If arp_format_neigh_entry() can be called with n->dev->addr_len == 0, then a
write to hbuffer[-1] occurs.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the TCP connection handshake completes on the passive
side, a variety of state must be set up in the "child" sock,
including the key if MD5 authentication is being used. Fix TCP
for both address families to label the key with the peer's
destination address, rather than the address from the listening
sock, which is usually the wildcard.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix MD5 signature checking so that an IPv4 active open
to an IPv6 socket can succeed. In particular, use the
correct address family's signature generation function
for the SYN/ACK.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes two bugs:
- ToS/DiffServ inheritance was unintentionally activated when using impair fixed ToS values
- ECN bit was lost during ToS/DiffServ inheritance
Signed-off-by: Andreas Jaggi <aj@open.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 2b85a34e91
(net: No more expensive sock_hold()/sock_put() on each tx)
we do not take any more references on sk->sk_refcnt on outgoing packets.
I forgot to delete two __sock_put() from ip_push_pending_frames()
and ip6_push_pending_frames().
Reported-by: Emil S Tantilov <emils.tantilov@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Emil S Tantilov <emils.tantilov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding memory barrier after the poll_wait function, paired with
receive callbacks. Adding fuctions sock_poll_wait and sk_has_sleeper
to wrap the memory barrier.
Without the memory barrier, following race can happen.
The race fires, when following code paths meet, and the tp->rcv_nxt
and __add_wait_queue updates stay in CPU caches.
CPU1 CPU2
sys_select receive packet
... ...
__add_wait_queue update tp->rcv_nxt
... ...
tp->rcv_nxt check sock_def_readable
... {
schedule ...
if (sk->sk_sleep && waitqueue_active(sk->sk_sleep))
wake_up_interruptible(sk->sk_sleep)
...
}
If there was no cache the code would work ok, since the wait_queue and
rcv_nxt are opposit to each other.
Meaning that once tp->rcv_nxt is updated by CPU2, the CPU1 either already
passed the tp->rcv_nxt check and sleeps, or will get the new value for
tp->rcv_nxt and will return with new data mask.
In both cases the process (CPU1) is being added to the wait queue, so the
waitqueue_active (CPU2) call cannot miss and will wake up CPU1.
The bad case is when the __add_wait_queue changes done by CPU1 stay in its
cache, and so does the tp->rcv_nxt update on CPU2 side. The CPU1 will then
endup calling schedule and sleep forever if there are no more data on the
socket.
Calls to poll_wait in following modules were ommited:
net/bluetooth/af_bluetooth.c
net/irda/af_irda.c
net/irda/irnet/irnet_ppp.c
net/mac80211/rc80211_pid_debugfs.c
net/phonet/socket.c
net/rds/af_rds.c
net/rfkill/core.c
net/sunrpc/cache.c
net/sunrpc/rpc_pipe.c
net/tipc/socket.c
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pawel Staszewski wrote:
<blockquote>
Some time ago i report this:
http://bugzilla.kernel.org/show_bug.cgi?id=6648
and now with 2.6.29 / 2.6.29.1 / 2.6.29.3 and 2.6.30 it back
dmesg output:
oprofile: using NMI interrupt.
Fix inflate_threshold_root. Now=15 size=11 bits
...
Fix inflate_threshold_root. Now=15 size=11 bits
cat /proc/net/fib_triestat
Basic info: size of leaf: 40 bytes, size of tnode: 56 bytes.
Main:
Aver depth: 2.28
Max depth: 6
Leaves: 276539
Prefixes: 289922
Internal nodes: 66762
1: 35046 2: 13824 3: 9508 4: 4897 5: 2331 6: 1149 7: 5
9: 1 18: 1
Pointers: 691228
Null ptrs: 347928
Total size: 35709 kB
</blockquote>
It seems, the current threshold for root resizing is too aggressive,
and it causes misleading warnings during big updates, but it might be
also responsible for memory problems, especially with non-preempt
configs, when RCU freeing is delayed long after call_rcu.
It should be also mentioned that because of non-atomic changes during
resizing/rebalancing the current lookup algorithm can miss valid leaves
so it's additional argument to shorten these activities even at a cost
of a minimally longer searching.
This patch restores values before the patch "[IPV4]: fib_trie root
node settings", commit: 965ffea43d from
v2.6.22.
Pawel's report:
<blockquote>
I dont see any big change of (cpu load or faster/slower
routing/propagating routes from bgpd or something else) - in avg there
is from 2% to 3% more of CPU load i dont know why but it is - i change
from "preempt" to "no preempt" 3 times and check this my "mpstat -P ALL
1 30"
always avg cpu load was from 2 to 3% more compared to "no preempt"
[...]
cat /proc/net/fib_triestat
Basic info: size of leaf: 20 bytes, size of tnode: 36 bytes.
Main:
Aver depth: 2.44
Max depth: 6
Leaves: 277814
Prefixes: 291306
Internal nodes: 66420
1: 32737 2: 14850 3: 10332 4: 4871 5: 2313 6: 942 7: 371 8: 3 17: 1
Pointers: 599098
Null ptrs: 254865
Total size: 18067 kB
</blockquote>
According to this and other similar reports average depth is slightly
increased (~0.2), and root nodes are shorter (log 17 vs. 18), but
there is no visible performance decrease. So, until memory handling is
improved or added parameters for changing this individually, this
patch resets to safer defaults.
Reported-by: Pawel Staszewski <pstaszewski@itcare.pl>
Reported-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP pushed the skb data above the sctp chunk header, so the check
of pskb_may_pull(skb, xprth + 4 - skb->data) in _decode_session4() will
never return 0 because xprth + 4 - skb->data < 0, the ports decode of
sctp will always fail.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 73ce7b01b4.
After discovering that we don't listen to gratuitious arps in 2.6.30
I tracked the failure down to this commit.
The patch makes absolutely no sense. RFC2131 RFC3927 and RFC5227.
are all in agreement that an arp request with sip == 0 should be used
for the probe (to prevent learning) and an arp request with sip == tip
should be used for the gratitous announcement that people can learn
from.
It appears the author of the broken patch got those two cases confused
and modified the code to drop all gratuitous arp traffic. Ouch!
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alas current delaying of freeing old tnodes by RCU in trie_rebalance
is still not enough because we can free a top tnode before updating a
t->trie pointer.
Reported-by: Pawel Staszewski <pstaszewski@itcare.pl>
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a socket starts out on a non-TSO route, and then switches to
a TSO route, then we will tack on data to the tail of the tx queue
even if it started out life as non-TSO. This is suboptimal because
all of it will then be copied and checksummed unnecessarily.
This patch fixes this by ensuring that skb->ip_summed is set to
CHECKSUM_PARTIAL before appending extra data beyond the MSS.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a socket starts out on a non-TSO route, and then switches to
a TSO route, then the tail on the tx queue can morph into a TSO
packet, causing mischief because the rest of the stack does not
expect a partially linear TSO packet.
This patch fixes this by ensuring that skb->ip_summed is set to
CHECKSUM_PARTIAL before declaring a packet as TSO.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NAT helpers change the TCP packet size, the highest seen sequence
number needs to be corrected. This is currently only done upwards, when
the packet size is reduced the sequence number is unchanged. This causes
TCP conntrack to falsely detect unacknowledged data and decrease the
timeout.
Fix by updating the highest seen sequence number in both directions after
packet mangling.
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
As transparent proxying looks up the socket early and assigns
it to the skb for later processing, we must drop any existing
socket ownership prior to that in order to distinguish between
the case where tproxy is active and where it is not.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC0793 defined that in FIN-WAIT-2 state if the ACK bit is off drop
the segment and return[Page 72]. But this check is missing in function
tcp_timewait_state_process(). This cause the segment with FIN flag but
no ACK has two diffent action:
Case 1:
Node A Node B
<------------- FIN,ACK
(enter FIN-WAIT-1)
ACK ------------->
(enter FIN-WAIT-2)
FIN -------------> discard
(move sk to tw list)
Case 2:
Node A Node B
<------------- FIN,ACK
(enter FIN-WAIT-1)
ACK ------------->
(enter FIN-WAIT-2)
(move sk to tw list)
FIN ------------->
<------------- ACK
This patch fixed the problem.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6:
bnx2: Fix the behavior of ethtool when ONBOOT=no
qla3xxx: Don't sleep while holding lock.
qla3xxx: Give the PHY time to come out of reset.
ipv4 routing: Ensure that route cache entries are usable and reclaimable with caching is off
net: Move rx skb_orphan call to where needed
ipv6: Use correct data types for ICMPv6 type and code
net: let KS8842 driver depend on HAS_IOMEM
can: let SJA1000 driver depend on HAS_IOMEM
netxen: fix firmware init handshake
netxen: fix build with without CONFIG_PM
netfilter: xt_rateest: fix comparison with self
netfilter: xt_quota: fix incomplete initialization
netfilter: nf_log: fix direct userspace memory access in proc handler
netfilter: fix some sparse endianess warnings
netfilter: nf_conntrack: fix conntrack lookup race
netfilter: nf_conntrack: fix confirmation race condition
netfilter: nf_conntrack: death_by_timeout() fix
When route caching is disabled (rt_caching returns false), We still use route
cache entries that are created and passed into rt_intern_hash once. These
routes need to be made usable for the one call path that holds a reference to
them, and they need to be reclaimed when they're finished with their use. To be
made usable, they need to be associated with a neighbor table entry (which they
currently are not), otherwise iproute_finish2 just discards the packet, since we
don't know which L2 peer to send the packet to. To do this binding, we need to
follow the path a bit higher up in rt_intern_hash, which calls
arp_bind_neighbour, but not assign the route entry to the hash table.
Currently, if caching is off, we simply assign the route to the rp pointer and
are reutrn success. This patch associates us with a neighbor entry first.
Secondly, we need to make sure that any single use routes like this are known to
the garbage collector when caching is off. If caching is off, and we try to
hash in a route, it will leak when its refcount reaches zero. To avoid this,
this patch calls rt_free on the route cache entry passed into rt_intern_hash.
This places us on the gc list for the route cache garbage collector, so that
when its refcount reaches zero, it will be reclaimed (Thanks to Alexey for this
suggestion).
I've tested this on a local system here, and with these patches in place, I'm
able to maintain routed connectivity to remote systems, even if I set
/proc/sys/net/ipv4/rt_cache_rebuild_count to -1, which forces rt_caching to
return false.
Signed-off-by: Neil Horman <nhorman@redhat.com>
Reported-by: Jarek Poplawski <jarkao2@gmail.com>
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (43 commits)
via-velocity: Fix velocity driver unmapping incorrect size.
mlx4_en: Remove redundant refill code on RX
mlx4_en: Removed redundant check on lso header size
mlx4_en: Cancel port_up check in transmit function
mlx4_en: using stop/start_all_queues
mlx4_en: Removed redundant skb->len check
mlx4_en: Counting all the dropped packets on the TX side
usbnet cdc_subset: fix issues talking to PXA gadgets
Net: qla3xxx, remove sleeping in atomic
ipv4: fix NULL pointer + success return in route lookup path
isdn: clean up documentation index
cfg80211: validate station settings
cfg80211: allow setting station parameters in mesh
cfg80211: allow adding/deleting stations on mesh
ath5k: fix beacon_int handling
MAINTAINERS: Fix Atheros pattern paths
ath9k: restore PS mode, before we put the chip into FULL SLEEP state.
ath9k: wait for beacon frame along with CAB
acer-wmi: fix rfkill conversion
ath5k: avoid PCI FATAL interrupts by restoring RETRY_TIMEOUT disabling
...
Don't drop route if we're not caching
I recently got a report of an oops on a route lookup. Maxime was
testing what would happen if route caching was turned off (doing so by setting
making rt_caching always return 0), and found that it triggered an oops. I
looked at it and found that the problem stemmed from the fact that the route
lookup routines were returning success from their lookup paths (which is good),
but never set the **rp pointer to anything (which is bad). This happens because
in rt_intern_hash, if rt_caching returns false, we call rt_drop and return 0.
This almost emulates slient success. What we should be doing is assigning *rp =
rt and _not_ dropping the route. This way, during slow path lookups, when we
create a new route cache entry, we don't immediately discard it, rather we just
don't add it into the cache hash table, but we let this one lookup use it for
the purpose of this route request. Maxime has tested and reports it prevents
the oops. There is still a subsequent routing issue that I'm looking into
further, but I'm confident that, even if its related to this same path, this
patch makes sense to take.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (55 commits)
netxen: fix tx ring accounting
netxen: fix detection of cut-thru firmware mode
forcedeth: fix dma api mismatches
atm: sk_wmem_alloc initial value is one
net: correct off-by-one write allocations reports
via-velocity : fix no link detection on boot
Net / e100: Fix suspend of devices that cannot be power managed
TI DaVinci EMAC : Fix rmmod error
net: group address list and its count
ipv4: Fix fib_trie rebalancing, part 2
pkt_sched: Update drops stats in act_police
sky2: version 1.23
sky2: add GRO support
sky2: skb recycling
sky2: reduce default transmit ring
sky2: receive counter update
sky2: fix shutdown synchronization
sky2: PCI irq issues
sky2: more receive shutdown
sky2: turn off pause during shutdown
...
Manually fix trivial conflict in net/core/skbuff.c due to kmemcheck
commit 2b85a34e91
(net: No more expensive sock_hold()/sock_put() on each tx)
changed initial sk_wmem_alloc value.
We need to take into account this offset when reporting
sk_wmem_alloc to user, in PROC_FS files or various
ioctls (SIOCOUTQ/TIOCOUTQ)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My previous patch, which explicitly delays freeing of tnodes by adding
them to the list to flush them after the update is finished, isn't
strict enough. It treats exceptionally tnodes without parent, assuming
they are newly created, so "invisible" for the read side yet.
But the top tnode doesn't have parent as well, so we have to exclude
all exceptions (at least until a better way is found). Additionally we
need to move rcu assignment of this node before flushing, so the
return type of the trie_rebalance() function is changed.
Reported-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of bitfields here would lead to false positive warnings with
kmemcheck. Silence them.
(Additionally, one erroneous comment related to the bitfield was also
fixed.)
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
While doing trie_rebalance(): resize(), inflate(), halve() RCU free
tnodes before updating their parents. It depends on RCU delaying the
real destruction, but if RCU readers start after call_rcu() and before
parent update they could access freed memory.
It is currently prevented with preempt_disable() on the update side,
but it's not safe, except maybe classic RCU, plus it conflicts with
memory allocations with GFP_KERNEL flag used from these functions.
This patch explicitly delays freeing of tnodes by adding them to the
list, which is flushed after the update is finished.
Reported-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4:
- make PIM register vifs netns local
- set the netns when a PIM register vif is created
- make PIM available in all network namespaces (if CONFIG_IP_PIMSM_V2)
by adding the protocol handler when multicast routing is initialized
IPv6:
- make PIM register vifs netns local
- make PIM available in all network namespaces (if CONFIG_IPV6_PIMSM_V2)
by adding the protocol handler when multicast routing is initialized
Signed-off-by: Tom Goff <thomas.goff@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed the statements about ARP cache size as this config option does
not affect it. The cache size is controlled by neigh_table gc thresholds.
Remove also expiremental and obsolete markings as the API originally
intended for arp caching is useful for implementing ARP-like protocols
(e.g. NHRP) in user space and has been there for a long enough time.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of power saver lovers, use a deferrable timer to fire
rt_check_expire()
As some big routers cache equilibrium depends on garbage collection
done in time, we take into account elapsed time between two
rt_check_expire() invocations to adjust the amount of slots we have to
check.
Based on an initial idea and patch from Tero Kristo
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build error introduced by commit bb70dfa5 (netfilter: xtables:
consolidate comefrom debug cast access):
net/ipv4/netfilter/ip_tables.c: In function 'ipt_do_table':
net/ipv4/netfilter/ip_tables.c:421: error: 'comefrom' undeclared (first use in this function)
net/ipv4/netfilter/ip_tables.c:421: error: (Each undeclared identifier is reported only once
net/ipv4/netfilter/ip_tables.c:421: error: for each function it appears in.)
Signed-off-by: Patrick McHardy <kaber@trash.net>
One of the problem with sock memory accounting is it uses
a pair of sock_hold()/sock_put() for each transmitted packet.
This slows down bidirectional flows because the receive path
also needs to take a refcount on socket and might use a different
cpu than transmit path or transmit completion path. So these
two atomic operations also trigger cache line bounces.
We can see this in tx or tx/rx workloads (media gateways for example),
where sock_wfree() can be in top five functions in profiles.
We use this sock_hold()/sock_put() so that sock freeing
is delayed until all tx packets are completed.
As we also update sk_wmem_alloc, we could offset sk_wmem_alloc
by one unit at init time, until sk_free() is called.
Once sk_free() is called, we atomic_dec_and_test(sk_wmem_alloc)
to decrement initial offset and atomicaly check if any packets
are in flight.
skb_set_owner_w() doesnt call sock_hold() anymore
sock_wfree() doesnt call sock_put() anymore, but check if sk_wmem_alloc
reached 0 to perform the final freeing.
Drawback is that a skb->truesize error could lead to unfreeable sockets, or
even worse, prematurely calling __sk_free() on a live socket.
Nice speedups on SMP. tbench for example, going from 2691 MB/s to 2711 MB/s
on my 8 cpu dev machine, even if tbench was not really hitting sk_refcnt
contention point. 5 % speedup on a UDP transmit workload (depends
on number of flows), lowering TX completion cpu usage.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current conntrack code kills the ICMP conntrack entry as soon as
the first reply is received. This is incorrect, as we then see only
the first ICMP echo reply out of several possible duplicates as
ESTABLISHED, while the rest will be INVALID. Also this unnecessarily
increases the conntrackd traffic on H-A firewalls.
Make all the ICMP conntrack entries (including the replied ones)
last for the default of nf_conntrack_icmp{,v6}_timeout seconds.
Signed-off-by: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The lock "protects" an assignment and a comparision of an integer.
When the caller of device_cmp() evaluates the result, nat->masq_index
may already have been changed (regardless if the lock is there or not).
So, the lock either has to be held during nf_ct_iterate_cleanup(),
or can be removed.
This does the latter.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
ip_mc_drop_socket() method is declared in linux/igmp.h, which
is included anyhow in af_inet.c. So there is no need for this declaration.
This patch removes it from af_inet.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb
Delete skb->rtable field
Setting rtable is not allowed, just set dst instead as rtable is an alias.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplifies the conntrack event caching system by removing
several events:
* IPCT_[*]_VOLATILE, IPCT_HELPINFO and IPCT_NATINFO has been deleted
since the have no clients.
* IPCT_COUNTER_FILLING which is a leftover of the 32-bits counter
days.
* IPCT_REFRESH which is not of any use since we always include the
timeout in the messages.
After this patch, the existing events are:
* IPCT_NEW, IPCT_RELATED and IPCT_DESTROY, that are used to identify
addition and deletion of entries.
* IPCT_STATUS, that notes that the status bits have changes,
eg. IPS_SEEN_REPLY and IPS_ASSURED.
* IPCT_PROTOINFO, that reports that internal protocol information has
changed, eg. the TCP, DCCP and SCTP protocol state.
* IPCT_HELPER, that a helper has been assigned or unassigned to this
entry.
* IPCT_MARK and IPCT_SECMARK, that reports that the mark has changed, this
covers the case when a mark is set to zero.
* IPCT_NATSEQADJ, to report that there's updates in the NAT sequence
adjustment.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After some discussion offline with Christoph Lameter and David Stevens
regarding multicast behaviour in Linux, I'm submitting a slightly
modified patch from the one Christoph submitted earlier.
This patch provides a new socket option IP_MULTICAST_ALL.
In this case, default behaviour is _unchanged_ from the current
Linux standard. The socket option is set by default to provide
original behaviour. Sockets wishing to receive data only from
multicast groups they join explicitly will need to clear this
socket option.
Signed-off-by: Nivedita Singhvi <niv@us.ibm.com>
Signed-off-by: Christoph Lameter<cl@linux.com>
Acked-by: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somewhat luckily, I was looking into these parts with very fine
comb because I've made somewhat similar changes on the same
area (conflicts that arose weren't that lucky though). The loop
was very much overengineered recently in commit 915219441d
(tcp: Use SKB queue and list helpers instead of doing it
by-hand), while it basically just wants to know if there are
skbs after 'skb'.
Also it got broken because skb1 = skb->next got translated into
skb1 = skb1->next (though abstracted) improperly. Note that
'skb1' is pointing to previous sk_buff than skb or NULL if at
head. Two things went wrong:
- We'll kfree 'skb' on the first iteration instead of the
skbuff following 'skb' (it would require required SACK reneging
to recover I think).
- The list head case where 'skb1' is NULL is checked too early
and the loop won't execute whereas it previously did.
Conclusion, mostly revert the recent changes which makes the
cset very messy looking but using proper accessor in the
previous-like version.
The effective changes against the original can be viewed with:
git-diff 915219441d566f1da0caa0e262be49b666159e17^ \
net/ipv4/tcp_input.c | sed -n -e '57,70 p'
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipgre_tunnel_xmit() might need skb->dst, so tell dev_hard_start_xmit()
to no release it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipip_tunnel_xmit() might need skb->dst, so tell dev_hard_start_xmit()
to no release it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
roel kluin