock frequency (either
internally generated by dividing the SSI's sys clock or sourced from
external device through Tx/Rx clock ports) is never greater than 1/5
of the ipg_clk (from CCM) frequency.
"
Since, in master mode, the sysclk is a multiple of bitclk, we can
easily reach a high sysclk value, whereas keeping a reasonable bitclk.
ex: 8ch x 16bit x 48kHz = 6144000, requires a 24576000 sysclk (PM=1)
yet ipg_clk/5 = 66Mhz/5 = 13.2
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max number of slots in TDM mode is 32:
- Frame Rate Divider Control is a 5bit value
- Time slot mask registers control 32 slots.
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Caleb Crome <caleb@crome.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TLV320AIC32x4 has a very flexible mixer on the inputs to the ADCs. Each
mixer has an available set of available pins that can be connected to the
ADC positive and negative pins via three different resistor values. This
allows for configuration of differential inputs as well as doing level
manipulation between sources going into the mixers.
The current code only provides positive pins and I implemented the resistors
in an earlier patch. It turns out that it appears to more accurately model
what's happening to implement each of the pins as a MUX rather than on/off
switches and a mixer. This way each pin can be set to its desired resistor
value. Since there are no switches, the mixer is no longer necessary in the
DAPM path. I set the DAPM paths such that the "off" position of any of the
MUXes turns the path off.
This should allow for any input confiuration available on the codec.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some definitions to support the PCM5102A codec
by Texas Instruments.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Changes to original patch by Florian Meier:
* rebased (Makefile and Kconfig
* fixed checkpath errors (spaces, newlines)
* added dt-binding documentation
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Manage the hda idisp link using shiny new link APIs. We need to
keep link On while we probe and also hold the reference in runtime
resume and drop in suspend
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lars-Peter Clausen