The <dt-bindings/pinctrl/omap.h> header file defines a set of macros
for different SoCs families that falls under the OMAP sub-arch, that
allow to define the padconf register physical address instead of the
register offset from the padconf base.
But the am43xx and dra7xx SoCs families have their own pinctrl header
file so the DTS using these SoCs aren't able to use the AM4372_IOPAD()
and DRA7XX_CORE_IOPAD() macros since <dt-bindings/pinctrl/omap.h> is
not included.
Move the macros to the correct header files so can be used by the DTS.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In addition to the regular mux configuration such as mux mode 1,
2 etc, certain pins of DRA7 require to have "virtual mode" also
programmed. This allows for predefined delay characteristics to
be used by the SoC to meet timing characterstics needed for the
interface.
Provide easy to use macro to do the same.
It is important to note that the official TI guidelines recommend
to do as minimal pin reconfiguration beyond the bootloader given
the design of the hardware involved which can result in substantial
glitches which may impair functionality of certain peripherals.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For PIN_OUTPUT_PULLUP and PIN_OUTPUT_PULLDOWN we must not set the
PULL_DIS bit which disables the PULLs.
PULL_ENA is a 0 and using it in an OR operation is a NOP, so don't
use it in the PIN_OUTPUT_PULLUP/DOWN macros.
Fixes: 23d9cec07c ("pinctrl: dra: dt-bindings: Fix pull enable/disable")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DRA74/72 control module pins have a weak pull up and pull down.
This is configured by bit offset 17. if BIT(17) is 1, a pull up is
selected, else a pull down is selected.
However, this pull resisstor is applied based on BIT(16) -
PULLUDENABLE - if BIT(18) is *0*, then pull as defined in BIT(17) is
applied, else no weak pulls are applied. We defined this in reverse.
Reference: Table 18-5 (Description of the pad configuration register
bits) in Technical Reference Manual Revision (DRA74x revision Q:
SPRUHI2Q Revised June 2014 and DRA72x revision F: SPRUHP2F - Revised
June 2014)
Fixes: 6e58b8f1da ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Javier Martinez Canillas