This field was marked as reserved before since we didn't
use it, but is present in all released firmwares afaict.
We're going to need it soon, so add it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a frame is sent to a sleeping station, the
microcode reports TX_STATUS_FAIL_DEST_PS as its
status -- we need to translate that to the flag
that mac80211 expects.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle BSS_CHANGED_BEACON_ENABLED to enable the sending
of beacons. Also set the correct HT RXON and QoS config.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending beacon commands to the uCode, we must
inform it of the offset in the beacon frame of the
TIM Element so it can transmit packets from the
correct queue. This functionality is implemented
in iwl_set_beacon_tim().
Fix a bug setting the rate_n_flags for the beacon
packet. First, it should not use the station table's
rate (it's a management frame), and second it needs
to properly configure the TX antennas.
Finally, also, clean up and comment relevant functions.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A recent change optimized the power usage by the device by only powering it
up during EEPROM load if it is required (for OTP devices). This change causes
an error on the 1000 series devices during module load.
The error looks as follows:
[ 1624.024524] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds
[ 1624.024527] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[ 1624.024711] iwlagn 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1624.024749] iwlagn 0000:01:00.0: setting latency timer to 64
[ 1624.024909] iwlagn 0000:01:00.0: Detected Intel Wireless WiFi Link 1000 Series BGN REV=0x6C
[ 1624.081263] iwlagn 0000:01:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080003D8
[ 1624.092967] iwlagn 0000:01:00.0: OTP is empty
[ 1624.092988] iwlagn 0000:01:00.0: Unable to init EEPROM
[ 1624.093033] iwlagn 0000:01:00.0: PCI INT A disabled
[ 1624.093065] iwlagn: probe of 0000:01:00.0 failed with error -2
Adding a dump_stack() to where that error is printed shows the following:
[ 1624.024524] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds
[ 1624.024527] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[ 1624.024711] iwlagn 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1624.024749] iwlagn 0000:01:00.0: setting latency timer to 64
[ 1624.024909] iwlagn 0000:01:00.0: Detected Intel Wireless WiFi Link 1000 Series BGN REV=0x6C
[ 1624.081263] iwlagn 0000:01:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080003D8
[ 1624.081263] Pid: 3073, comm: work_for_cpu Tainted: G W 2.6.31.5 #4
[ 1624.081263] Call Trace:
[ 1624.081263] [<ffffffffa02395db>] T.726+0x22b/0x420 [iwlcore]
[ 1624.081263] [<ffffffffa023985a>] iwlcore_eeprom_acquire_semaphore+0x8a/0x190 [iwlcore]
[ 1624.081263] [<ffffffff81110c94>] ? __kmalloc+0x194/0x1c0
[ 1624.081263] [<ffffffffa02391f5>] ? iwlcore_eeprom_verify_signature+0x25/0xf0 [iwlcore]
[ 1624.081263] [<ffffffffa0239c67>] iwl_eeprom_init+0x107/0xf40 [iwlcore]
[ 1624.081263] [<ffffffffa026ab9c>] ? iwl_prepare_card_hw+0x11c/0x470 [iwlagn]
[ 1624.081263] [<ffffffff8127e2a4>] ? pci_bus_write_config_byte+0x64/0x80
[ 1624.081263] [<ffffffffa026b1f8>] iwl_pci_probe+0x308/0xac0 [iwlagn]
[ 1624.081263] [<ffffffff810710a0>] ? do_work_for_cpu+0x0/0x30
[ 1624.081263] [<ffffffff81284912>] local_pci_probe+0x12/0x20
[ 1624.081263] [<ffffffff810710b3>] do_work_for_cpu+0x13/0x30
[ 1624.081263] [<ffffffff81075826>] kthread+0xa6/0xb0
[ 1624.081263] [<ffffffff81012fea>] child_rip+0xa/0x20
[ 1624.081263] [<ffffffff81075780>] ? kthread+0x0/0xb0
[ 1624.081263] [<ffffffff81012fe0>] ? child_rip+0x0/0x20
[ 1624.092967] iwlagn 0000:01:00.0: OTP is empty
[ 1624.092988] iwlagn 0000:01:00.0: Unable to init EEPROM
[ 1624.093033] iwlagn 0000:01:00.0: PCI INT A disabled
[ 1624.093065] iwlagn: probe of 0000:01:00.0 failed with error -2
We know that the routines in this trace, iwlcore_eeprom_acquire_semaphore
and iwlcore_eeprom_verify_signature, only access CSR registers and thus do
not need the device to be awake if it is EEPROM. But for OTP it is required
for the device to be awake to read these registers. Ensure device is awake
before accessing these registers.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Align the format for tx_statistics and rx_statistics debugfs output for
better readability
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In both 6x00 and 6x50 series, the enhanced/extended tx power table in
EEPROM is used to set the max. tx power limit.
This new tx power table is in 1/2 dBm format, which creates an issue of
possibility of 1/2 dBm loss when driver set the tx power limit; because
of driver keep track and report the tx power in dBm format.
In order to prevent the 1/2 dBm loss, keep track of the true max tx
power in 1/2 dBm format in driver; do the comparison and adjust the tx
power if needed when send tx power command to uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Power-saving logic will not re-issue a POWER_TABLE_CMD if a new command
matches the prior one. This can be bad if we re-start the device due to
e.g. uCode error; the new POWER_TABLE_CMD (required to invoke power-saving)
may match the prior POWER_TABLE_CMD issued before the uCode error.
Ensure the POWER_TABLE_CMD is sent to device when uCode is up.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issue REPLY_STATISTICS_CMD to uCode, two possible flag
can be set in the configuration flags
bit 0: Clear statistics
0: Do not clear Statistics counters
1: Clear to zero Statistics counters
Allow "clear" parameter to be set from the caller.
Add debugfs file to clear the statistics counters to help monitor and
debug the uCode behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Number of data structure for 6000 series no longer in production, the
data structure already being removed; also need to remove the external
reference define in iwl-dev.h
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drop the non-production PCI-IDs for 6x50 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Number of HT40 power parameters are not used; remove those from
iwl_channel_info data structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Temporary disable the coex function for wifi/wimax for 6x50
series until the full implementation ready.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Validate enhanced tx power entry read from EEPROM before applying the
tx power value. Different versions of EEPROM might contain different size
of table; always a good idea to make sure the entry is valid before
applying to the targeted channel.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a holdover from earlier code when we used to set
the power limit to '0' after a reset to configure the
default transmit power, ath5k interprets txpower=0 as
12.5 dBm. Fix that by just passing 0 through.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=14567
Cc: stable@kernel.org
Reported-by: Daniel Folkers <daniel.folkers@task24.nl>
Tested-by: Daniel Folkers <daniel.folkers@task24.nl>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wlan didn't know about NL80211_AUTHTYPE_AUTOMATIC and simple
setup with 'iwconfig wlan essid no-encrypt' would fail (ENOSUPP).
v2: use NDIS_80211_AUTH_AUTO_SWITCH instead of _OPEN.
This will make device try shared key auth first, then open.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Please be gentle, I'm a fs developer and this is my first foray into drivers, as
I'm tired of building ralinks driver everytime I update my kernel. Whenever I
load the rt2800pci driver my box bogs down, and a few printk's later I
discovered its because I was getting 10's of thousands of TBTT interrupts a
second. I discovered this was because we were setting the beacon timer to 0,
which is apparently what TBTT keys off of. It seems to me that we should only
be enabling TBTT when we are in a beacon transmitting mode, which from what I
can tell is in AD-HOC and other such modes where the mac80211 layer would have
given us a proper beacon_int to set the beacon timer to instead of 0. So this
is my fix, only enable TBTT if our sync mode is for beacon. This makes it so my
box doesn't die everytime I load the rt2800pci driver. Let me know if this is
acceptable, I just learned all these terms about 15 minutes ago via wikipedia,
so I really am not familiar with how this stuff is supposed to work. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression introduced in
"ath9k: avoid the copy skb->cb on every RX'd skb"
With that change, the rx status in skb->cb was left uninitialized
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current tree hits a BUG_ON in rt2x00_regbusy_read, because the eFuse EEPROM
reading code of rt2800lib uses the function without the csr_mutex locked.
Fix this by locking the csr_mutex for the of the EEPROM reading cycly and
using the _lock variants of the register reading and writing functions.
This also introcudes the register_read_lock function pointer in the
rt2800_ops structure.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers (rt2800* most notably) cannot set the RF and RT chipset in
the correct order to have the information logging in rt2x00_set_chip
be correct.
Fix this by decoupling the setting of the chipset information from the
logging of the chipset information so that drivers can determine
themselves when all information is set.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure RF302x and RF2020 chipsets are handled properly in rt2800lib
for the rt3090 chipset.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mirror the legacy Ralink driver with respect to rt2800 RF register
programming. Execute rt2800_config_channel_rt3x for all RF2020,
RF3020, RF3021 & RF3022 chipsets when operating on RT3070 devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fix some typos and punctuation in comments
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
[bart: ported the change from the older patch for rt2800usb & rt61pci]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bit value of AR_GPIO_INPUT_EN_VAL_BT_PRIORITY_BB is wrong, it should
be 0x400 and the number of bits to be right shifted is 10. Having this
wrong value in 0x4054 sometimes affects bt quality on btcoex environment.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow rt2800usb to properly detect RT307X based devices, and set the appropriate chipset values.
Signed-off-by: Gertjan van Wingede <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit b8ecd988b1.
Due to poor API call balancing by me, this commit not only broke ipw2200
if it can't find it's firmware, it broke ipw2100 basically anytime you
removed the module. At this point in the cycle, let's just put it back
to a sane state and try again next time...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a type in rt2800_config_channel_rt3x. The second write to RF
register 2 should be to RF register 3. This is confirmed by the
legacy Ralink code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fix some typos and punctuation in comments
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For my Linksys WUSB11 at76c503-i3861 device, scanning fails without
probe_delay, min_channel_time, and max_channel_time specified for the
scan request. These values were found by checking scan requests from
the at76_usb driver.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As mentioned on the linux-wireless mailing list, the current copyright
statements in the rt2x00 are meaningless, as the rt2x00 project is
not even a formal legal entity. Therefore it is better to replace
the existing copyright statements with copyright statements for the
people that actually wrote the code.
Note: Updated to the best of my knowledge with respect to who
contributed considerable amounts of code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Link tuning code from the legacy rt2570 driver turned out to be
harmful and got disabled by the commit d06193f ("rt2x00: Disable
link tuning in rt2500usb") in August 2008.
There is no reason to keep this dead code any longer so remove it
(it can still be retrieved from the git history if necessary).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is needed for at least RT3070 chip.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
eFuse EEPROM is used also by USB chips (i.e. RT3070)
so move the needed code from rt2800pci to rt2800lib.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename RXD_W0_* defines to RXINFO_W0_* ones to match naming
used for TX descriptor and by the vendor driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add rf_vals tables and rt2800_probe_hw_mode() to rt2800lib.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enclose interface specific code in rt2800[pci,usb]_probe_hw_mode()
with rt2x00_intf_is_[pci,usb]() checks.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move hw_mode information initialization code block before
HT information initialization one to match the ordering used
by rt2800pci's rt2800pci_probe_hw_mode().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800pci's rf_vals[] copy was missing values for some channels.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add rt2800_validate_eeprom() and rt2800_init_eeprom() to rt2800lib.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Factor out common code from rt2800[pci,usb]_validate_eeprom()
to rt2800_validate_eeprom().
* Fix interface specific comment in rt2800[pci,usb]_validate_eeprom().
* Enclose interface specific code in rt2800[pci,usb]_init_eeprom()
with rt2x00_intf_is_[pci,usb]() checks.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_rx_status->qual has been marked deprecated.
This allows us to remove several functions and fields which
were used to calculate a reasonable value for it.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of assuming that all rt3090 devices will have an eFuse EEPROM,
do as the legacy Ralink driver, and detect at run-time whether an
eFuse EEPROM is present.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jumbograms are frames put together linked together through
more than one descriptor. For example ath9k_htc will use this
to send from the target a large frame split up into 2 or more
segments. The driver then would be in charge of putting the
frame back together.
When jumbograms are constructed the rx_stats->rs_more will
bet set and rx_stats->rs_status will not have any valid content
as the actual status will only be avialable at the end of
the chained descriptors.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is now deprecated and unused within mac80211, so time
to remove it as otherwise we'd be doing some unecessary
computations for nothing.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k and ath9k_htc share a lot of common hardware characteristics.
They only differ in that ath9k_htc works with a target CPU and ath9k
works directly with the hardware. ath9k_htc will do *some* things in
the firmware, but a lot of others on the host.
The common 802.11n hardware code is already shared through the ath9k_hw
module. Common helpers amongst all Atheros drivers can use the ath module,
this includes ath5k and ar9170 as users. But there is some common driver
specific helpers which are not exactly hardware code which ath9k and
ath9k_htc can share. We'll be using ath9k_common for this to avoid
bloating the ath module and the common 802.11n hardware module ath9k_hw.
We start by sharing skb pre and post processing in preparation for a hand
off to mac80211.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a helper for the RX skb post processing,
ath9k_rx_skb_postprocess().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will make sharing code easier between ath9k and ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And change the return value to something more obvious.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While at it flip the order, seems easier to read and also
add some better description as to why we do this check.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k is using the (csz - 1) twice as ath_rxbuf_alloc() already allocates
and moves skb->data accordingly. Remove the extra (csz -1).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will also be used by ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The skb->cb (control buffer, 48 bytes) is available to the skb
upon skb allocation. You can fill it up imediately after skb
allocation. ath9k was copying onto the skb->cb the data from the
processed skb for mac80211 from a stack struct ieee80211_rx_status
structure. This is unnecessary, instead use the skb->cb for the
rx status immediately after the skb becomes available and DMA
synched.
Additionally, avoid the copy of the skb->cb also for virtual wiphys
as skb_copy() will copy over the skb->cb for us as well.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves all the RX processing of RSSI into a helper,
ath_rx_prepare(). ath_rx_prepare() should now be really
easy to read and follow.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the qual computing into a small helper,
ath9k_compute_qual()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_process_rate() now does all the rx status processing to
read the rate the hardware passed and translate it to whatever
mac80211 wants.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Its just a distraction when reading the code, instead use the
rx_stats->rs_rate directly.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This does sanity checking on the skb and RX status descriptor
prior to processing.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to use the private driver structure to get to an sband.
This will make it easier to share this code with ath9k_htc.
With the sc gone we can now just pass the common structure to
ath_rx_prepare().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be shared between ath9k and ath9k_htc. It will also
help with sharing routine helpers on the RX path.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be shared between ath9k and ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Its not needed, so just pass the hardware RX status.
We'll be simplfying ath_rx_prepare() with code we can share
between ath9k and ath9k_htc. This will help make that code
easier to read and manage.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k virtual wiphys all share the same internal buffer space
for TX but they do not share the mac80211 skb queues. When
ath9k detects it is running low on buffer space to TX it tells
mac80211 to stop sending it skbs its way but it always does
this only for the primary wiphy. This means mac80211 won't know
its best to avoid sending ath9k more skbs on a separate virtual
wiphy. The same issue is present for reliving the skb queue.
Since ath9k does not keep track of which virtual wiphy is hammering
on TX silence all wiphy's TX when we're low on buffer space. When
we're free on buffer space only bother informing the virtual wiphy
which is active that we have free buffers.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using virtual wiphys the base sc->hw was being used, the correct
hw is passed along the caller already so just use that.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath9k virtual wiphys are used the sc->hw will not always represent
the active hw, instead we need to get it from the skb->cb private
driver area. This ensures the right hw is used to find a sta for
the TX'd skb.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use the ieee80211_hw for radio enable/disable but the wrong
structure hw was being used in consideration for virtual wiphys
as each virtual wiphy has its own ieee80211_hw struct.
Just pass the hw struct to ensure we use the right one. This should
fix the hw used and passed for radio enable/disable. This includes
the stoping / starting of the software TX queues so mac80211 doesn't
send us data for a specific virtual wiphy. ath9k already takes care
of pausing virtual wiphys and stopping the respective queues on its
own, but this should handle the idle mac80211 conf calls as well.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this now uses the proper hw which should mean finding the
right sta when using ath9k virtual wiphy stuff. Only
advantage I see here is getting the rssi properly updated
so the 'fix' itself isn't that great, but at least this
is correct.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_get_virt_hw() is required on RX to determine for which virtual
wiphy an skb came in for. Instead of searching for the hw twice do
it only once.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports its own virtual wiphys. The hardware code
relies on the ieee80211_hw for the present interface but
with recent changes introduced the common->hw was never
updated and is required for virtual wiphys.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The way idle configuration detection was implemented as
busted due to the fact that it assumed the ath9k virtual wiphy,
the aphy, would be marked as inactive if it was not used but
it turns out an aphy is always active if its the only wiphy
present. We need to distinguish between aphy activity and
idleness so we now add an idle bool for the aphy and mark
it as such based on the passed IEEE80211_CONF_CHANGE_IDLE
from mac80211.
Previous to all_wiphys_idle would never be true when using
only one device so we never really were using
IEEE80211_CONF_CHANGE_IDLE -- we never turned the radio
off or on upon IEEE80211_CONF_CHANGE_IDLE changes as radio
changes depended on all_wiphys_idle being true either to
turn the radio on or off. Since it was always false for
one device this code was doing nothing.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I may have botched my merge conflict resolution instructions for Dave...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling rt2800usb as a built-in driver (as opposed to a as a module) the build fails. See
http://marc.info/?l=linux-wireless&m=125768687711034&w=2 for details.
Fix it by properly including <linux/usb.h> from rt2x00usb.h
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure all drivers can benefit of the assignment of the interface
type of an adapter, instead of keeping it for rt2800 only.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CCS_START_NETWORK is declared in drivers/net/wireless/rayctl.h with the
comment Values for cmd. status is previously compared to
CCS_COMMAND_COMPLETE, which is declared in the same file with the comment
Values for buffer_status. Finally, it is possible at this point that cmd
is CCS_START_NETWORK, because it is compared to that value in an enclosing
switch that has CCS_START_NETWORK as one of two case labels around this code.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the RX error path for rev>=8 devices.
The wrong register size and definitions were used.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add txq_id info to "Tx queue requesting wakeup" debug message
Add "Rx queue requesting wakeup" debug message
Move clear of CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ to be after nearby
iwl_write_prph(), since iwl_write_prph() sets it and clears it. Almost
removed it entirely, but just making sure in case someone removes the
iwl_write_prph()! Also remove unneeded priv->lock usage; this is now
handled by priv->reg_lock within iwl_clear_bit().
Join a couple of lines that had unneeded line returns.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turn on RTS/CTS for HT to prevent uCode TX fifo underrun
This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Follow-up to "update write pointers for all tx queues after wakeup"; that
patch changed iwl_irq_tasklet_legacy(), but not iwl_irq_tasklet(), so
newer devices were not covered.
Comments from original patch:
Wakeup interrupt has been updating write pointers (indexes, actually) only
for tx queues 0-5. This is adequate just for 3945, but inadequate for other
devices, all of which have more tx queues. Now updating all tx/command queues,
so device can be aware of all new tx and host commands enqueued while
device was asleep.
This can potentially improve data traffic bandwidth and/or latency.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take advantage of device's auto-increment for SRAM reads to eliminate extra
write address accesses.
Grab/release NIC access before/after entire read sequence, rather than for
each read individually.
After a quick check of dmesg logs, this seems to double Event Log dump speed,
reducing from about 20 milliseconds to about 10 milliseconds for 512 entries
using 3945.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If device provides bad values for Event Log parameters (due to being asleep
or SRAM corruption, etc.), the size can be very, very large (e.g. 0xa5a5a5a5),
which can flood system log.
Sanity-check capacity and next_entry values and limit to reasonable size dump.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not use AP's SM_PS setting for our own SM_PS setting.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the support for all the PCI_IDs never make into production
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different channel has different configuration, need to pass correct
configuration to uCode when send "channel switch" command to uCode.
Invalid configuration will cause sysassert in uCode and produce
un-expected result.
Even it is a very small windows, but we also need to consider and handle
the case if commit_rxon occurred before the "channel switch
announcement" notification received from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is part of the code, but the comment doesn't have it,
add pointers to the code and the FIFO usage for 5000 and
up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove un-used parameter "recovery_rxon" from "priv" data structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added that code setting the swq_id, I evidently
did not understand the distinction between FIFO and TX
queue yet and added code to compare a queue ID and a
FIFO number, which is bogus.
However, the code there need not be this specific, it
can just set all queues to the identity mapping which
will be overwritten by the aggregation queue code. As
a bit of defensive coding, don't assign an swq_id to
the command queue so that if we ever use it for frames
we notice quickly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fourth queue (command queue) is already activated in
the loop above that also maps it to the command FIFO and
therefore doesn't need to be marked as activated again.
Also change the TODO comment to be accurate -- we need
to initialise the _queues_, not FIFOs, and map them to
device FIFOs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For both 6x00 and 6x50 series devices, periodic Tx IQ calibration is
disabled in uCode, driver do not need to set the periodic Tx/IQ calibration
bit in calibration command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use configured valid rx chains in scan command instead of ANT_ABC, correcting
valid rx chain configuration of 4965, should be ANT_ABC instead of ANT_AB.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing scan in power saving mode, choose only 1 valid RX chain instead of
turning all chains on.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To help debug rx related issues, if IWL_DEBUG_RADIO flag is set, print
the rxon configuration when rxon host command send to uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allocate 128 bytes linear buffer for rx skb. The first 64 bytes is
reserved for mac80211 usage (for radiotap header expansion, etc).
The frame header starts from the second 64 bytes.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since these messages indicate failure we would be interested in seeing them
always.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not mess with the original skb, but allocate an independent bouncebuffer.
This protects against bad interference with mac80211's assumptions about
the skb (which already caused bugs).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turn on RTS/CTS for HT to prevent uCode TX fifo underrun
This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configuration of wake-on-lan for unicast, multicast, broadcast, physical
activity was not working. Kernel panic issue was there when user tries to
disable WOL. Fixed them.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to a missing header include, sparse generates the following warnings:
CHECK drivers/net/wireless/rtl818x/rtl8187_rfkill.c
warning: symbol 'rtl8187_rfkill_init' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_poll' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_exit' was not declared. Should it be static?
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the GPIOs for the BenQ Joybook netbook.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add GPIO configuration for the Compaq CQ60 laptop
Reported-by: David Dreggors <ddreggors@jumptv.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should not zero out the multicast hash when configuring
the operating mode, since a zero value means all multicast
frames will get dropped. Also, ath5k_mode_setup() gets
called after any reset, so the hash already set up in
configure_filter() is lost.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ops->set_tim() must be atomic, so b43 trying to acquire a mutex leads
to a kernel crash. This patch trades an easy to trigger crash in AP
mode for an unlikely race condition. According to Michael, the real
fix would be to allow set_tim() to sleep, since b43 is not the only
driver that needs to sleep in all callbacks.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net/fsl_pq_mdio: add module license GPL
can: fix WARN_ON dump in net/core/rtnetlink.c:rtmsg_ifinfo()
can: should not use __dev_get_by_index() without locks
hisax: remove bad udelay call to fix build error on ARM
ipip: Fix handling of DF packets when pmtudisc is OFF
qlge: Set PCIe reset type for EEH to fundamental.
qlge: Fix early exit from mbox cmd complete wait.
ixgbe: fix traffic hangs on Tx with ioatdma loaded
ixgbe: Fix checking TFCS register for TXOFF status when DCB is enabled
ixgbe: Fix gso_max_size for 82599 when DCB is enabled
macsonic: fix crash on PowerBook 520
NET: cassini, fix lock imbalance
ems_usb: Fix byte order issues on big endian machines
be2net: Bug fix to send config commands to hardware after netdev_register
be2net: fix to set proper flow control on resume
netfilter: xt_connlimit: fix regression caused by zero family value
rt2x00: Don't queue ieee80211 work after USB removal
Revert "ipw2200: fix oops on missing firmware"
decnet: netdevice refcount leak
netfilter: nf_nat: fix NAT issue in 2.6.30.4+
...
Slip and a few other drivers use the same ioctl numbers on
tty devices that are normally meant for sockets. This causes
problems with our compat_ioctl handling that tries to convert
the data structures in a different format.
Fortunately, these five drivers all use 32 bit compatible
data structures in the ioctl numbers, so we can just add
a trivial compat_ioctl conversion function to each of them.
SIOCSIFENCAP and SIOCGIFENCAP do not need to live in
fs/compat_ioctl.c after this any more, and they are not
used on any sockets.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the 88w8366 firmware receive descriptor format,
and add the 88w8366 PCI ID.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the AP version of the GET_HW_SPEC command, as well as the
SET_HW_SPEC command, for initialising AP firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the AP version of the command uses a different format.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As different chip/firmware combinations support different
interface types.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the receive descriptor format is determined by the firmware running
on the hardware and not by the hardware itself, and as these
descriptor formats vary a bit between different firmware releases,
abstract out the receive descriptor init/refill/process methods, and
allow choosing between different formats at run time depending on the
chip and firmware we're running on.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of reading back the unmap address from the receive
descriptor when doing receive processing, use DECLARE_PCI_UNMAP_ADDR
and pci_unmap_addr{,set}() to keep track of these addresses.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AP and STA firmware images provide a different signature in the
HIU_INT_CODE register after loading. Record which of the signatures
we saw, as it determines which command sequences to use later on.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To allow use of a more flexible firmware file naming scheme.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for adding support for more device types, introduce a
new structure, mwl8k_device_info, where per-device information can
be stored, and change the pci id table driver data from an integer
indicating only the part number to a pointer to a mwl8k_device_info
structure.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The qual member of ieee80211_rx_status is deprecated. As a result, this
driver no longer needs to calculate a quality value.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the deprecation of the qual member of ieee80211_rx_status, that
calculation and an associated constant can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg