* pm-cpuidle:
suspend-to-idle: Prevent RCU from complaining about tick_freeze()
* pm-cpufreq:
cpufreq: Allow freq_table to be obtained for offline CPUs
cpufreq: Initialize the governor again while restoring policy
* acpi-resources:
ACPI / PCI: Fix regressions caused by resource_size_t overflow with 32-bit kernel
Users of freq table may want to access it for any CPU from
policy->related_cpus mask. One such user is cpu-cooling layer. It gets a
list of 'clip_cpus' (equivalent to policy->related_cpus) during
registration and tries to get freq_table for the first CPU of this mask.
If the CPU, for which it tries to fetch freq_table, is offline,
cpufreq_frequency_get_table() fails. This happens because it relies on
cpufreq_cpu_get_raw() for its functioning which returns policy only for
online CPUs.
The fix is to access the policy data structure for the given CPU
directly (which also returns a valid policy for offline CPUs), but the
policy itself has to be active (meaning that at least one CPU using it
is online) for the frequency table to be returned.
Because we will be using 'cpufreq_cpu_data' now, which is internal to
the cpufreq core, move cpufreq_frequency_get_table() to cpufreq.c.
Reported-and-tested-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When all CPUs of a policy are hot-unplugged, we EXIT the governor but
don't mark policy->governor as NULL. This was done in order to keep last
used governor's information intact in sysfs, while the CPUs are offline.
But we also need to clear policy->governor when restoring the policy.
Because policy->governor still points to the last governor while policy
is restored, following sequence of event happens:
- cpufreq_init_policy() called while restoring policy
- find_governor() matches last_governor string for present governors and
returns last used governor's pointer, say ondemand. policy->governor
already has the same address, unless the governor was removed in
between.
- cpufreq_set_policy() is called with both old/new policies governor set
as ondemand.
- Because governors matched, we skip governor initialization and return
after calling __cpufreq_governor(CPUFREQ_GOV_LIMITS). Because the
governor wasn't initialized for this policy, it returned -EBUSY.
- cpufreq_init_policy() exits the policy on this error, but doesn't
destroy it properly (should be fixed separately).
- And so we enter a scenario where the policy isn't completely
initialized but used.
Fix this by setting policy->governor to NULL while restoring the policy.
Reported-and-tested-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Reported-and-tested-by: "Jon Medhurst (Tixy)" <tixy@linaro.org>
Reported-and-tested-by: Steven Rostedt <rostedt@goodmis.org>
Fixes: 18bf3a124e (cpufreq: Mark policy->governor = NULL for inactive policies)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WLBw
-----END PGP SIGNATURE-----
Merge tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_platform_driver replacement from Paul Gortmaker:
"Replace module_platform_driver with builtin_platform driver in non
modules.
We see an increasing number of non-modular drivers using
modular_driver() type register functions. There are several downsides
to letting this continue unchecked:
- The code can appear modular to a reader of the code, and they won't
know if the code really is modular without checking the Makefile
and Kconfig to see if compilation is governed by a bool or
tristate.
- Coders of drivers may be tempted to code up an __exit function that
is never used, just in order to satisfy the required three args of
the modular registration function.
- Non-modular code ends up including the <module.h> which increases
CPP overhead that they don't need.
- It hinders us from performing better separation of the module init
code and the generic init code.
So here we introduce similar macros for builtin drivers. Then we
convert builtin drivers (controlled by a bool Kconfig) by making the
following type of mapping:
module_platform_driver() ---> builtin_platform_driver()
module_platform_driver_probe() ---> builtin_platform_driver_probe().
The set of drivers that are converted here are just the ones that
showed up as relying on an implicit include of <module.h> during a
pending header cleanup. So we convert them here vs adding an include
of <module.h> to non-modular code to avoid compile fails. Additonal
conversions can be done asynchronously at any time.
Once again, an unused module_exit function that is removed here
appears in the diffstat as an outlier wrt all the other changes"
* tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
drivers/clk: convert sunxi/clk-mod0.c to use builtin_platform_driver
drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver
drivers/soc: Convert non-modular soc-realview to use builtin_platform_driver
drivers/soc: Convert non-modular tegra/pmc to use builtin_platform_driver
drivers/cpufreq: Convert non-modular s5pv210-cpufreq.c to use builtin_platform_driver
drivers/cpuidle: Convert non-modular drivers to use builtin_platform_driver
drivers/platform: Convert non-modular pdev_bus to use builtin_platform_driver
platform_device: better support builtin boilerplate avoidance
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qotW
-----END PGP SIGNATURE-----
Merge tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull implicit module.h fixes from Paul Gortmaker:
"Fix up implicit <module.h> users that will break later.
The files changed here are simply modular source files that are
implicitly relying on <module.h> being present. We fix them up now,
so that we can decouple some of the module related init code from the
core init code in the future.
The addition of the module.h include to several files here is also a
no-op from a code generation point of view, else there would already
be compile issues with these files today.
There may be lots more implicit includes of <module.h> in tree, but
these are the ones that extensive build test coverage has shown that
must be fixed in order to avoid build breakage fallout for the pending
module.h <---> init.h code relocation we desire to complete"
* tag 'module-implicit-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
frv: add module.h to mb93090-mb00/flash.c to avoid compile fail
drivers/cpufreq: include <module.h> for modular exynos-cpufreq.c code
drivers/staging: include <module.h> for modular android tegra_ion code
crypto/asymmetric_keys: pkcs7_key_type needs module.h
sh: mach-highlander/psw.c is tristate and should use module.h
drivers/regulator: include <module.h> for modular max77802 code
drivers/pcmcia: include <module.h> for modular xxs1500_ss code
drivers/hsi: include <module.h> for modular omap_ssi code
drivers/gpu: include <module.h> for modular rockchip code
drivers/gpio: include <module.h> for modular crystalcove code
drivers/clk: include <module.h> for clk-max77xxx modular code
drivers and updates to existing ones, as usual. There are some fixes to
the framework itself and several cleanups for sparse warnings, etc.
Please consider pulling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Iv72
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework updates from Michael Turquette:
"The changes to the common clock framework for 4.2 are dominated by new
drivers and updates to existing ones, as usual.
There are some fixes to the framework itself and several cleanups for
sparse warnings, etc"
* tag 'clk-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (135 commits)
clk: stm32: Add clock driver for STM32F4[23]xxx devices
dt-bindings: Document the STM32F4 clock bindings
cpufreq: exynos: remove Exynos4210 specific cpufreq driver support
ARM: Exynos: switch to using generic cpufreq driver for Exynos4210
clk: samsung: exynos4: add cpu clock configuration data and instantiate cpu clock
clk: samsung: add infrastructure to register cpu clocks
clk: add CLK_RECALC_NEW_RATES clock flag for Exynos cpu clock support
doc: dt: add documentation for lpc1850-ccu clk driver
clk: add lpc18xx ccu clk driver
doc: dt: add documentation for lpc1850-cgu clk driver
clk: add lpc18xx cgu clk driver
clk: keystone: add support for post divider register for main pll
clk: mvebu: flag the crypto clk as CLK_IGNORE_UNUSED
clk: cygnus: remove Cygnus dummy clock binding
clk: cygnus: add clock support for Broadcom Cygnus
clk: Change bcm clocks build dependency
clk: iproc: add initial common clock support
clk: iproc: define Broadcom iProc clock binding
MAINTAINERS: update email for Michael Turquette
clk: meson: add some error handling in meson_clk_register_cpu()
...
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
- ACPICA update to upstream revision 20150515 including basic
support for ACPI 6 features: new ACPI tables introduced by
ACPI 6 (STAO, XENV, WPBT, NFIT, IORT), changes related to the
other tables (DTRM, FADT, LPIT, MADT), new predefined names
(_BTH, _CR3, _DSD, _LPI, _MTL, _PRR, _RDI, _RST, _TFP, _TSN),
fixes and cleanups (Bob Moore, Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation
in Windows (Rafael J Wysocki).
- Rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling
of DMI quirks that may be involved in that and to make the
code generally more straightforward (Hans de Goede).
- Fixes for the ACPI Embedded Controller (EC) driver related to
the handling of EC transactions (Lv Zheng).
- Fix for a regression related to the ACPI resources management
and resulting from a recent change of ACPI initialization code
ordering (Rafael J Wysocki).
- Fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the
code that switches the platform over to the ACPI mode too
early in the initialization sequence (Rafael J Wysocki).
- Support for the ACPI _CCA device configuration object related
to DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- Cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- Assorted cleanups related to ACPI (Dominik Brodowski. Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- Fix for a long-standing issue causing General Protection Faults
to be generated occasionally on return to user space after resume
from ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- Fix to make the suspend core code return -EBUSY consistently in
all cases when system suspend is aborted due to wakeup detection
(Ruchi Kandoi).
- Support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- New tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- Wakeup sources framework enhancements (Jin Qian).
- New macro for noirq system PM callbacks (Grygorii Strashko).
- Assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should
reduce the overhead of these operations quite a bit, unless the
CPU in question is physically going away (Viresh Kumar, Saravana
Kannan).
- Serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- Assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- New Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- Updates for the common clock operations support code in the PM
core (Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- Fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- Runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7jTj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
Currently, code of Loongson-2/3 is under loongson directory and code of
Loongson-1 is under loongson1 directory. Besides, there are Kconfig
options such as MACH_LOONGSON and MACH_LOONGSON1. This naming style is
very ugly and confusing. Since Loongson-2/3 are both 64-bit general-
purpose CPU while Loongson-1 is 32-bit SoC, we rename both file names
and Kconfig symbols from loongson/loongson1 to loongson64/loongson32.
[ralf@linux-mips.org: Resolve a number of simple conflicts.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9790/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Exynos4210 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufreq support for these platforms can be removed.
Changes by Bartlomiej:
- dropped Exynos5250 support removal for now
- updated exynos-cpufreq.[c,h]
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
by adding the missing MODULE_ALIAS(), cpufreq-dt
can be autoloaded by udev/systemd.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This file depends on a Kconfig option which is a bool, so
we use the appropriate registration function, which avoids us
relying on an implicit inclusion of <module.h> which we are
doing currently.
While this currently works, we really don't want to be including
the module.h header in non-modular code, which we'd be forced
to do, pending some upcoming code relocation from init.h into
module.h. So we fix it now by using the non-modular equivalent.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This file is built off of a tristate Kconfig option ("ARM_EXYNOS_CPUFREQ")
and also contains modular function calls so it should explicitly include
module.h to avoid compile breakage during pending header shuffles.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Each time the CPU switches its frequency, the clock nodes in
DTS are walked through to find proper clock source. This is
very time-consuming, for example, it is up to 500+ us on T4240.
Besides, switching time varies from clock to clock.
To optimize this, each input clock of CPU is buffered, so that
it can be picked up instantly when needed.
Since for each CPU each input clock is stored in a pointer
which takes 4 or 8 bytes memory and normally there are several
input clocks per CPU, that will not take much memory as well.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are several races reported in cpufreq core around governors (only
ondemand and conservative) by different people.
There are at least two race scenarios present in governor code:
(a) Concurrent access/updates of governor internal structures.
It is possible that fields such as 'dbs_data->usage_count', etc. are
accessed simultaneously for different policies using same governor
structure (i.e. CPUFREQ_HAVE_GOVERNOR_PER_POLICY flag unset). And
because of this we can dereference bad pointers.
For example consider a system with two CPUs with separate 'struct
cpufreq_policy' instances. CPU0 governor: ondemand and CPU1: powersave.
CPU0 switching to powersave and CPU1 to ondemand:
CPU0 CPU1
store* store*
cpufreq_governor_exit() cpufreq_governor_init()
dbs_data = cdata->gdbs_data;
if (!--dbs_data->usage_count)
kfree(dbs_data);
dbs_data->usage_count++;
*Bad pointer dereference*
There are other races possible between EXIT and START/STOP/LIMIT as
well. Its really complicated.
(b) Switching governor state in bad sequence:
For example trying to switch a governor to START state, when the
governor is in EXIT state. There are some checks present in
__cpufreq_governor() but they aren't sufficient as they compare events
against 'policy->governor_enabled', where as we need to take governor's
state into account, which can be used by multiple policies.
These two issues need to be solved separately and the responsibility
should be properly divided between cpufreq and governor core.
The first problem is more about the governor core, as it needs to
protect its structures properly. And the second problem should be fixed
in cpufreq core instead of governor, as its all about sequence of
events.
This patch is trying to solve only the first problem.
There are two types of data we need to protect,
- 'struct common_dbs_data': No matter what, there is going to be a
single copy of this per governor.
- 'struct dbs_data': With CPUFREQ_HAVE_GOVERNOR_PER_POLICY flag set, we
will have per-policy copy of this data, otherwise a single copy.
Because of such complexities, the mutex present in 'struct dbs_data' is
insufficient to solve our problem. For example we need to protect
fetching of 'dbs_data' from different structures at the beginning of
cpufreq_governor_dbs(), to make sure it isn't currently being updated.
This can be fixed if we can guarantee serialization of event parsing
code for an individual governor. This is best solved with a mutex per
governor, and the placeholder for that is 'struct common_dbs_data'.
And so this patch moves the mutex from 'struct dbs_data' to 'struct
common_dbs_data' and takes it at the beginning and drops it at the end
of cpufreq_governor_dbs().
Tested with and without following configuration options:
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_DEBUG_RT_MUTEXES=y
CONFIG_DEBUG_PI_LIST=y
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_LOCK_ALLOC=y
CONFIG_PROVE_LOCKING=y
CONFIG_LOCKDEP=y
CONFIG_DEBUG_ATOMIC_SLEEP=y
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_governor_dbs() is hardly readable, it is just too big and
complicated. Lets make it more readable by splitting out event specific
routines.
Order of statements is changed at few places, but that shouldn't bring
any functional change.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Notifiers are required only for conservative governor and the common
governor code is unnecessarily polluted with that. Handle that from
cs_init/exit() instead of cpufreq_governor_dbs().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_update_policy() was kept as a separate routine earlier as it was
handling migration of sysfs directories, which isn't the case anymore.
It is only updating policy->cpu now and is called by a single caller.
The WARN_ON() isn't really required anymore, as we are just updating the
cpu now, not moving the sysfs directories.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__cpufreq_remove_dev_finish() is doing two things today:
- Restarts the governor if some CPUs from concerned policy are still
online.
- Frees the policy if all CPUs are offline.
The first task of restarting the governor can be moved to
__cpufreq_remove_dev_prepare() to restart the governor early. There is
no race between _prepare() and _finish() as they would be handling
completely different cases. _finish() will only be required if we are
going to free the policy and that has nothing to do with restarting the
governor.
Original-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_policy_put_kobj() is actually part of freeing the policy and can
be called from cpufreq_policy_free() directly instead of a separate
call.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->kobj is required to be initialized once in the lifetime of a
policy. Currently we are initializing it from __cpufreq_add_dev() and
that doesn't look to be the best place for doing so as we have to do
this on special cases (like: !recover_policy).
We can initialize it from a more obvious place cpufreq_policy_alloc()
and that will make code look cleaner, specially the error handling part.
The error handling part of __cpufreq_add_dev() was doing almost the same
thing while recover_policy is true or false. Fix that as well by always
calling cpufreq_policy_put_kobj() with an additional parameter to skip
notification part of it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When we hot-unplug a cpu, we remove its sysfs cpufreq directory and if
the outgoing cpu was the owner of policy->kobj earlier then we migrate
the sysfs directory to under another online cpu.
There are few disadvantages this brings:
- Code Complexity
- Slower hotplug/suspend/resume
- sysfs file permissions are reset after all policy->cpus are offlined
- CPUFreq stats history lost after all policy->cpus are offlined
- Special management of sysfs stuff during suspend/resume
To overcome these, this patch modifies the way sysfs directories are
managed:
- Select sysfs kobjects owner while initializing policy and don't change
it during hotplugs. Track it with kobj_cpu created earlier.
- Create symlinks for all related CPUs (can be offline) instead of
affected CPUs on policy initialization and remove them only when the
policy is freed.
- Free policy structure only on the removal of cpufreq-driver and not
during hotplug/suspend/resume, detected by checking 'struct
subsys_interface *' (Valid only when called from
subsys_interface_unregister() while unregistering driver).
Apart from this, special care is taken to handle physical hoplug of CPUs
as we wouldn't remove sysfs links or remove policies on logical
hotplugs. Physical hotplug happens in the following sequence.
Hot removal:
- CPU is offlined first, ~ 'echo 0 >
/sys/devices/system/cpu/cpuX/online'
- Then its device is removed along with all sysfs files, cpufreq core
notified with cpufreq_remove_dev() callback from subsys-interface..
Hot addition:
- First the device along with its sysfs files is added, cpufreq core
notified with cpufreq_add_dev() callback from subsys-interface..
- CPU is onlined, ~ 'echo 1 > /sys/devices/system/cpu/cpuX/online'
We call the same routines with both hotplug and subsys callbacks, and we
sense physical hotplug with cpu_offline() check in subsys callback. We
can handle most of the stuff with regular hotplug callback paths and
add/remove cpufreq sysfs links or free policy from subsys callbacks.
Original-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Later commits would change the way policies are managed today. Policies
wouldn't be freed on cpu hotplug (currently they aren't freed only for
suspend), and while the CPU is offline, the sysfs cpufreq files would
still be present.
User may accidentally try to update the sysfs files in following
directory: '/sys/devices/system/cpu/cpuX/cpufreq/'. And that would
result in undefined behavior as policy wouldn't be active then.
Apart from updating the store() routine, we also update __cpufreq_get()
which can call cpufreq_out_of_sync(). The later routine tries to update
policy->cur and starts notifying kernel about it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During initialization and exit it is possible that the target pstate
might not actually be set. Furthermore, the result can be that the
driver and the processor are out of synch and, under some conditions,
the driver might never send the processor the proper target pstate.
This patch adds a bypass or do_checks flag to the call to
intel_pstate_set_pstate. If bypass, then specifically bypass clamp
checks and the do not send if it is the same as last time check. If
do_checks, then, and as before, do the current policy clamp checks,
and do not do actual send if the new target is the same as the old.
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Reported-by: Marien Zwart <marien.zwart@gmail.com>
Reported-by: Alex Lochmann <alexander.lochmann@tu-dortmund.de>
Reported-by: Piotr Ko?aczkowski <pkolaczk@gmail.com>
Reported-by: Clemens Eisserer <linuxhippy@gmail.com>
Tested-by: Marien Zwart <marien.zwart@gmail.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
[ rjw: Dropped pointless symbol definitions, rebased ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit ce717613f3 (intel_pstate: Turn per cpu printk into pr_debug)
turned per cpu printk into pr_debug. However, only half of the change
was done, introducing an inconsistency between entry and exit from
driver pstate control. This patch changes the exit message to pr_debug
also.
The various messages are inconsistent with respect to any identifier
text that can be used to help isolate the desired information from a
huge log. This patch makes a consistent identifier portion of the
string.
Amends: ce717613f3 (intel_pstate: Turn per cpu printk into pr_debug)
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Nothing in <asm/io.h> uses anything from <linux/vmalloc.h>, so
remove it from there and fix up the resulting build problems
triggered on x86 {64|32}-bit {def|allmod|allno}configs.
The breakages were triggering in places where x86 builds relied
on vmalloc() facilities but did not include <linux/vmalloc.h>
explicitly and relied on the implicit inclusion via <asm/io.h>.
Also add:
- <linux/init.h> to <linux/io.h>
- <asm/pgtable_types> to <asm/io.h>
... which were two other implicit header file dependencies.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[ Tidied up the changelog. ]
Acked-by: David Miller <davem@davemloft.net>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Colin Cross <ccross@android.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Suma Ramars <sramars@cisco.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The former duplicates the functionality of the latter but is
neither documented nor arch-independent.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1432645896-12588-8-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The former duplicate the functionalities of the latter but are
neither documented nor arch-independent.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1432645896-12588-7-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The former duplicates the functionality of the latter but is
neither documented nor arch-independent.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1432645896-12588-6-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The former duplicates the functionality of the latter but is
neither documented nor arch-independent.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1432645896-12588-5-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In order to prepare for the next few commits, that will stop migrating
sysfs files on cpu hotplug, this patch starts managing sysfs-cpu
separately.
The behavior is still the same as we are still migrating sysfs files on
hotplug, later commits would change that.
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Later commits would change the way policies are managed today. Policies
wouldn't be freed on cpu hotplug (currently they aren't freed on
suspend), and while the CPU is offline, the sysfs cpufreq files would
still be present.
Because we don't mark policy->governor as NULL, it still contains
pointer of the last used governor. And if the governor is removed, while
all the CPUs of a policy are hotplugged out, this pointer wouldn't be
valid anymore. And if we try to read the 'scaling_governor', etc. from
sysfs, it will result in kernel OOPs.
To prevent this, mark policy->governor as NULL for all inactive policies
while the governor is removed from kernel.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
History of which governor was used last is common to all CPUs within a
policy and maintaining it per-cpu isn't the best approach for sure.
Apart from wasting memory, this also increases the complexity of
managing this data structure as it has to be updated for all CPUs.
To make that somewhat simpler, lets store this information in a new
field 'last_governor' in struct cpufreq_policy and update it on removal
of last cpu of a policy.
As a side-effect it also solves an old problem, consider a system with
two clusters 0 & 1. And there is one policy per cluster.
Cluster 0: CPU0 and 1.
Cluster 1: CPU2 and 3.
- CPU2 is first brought online, and governor is set to performance
(default as cpufreq_cpu_governor wasn't set).
- Governor is changed to ondemand.
- CPU2 is taken offline and cpufreq_cpu_governor is updated for CPU2.
- CPU3 is brought online.
- Because cpufreq_cpu_governor wasn't set for CPU3, the default governor
performance is picked for CPU3.
This patch fixes the bug as we now have a single variable to update for
policy.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We reach here while adding policy for a CPU and enter into the 'if'
block only if a policy already exists for the CPU.
As cpufreq_cpu_data is set for all policy->related_cpus now, when the
policy is first added, we can use that to find the CPU's policy instead
of traversing the list of all active policies.
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We can extract the same information from cpufreq_cpu_data as it is also
available for inactive policies now. And so don't need
cpufreq_cpu_data_fallback anymore.
Also add a WARN_ON() for the case where we try to restore from an active
policy.
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we can check policy->cpus to find if policy is active or not,
we don't need to clean cpufreq_cpu_data and delete policy from the list
on light weight tear down of policies (like in suspend).
To make it consistent and clean, set cpufreq_cpu_data for all related
CPUs when the policy is first created and clean it only while it is
freed.
Also update cpufreq_cpu_get_raw() to check if cpu is part of
policy->cpus mask, so that we don't end up getting policies for offline
CPUs.
In order to make sure that no users of 'policy' are using an inactive
policy, use cpufreq_cpu_get_raw() instead of directly accessing
cpufreq_cpu_data.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->cpus is cleared unconditionally now on hotplug-out of a CPU and
it can be checked to know if a policy is active or not. Create helper
routines to iterate over all active/inactive policies, based on
policy->cpus field.
Replace all instances of for_each_policy() with for_each_active_policy()
to make them iterate only for active policies. (We haven't made changes
yet to keep inactive policies in the same list, but that will be
followed in a later patch).
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the addition of switcher code, there's compile-time dependency on
BIG_LITTLE to get arm_big_little driver compiling on ARM64. Since ARM64
will never add support for bL switcher, it's better to remove the
dependency so that the driver can be reused on ARM64 platforms.
This patch adds stubs to remove BIG_LITTLE dependency in the driver.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 007bea098b (intel_pstate: Add setting voltage value for
baytrail P states.) introduced byt_set_pstate() with the assumption that
it would always be run by the CPU whose MSR is to be written by it. It
turns out, however, that is not always the case in practice, so modify
byt_set_pstate() to enforce the MSR write done by it to always happen on
the right CPU.
Fixes: 007bea098b (intel_pstate: Add setting voltage value for baytrail P states.)
Signed-off-by: Joe Konno <joe.konno@intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We clear policy->cpus mask while CPUs are hotplugged out. We do it for all CPUs
except the last CPU of the policy. I don't remember what the rationale behind
that was, but I couldn't think of anything that will break if we remove this
conditional clearing and always clear policy->cpus.
The benefit we get out of it is, we can know if a policy is active or not by
checking if this field is empty or not. That will be used by later commits.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two cases when we may try to add CPUs we're already handling:
- On boot, the first cpu has marked all policy->cpus managed and so we
will find policy for all other policy->cpus later on.
- When a managed cpu is hotplugged out and later brought back in.
Currently, separate paths and checks take care of the two. While the
first one is detected by testing cpu against 'policy->cpus', the other
one is detected by testing cpu against 'policy->related_cpus'.
We can handle them both via a single path and there is no need to do
special checking for the first one.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
[ rjw: Changelog, comments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Simply returning here with an error is not enough. It shouldn't be allowed at
all to try calling cpufreq_cpu_get() for an invalid CPU.
Add a WARN here to make it clear that it wouldn't be acceptable at all.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ingo Molnar