This patch separates the platform devices registration for the MTX-1
specific devices: GPIO leds and watchdog.
[Minor fixup and formatting change -- Ralf]
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mmap with MAP_FIXED was not validating the addr and len parameters. This
leads to the failure of GCC's gcc.c-torture/execute/loop-2[fg].c testcases
when using the o32 ABI on a 64 bit kernel.
These testcases try to mmap 65536 bytes at 0x7fff8000 and then access all
the memory. In 2.6.18 and 2.6.23.1 (and likely other versions as well)
the kernel maps the requested memory, but since half of it is above
0x80000000 a SIGBUS is generated when it is accessed.
This patch moves the len validation above the MAP_FIXED processing so that
it is always validated. It also adds validation to the addr parameter for
MAP_FIXED mappings.
Signed-off-by: David Daney <ddaney@avtrex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Try increasingly longer time periods starting of at 0x10 cycles. This
should be fast on hardware and work nicely with emulators.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The expression "(long)(read_c0_count() - cnt)" can never be a negative
value on 64-bit kernel. Cast to "int" before comparison.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
They break the timer interrupt initialization and only seem to be a kludge
for initialization happening in the wrong order. Further testing done by
Thiemo confirms the suspicion that the other invocations also seem to have
useless.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert jmr3927_clock_event_device to more generic
txx9tmr_clock_event_device which supports one-shot mode. The
txx9tmr_clock_event_device can be used for TX49 too if the cp0 timer
interrupt was not available.
Convert jmr3927_hpt_read to txx9_clocksource driver which does not
depends jiffies anymore. The txx9_clocksource itself can be used for
TX49, but normally TX49 uses higher precision clocksource_mips.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixme: At the time of this writing cevt-r4k.c doesn't yet know about how
to handle the alternate timer interrupt of the RM9000.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since the cp0 compare interrupt handler isn't initialized by the time
plat_time_init is called don't set IE_IRQ5 anymore, cevt-r4k.c will do
that a little later itself.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The old plat_timer_setup hook is no longer getting called so the Alchemy
time initialization was getting skipped.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
clockevent_delta2ns() use the shift and mult value, so
clockevent_set_clock() should be called first.
Pointed out by Atsushi Nemoto.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
set_next_event() and set_mode() are always called with interrupt disabled.
irqsave and irqrestore are not necessary for spinlock.
Pointed out by Atsushi Nemoto.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Modify the SMTC initialization code to allow boot-time specification not
only of how many VPEs and TCs to use, but also how many TCs out of the
allowed pool are to be bound to VPE 0. The new boot option is "vpe0tcs=N",
where N is an integer. Using it in combination with the existing options
allows arbitrary assignments across the 2 VPEs of a 34K. e.g. "maxtcs=3
vpe0tcs=1" forces VPE0 to have 1 TC, while VPE1 has 2, and "maxtcs=4
vpe0tcs=3" forces VPE0 to have 3 TCs, while VPE1 gets 1. If no vpe0tcs
option is specified, the traditional algorithm of evenly dividing TCs
between available VPEs, with the odd "slop" going to VPE0, is retained.
The reason for doing this is to allow a finer balancing of TCs which can
handle I/O interrupts on Malta (those on VPE 0) and those which cannot.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update sn2_defconfig to select 64KB page size, as well as include new
config options.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Clean up the process for presenting the "physical id" field in
/proc/cpuinfo.
- remove global smp_num_cpucores, as it is mostly useless
- remove check_for_logical_procs(), since we do the same
functionality in identify_siblings()
- reflow logic in identify_siblings(). If an older CPU
does not implement PAL_LOGICAL_TO_PHYSICAL, we may still
be able to get useful information from SAL_PHYSICAL_ID_INFO
- in identify_siblings(), threads/cores are a property of
the CPU, not the platform
- remove useless printk's about multi-core / thread
capability in identify_siblings(), as that information
is readily available in /proc/cpuinfo, and printing for
the BSP only adds little value
- smp_num_siblings is now meaningful if any CPU in the
system supports threads, not just the BSP
- expose "physical id" field, even on CPUs that are not
multi-core / multi-threaded (as long as we have a valid
value). Now we know what sockets Madisons live in too.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When gcc uses --build-id by default, the gate.lds.S linker script runs afoul
of the new note section and produces a bad DSO image. This fixes it.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some versions of ld with --build-id support will crash when using the flag
with a linker script that discards notes. This bites ia64's check-segrel.lds.
The bug is easy to avoid.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
vmcore_find_descriptor_size() is only called by
reserve_elfcorehdr(), which is in __init, so it seems to me that
vmcore_find_descriptor_size() should be there too.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes the following section mismatches:
<-- snip -->
...
WARNING: vmlinux.o(.text+0x5b5c2): Section mismatch: reference to .init.text:memmap_init_zone (between 'memmap_init' and 'virtual_memmap_init')
WARNING: vmlinux.o(.text+0x5b842): Section mismatch: reference to .init.text:memmap_init_zone (between 'virtual_memmap_init' and 'ia64_mmu_init')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'sg' of git://git.kernel.dk/linux-2.6-block:
Correction of "Update drivers to use sg helpers" patch for IMXMMC driver
sg_init_table() should use unsigned loop index variable
sg_last() should use unsigned loop index variable
Initialise scatter/gather list in sg driver
Initialise scatter/gather list in ata_sg_setup
x86: fix pci-gart failure handling
SG: s390-scsi: missing size parameter in zfcp_address_to_sg()
SG: clear termination bit in sg_chain()
Don't undef __i386__/__x86_64__ in uml anymore, make sure that (few) places
that required adjusting the ifdefs got those.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is fixes a problem where we could jump to the wrong address. By
doing a "p0 = reti; jump (p0)". If a different, higher level interrupt
came in, just before, rather than returning to the calling function, we
would return to a random place in the kernel.
This very elegant fix from Bernd grabs the return location off the
stack, and places it into P0, so when we do a return, it goes to the
correct place.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- move the CONFIG_KGDB into one block, for easier reading
- remove printk from printk_address, and pass around buffers. Also
print out the labels when decoding CPLB errors, so you know exactly
where the error was.
- Do not use fixed addresses, becuase people do not know where they come from.
- Turn the printing level down on the dump, so if you don't want,
only the signal prints out - just like on other archs. If a kernel/interrupt
crashes, it should dump everything all the time
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
This fixes two things:
- stop calling write_lock_irq/write_unlock_irq which can turn modify
irq levels
- don't calling mmput when handing exceptions - since this might_sleep,
which does a rti, and leaves us in kernel space (irq15, rather
than irq5).
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
blk_rq_map_sg doesn't initialize sg->dma_address/length to zero
anymore. Some low level drivers reuse sg lists without initializing so
IOMMUs might get non-zero dma_address/length. If map_sg fails, we need
pass the number of the mapped entries to gart_unmap_sg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds the symbol "init_level4_pgt" to the vmcoreinfo data so
that makedumpfile (dump filtering command) supports x86_64 sparsemem
kernel of linux-2.6.24.
makedumpfile creates a small dumpfile by excluding unnecessary pages for
the analysis. It checks attributes in page structures and distinguishes
necessary pages and unnecessary ones. To check them, makedumpfile gets
the vmcoreinfo data which has the minimum debugging information only for
dump filtering.
For older x86_64 kernel (linux-2.6.23 or before), makedumpfile translates
the virtual address of page structure into physical address by subtracting
PAGE_OFFSET from virtual address, but this translation isn't effective for
linux-2.6.24 sparsemem kernel, because its page structures are in virtual
memmap area. makedumpfile should translate their virtual address by 4-levels
paging and it needs the symbol "init_level4_pgt".
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
fix this warning:
arch/x86/kernel/early-quirks.c:40: warning: nvidia_hpet_check defined but not used
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix !CONFIG_SMP warning:
arch/x86/kernel/acpi/processor.c: In function arch_acpi_processor_init_pdc:
arch/x86/kernel/acpi/processor.c:65: warning: unused variable cpu
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The kernel only ever supports 1 version of the boot protocol
so there is no need to check the boot protocol revision to
see if a feature is supported.
Both x86 and x86_64 support the same boot protocol so we need
to implement the KEEP_SEGMENTS on x86_64 as well. It isn't
just paravirt bootloaders that could use this functionality.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Andi Kleen <ak@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There were two problems. Firstly, someone forgot the struct keyword in
front of cpuinfo_x86, so I take it this wasn't even compile checked.
Secondly, the actual definition has this as a SHARED_ALIGNED, so the
definitions mismatch.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
KVM uses smp_call_function_mask and therefor need smp_ops to be exported.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 6442eea937.
The patch breaks smp_ops and needs to be reverted. The solution to
allow modular build of KVM is to export smp_ops instead.
Pointed-out-by: James Bottomley
<jejb> tglx, so write out 100 times "voyager is a useful architecture" ...
<tglx> yes, Sir
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
x86 setup: sizeof() is unsigned, unbreak comparisons
x86 setup: handle boot loaders which set up the stack incorrectly
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/x86:
x86: kill the old i386 and x86_64 directories
x86: move i386 and x86_64 Kconfig files to x86 directory
kconfig: small code refactoring in kconfig Makefile
x86: unification of i386 and x86_64 Kconfig.debug
x86: move defconfig files for i386 and x86_64 to x86
x86: move i386 and x86_64 Makefiles to arch/x86
We use signed values for limit checking since the values can go
negative under certain circumstances. However, sizeof() is unsigned
and forces the comparison to be unsigned, so move the comparison into
the heap_free() macros so we can ensure it is a signed comparison.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Apparently some specific versions of LILO enter the kernel with a
stack pointer that doesn't match the rest of the segments. Make our
best attempt at untangling the resulting mess.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'sg' of git://git.kernel.dk/linux-2.6-block:
fix sg_phys to use dma_addr_t
ub: add sg_init_table for sense and read capacity commands
x86: pci-gart fix
blackfin: fix sg fallout
xtensa: dma-mapping.h is using linux/scatterlist.h functions, so include it
SG: audit of drivers that use blk_rq_map_sg()
arch/um/drivers/ubd_kern.c: fix a building error
SG: Change sg_set_page() to take length and offset argument
AVR32: Fix sg_page breakage
mmc: sg fallout
m68k: sg fallout
More SG build fixes
sg: add missing sg_init_table calls to zfcp
SG build fix
Adding proper dependencies so the two Kconfig.debug files
are now identical and move the result file to x86.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
With some small changes to kconfig makefile we can now
locate the defconfig files for i386 and x86_64 in
the configs/ subdirectory under x86.
make ARCH=i386 defconfig and make defconfig
works as expected also after this change.
But arch maintainers shall now update a defconfig file in
the configs/ directory.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Moving the ARCH specific Makefiles for i386 and x86_64
required a litle bit tweaking in the top-lvel Makefile.
SRCARCH is now set in the top-level Makefile
because we need this info to include the correct
arch Makefile.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Ensure we fixup the IRQ state before we hit any locking code.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
map_sg could copy the last sg element to another position (if merging
some elements). It breaks sg chaining. This copies only
dma_address/length instead of the whole sg element.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Went through the documentation doing typo and content fixes. This
patch contains only comment and whitespace changes.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix this error (i386 !SMP build)
arch/x86/lguest/boot.c: In function ‘lguest_init’:
arch/x86/lguest/boot.c:1059: error: ‘pm_power_off’ undeclared (first use in this function)
by including linux/pm.h.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix this uml building error:
arch/um/drivers/ubd_kern.c: In function 'do_ubd_request':
arch/um/drivers/ubd_kern.c:1118: error: implicit declaration of function
'sg_page'
arch/um/drivers/ubd_kern.c:1118: warning: passing argument 6 of
'prepare_request' makes pointer from integer without a cast
make[1]: *** [arch/um/drivers/ubd_kern.o] Error 1
make: *** [arch/um/drivers] Error 2
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Add sg_init_table() call as well.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix this error (i386 !SMP build):
arch/x86/lguest/boot.c: In function lguest_init:
arch/x86/lguest/boot.c:1059: error: pm_power_off undeclared (first use in this function)
by including linux/pm.h.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Looks like the MAP_FIXED case is using the wrong address hint. I'd
expect the comment "don't mess with it" means pass the request
straight on through, not change the address requested to -ENOMEM.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark the m68knommu setup_arch() function as __init.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removed header includes not needed.
Remove use of old m68knommu timer function pointers.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up 68EZ328 timer support code. Removed header includes not needed.
Remove use of old m68knommu timer function pointers.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up 68360 timer support code. Removed header includes not needed.
Remove use of old m68knommu timer function pointers. Use common function
naming for 68328 timer functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use common function naming for 68328 timer functions to make them
consistent with the various other hardware m68knommu timers.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up 68328 timer support code. Removed header includes not needed.
Remove use of old m68knommu timer function pointers.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'irq-upstream' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
[SPARC, XEN, NET/CXGB3] use irq_handler_t where appropriate
drivers/char/riscom8: clean up irq handling
isdn/sc: irq handler clean
isdn/act2000: fix major bug. clean irq handler.
char/pcmcia/synclink_cs: trim trailing whitespace
drivers/char/ip2: separate polling and irq-driven work entry points
drivers/char/ip2: split out irq core logic into separate function
[NETDRVR] lib82596, netxen: delete pointless tests from irq handler
Eliminate pointless casts from void* in a few driver irq handlers.
[PARPORT] Remove unused 'irq' argument from parport irq functions
[PARPORT] Kill useful 'irq' arg from parport_{generic_irq,ieee1284_interrupt}
[PARPORT] Consolidate code copies into a single generic irq handler
Rather than hand-rolling our own prototype, make the code more
future-proof by using the standard irq_handler_t typedef.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4630/1: Fix the vector stride of the double vector instruction.
[ARM] 4629/1: Fix VFP emulation code to clear all exception flags of FPEXC
[ARM] 4613/1: pxa300: MFP typo fix
Add support to force_hpet for all known MCP55 (nForce 5) chipset
LPC bridges.
These are the untested nForce 5 chips (taken from Mikko's original
patch, and checked against pci.ids).
Signed-off-by: Carlos Corbacho <cathectic@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/quirks.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
This patch adds a quirk from LinuxBIOS to force enable HPET on
the nVidia CK804 (nForce 4) chipset.
This quirk can very likely support more than just nForce 4
(LinuxBIOS use the same code for nForce 5), and possibly nForce 3,
but I don't have those chipsets, so cannot add and test them.
Tested on an Abit KN9 (CK804).
Signed-off-by: Carlos Corbacho <cathectic@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Documentation/kernel-parameters.txt | 3 +-
arch/x86/kernel/quirks.c | 37 +++++++++++++++++++++++++++++++++++-
2 files changed, 38 insertions(+), 2 deletions(-)
Make <asm/setup.h> usable by the boot code.
Clean up vestiges of the old command-line protocol from setup.h and
head_32.S (it is still supported from the boot loader point of
view, since it is converted to the new command-line protocol by the
boot code.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
During hibernation and suspend on x86_64 save CPU registers in the saved_context
structure rather than in a handful of separate variables.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The x86_64 arch/x86/kernel/Makefile uses references into
arch/x86/kernel/cpu/... to use code from there.
Unifiy it with the nicely structured i386 way and reuse the existing
subdirectory make rules.
Also move the machine check related source into ...kernel/cpu/mcheck,
where the other machine check related code is.
No code change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move mce.c to mce_32.c to allow the later move of the x86_64 mce.c
from arch/x86/kernel/ to ...kernel/cpu/mcheck
No code change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Prepare the makefiles in x86/kernel/cpu and x86/kernel/cpu/mcheck to
be used by the x86_64 build as well.
No code change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Preperatory patch to simplify the sharing of Makefiles in
arch/x86.
Linus came up with this during a discussion about the ugliness of
ifeq($CONFIG_X86_32),y) and obj-$(CONFIG_X86_32) in the shared
Makefiles.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Most of contents in crash are same.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The previous patch wasn't correctly handling the 'count' variable. If
a CPU gave bad results on the 1st or 2nd run but good results on the
3rd, it wouldn't do the correct thing. No idea if any such CPU
exists, but the patch below handles that case by discarding the bad
runs.
If a bad result (too quick, or too slow) occurs on any of the 3 runs
it will be discarded.
Also updated some comments to explain what's going on.
Signed-off-by: Dave Johnson <djohnson@sw.starentnetworks.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I ran into this problem on a system that was unable to obtain NTP sync
because the clock was running very slow (over 10000ppm slow). ntpd had
declared all of its peers 'reject' with 'peer_dist' reason.
On investigation, the tsc_khz variable was significantly incorrect
causing xtime to run slow. After a reboot tsc_khz was correct so I
did a reboot test to see how often the problem occurred:
Test was done on a 2000 Mhz Xeon system. Of 689 reboots, 8 of them
had unacceptable tsc_khz values (>500ppm):
range of tsc_khz # of boots % of boots
---------------- ---------- ----------
< 1999750 0 0.000%
1999750 - 1999800 21 3.048%
1999800 - 1999850 166 24.128%
1999850 - 1999900 241 35.029%
1999900 - 1999950 211 30.669%
1999950 - 2000000 42 6.105%
2000000 - 2000000 0 0.000%
2000050 - 2000100 0 0.000%
[...]
2000100 - 2015000 1 0.145% << BAD
2015000 - 2030000 6 0.872% << BAD
2030000 - 2045000 1 0.145% << BAD
2045000 < 0 0.000%
The worst boot was 2032.577 Mhz, over 1.5% off!
It appears that on rare occasions, mach_countup() is taking longer to
complete than necessary.
I suspect that this is caused by the CPU taking a periodic SMI
interrupt right at the end of the 30ms calibration loop. This would
cause the loop to delay while the SMI BIOS hander runs. The resulting
TSC value is beyond what it actually should be resulting in a higher
tsc_khz.
The below patch makes native_calculate_cpu_khz() take the best
(shortest duration, lowest khz) run of it's 3 calibration loops. If a
SMI goes off causing a bad result (long duration, higher khz) it will
be discarded.
With the patch applied, 300 boots of the same system produce good
results:
range of tsc_khz # of boots % of boots
---------------- ---------- ----------
< 1999750 0 0.000%
1999750 - 1999800 30 10.000%
1999800 - 1999850 166 55.333%
1999850 - 1999900 89 29.667%
1999900 - 1999950 15 5.000%
1999950 < 0 0.000%
Problem was found and tested against 2.6.18. Patch is against 2.6.22.
Signed-off-by: Dave Johnson <djohnson@sw.starentnetworks.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It seems commit 09cadedbdc was incomplete
due to a clash with the x86 architecture merge.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest: (45 commits)
Use "struct boot_params" in example launcher
Loading bzImage directly.
Revert lguest magic and use hook in head.S
Update lguest documentation to reflect the new virtual block device name.
generalize lgread_u32/lgwrite_u32.
Example launcher handle guests not being ready for input
Update example launcher for virtio
Lguest support for Virtio
Remove old lguest I/O infrrasructure.
Remove old lguest bus and drivers.
Virtio helper routines for a descriptor ringbuffer implementation
Module autoprobing support for virtio drivers.
Virtio console driver
Block driver using virtio.
Net driver using virtio
Virtio interface
Boot with virtual == physical to get closer to native Linux.
Allow guest to specify syscall vector to use.
Rename "cr3" to "gpgdir" to avoid x86-specific naming.
Pagetables to use normal kernel types
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Add Vitaly Bordug as PPC8xx maintainer
[POWERPC] 4xx: Enable EMAC on Bamboo board
[POWERPC] 4xx: Enable EMAC for PPC405 Walnut board
[POWERPC] 4xx: Fix timebase clock selection on Walnut
[POWERPC] 4xx: Enable EMAC on the PPC 440GP Ebony board
[POWERPC] 4xx: Split early debug output and early boot console for 44x
[POWERPC] 4xx: Enable NEW EMAC support for Sequoia 440EPx.
[POWERPC] 4xx: Add RGMII support for Sequoia 440EPx
Reduce the function pointer mess of the m68knommu timer code by calling
directly to the local hardware's timer setup, and expose the local
common timer interrupt handler to the lower level hardware timer.
Ultimately this will save definitions of all these functions across all
the platform code to setup the function pointers (which for any given
m68knommu CPU family member can be only one set of hardware timer
functions).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix system call restart handling. We can call directly to the
restart handler, no need to back track through trap that isn't
even implemented on m68knommu.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add make support for the Savant/Rosie1 board.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no separate stack region addresses to print at startup time,
so remove it from the debug listing
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for the Savant/Rosie1 board.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Updated defconfig with new options for m68knommu.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the system call code for handling syscall tracing, so strace
and gdbserver work properly.
This fix originally developed by Philippe De Muyter and Stuart Hughes.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zero out dma_length in the entry immediately following the last mapped
entry for unmap_sg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement at32_add_device_cf() which will add a platform_device for
the at32_cf driver (not merged yet). Separate out most of the
at32_add_device_ide() code and use it to implement
at32_add_device_cf() as well.
This changes the API in the following ways:
* The board code must initialize data->cs to the chipselect ID to
use before calling any of these functions.
* The board code must use GPIO_PIN_NONE to indicate unused CF pins.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Implement functions for adding platform devices for TWI, MCI, AC97C
and ABDAC. They may need to be modified to cope with platform data,
etc. when the corresponding drivers are ready to be merged, but such
changes are much less likely to conflict than adding support for a
whole new type of device.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch adds platform code for PATA devices on the AP7000.
[hskinnemoen@atmel.com: board code left out for now since stk1000
doesn't support IDE out of the box]
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
arch/parisc/kernel/pci-dma.c: In function 'pa11_dma_map_sg':
arch/parisc/kernel/pci-dma.c:487: error: 'struct scatterlist' has no member named 'page'
arch/parisc/kernel/pci-dma.c: In function 'pa11_dma_unmap_sg':
arch/parisc/kernel/pci-dma.c:508: error: 'struct scatterlist' has no member named 'page'
arch/parisc/kernel/pci-dma.c:508: error: 'struct scatterlist' has no member named 'page'
arch/parisc/kernel/pci-dma.c: In function 'pa11_dma_sync_sg_for_cpu':
arch/parisc/kernel/pci-dma.c:535: error: 'struct scatterlist' has no member named 'page'
arch/parisc/kernel/pci-dma.c:535: error: 'struct scatterlist' has no member named 'page'
arch/parisc/kernel/pci-dma.c: In function 'pa11_dma_sync_sg_for_device':
arch/parisc/kernel/pci-dma.c:545: error: 'struct scatterlist' has no member named 'page'
arch/parisc/kernel/pci-dma.c:545: error: 'struct scatterlist' has no member named 'page'
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
arch/arm/common/dmabounce.c: In function 'dma_map_sg':
arch/arm/common/dmabounce.c:445: error: implicit declaration of function 'sg_page'
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Version 2.07 of the boot protocol uses 0x23C for the hardware_subarch
field, that for lguest is "1". This allows us to use the standard
boot entry point rather than the "GenuineLguest" string hack.
The standard entry point also clears the BSS and copies the boot parameters
and commandline for us, saving more code.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This makes lguest able to use the virtio devices.
We change the device descriptor page from a simple array to a variable
length "type, config_len, status, config data..." format, and
implement virtio_config_ops to read from that config data.
We use the virtio ring implementation for an efficient Guest <-> Host
virtqueue mechanism, and the new LHCALL_NOTIFY hypercall to kick the
host when it changes.
We also use LHCALL_NOTIFY on kernel addresses for very very early
console output. We could have another hypercall, but this hack works
quite well.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This gets rid of the lguest bus, drivers and DMA mechanism, to make
way for a generic virtio mechanism.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
These helper routines supply most of the virtqueue_ops for hypervisors
which want to use a ring for virtio. Unlike the previous lguest
implementation:
1) The rings are variable sized (2^n-1 elements).
2) They have an unfortunate limit of 65535 bytes per sg element.
3) The page numbers are always 64 bit (PAE anyone?)
4) They no longer place used[] on a separate page, just a separate
cacheline.
5) We do a modulo on a variable. We could be tricky if we cared.
6) Interrupts and notifies are suppressed using flags within the rings.
Users need only get the ring pages and provide a notify hook (KVM
wants the guest to allocate the rings, lguest does it sanely).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dor Laor <dor.laor@qumranet.com>
1) This allows us to get alot closer to booting bzImages.
2) It means we don't have to know page_offset.
3) The Guest needs to modify the boot pagetables to create the
PAGE_OFFSET mapping before jumping to C code.
4) guest_pa() walks the page tables rather than using page_offset.
5) We don't use page_offset to figure out whether to emulate: it was
always kinda quesationable, and won't work for instructions done
before remapping (bzImage unpacking in particular).
6) We still want the kernel address for tlb flushing: have the initial
hypercall give us that, too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
(Based on Ron Minnich's LGUEST_PLAN9_SYSCALL patch).
This patch allows Guests to specify what system call vector they want,
and we try to reserve it. We only allow one non-Linux system call
vector, to try to avoid DoS on the Host.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Clean up the hypercall code to make the code in hypercalls.c
architecture independent. First process the common hypercalls and
then call lguest_arch_do_hcall() if the call hasn't been handled.
Rename struct hcall_ring to hcall_args.
This patch requires the previous patch which reorganize the layout of
struct lguest_regs on i386 so they match the layout of struct
hcall_args.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Separate i386 architecture specific from core.c and move it to
x86/core.c and add x86/lguest.h header file to match.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Lguest has two sides: host support (to launch guests) and guest
support (replacement boot path and paravirt_ops). This moves the
guest side to arch/x86/lguest where it's closer to related code.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
1) Group all the "guest OS" support options together, under a PARAVIRT_GUEST
menu.
2) Make those options select CONFIG_PARAVIRT, as suggested by Andi.
3) Make kconfig help titles consistent.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Cc: Zach Amsden <zach@vmware.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Florian Fainelli