commit f1f70479e9 "gpio: pl061: support irqdomain" drops the support of
irq generic chip and use irqdomain instead. Thus fixes the dependency by
selecting IRQ_DOMAIN rather than GENERIC_IRQ_CHIP.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et. al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL' removal,
unused uninitialised warning mitigation, error message clarity,
removal of redundant/duplicate checks, licensing (GPL -> GPL2),
coding consistency, duplicate function declaration, ret checks,
commit corrections, redundant of_match_ptr() helper removal,
spelling, #if-deffery removal and header guards name changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=PuTE
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd
Pull MFD changes from Lee Jones:
"New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
removal, unused uninitialised warning mitigation, error
message clarity, removal of redundant/duplicate checks,
licensing (GPL -> GPL2), coding consistency, duplicate
function declaration, ret checks, commit corrections,
redundant of_match_ptr() helper removal, spelling,
#if-deffery removal and header guards name changes"
* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
mfd: wm5110: Add register patch for rev D chip
mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
gpio: lp3943: Remove redundant of_match_ptr helper
mfd: sta2x11-mfd: Use named constants for pci_power_t values
Documentation: mfd: Fix LDO index in s2mps11.txt
mfd: Cleanup mfd-mcp-sa11x0.h header
mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
mfd: twl6030: Fix endianness problem in IRQ handler
mfd: sec-core: Add cells for S5M8767-clocks
mfd: max14577: Remove redundant of_match_ptr helper
mfd: twl6040: Fix sparse non static symbol warning
mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
mfd: rtsx: Fix sparse non static symbol warning
mfd: max77693: Set proper maximum register for MUIC regmap
mfd: max77686: Fix regmap resource leak on driver remove
mfd: Represent correct filenames in file headers
mfd: rtsx: Add support for card reader rtl8402
mfd: rtsx: Add set pull control macro and simplify rtl8411
mfd: max8997: Enforce mfd_add_devices() return value check
mfd: mc13xxx: Simplify probe() & remove()
...
A big set this merge window, as we have much going on in
this subsystem. Major changes this time:
- Some core improvements and cleanups to the new GPIO
descriptor API. This seems to be working now so we can
start the exodus to this API, moving gradually away from
the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move
the few GPIO ACPI clients we have to the GPIO descriptor
API right *now* before we go any further. We actually
managed to contain this *before* we started to litter
the kernel with yet another hackish global numberspace for
the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have
been migrated to use the GPIO descriptors rather than
fixed number assignments. Tegra machine has been migrated
as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x.
Those should be really good examples of how I expect a
nice GPIO driver to look these days.
- Do away with custom GPIO implementations on a major
part of the ARM machines: ks8695, lpc32xx, mv78xx0.
Make a first step towards the same in the horribly
convoluted Samsung S3C include forest. We expect to
continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em,
intel-mid and lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line
is used for IRQs and can then enforce some semantics such
as disallowing a GPIO line marked as in use for IRQ to be
switched to output mode.
- Drop all use of irq_set_chip_and_handler_name().
The name provided in these cases were just unhelpful
tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em
74x164 and msm drivers.
- Some non-urgent bug fixes here and there, duplicate
#includes and that usual kind of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lW2i
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO tree bulk changes from Linus Walleij:
"A big set this merge window, as we have much going on in this
subsystem. The changes to other subsystems (notably a slew of ARM
machines as I am doing away with their custom APIs) have all been
ACKed to the extent possible.
Major changes this time:
- Some core improvements and cleanups to the new GPIO descriptor API.
This seems to be working now so we can start the exodus to this
API, moving gradually away from the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move the few
GPIO ACPI clients we have to the GPIO descriptor API right *now*
before we go any further. We actually managed to contain this
*before* we started to litter the kernel with yet another hackish
global numberspace for the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have been
migrated to use the GPIO descriptors rather than fixed number
assignments. Tegra machine has been migrated as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x. Those
should be really good examples of how I expect a nice GPIO driver
to look these days.
- Do away with custom GPIO implementations on a major part of the ARM
machines: ks8695, lpc32xx, mv78xx0. Make a first step towards the
same in the horribly convoluted Samsung S3C include forest. We
expect to continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em, intel-mid and
lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line is used
for IRQs and can then enforce some semantics such as disallowing a
GPIO line marked as in use for IRQ to be switched to output mode.
- Drop all use of irq_set_chip_and_handler_name(). The name provided
in these cases were just unhelpful tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em 74x164 and
msm drivers.
- Some non-urgent bug fixes here and there, duplicate #includes and
that usual kind of cleanups"
Fix up broken Kconfig file manually to make this all compile.
* tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: mcp23s08: fix casting caused build warning
gpio: mcp23s08: depend on OF_GPIO
gpio: mcp23s08: Add irq functionality for i2c chips
ARM: S5P[v210|c100|64x0]: Fix build error
gpio: pxa: clamp gpio get value to [0,1]
ARM: s3c24xx: explicit dependency on <plat/gpio-cfg.h>
ARM: S3C[24|64]xx: move includes back under <mach/> scope
Documentation / ACPI: update to GPIO descriptor API
gpio / ACPI: get rid of acpi_gpio.h
gpio / ACPI: register to ACPI events automatically
mmc: sdhci-acpi: convert to use GPIO descriptor API
ARM: s3c24xx: fix build error
gpio: f7188x: set can_sleep attribute
gpio: samsung: Update documentation
gpio: samsung: Remove hardware.h inclusion
gpio: xtensa: depend on HAVE_XTENSA_GPIO32
gpio: clps711x: Enable driver compilation with COMPILE_TEST
gpio: clps711x: Use of_match_ptr()
net: rfkill: gpio: convert to descriptor-based GPIO interface
leds: s3c24xx: Fix build failure
...
This is one of LP3943 MFD driver.
LP3943 is configurable as a GPIO expander, up to 16 GPIOs.
* Application note: how to configure LP3943 as a GPIO expander
http://www.ti.com/lit/an/snva287a/snva287a.pdf
* Supported GPIO controller operations
request, free, direction_input, direction_output, get and set
* GPIO direction register not supported
LP3943 doesn't have the GPIO direction register. It only provides input and
output status registers.
So, private data for the direction should be handled manually.
This variable is updated whenever the direction is changed and
used in 'get' operation.
* Pin assignment
A driver data, 'pin_used' is checked when a GPIO is requested.
If the GPIO is already assigned, then returns as failure.
If the GPIO is available, 'pin_used' is set.
When the GPIO is not used anymore, then it is cleared.
It is defined as unsigned long type for atomic bit operation APIs,
but only LSB 16bits are used because LP3943 has 16 outputs.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MCP drivers fails to compile on trial builds due to missing
Kconfig dependency on OF_GPIO. Fix it.
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds interrupt functionality for i2c chips to the driver.
They can act as a interrupt-controller and generate interrupts, if
the inputs change.
This is tested with a mcp23017 chip on an arm based platform.
v3:
- be a bit more clear that the irq functionality is also available
on spi versions of the chips, but the linux driver does not support
this yet
v2:
- some more word about irq-mirror property in binding doc
- use of_read_bool instead of of_find_property for
"interrupt-contrller" and "irq-mirror"
- cache the "interrupt-controller" for remove function
- do set the irq-mirror bit only if device is marked as
interrupt-controller
- do create the irq mapping and setup of irq_desc of all possible
interrupts in probe path instead of in gpio_to_irq
- mark gpios as in use as interrupts in irq in irq_startup and
unlock it in irq_shutdown
- rename virq to child_irq
- remove dev argument from mcp23s08_irq_setup function
- move gpiochip_add before mcp23s08_irq_setup in probe path
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Prevent build failure when the selected variant does not support GPIO32.
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The compatible to Davinci GPIO HW block is used by other TI SoCs, like
Keystone, where GPIO support is declared as optional.
Hence, introduce GPIO_DAVINCI Kconfig option which will allow to enable
Davinci GPIO driver for Keystone SoCs when needed. At same time, kept
Davinci GPIO driver enabled for Davinci SoCs by default.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch adds support for the GPIOs found on the SMSC "Super I/
SCH311x.
The chip detection and I/O functions are copied from sch311x_wdt.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO32 is a standard optional extension to the Xtensa architecture
core that provides preconfigured output and input ports for intra
SoC signaling. The GPIO32 option is implemented as 32bit Tensilica
Instruction Extension (TIE) output state called EXPSTATE, and 32bit
input wire called IMPWIRE. This driver treats input and output
states as two distinct devices.
v3:
* Use BUG() in xtensa_impwire_set_value() to indicate that
it should never be called (Linus Walleij)
v2:
* Address the comments of Linus Walleij:
- Add a few comments
- Expand commit log message
- Use the BIT() macro for bit offsets
- Rewrite CPENABLE handling as static inlines
- Use device_initcall()
* Depend on !SMP for reason explained in the comments (Marc Gauthier)
* Use XCHAL_CP_ID_XTIOP to enable/disable GPIO32 only
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 20bc4d5d56
(gpio: 74x164: Add support for the daisy-chaining) introduce check
for DT for the driver, so driver cannot be used without DT.
There are no in-tree users of this driver, so remove non-DT support
completely.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change CONFIG_GPIO_LYNXPOINT from bool to tristate so that the
gpio-lynxpoint driver can be built as a module.
Add the required glue: an exit function to unregister the driver, and
module information.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Merged the GPIO descriptor API from Alexandre Courbot.
This is a first step toward trying to get rid of the
global GPIO numberspace for the future.
- Add an API so that driver can flag that a certain GPIO
line is being used by a irqchip backend for generating
IRQs, so that we can enforce checks, like not allowing
users to switch that line to an output at runtime, since
this makes no sense. Implemented corresponding calls
in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting
rid of a bunch of custom GPIO implementations from the
arch/arm/* tree:
- Move the IOP GPIO driver to the GPIO subsystem and
fix all users to use the gpiolib API for accessing
GPIOs. Delete the old custom GPIO implementation.
- Delete the unused custom PXA GPIO implemention.
- Convert all users of the IXP4 custom GPIO
implementation to use gpiolib and delete the custom
implementation.
- Delete the custom Gemini GPIO implementation, also
completely unused.
- Various cleanups and renamings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=881E
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"Here is the bulk of GPIO changes for the v3.13 development cycle.
I've got ACKs for the things that affect other subsystems (or it's my
own subsystem, like pinctrl). Most of that pertain to an attempt from
my side to consolidate and get rid of custom GPIO implementations in
the ARM tree. I will continue doing this.
The main change this time is the new GPIO descriptor API, background
for this can be found in Corbet's summary from this january in LWN:
http://lwn.net/Articles/533632/
Summary:
- Merged the GPIO descriptor API from Alexandre Courbot. This is a
first step toward trying to get rid of the global GPIO numberspace
for the future.
- Add an API so that driver can flag that a certain GPIO line is
being used by a irqchip backend for generating IRQs, so that we can
enforce checks, like not allowing users to switch that line to an
output at runtime, since this makes no sense. Implemented
corresponding calls in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting rid of a
bunch of custom GPIO implementations from the arch/arm/* tree:
* Move the IOP GPIO driver to the GPIO subsystem and fix all users
to use the gpiolib API for accessing GPIOs. Delete the old
custom GPIO implementation.
* Delete the unused custom PXA GPIO implemention.
* Convert all users of the IXP4 custom GPIO implementation to use
gpiolib and delete the custom implementation.
* Delete the custom Gemini GPIO implementation, also completely
unused.
- Various cleanups and renamings"
* tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: gpio-mxs: Remove unneeded dt checks
gpio: pl061: don't depend on CONFIG_ARM
gpio: bcm-kona: add missing .owner to struct gpio_chip
gpiolib: provide a declaration of seq_file in gpio/driver.h
gpiolib: include gpio/consumer.h in of_gpio.h for desc_to_gpio()
gpio: provide stubs for devres gpio functions
gpiolib: devres: add missing headers
gpiolib: make GPIO_DEVRES depend on GPIOLIB
gpiolib: devres: fix devm_gpiod_get_index()
gpiolib / ACPI: document the GPIO descriptor based interface
gpiolib / ACPI: allow passing GPIOF_ACTIVE_LOW for GpioInt resources
gpiolib / ACPI: add ACPI support for gpiod_get_index()
gpiolib / ACPI: convert to gpiod interfaces
gpiolib: add gpiod_get() and gpiod_put() functions
gpiolib: port of_ functions to use gpiod
gpiolib: export descriptor-based GPIO interface
Fixup "MAINTAINERS: GPIO-INTEL-MID: add maintainer"
gpio: bcm281xx: Don't print addresses of GPIO area in probe()
gpio: tegra: use new gpio_lock_as_irq() API
gpio: rcar: Include linux/of.h header
...
The pl061 driver has no real dependency on ARM, so remove the kconfig
dependency.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current Kconfig allows GPIO_DEVRES to be selected and compiled without
GPIOLIB. This does not make sense anymore since GPIOLIB has become the
exclusive way to deal with GPIOs. This patch makes GPIO_DEVRES available
only if GPIOLIB is selected.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO driver for the Abilis Systems TB10x series of SOCs based on ARC700
CPUs. It supports GPIO control and GPIO interrupt generation. This driver
works in conjunction with the TB10x pinctrl driver.
Signed-off-by: Sascha Leuenberger <sascha.leuenberger@abilis.com>
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio-langwell is a deprecated name. Despite the driver was made
initially for Langwell, it supports now other Intel Mid SoC's.
This patch does no change beside the file renaming with Kconfig/Makefile
update.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the IOP GPIO driver to live with its siblings in the
GPIO subsystem.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the recent code cleanup from Marek Vasut, driver gpio-ucb1400 can
be built as a module, so change symbol GPIO_UCB1400 from bool to
tristate.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the GPIO driver for the Broadcom bcm281xx family of mobile SoCs.
These GPIO controllers may contain up to 8 banks where each bank
includes 32 pins that can be driven high or low and act as an edge
sensitive interrupt.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
[Added depends on OF_GPIO]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
EMEV2 is now a DT platform, however the GPIO driver cannot be used
from a DT file since it does not fill out the of_node field in its
gpio_chip structure.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull MIPS updates from Ralf Baechle:
"This has been sitting in -next for a while with no objections and all
MIPS defconfigs except one are building fine; that one platform got
broken by another patch in your tree and I'm going to submit a patch
separately.
- a handful of fixes that didn't make 3.11
- a few bits of Octeon 3 support with more to come for a later
release
- platform enhancements for Octeon, ath79, Lantiq, Netlogic and
Ralink SOCs
- a GPIO driver for the Octeon
- some dusting off of the DECstation code
- the usual dose of cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (65 commits)
MIPS: DMA: Fix BUG due to smp_processor_id() in preemptible code
MIPS: kexec: Fix random crashes while loading crashkernel
MIPS: kdump: Skip walking indirection page for crashkernels
MIPS: DECstation HRT calibration bug fixes
MIPS: Export copy_from_user_page() (needed by lustre)
MIPS: Add driver for the built-in PCI controller of the RT3883 SoC
MIPS: DMA: For BMIPS5000 cores flush region just like non-coherent R10000
MIPS: ralink: Add support for reset-controller API
MIPS: ralink: mt7620: Add cpu-feature-override header
MIPS: ralink: mt7620: Add spi clock definition
MIPS: ralink: mt7620: Add wdt clock definition
MIPS: ralink: mt7620: Improve clock frequency detection
MIPS: ralink: mt7620: This SoC has EHCI and OHCI hosts
MIPS: ralink: mt7620: Add verbose ram info
MIPS: ralink: Probe clocksources from OF
MIPS: ralink: Add support for systick timer found on newer ralink SoC
MIPS: ralink: Add support for periodic timer irq
MIPS: Netlogic: Built-in DTB for XLP2xx SoC boards
MIPS: Netlogic: Add support for USB on XLP2xx
MIPS: Netlogic: XLP2xx update for I2C controller
...
This patch adds support for the GPIOs found on the Fintek super-I/O
chips F71882FG and F71889F.
A super-I/O is a legacy I/O controller embedded on x86 motherboards. It
is used to connect the low-bandwidth devices. Among others functions the
F71882FG/F71889F provides: a parallel port, two serial ports, a keyboard
controller, an hardware monitoring controller and some GPIO pins.
Note that this super-I/Os are embedded on some Atom-based LaCie NASes.
The GPIOs are used to control the LEDs and the hard drive power.
Changes since v3:
- Use request_muxed_region to protect the I/O ports against concurrent
accesses.
Changes since v2:
- Remove useless NULL setters for driver data.
Changes since v1:
- Enhance the commit message by describing what is a Super-I/O.
- Use self-explanatory names for the GPIO register macros.
- Add a comment to explain the platform device and driver registration.
- Fix gpio_get when GPIO is configured in input mode. I only had
the hardware to check this mode recently...
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SOCs in the OCTEON family have 16 (or in some cases 20) on-chip
GPIO pins, this driver handles them all. Configuring the pins as
interrupt sources is handled elsewhere (OCTEON's irq handling code).
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5633/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add gpio support for the on-board PLD found on some Kontron embedded modules.
Originally-from: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert gpio-tz1090 driver to use generic irqchips. This allows the
irq_ack, irq_mask, and irq_unmask callbacks and associated helper
functions to be removed. Also switch to using irq_setup_alt_chip() in
the irq_set_type callback instead of using __irq_set_handler_locked().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the low-power Powerdown Controller GPIOs in the
TZ1090 SoC.
The driver is instantiated by device tree and supports interrupts for
the SysWake GPIOs only.
Changes in v4:
- fix typos in DT bindings compatible properties
- reference Documentation/devicetree/bindings/gpio/gpio.txt in
gpio-ranges description in DT bindings
- fix gpio-ranges examples in DT bindings (it must now have 3 cells)
Changes in v3:
- separated from irq-imgpdc and removed arch/metag changes to allow
these patches to go upstream separately via the pinctrl[/gpio] trees
(particularly the pinctrl drivers depend on the new pinconf DT
bindings).
- some s/unsigned/unsigned int/.
- gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
<dt-bindings/interrupt-controller/irq.h> flags in bindings.
- gpio-tz1090*: move initcall from postcore to subsys.
Changes in v2:
- gpio-tz1090-pdc: remove references to Linux flags in dt bindings
- gpio-tz1090-pdc: make use of BIT() from linux/bitops.h
- gpio-tz1090-pdc: make register accessors inline to match pinctrl
- gpio-tz1090-pdc: update gpio-ranges to use 3 cells after recent ABI
breakage
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the main GPIOs found in the TZ1090 (Comet) SoC.
This doesn't include low-power GPIOs as they're controlled separately
via the Powerdown Controller (PDC) registers.
The driver is instantiated by device tree and supports interrupts for
all GPIOs.
Changes in v4:
- fix typos in DT bindings compatible properties
- reference Documentation/devicetree/bindings/gpio/gpio.txt in
gpio-ranges description in DT bindings
- fix gpio-ranges examples in DT bindings (it must now have 3 cells)
- gpio-tz1090: use of_property_read_u32 instead of of_get_property
Changes in v3:
- separated from irq-imgpdc and removed arch/metag changes to allow
these patches to go upstream separately via the pinctrl[/gpio] trees
(particularly the pinctrl drivers depend on the new pinconf DT
bindings).
- some s/unsigned/unsigned int/.
- some s/unsigned int/bool/ and use of BIT().
- gpio-tz1090*: refer to <dt-bindings/gpio/gpio.h> and
<dt-bindings/interrupt-controller/irq.h> flags in bindings.
- gpio-tz1090*: move initcall from postcore to subsys.
- gpio-tz1090: add REG_ prefix to some constants for consistency.
- gpio-tz1090: add comment to explain tz1090_gpio_irq_next_edge
cunningness.
Changes in v2:
- gpio-tz1090: remove references to Linux flags in dt bindings
- gpio-tz1090: make use of BIT() from linux/bitops.h
- gpio-tz1090: make register accessors inline to match pinctrl
- gpio-tz1090: update gpio-ranges to use 3 cells after recent ABI
breakage
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Incremental development for the Langwell (Atom SoC),
Xilinx, ICH and RCAR drivers.
- Cleanups from Jingoo Han, Axel Lin, Wei Jongjun,
Wolfram Sang, Tushar Behera, Sachin Kamat and Yijing Wang.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQIcBAABAgAGBQJR0T6GAAoJEEEQszewGV1zs14QAJj+NPEy5yIVUMLqBp68Wwvo
KHryjSLIDsrZj3GthRn8XG61zjdZxCuJY+i8FPldu0mIeJ1rpqxJS1DU8q0CXvuc
uJV5pBXY48WOiutspz1m3HMgNINrm2K8hgvGc3T+oSjh0+De8iacorWEPYjVZllW
ibm3rsgzamqRkI9SgXpfH5VFs9HNsxrpxgS+dRztIndWM3pEzyJQHgYm9TYEnMg8
XNWIRo54v1PRgIlW/zFMVVZvhzVc8sWjaVCp8uMnlDbyU2u/uFB632QinMyi5G7z
LaMR4AgVzC2+6Gc/7zuYSvTqTrI7Y8Dqucmz4lcsabKsoRYmdG3GZSgPRE8Eo/4b
E5t5MBb9o7juXprqMRNi68W8r9zob4UAA34KT+hkgE5dL+EDYWguX59IhQ2EkSrh
X/2OeiLi2icdBQ+yjVc0qQ07q8tAGSFX/atY3KPzvLhoxFEDdaOuI7R0r1DNT5LN
1Vps6qQVyQmsHcHO8PaPIXB76KuOQ7W4oYfma/JjxOjZtjcGJdyG+/0UkdsSobET
l4Q+2WxlozNoN6zsHeJd2iPc6LB61ZCG3BzsCbv/tVPEJ8fsMylC1pAAEoaNZ6zf
0HzTFWa2ZiBe7F95m2leQmtHlvZ2oME+IkS3xUY8v0VQD77bdKWXs63c91JUHLC9
BywEJzCgXvUoR6O+mr4p
=5JfC
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is a batch of GPIO changes for v3.11. I have agreed with Grant
to take care of the pull requests for this development cycle.
No special things are happening in the GPIO tree this time (nice with
some calm) and I have been extra careful to do regression builds and
it's well boiled in -next.
GPIO changes for the v3.11 development cycle:
- Incremental development for the Langwell (Atom SoC), Xilinx, ICH
and RCAR drivers.
- Cleanups from Jingoo Han, Axel Lin, Wei Jongjun, Wolfram Sang,
Tushar Behera, Sachin Kamat and Yijing Wang"
* tag 'gpio-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (35 commits)
Gpio/trivial: replace numeric with standard PM state macros
gpiolib: remove warnning of allocations with IRQs disabled
gpio: grgpio: Staticize local symbols
gpio-langwell: remove Withney point support
gpio: ich: add GPO_BLINK support
gpio-sta2x11: Convert to use devm_ioremap_resource
gpio_msm: Convert to use devm_ioremap_resource
gpio-rcar: Use OUTDT when reading GPIOs configured as output
gpio-sta2x11: Fix potential NULL pointer dereference
gpio/omap: omap_gpio_init_context stub must be inline
gpio: msm-v1: Remove errant __devinit to fix compile
gpio: devres: make comments proper
GPIO: xilinx: Enable driver for Xilinx zynq
DT: Add documentation for gpio-xilinx
GPIO: xilinx: Use BIT macro
GPIO: xilinx: Use __raw_readl/__raw_writel IO functions
GPIO: xilinx: Add support for dual channel
GPIO: xilinx: Simplify driver probe function
gpio: sx150x: convert to use devm_* functions
MAINTAINERS: add linux-gpio mailing list
...
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
- remove board file for exynos
- remove legacy files which are not used anymore
- decouple ARCH_EXYNOS from PLAT_S5P
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SHg+
-----END PGP SIGNATURE-----
Merge tag 'remove-nondt-exynos-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
From Kukjin Kim:
cleanup and removing dead code for only support DT for exynos
- remove board file for exynos
- remove legacy files which are not used anymore
- decouple ARCH_EXYNOS from PLAT_S5P
* tag 'remove-nondt-exynos-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (35 commits)
ARM: EXYNOS: Remove remaining dead code after non-DT support removal
ARM: EXYNOS: Remove legacy L2X0 initialization
ARM: EXYNOS: Use exynos_init_io() as map_io callback
ARM: EXYNOS: Remove custom init_irq callbacks
ARM: EXYNOS: Remove mach/regs-usb-phy.h header
thermal: exynos: Support both EXYNOS4X12 SoCs
ARM: EXYNOS: Remove unused base addresses from mach/map.h header
ARM: EXYNOS: Remove mach/irqs.h header
ARM: EXYNOS: Select SPARSE_IRQ for Exynos
ARM: SAMSUNG: Make legacy MFC support code depend on SAMSUNG_ATAGS
ARM: EXYNOS: Remove mach/regs-gpio.h header
ARM: EXYNOS: Remove mach/gpio.h
ARM: EXYNOS: Remove setup-i2c0.c
ARM: EXYNOS: Do not select legacy Kconfig symbols any more
ARM: SAMSUNG: Include most of mach/ headers conditionally
ARM: EXYNOS: Decouple ARCH_EXYNOS from PLAT_S5P
USB: Check for ARCH_EXYNOS separately
platform: Check for ARCH_EXYNOS separately
ARM: SAMSUNG: Compile legacy IRQ and GPIO PM code only with ATAGS support
ARM: EXYNOS: Provide compatibility stubs for PM code in pm-core.h header
...
Conflicts:
arch/arm/mach-exynos/Kconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds Kconfig entry that selects whether legacy Samsung GPIO
driver should be built or not. For platforms that support only DT based
boot, the new pinctrl driver is used and so the old one is not needed.
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Enable gpio driver for usage on Xilinx ARM zynq platform.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are a handful of cleanups to the MSM tree. The gpio cleanups
get us closer to having proper pinmux and gpio support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=9wS3
-----END PGP SIGNATURE-----
Merge tag 'msm-cleanup-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From David Brown:
Cleanups for MSM for 3.11
These are a handful of cleanups to the MSM tree. The gpio cleanups
get us closer to having proper pinmux and gpio support.
* tag 'msm-cleanup-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
mfd: ssbi: Use devm_* and simplify code
gpio: msm: Add device tree and irqdomain support for gpio-msm-v2
ARM: msm: Remove gpiomux-v2 and re-organize MSM_GPIOMUX configs
msm: iomap: Remove unused bases and mappings
msm: Remove unused file core.h
ARM: msm: Remove init_irq declaration in machine description
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/boot/dts/msm8660-surf.dts
arch/arm/boot/dts/msm8960-cdp.dts
This cleans up the gpio-msm-v2 driver of all the global define usage.
The number of gpios are now defined in the device tree. This enables
adding irqdomain support as well.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
max7301 is controlled through SPI interface which means another driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes below build error when CONFIG_SPI_MASTER=y && CONFIG_I2C=m &&
CONFIG_GPIO_MCP23S08=y.
LD init/built-in.o
drivers/built-in.o: In function `mcp23017_write':
clkdev.c:(.text+0x1e14): undefined reference to `i2c_smbus_write_word_data'
drivers/built-in.o: In function `mcp23017_read':
clkdev.c:(.text+0x1e24): undefined reference to `i2c_smbus_read_word_data'
drivers/built-in.o: In function `mcp23008_write':
clkdev.c:(.text+0x1e8c): undefined reference to `i2c_smbus_write_byte_data'
drivers/built-in.o: In function `mcp23008_read':
clkdev.c:(.text+0x1e98): undefined reference to `i2c_smbus_read_byte_data'
drivers/built-in.o: In function `mcp23008_read_regs':
clkdev.c:(.text+0x1ed0): undefined reference to `i2c_smbus_read_byte_data'
drivers/built-in.o: In function `mcp23s08_init':
clkdev.c:(.init.text+0x30): undefined reference to `i2c_register_driver'
drivers/built-in.o: In function `mcp23s08_exit':
clkdev.c:(.exit.text+0x30): undefined reference to `i2c_del_driver'
make: *** [vmlinux] Error 1
When CONFIG_I2C=m, meaning we can't build the drivers in with I2C support.
Thus don't allow the drivers to be compiled as built-in when CONFIG_I2C=m.
The real fix though is to break the driver apart into a SPI part, an I2C part
and a common part. But that's something for 3.11 while this is something for
3.10/stable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using the
common clock subsystem). The latter will have to get converted in one
of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot of
infrastructure in shmobile that has not been converted to DT yet. Once
those are resolved to the degree that no board specific setup code is
needed, they can get folded into the respective SoC setup files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xaLf
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates (part 2) from Arnd Bergmann:
"These patches are all for Renesas shmobile, and depend on the earlier
pinctrl updates. Remarkably, this adds support for three new SoCs:
r8a73a4, r8a73a4 and r8a7778. The bulk of the code added for these is
for pinctrl (using the new subsystem) and for clocks (not yet using
the common clock subsystem). The latter will have to get converted in
one of the upcoming releases, but shmobile is not ready for that yet.
The series also contains Renesas shmobile board changes, adding one
board file for each of the three new SoCs. These boards are using a
mix of classic and device-tree based probing, as there is still a lot
of infrastructure in shmobile that has not been converted to DT yet.
Once those are resolved to the degree that no board specific setup
code is needed, they can get folded into the respective SoC setup files."
* tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: shmobile: use r8a7790 timer setup code on Lager
ARM: shmobile: force enable of r8a7790 arch timer
ARM: shmobile: Add second I/O range for r8a7790 PFC
ARM: shmobile: bockw: enable network settings on bootargs
ARM: shmobile: bockw: add SMSC ethernet support
ARM: shmobile: R8A7778: add Ether support
ARM: shmobile: bockw: enable SMSC ethernet on defconfig
ARM: shmobile: r8a7778: add r8a7778_init_irq_extpin()
ARM: shmobile: r8a7778: remove pointless PLATFORM_INFO()
ARM: shmobile: mackerel: clean up MMCIF vs. SDHI1 selection
ARM: shmobile: mackerel: add interrupt names for SDHI0
ARM: shmobile: mackerel: switch SDHI and MMCIF interfaces to slot-gpio
ARM: shmobile: mackerel: remove OCR masks, where regulators are used
ARM: shmobile: mackerel: SDHI resources do not have to be numbered
ARM: shmobile: Initial r8a7790 Lager board support
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
ARM: shmobile: APE6EVM base support
ARM: shmobile: kzm9g-reference: add ethernet support
ARM: shmobile: add R-Car M1A Bock-W platform support
...
The usual selection of bug fixes and driver updates for GPIO. Nothing
really stands out except the addition of the GRGPIO driver and some
enhacements to ACPI support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRhuKVAAoJEEFnBt12D9kB8kUP/21N7fsCxNocqoIwX8VQPfEY
KsXUKRstuETHERHpGCSvMuRAEy1vee9itijrmWOiQT09jztIxg3Sed3u0RCQjQEK
mV87RdAObZzm6xTIpy5sQa1bMOlc2AzYhTDDr9f1OpU+L9XMhwq03wq/i74Zij3w
7vq5BkBfGWF84TY5ZG1SNIvtw9P2MYoCHtJKvFyTJWAH05m2bHSfuvvn8vIdcUBL
TuVwoeUzbYJtTJatovkh0kyMOOZEh9JVWBPBTNNLyYDmpAKQ6RwBoAi0ZznmF4mk
gp88dj6iMHebi7UnlDQJD5crw16cRoMh0pa3EBAjYM0IVhfn8AvFIhma34wTs1Z/
ZuWwwHeR93cQTKwMBT1OHRCPaOdjS5riAR4WJm5Tmq9dV0sjGlbwff26U1uHH8qX
mTBA+tje4bVpSHEztmXyw0AOMUv2vid5P0F/sKtEHzfURf8Yjq8xvxyvq14T3dQQ
/wzmdLKbzR05phft7Xxa4yzfSy46uvxyUJQQaKdU/jlay/gJFisJXJE0cOrwTOFo
SpTCmjnacr8Tlqr04Fj8f8ZgOYrg5VAOUsVE8uY0ETWRCb7iezFw7JGE3qV1kZQk
N1lPBbSnIwtkdMiEmyttxpFEb5PwJxX8pUP6JfNyMbMlHoZs2247SeakhRQs/OCx
goJQEGz6eeOpvq7koiJg
=PwUd
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull GPIO changes from Grant Likely:
"The usual selection of bug fixes and driver updates for GPIO. Nothing
really stands out except the addition of the GRGPIO driver and some
enhacements to ACPI support"
I'm pulling this despite the earlier mess. Let's hope it compiles these
days.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: (46 commits)
gpio: grgpio: Add irq support
gpio: grgpio: Add device driver for GRGPIO cores
gpiolib-acpi: introduce acpi_get_gpio_by_index() helper
GPIO: gpio-generic: remove kfree() from bgpio_remove call
gpio / ACPI: Handle ACPI events in accordance with the spec
gpio: lpc32xx: Fix off-by-one valid range checking for bank
gpio: mcp23s08: convert driver to DT
gpio/omap: force restore if context loss is not detectable
gpio/omap: optimise interrupt service routine
gpio/omap: remove extra context restores in *_runtime_resume()
gpio/omap: free irq domain in probe() failure paths
gpio: gpio-generic: Add 16 and 32 bit big endian byte order support
gpio: samsung: Add terminating entry for exynos_pinctrl_ids
gpio: mvebu: add dbg_show function
MAX7301 GPIO: Do not force SPI speed when using OF Platform
gpio: gpio-tps65910.c: fix checkpatch error
gpio: gpio-timberdale.c: fix checkpatch error
gpio: gpio-tc3589x.c: fix checkpatch errors
gpio: gpio-stp-xway.c: fix checkpatch error
gpio: gpio-sch.c: fix checkpatch error
...
This driver supports GRGPIO gpio cores available in the GRLIB VHDL IP
core library from Aeroflex Gaisler.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GENERIC_GPIO has been made equivalent to GPIOLIB in architecture code
and all driver code has been switch to depend on GPIOLIB. It is thus
safe to have GENERIC_GPIO removed.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
With the move to a combined pinctrl/gpio driver, the arch-vt8500
gpio driver is no longer required.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch is V3 of a GPIO driver for the R-Car series of
SoCs from Renesas. This driver is designed to be reusable
between multiple SoCs that share the same basic building block,
but so far it has only been used on R-Car H1 (r8a7779).
Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on a single I/O memory
range and the 32 GPIOs are hooked up a single interrupt.
In the case of R-Car H1 either external IRQ pins or GPIOs
with interrupts can be used for on-board interupts. For
external IRQs 4 pins are supported, and in the case of GPIO
there are 202 GPIOS as 202 interrupts hooked up via 6 driver
instances and to the GIC and the Cortex-A9 Quad.
At this point this driver is interfacing as a regular
platform device driver. In the future DT support will be
submitted as an incremental feature patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Axel Lin