This driver has been mostly rewritten since Michael Brown's initial
work, so swap the order of the authors.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor PHY, MAC and NIC configuration operations so that the
existing link configuration can be re-pushed with:
efx->phy_op->reconfigure(efx);
efx->mac_op->reconfigure(efx);
and a new configuration with:
efx->nic_op->reconfigure_port(efx);
(plus locking and error-checking).
We have not held the link settings in software (aside from flow
control), and have relied on asking the hardware what they are. This
is a problem because in some cases the hardware may no longer be in a
state to tell us. In particular, if an entire multi-port board is
reset through one port, the driver bindings to other ports have no
chance to save settings before recovering.
We only actually need to keep track of the autonegotiation settings,
so add an ethtool advertising mask to struct efx_nic, initialise it
in PHY init and update it as necessary.
Remove now-unneeded uses of efx_phy_op::{get,set}_settings() and
struct ethtool_cmd.
Much of this was done by Steve Hodgson <shodgson@solarflare.com>.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Only the XMAC on Falcon needs help from the driver to poll and reset
the MAC-PHY link (XAUI); GMII is a simple parallel bus and on later
NICs firmware takes care of the XAUI link. Also, an XMAC interrupt
currently schedules a work item which simply clears a flag
(efx_nic::mac_up) to be checked by the regular monitor (or the next
link reconfiguration, if that is sooner).
Rename the flag to xmac_poll_required, changing its sense. Remove the
needless indirection and just set the flag immediately. Call
falcon_xmac_poll() directly where required.
Add a new generic operation mac_op::check_fault to check the link
outside of regular monitoring, as required during self-tests.
(Note that this leaves us with an unused work item, but we will
immediately have another use for it.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Currently we initiate MAC stats DMA and busy-wait for completion when
stats are requested. We can improve on this with a periodic timer to
initiate and poll for stats, and opportunistically poll when stats are
requested.
Since efx_nic::stats_disable_count and efx_stats_{disable,enable}()
are Falcon-specific, rename them and move them accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we're at it, use type suffixes of 'd', 'q' and 'o', consistent
with register type names.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena is still based on the Falcon hardware architecture and will
share many of these definitions, so replace falcon_hwdefs.h with
regs.h.
The new definitions have been generated according to a naming
convention which incorporates the type and revision information.
Update the code accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
MAC, PHY and board events may be separately enabled and signalled.
Our current arrangement of chaining the polling functions can result
in events being missed. Change them to be more independent.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure for auto-negotiation of speed, duplex and flow
control.
When using 10Xpress, auto-negotiate flow control. While we're
at it, clean up the code to warn when partner is not 10GBASE-T
capable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFC4000 has a separate MAC for use at sub-10G speeds. Introduce
an efx_mac_operations structure with implementations for the two MACs.
Switch between the MACs as necessary.
PHY settings are independent of the MAC, so add get_settings() and
set_settings() to efx_phy_operations. Also add macs field to indicate
which MACs the PHY is connected to.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings