correct is CXD2841ER and CXD2854ER
incorrect was CXD2441ER and CXD2454ER
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
now when new tuning parameters specified demod should retune.
Also ISDB-T frequency offset calculation added
(cxd2841er_get_carrier_offset_i).
While here, fix re-tune for DVB-C Annex A, using the desired
bandwidth, instead of using 8MHz.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Avoid error message:
cxd2841er_read_status_s(): invalid state 1
Always force demod to shutdown state before initializing
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
CXD2854ER is identical to CXD2841ER except ISDB-T/S added.
New method 'cxd2841er_attach_i' is added
xtal frequency now configurable. Available options:
20.5MHz, 24MHz, 41MHz
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is Sony HELENE DVB-S/S2 DVB-T/T2 DVB-C/C2 ISDB-T/S tuner
driver (CXD2858ER).
Tuner is used on NetUP Dual Universal DVB CI card (hardware revision 1.4).
Use 'helene_attach_s' to attach tuner in 'satellite mode'.
Use 'helene_attach' for 'terrestrial mode'.
Satellite delivery systems supported:
DVB-S/S2, ISDB-S
Terrestrial delivery systems supported:
DVB-T/T2, ISDB-T
Cable delivery systems supported:
DVB-C/C2
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pull i2c updates from Wolfram Sang:
- Peter Rosin did some major rework on the locking of i2c muxes by
seperating parent-locked muxes and mux-locked muxes.
This avoids deadlocks/workarounds when the mux itself needs i2c
commands for muxing. And as a side-effect, other workarounds in the
media layer could be eliminated. Also, Peter stepped up as the i2c
mux maintainer and will keep an eye on these changes.
- major updates to the octeon driver
- add a helper to the core to generate the address+rw_bit octal and
make drivers use it
- quite a bunch of driver updates
* 'i2c/for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (84 commits)
i2c: rcar: add DMA support
i2c: st: Implement bus clear
i2c: only check scl functions when using generic recovery
i2c: algo-bit: declare i2c_bit_quirk_no_clk_stretch as static
i2c: tegra: disable clock before returning error
[media] rtl2832: regmap is aware of lockdep, drop local locking hack
[media] rtl2832_sdr: get rid of empty regmap wrappers
[media] rtl2832: change the i2c gate to be mux-locked
[media] si2168: change the i2c gate to be mux-locked
iio: imu: inv_mpu6050: change the i2c gate to be mux-locked
i2c: mux: document i2c muxes and elaborate on parent-/mux-locked muxes
i2c: mux: relax locking of the top i2c adapter during mux-locked muxing
i2c: muxes always lock the parent adapter
i2c: allow adapter drivers to override the adapter locking
i2c: uniphier: add "\n" at the end of error log
i2c: mv64xxx: remove CONFIG_HAVE_CLK conditionals
i2c: mv64xxx: use clk_{prepare_enable,disable_unprepare}
i2c: mv64xxx: handle probe deferral for the clock
i2c: mv64xxx: enable the driver on ARCH_MVEBU
i2c: octeon: Add workaround for broken irqs on CN3860
...
The ds3000 driver returned 1 as an error code in many places.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using div_u64() instead of do_div() makes the code slightly more
readable by humans.
[mchehab@osg.samsung.org: originally, this patch was proposed as a bug
fix for a gcc bug. This was solved already, but it is still better to
use div_u64, instead of do_div, so I'm applying it, removing the
comments about the gcc bug]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The root i2c adapter lock is then no longer held by the i2c mux during
accesses behind the i2c gate, and such accesses need to take that lock
just like any other ordinary i2c accesses do.
So, declare the i2c gate mux-locked, and zap the regmap overrides
that makes the i2c accesses unlocked and use plain old regmap
accesses. This also removes the need for the regmap wrappers used by
rtl2832_sdr, so deconvolute the code further and provide the regmap
handle directly instead of the wrapper functions.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The root i2c adapter lock is then no longer held by the i2c mux during
accesses behind the i2c gate, and such accesses need to take that lock
just like any other ordinary i2c accesses do.
So, declare the i2c gate mux-locked, and zap the code that makes the
i2c accesses unlocked. But add a mutex so that firmware commands are
still serialized.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select/deselect ops to be in terms of the i2c mux core
instead of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix this smatch error:
dib0090.c:1124 dib0090_pwm_gain_reset() error: we previously assumed 'state->rf_ramp' could be null (see line 1086)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
s32tmp in the below code may be negative, and dev->mclk_khz is an
unsigned type.
s32tmp = 0x10000 * (tuner_frequency - c->frequency);
s32tmp = DIV_ROUND_CLOSEST(s32tmp, dev->mclk_khz);
This is undefined, as DIV_ROUND_CLOSEST is undefined for negative
dividends when the divisor is of unsigned type.
So, change mclk_khz to be signed (s32).
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change get_frontend to re-check current lock status rather than relying
on a cached value from get_status. Removes potential for tuning failure
if get_frontend is called during tuning.
Probably not too essential as other changes work around this:
https://patchwork.linuxtv.org/patch/32845/
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Do statistics polling on read status in order to avoid
unnecessary delayed work.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add callback parameter to select enable / disable slave TS and use
it when slave demod is in use.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Finalize the driver.
It still lacks a lot of features, like all statistics and PLP
filtering, but basic functionality and sensitivity is pretty good
shape.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As we want au0828 to use the core function to create the MC
graphs, use enum demod_pad_index instead of
enum au8522_media_pads.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch with -pkernel --no-data keeps complaining about rf_ramp:
drivers/media/dvb-frontends/dib0090.c:1119 dib0090_pwm_gain_reset() error: we previously assumed 'state->rf_ramp' could be null (see line 1086)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While there's no risk of divison by zero, the logic there is akward, as it
does the calculus for the numerator and denominator before checking
if this will be used.
Change the order to check first if the denominator is zero, and only
calculating the numerator/denominator if not.
This should also avoid those smatch errors:
drivers/media/dvb-frontends/drx39xyj/drxj.c:9605 ctrl_get_qam_sig_quality() debug: sval_binop_unsigned: divide by zero
drivers/media/dvb-frontends/drx39xyj/drxj.c:9605 ctrl_get_qam_sig_quality() debug: sval_binop_unsigned: divide by zero
drivers/media/dvb-frontends/drx39xyj/drxj.c:9605 ctrl_get_qam_sig_quality() debug: sval_binop_unsigned: divide by zero
drivers/media/dvb-frontends/drx39xyj/drxj.c:9605 ctrl_get_qam_sig_quality() debug: sval_binop_unsigned: divide by zero
drivers/media/dvb-frontends/drx39xyj/drxj.c:9605 ctrl_get_qam_sig_quality() debug: sval_binop_unsigned: divide by zero
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add new pad for ALSA Audio Out to au8522_media_pads.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the au8522_media_pads enum to au8522.h from au8522_priv.h to export
them. This will allow au0828-core to use these defines instead of
hard-coding them them.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both dib9000_read16_attr and dib9000_write16_attr can return an
error code. However, they currently return an u16. This produces the
following warnings on smatch:
drivers/media/dvb-frontends/dib9000.c:262 dib9000_read16_attr() warn: signedness bug returning '(-121)'
drivers/media/dvb-frontends/dib9000.c:321 dib9000_write16_attr() warn: signedness bug returning '(-22)'
drivers/media/dvb-frontends/dib9000.c:353 dib9000_write16_attr() warn: signedness bug returning '(-121)'
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As warned by smatch:
drivers/media/dvb-frontends/dib0090.c:1118 dib0090_pwm_gain_reset() error: we previously assumed 'state->rf_ramp' could be null (see line 1086)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWt9V+AAoJEHm+PkMAQRiGvqUH/iKVFxRB+MpfwRteRv22gfxJ
8Y5jDuCt2qkePHieN5JoY4FqWIA+hR+UnctHBvOCLC7DNbY79yaYuWeuShfnRVw2
91Kspk2tgnWkjlZDZ273VNKAEveFYUdhHvHFUlItWubVIlzrKRGKdAcUpecQ33YD
IERr4VFxdQDgksGPzH2FLJwcAKilWWygQ9ATTsY0xJepTC6PwxAFxrNx5qPiqOoI
aHJBzczk50y9hHEPkYeeWloyzIZUmf81BCi/VwOsbB30q4ENwkS2MMnebhOmBjLp
g9Bml8m/Fk4N+h2vbcLj6Bu+rE+bYDZDZ2Fmbupy4NbEkng3x3iaTPkG+R2hErQ=
=IdcS
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rc3' into patchwork
Linux 4.5-rc3
* tag 'v4.5-rc3': (644 commits)
Linux 4.5-rc3
epoll: restrict EPOLLEXCLUSIVE to POLLIN and POLLOUT
radix-tree: fix oops after radix_tree_iter_retry
MAINTAINERS: trim the file triggers for ABI/API
dax: dirty inode only if required
thp: make deferred_split_scan() work again
mm: replace vma_lock_anon_vma with anon_vma_lock_read/write
ocfs2/dlm: clear refmap bit of recovery lock while doing local recovery cleanup
um: asm/page.h: remove the pte_high member from struct pte_t
mm, hugetlb: don't require CMA for runtime gigantic pages
mm/hugetlb: fix gigantic page initialization/allocation
mm: downgrade VM_BUG in isolate_lru_page() to warning
mempolicy: do not try to queue pages from !vma_migratable()
mm, vmstat: fix wrong WQ sleep when memory reclaim doesn't make any progress
vmstat: make vmstat_update deferrable
mm, vmstat: make quiet_vmstat lighter
mm/Kconfig: correct description of DEFERRED_STRUCT_PAGE_INIT
memblock: don't mark memblock_phys_mem_size() as __init
dump_stack: avoid potential deadlocks
mm: validate_mm browse_rb SMP race condition
...
Instead of using the DTV properties cache directly, pass the get
frontend data as an argument. For now, everything should remain
the same, but the next patch will prevent get_frontend to
affect the global cache.
This is needed because several drivers don't care enough to only
change the properties if locked. Due to that, calling
G_PROPERTY before locking on those drivers will make them to
never lock. Ok, those drivers are crap and should never be
merged like that, but the core should not rely that the drivers
would be doing the right thing.
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This device doesn't really have a get_frontend(). All it does is
to blindly set everything to auto mode.
Remove the get_frontend(), as the code does that already,
and put the frontend changes at set_frontend, where it
belongs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tda1004x was updating the properties cache before locking.
If the device is not locked, the data at the registers are just
random values with no real meaning.
This caused the driver to fail with libdvbv5, as such library
calls GET_PROPERTY from time to time, in order to return the
DVB stats.
Tested with a saa7134 card 78:
ASUSTeK P7131 Dual, vendor PCI ID: 1043:4862
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Wall time obtained from ktime_get_real is susceptible to sudden jumps due to
user setting the time or due to NTP. Boot time is constantly increasing time
better suited for comparing two timestamps.
[mchehab@osg.samsung.com: fix trivial merge conflicts]
Signed-off-by: Abhilash Jindal <klock.android@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ts2020_remove was calling kfree(dev) with possibly still active
schedule_delayed_work(dev->stat_work). A similar bug in si2157 caused
kernel panics in call_timer_fn e.g. after rmmod cx23885.
Signed-off-by: Ernst Martin Witte <emw-linux-kernel@nocabal.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rtl2830_remove was calling kfree(dev) with possibly still active
schedule_delayed_work(&dev->stat_work). A similar bug in si2157
caused kernel panics in call_timer_fn e.g. after rmmod cx23885.
Signed-off-by: Ernst Martin Witte <emw-linux-kernel@nocabal.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
af9033_remove was calling kfree(dev) with possibly still active
schedule_delayed_work(&dev->stat_work). A similar bug in si2157
caused kernel panics in call_timer_fn e.g. after rmmod cx23885.
Signed-off-by: Ernst Martin Witte <emw-linux-kernel@nocabal.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
af9013_remove was calling kfree(state) with possibly still active
schedule_delayed_work(&state->statistics_work). A similar bug in
si2157 caused kernel panics in call_timer_fn e.g. after rmmod cx23885.
Signed-off-by: Ernst Martin Witte <emw-linux-kernel@nocabal.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The stv6110x_devctl structure is never modified, so declare it as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This issue was detected by using the Coccinelle software.
1. Let us return directly if a call of the si2165_readreg8()
function failed.
2. Reduce the scope for the local variables "ret" and "tmp" to one branch
of an if statement.
3. Delete the jump label "err" then.
4. Return the value from a call of the si2165_writereg8() function
without using an extra assignment for the variable "ret" at the end.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The si2165 does not support bandwidth auto-detection.
Reject the request.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Soon my dibcom.fr/parrot.com-address won't respond anymore.
Thus I'm replacing it. And, while being at it,
let's adapt some other (old) email-addresses as well.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
floppy: make local variable non-static
exynos: fixes an incorrect header guard
dt-bindings: fixes some incorrect header guards
cpufreq-dt: correct dead link in documentation
cpufreq: ARM big LITTLE: correct dead link in documentation
treewide: Fix typos in printk
Documentation: filesystem: Fix typo in fs/eventfd.c
fs/super.c: use && instead of & for warn_on condition
Documentation: fix sysfs-ptp
lib: scatterlist: fix Kconfig description
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Entities should have one or more functions. Calling it as a
type proofed to not be correct, as an entity could eventually
have more than one type.
So, rename the field as function.
Please notice that this patch doesn't extend support for
multiple function entities. Such change will happen when
we have real case drivers using it.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, media_entity_init() creates an array with the links,
allocated at init time. It provides a parameter (extra_links)
that would allocate more links than the current needs, but this
is not used by any driver.
As we want to be able to do dynamic link allocation/removal,
we'll need to change the implementation of the links. So,
before doing that, let's first remove that extra unused
parameter, in order to cleanup the interface first.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for analog and dvb tv using media controller.
Signed-off-by: Rafael Lourenço de Lima Chehab <chehabrafael@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Do not remove slave TS NULL padding PID (0x1fff) by default as
there is no real need. After that whole TS is passed to kernel sw
PID filter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is hard to debug possible I2C failures without knowing the
possible register itself. Add register number to error printing.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by kmemleak:
unreferenced object 0xffff880321e1da40 (size 32):
comm "modprobe", pid 3309, jiffies 4295019569 (age 2359.636s)
hex dump (first 32 bytes):
47 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 G...............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff82278c8e>] kmemleak_alloc+0x4e/0xb0
[<ffffffff8153c08c>] kmem_cache_alloc_trace+0x1ec/0x280
[<ffffffffa13a896a>] au8522_probe+0x19a/0xa30 [au8522_decoder]
[<ffffffff81de0032>] i2c_device_probe+0x2b2/0x490
[<ffffffff81ca7004>] driver_probe_device+0x454/0xd90
[<ffffffff81ca7c1b>] __device_attach_driver+0x17b/0x230
[<ffffffff81ca15da>] bus_for_each_drv+0x11a/0x1b0
[<ffffffff81ca6a4d>] __device_attach+0x1cd/0x2c0
[<ffffffff81ca7d43>] device_initial_probe+0x13/0x20
[<ffffffff81ca451f>] bus_probe_device+0x1af/0x250
[<ffffffff81c9e0f3>] device_add+0x943/0x13b0
[<ffffffff81c9eb7a>] device_register+0x1a/0x20
[<ffffffff81de8626>] i2c_new_device+0x5d6/0x8f0
[<ffffffffa0d88ea4>] v4l2_i2c_new_subdev_board+0x1e4/0x250 [v4l2_common]
[<ffffffffa0d88fe7>] v4l2_i2c_new_subdev+0xd7/0x110 [v4l2_common]
[<ffffffffa13b2f76>] au0828_card_analog_fe_setup+0x2e6/0x3f0 [au0828]
Checking where the error happens:
(gdb) list *au8522_probe+0x19a
0x99a is in au8522_probe (drivers/media/dvb-frontends/au8522_decoder.c:761).
756 printk(KERN_INFO "au8522_decoder attach existing instance.\n");
757 break;
758 }
759
760 demod_config = kzalloc(sizeof(struct au8522_config), GFP_KERNEL);
761 if (demod_config == NULL) {
762 if (instance == 1)
763 kfree(state);
764 return -ENOMEM;
765 }
Shows that the error path is not being handled properly.
The are actually several issues here:
1) config free should have been calling hybrid_tuner_release_state()
function, by calling au8522_release_state();
2) config is only allocated at the digital part. On the analog one,
it is received from the caller.
A complex logic could be added to address it, however, it is simpler
to just embeed config inside the state.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move timestamp from struct vb2_v4l2_buffer to struct vb2_buffer
for common use, and change its type to u64 in order to handling
y2038 problem. This patch also includes all device drivers' changes related to
this restructuring.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The queue_setup callback has a void pointer that is just for V4L2
and is the pointer to the v4l2_format struct that was passed to
VIDIOC_CREATE_BUFS. The idea was that drivers would use the information
from that struct to buffers suitable for the requested format.
After the vb2 split series this pointer is now a void pointer,
which is ugly, and the reality is that all existing drivers will
effectively just look at the sizeimage field of v4l2_format.
To make this more generic the queue_setup callback is changed:
the void pointer is dropped, instead if the *num_planes argument
is 0, then use the current format size, if it is non-zero, then
it contains the number of requested planes and the sizes array
contains the requested sizes. If either is unsupported, then return
-EINVAL, otherwise use the requested size(s).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch fix multiple spelling typos found in
various part of kernel.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.
As we're planning to drop pure http support on some
future, change all references at the media subsystem
to point to the https URL instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Without I get this error for by dvb-card:
tda10071: Unknown symbol devm_regmap_init_i2c (err 0)
cx23885_dvb_register() dvb_register failed err = -22
cx23885_dev_setup() Failed to register dvb adapters on VID_B
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It works only for HVR-4400/HVR-5500.
For WinTV-HVR-930C-HD it fails with bad/no reception
for unknown reasons.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The current si2165_set_frontend() function actually works only for DVB-T.
Split it into two functions, preparing the code to support DVB-C.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use si2165_write_reg_list() to do the DVB-T mode initialization altogether.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
si2165_set_if_freq_shift() needs to call get_if_frequency() in order to do
the right shift. Add such logic inside the function, simplifying the logic
for the callers.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TS config is fixed, so no need to write it for each tune.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Datasheet says they must be rewritten after reset.
But it only makes sense to write them when trying to tune afterwards.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is common the need of writing a table of values. Add a function to provide a
helper to address such case. This will allow further code cleanups.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is tricky to get rid of those ops here, as the stv0299 driver
wants to set frequency in separate from setting the bandwidth.
So, we use a small trick: we temporarely fill the cache with
0 for either frequency or bandwidth and add some logic at
set_params to only change the property(ies) that aren't zero.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those ops aren't used by any driver, with is weird. I suspect
that mantis_vb3030 driver were not working properly...
Anyway, now that the driver uses the set_parms, the DVB
frontend core should do the right thing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those callbacks are meant to be used only on some very specific
cases. There's absolutely no need to do that at tda8261, as
the only parameter that it allows to be set/get is the frequency.
So, use the standard get_params() and get_frequency() kABI
ops.
There's no need to touch at any bridge driver, as all interactions
are done via the macros at tda8261_cfg.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those two callbacks are the ones that should be used by normal
DVB frontend drivers.
Add support for them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On tda665x, set_state only sets frequency. As the kABI for set_state
is meant to be used only on special cases, split the function
into two, in order to allow it to be latter used by a DVBv5
cache params logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The stb6100 driver has a struct tuner_state on its state
struct, that it is used only to store the bandwidth. Even so,
this struct is not really used, as every time the bandwidth
is get or set, it goes through the hardware.
So, get rid of that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several tuner_param values that aren't by any driver or core:
DVBFE_TUNER_TUNERSTEP
DVBFE_TUNER_IFFREQ
DVBFE_TUNER_REFCLOCK
DVBFE_TUNER_IQSENSE
DVBFE_TUNER_DUMMY
Several of those correspond to the values at the tuner_state
struct with is also only initialized by not used anyware:
u32 tunerstep;
u32 ifreq;
u32 refclock;
It doesn't make sense to keep anything at the kABI that it is
not used. So, get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sR0p
-----END PGP SIGNATURE-----
Merge tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates, including:
- Lots of improvements at the kABI documentation
- Split of Videobuf2 into a common part and a V4L2 specific one
- Split of the VB2 tracing events into a separate header file
- s5p-mfc got support for Exynos 5433
- v4l2 fixes for 64-bits alignment when running 32 bits userspace
on ARM
- Added support for SDR radio transmitter at core, vivid and hackrf
drivers
- Some y2038 fixups
- Some improvements at V4L2 colorspace support
- saa7164 converted to use the V4L2 core control framework
- several new boards additions, cleanups and fixups
PS: There are two patches for scripts/kernel-doc that are needed by
the documentation patches on Media. Jon is OK on merging those via
my tree"
* tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (146 commits)
[media] c8sectpfe: Remove select on CONFIG_FW_LOADER_USER_HELPER_FALLBACK
[media] DocBook media: update copyright/version numbers
[media] ivtv: Convert to get_user_pages_unlocked()
[media] media/v4l2-ctrls: fix setting autocluster to manual with VIDIOC_S_CTRL
[media] DocBook media: Fix a typo in encoder cmd
[media] DocBook: add SDR specific info to G_MODULATOR / S_MODULATOR
[media] DocBook: add SDR specific info to G_TUNER / S_TUNER
[media] hackrf: do not set human readable name for formats
[media] hackrf: add support for transmitter
[media] hackrf: switch to single function which configures everything
[media] hackrf: add control for RF amplifier
[media] DocBook: add modulator type field
[media] v4l: add type field to v4l2_modulator struct
[media] DocBook: document SDR transmitter
[media] v4l2: add support for SDR transmitter
[media] DocBook: document tuner RF gain control
[media] v4l2: add RF gain control
[media] v4l2: rename V4L2_TUNER_ADC to V4L2_TUNER_SDR
[media] media/vivid-osd: fix info leak in ioctl
[media] media: videobuf2: Move v4l2-specific stuff to videobuf2-v4l2
...
Device stopped to tuning some channels after regmap conversion.
Reason is that regmap_update_bits() works a bit differently for
partially volatile registers than old homemade routine. Return
back to old routine in order to fix issue.
Fixes: 478932b160
Cc: <stable@kernel.org> # 4.2+
Reported-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When reading the firmware and sending commands, the length must
be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the expected
format:
si2168 11-0064: found a 'Silicon Labs Si2168-B40'
si2168 11-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 11-0064: firmware download failed -95
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffffa085708f
Add the proper check.
Cc: stable@kernel.org
Reported-by: Stuart Auchterlonie <sauchter@redhat.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If CONFIG_DVB_LNBH25 is disabled, a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function return type was wrong which caused a build error.
Fixes: e025273b86 ("[media] lnbh25: LNBH25 SEC controller driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
If CONFIG_DVB_HORUS3A is disabled a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function parameters were wrong which caused a build error.
Fixes: a5d32b3582 ("[media] horus3a: Sony Horus3A DVB-S/S2 tuner driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Replace struct v4l2_format * with void * to make queue_setup()
for common use.
And then, modify all device drivers related with this change.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix missing const in fimc-lite.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This saves a little .text and removes the sizeof(...) style
inconsistency. Use sizeof(*state) in accordance with CodingStyle.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove v4l2 stuff - v4l2_buf, v4l2_plane - from struct vb2_buffer.
Add new member variables - bytesused, length, offset, userptr, fd,
data_offset - to struct vb2_plane in order to cover all information
of v4l2_plane.
struct vb2_plane {
<snip>
unsigned int bytesused;
unsigned int length;
union {
unsigned int offset;
unsigned long userptr;
int fd;
} m;
unsigned int data_offset;
}
Replace v4l2_buf with new member variables - index, type, memory - which
are common fields for buffer management.
struct vb2_buffer {
<snip>
unsigned int index;
unsigned int type;
unsigned int memory;
unsigned int num_planes;
struct vb2_plane planes[VIDEO_MAX_PLANES];
<snip>
};
v4l2 specific fields - flags, field, timestamp, timecode,
sequence - are moved to vb2_v4l2_buffer in videobuf2-v4l2.c
struct vb2_v4l2_buffer {
struct vb2_buffer vb2_buf;
__u32 flags;
__u32 field;
struct timeval timestamp;
struct v4l2_timecode timecode;
__u32 sequence;
};
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
The dvb_frontend.c core defines a FE_ALGO_HW symbol that it is
never used. Also, both cx24123 returns 1 to get_algo() callback
instead of using DVBFE_ALGO_HW.
Probably, those are some left overs from some code cleanup.
Let's stop returning magic numbers and use the proper macro
value.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Shut up this compiler warning that I get during the daily build:
horus3a.c: In function 'horus3a_set_params':
horus3a.c:308:24: warning: 'rolloff' may be used uninitialized in this function [-Wmaybe-uninitialized]
symbol_rate * (100 + rolloff), 200000) + 5;
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert the struct dvb_pll_desc uses to const and
change the "entries" fixed array size from 12 to []
It saves a couple KB overall and remove ~5KB of data.
$ size drivers/media/dvb-frontends/dvb-pll.o*
text data bss dec hex filename
8520 1552 2120 12192 2fa0 drivers/media/dvb-frontends/dvb-pll.o.new
5624 6363 2120 14107 371b drivers/media/dvb-frontends/dvb-pll.o.old
[PG] Patch taken from https://lkml.org/lkml/2015/6/24/721 with
commit message updated.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Michael Ira Krufky <m.krufky@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The B2100A dvb NIM card from ST has 2x stv0367 demodulators
and 2x TDA18212 silicon tuners, with a 16Mhz crystal. To
get this working properly with the upstream driver we need
to add support for the 16Mhz reference clock.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When using stv0367 demodulator with STi STB platforms,
we can have easily have four or more stv0367 demods running
in the system at one time.
As typically the b2120 reference design ships with a b2004a daughter
board, which can accept two dvb NIM cards, and each b2100A NIM
has 2x stv0367 demods and 2x NXPs tuner on it.
In such circumstances it is useful to print the i2c address
on error messages to know which one is failing due to I2C issues.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
drivers/media/dvb-frontends/horus3a.c:57:19: warning: Variable length array is used.
The max usecase of the driver seems to be 10 bytes + 1 for the
register.
So, let's be safe and allocate 11 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
drivers/media/dvb-frontends/horus3a.c:57:19: warning: Variable length array is used.
The max usecase of the driver seems to be 5 bytes + 1 for the
register.
So, let's be safe and allocate 6 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
drivers/media/dvb-frontends/cxd2841er.c:205:19: warning: Variable length array is used.
The max usecase of the driver seems to be 15 bytes + 1 for the
register.
So, let's be safe and allocate 17 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/cxd2841er.c:992:5: warning: no previous prototype for 'cxd2841er_get_carrier_offset_t2' [-Wmissing-prototypes]
int cxd2841er_get_carrier_offset_t2(
^
drivers/media/dvb-frontends/cxd2841er.c:1032:5: warning: no previous prototype for 'cxd2841er_get_carrier_offset_c' [-Wmissing-prototypes]
int cxd2841er_get_carrier_offset_c(
^
drivers/media/dvb-frontends/cxd2841er.c:1360:5: warning: no previous prototype for 'cxd2841er_read_snr_t2' [-Wmissing-prototypes]
int cxd2841er_read_snr_t2(struct cxd2841er_priv *priv, u32 *snr)
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add DVB SEC frontend driver for STM LNBH25PQR chip.
[mchehab@osg.samsung.com: fix merge conflict:
fe_sec_voltage_t should not be used in kernelspace anymore.
instead, it should use enum fe_sec_voltage]
Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the DVB Frontends menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.
Without this, many drivers stay disabled during e.g. allmodconfig.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement DVBv5 CNR, signal strength, BER and block errors.
Wrap legacy DVBv3 statistics to DVBv5 internally.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a bit hack, but returning error when driver is not tuned yet
causes DVBv5 zap stop polling DVBv5 statistics. Thus return 0 even
callback is called during invalid device state.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There should be clearly some lock in order to make sure firmware
command in execution is not disturbed by another command. It has
worked as callbacks are serialized somehow pretty well and command
execution happens usually without any delays.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename device state struct from 'priv' to 'dev'.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All users are now using I2C binding and old attach could be removed.
Use I2C client for proper logging at the same.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On power-on LNB power supply voltage is disabled, due to that no
need to disable it during probe. Tone is supply is hard-coded as
external tone coming from the demodulator. Program both voltage
and tone on set_voltage(). Use register cache to prevent unneeded
programming.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As driver is now proper I2C client driver, we could use correct
functions for I2C I/O. Also rename state from priv to dev. Fix
logging too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove legacy media attach as all users are on I2C bindings now.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Even though 'compatability' has a dedicated entry in the Wiktionary,
it's listed as 'Mispelling of compatibility'. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> for the atomic_helper.c
Signed-off-by: Jiri Kosina <jkosina@suse.com>
drivers/built-in.o: In function `ts2020_read_signal_strength':
ts2020.c:(.text+0x298ff94): undefined reference to `__divdi3'
ts2020.c:(.text+0x298ffd4): undefined reference to `__divdi3'
ts2020.c:(.text+0x298fffd): undefined reference to `__divdi3'
Makefile:921: recipe for target 'vmlinux' failed
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Statistics polling can not be done by lmedm04 driver's implementation of
M88RS2000/TS2020 because I2C messages stop the device's demuxer, so allow
polling for statistics to be suppressed in the ts2020 driver by setting
dont_poll in the ts2020_config struct.
Reported-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Copy the loop_through setting from the ts2020_config struct to the internal
ts2020_priv struct so that it can actually be used.
Whilst we're at it, group the bitfields together in the same order in both
structs so that the compiler has a good chance to copy them in one go.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide a DVBv5 API signal strength. This is in units of 0.001 dBm rather
than a percentage.
>From Antti Palosaari's testing with a signal generator, it appears that the
gain calculated according to Montage's specification if negated is a
reasonable representation of the signal strength of the generator.
To this end:
(1) Polled statistic gathering needed to be implemented in the TS2020 driver.
This is done in the ts2020_stat_work() function.
(2) The calculated gain is placed as the signal strength in the
dtv_property_cache associated with the front end with the scale set to
FE_SCALE_DECIBEL.
(3) The DVBv3 format signal strength then needed to be calculated from the
signal strength stored in the dtv_property_cache rather than accessing
the value when ts2020_read_signal_strength() is called.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TS2020 and TS2022 tuners take an input from the demodulator indicating the
AGC setting on that component that is then used to influence the tuner's own
gain. This should be taken into account when calculating the gain and signal
strength.
Further, the existing TS2020 driver miscalculates the signal strength as the
result of its calculations can exceed the storage capacity of the 16-bit word
used to return it to userspace.
To this end:
(1) Add a callback function (->get_agc_pwm()) in the ts2020_config struct that
the tuner can call to get the AGC PWM value from the demodulator.
(2) Modify the TS2020 driver to calculate the gain according to Montage's
specification with the adjustment that we produce a negative value and
scale it to 0.001dB units (which is what the DVBv5 API will require):
(a) Callback to the demodulator to retrieve the AGC PWM value and then
turn that into Vagc for incorporation in the calculations. If the
callback is unset, assume a Vagc of 0.
(b) Calculate the tuner gain from a combination of Vagc and the tuner's RF
gain and baseband gain settings.
(3) Turn this into a percentage signal strength as per Montage's
specification for return to userspace with the DVBv3 API.
(4) Provide a function in the M88DS3103 demodulator driver that can be used to
get the AGC PWM value on behalf of the tuner.
(5) The ts2020_config.get_agc_pwm function should be set by the code that
stitches together the drivers for each card.
For the DVBSky cards that use the M88DS3103 with the TS2020 or the TS2022,
set the get_agc_pwm function to point to m88ds3103_get_agc_pwm.
I have tested this with a DVBSky S952 card which has an M88DS3103 and a TS2022.
Thanks to Montage for providing access to information about the workings of
these parts.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use regmap for I2C register access.
Remove own I2C repeated mutex as it should not be needed. I2C adapter
lock is already taken when I2C mux adapter is called, no need for
double locking.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename driver state from priv to dev.
Use I2C client for correct logging.
Use adapter and address from I2C client structure where needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ts2020_attach() allocates a variable pdata on the stack and then passes a
pointer to it to i2c_new_device() which stashes the pointer in persistent
structures.
Add a comment to the effect that this isn't actually an error because the
contents of the variable are only used in ts2020_probe() and this is only
called ts2020_attach()'s stack frame exists.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Register driver using I2C bindings internally when legacy media
attach is used. That is done by registering driver using I2C binding
from legacy attach. That way we can get valid I2C client, which is
needed for proper dev_() logging and regmap for example even legacy
binding is used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* We don't need calculate channel bandwidth from symbol rate as it
is calculated by DVB core.
* Use clamp() to force upper/lower limit of filter 3dB frequency.
Upper limit should never exceeded 40MHz (80MHz BW) in any case,
though...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Used frequency synthesizer is simple Integer-N PLL, with configurable
reference divider, output divider and of course N itself. Old
calculations were working fine, but not so easy to understand.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
struct timeval uses a 32-bit seconds representation which will
overflow in the year 2038 and beyond. This patch replaces
the usage of struct timeval with ktime_t which is a 64-bit
timestamp and is year 2038 safe.
This patch is part of a larger attempt to remove all instances
of 32-bit timekeeping variables (timeval, timespec, time_t)
which are not year 2038 safe, from the kernel.
[mchehab@osg.samsung.com: add a missing parenthesis, breaking compilation]
Suggested-by: Arnd Bergmann <arndb@arndb.de>
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB API was originally defined using typedefs. This is against
Kernel CodingStyle, and there's no good usage here. While we can't
remove its usage on userspace, we can avoid its usage in Kernelspace.
So, let's do it.
This patch was generated by this shell script:
for j in $(grep typedef include/uapi/linux/dvb/frontend.h |cut -d' ' -f 3); do for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f); do sed "s,${j}_t,enum $j," <$i >a && mv a $i; done; done
While here, make CodingStyle fixes on the affected lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> # for drivers/media/firewire/*
We must return -ENODEV error on case probe() fails to detect chip.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to set some error codes here.
Fixes: f01919e8f5 ('[media] m88ds3103: add I2C client binding')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/dvb-frontends/dib0090.c:1710 dib0090_dc_offset_calibration() warn: missing break? reassigning '*tune_state'
There's no need to change tune_state there, as the fall though code
will change it again to another state. So, simplify it by
removing the dead code.
While here, fix a typo:
Sart => Start
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/dvb-frontends/drxk_hard.c:3277 dvbt_sc_command() warn: missing break? reassigning 'status'
This is basically because the error handling logic there was crappy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need own I2C locking because of tuner I2C adapter/repeater.
Firmware command is executed using I2C send + reply message. Default
I2C adapter locking protects only single I2C operation, not whole
send + reply sequence as needed. Due to that, it was possible tuner
I2C message interrupts firmware command sequence.
Reported-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement I2C client device binding.
Wrap media attach to driver I2C probe.
Add wrapper from m88ds3103_attach() to m88ds3103_probe() via driver
core in order to provide proper I2C client for legacy media attach
binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use jiffies to set timeout for DiSEqC TX ready polling. Using jiffies
is more elegant solution than looping N times with sleep.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement DVBv5 BER statistics.
Wrap legacy DVBv3 BER to DVBv5 BER.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Abylay Ospan