These CM_AUTOIDLE bits are now set by the clock code via the common PM
code in mach-omap2/pm.c.
N.B.: The pm24xx.c code that this patch removes didn't ensure that the
CM_AUTOIDLE bits were set for several 2430-only modules, such as
GPIO5, MDM_INTC, MMCHS1/2, the modem oscillator clock, and USBHS.
Similarly, the pm34xx.c code that this patch removes didn't ensure
that the CM_AUTOIDLE bits were set for USIM and the AM3517 UART4.
Those cases should now be handled.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Attempt to enable autoidle for as many clocks as possible in the
OMAP2+-common CONFIG_OMAP_RESET_CLOCKS code. Currently, this only
enables DPLL autoidle for OMAP3/4 DPLLs; but future patches will
enable autoidle for other clocks and the OMAP2 DPLL/APLLs.
In the long run, we should probably get rid of
CONFIG_OMAP_RESET_CLOCKS, and unconditionally run the code that it
selects. Otherwise, the state of the clock tree won't match the
hardware state - this could result in clocks being enabled or disabled
unpredictably.
Based on a patch by Rajendra Nayak <rnayak@ti.com> that did this in
the pm34xx.c/pm44xx.c code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Define the following architecture specific funtions for omap2/3/4
.clkdm_allow_idle
.clkdm_deny_idle
Convert the platform-independent framework to call these functions.
Also rename the api's by removing the omap2_ preamble.
Hence call omap2_clkdm_allow_idle as clkdm_allow_idle and
omap2_clkdm_deny_idle as clkdm_deny_idle.
Make the _clkdm_add_autodeps and _clkdm_del_autodeps as non-static
so they can be accessed from OMAP2/3 platform specific code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Define the following architecture specific funtions for omap2/3/4
.clkdm_sleep
.clkdm_wakeup
Convert the platform-independent framework to call these functions.
Also rename the api's by removing the omap2_ preamble.
Hence call omap2_clkdm_wakeup as clkdm_wakeup and
omap2_clkdm_sleep as clkdm_sleep.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: fixed omap3_clkdm_clear_all_sleepdeps() and
omap2_clkdm_clear_all_wkdeps() to test against the correct
loop termination condition; thanks to Kevin Hilman for finding and
helping fix]
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently, on HS/EMU devices, MPU power state forced to on during PM
init by the save secure RAM code. Rather than forcing the state of
MPU powerdomain to on, simply read the current value and restore it
after the ROM code has run.
This only affects the !CPUidle case since when CPUidle is enabled, the
MPU power state is dynamically changed by CPUidle. In the !CPUidle
case, MPU power state is initialized once at init and never touched.
Acked-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
Move the padconf save code from pm34xx.c to the System Control Module
code in mach-omap2/control.c. This is part of the general push to
move direct register access from middle-layer core code to low-level
core code, so the middle-layer code can be abstracted to work on
multiple platforms and cleaned up.
In the medium-to-long term, this code should be called by the mux
layer code, not the PM idle code. This is because, according to the
TRM, saving the padconf only needs to be done when the padconf
changes[1].
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
1. OMAP34xx Multimedia Device Silicon Revision 3.1.x [Rev. ZH] [SWPU222H]
Section 4.11.4 "Device Off-Mode Sequences"
The OMAP powerdomain code and data is all OMAP2+-specific. This seems
unlikely to change any time soon. Move plat-omap/include/plat/powerdomain.h
to mach-omap2/powerdomain.h. The primary point of doing this is to remove
the temptation for unrelated upper-layer code to access powerdomain code
and data directly.
As part of this process, remove the references to powerdomain data
from the GPIO "driver" and the OMAP PM no-op layer, both in plat-omap.
Change the DSPBridge code to point to the new location for the
powerdomain headers. The DSPBridge code should not be including the
powerdomain headers; these should be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
The OMAP clockdomain code and data is all OMAP2+-specific. This seems
unlikely to change any time soon. Move plat-omap/include/plat/clockdomain.h
to mach-omap2/clockdomain.h. The primary point of doing this is to remove
the temptation for unrelated upper-layer code to access clockdomain code
and data directly.
DSPBridge also uses the clockdomain headers for some reason, so,
modify it also. The DSPBridge code should not be including the
clockdomain headers; these should be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Now that OMAP4-specific PRCM functions have been added, distinguish the
existing OMAP2/3-specific PRCM functions by prefixing them with "omap2_".
This patch should not result in any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
The OMAP3 PRM module is in the WKUP powerdomain, which is always
powered when the chip is powered, so it shouldn't be necessary to save
and restore those PRM registers. Remove the PRM register save/restore
code, which should save several microseconds during off-mode
entry/exit, since PRM register accesses are relatively slow.
While doing so, move the CM register save/restore code into
CM-specific code. The CM module has been distinct from the PRM module
since 2430.
This patch includes some minor changes to pm34xx.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
In preparation for adding OMAP4-specific PRCM accessor/mutator
functions, split the existing OMAP2/3 PRCM code into OMAP2/3-specific
files. Most of what was in mach-omap2/{cm,prm}.{c,h} has now been
moved into mach-omap2/{cm,prm}2xxx_3xxx.{c,h}, since it was
OMAP2xxx/3xxx-specific.
This process also requires the #includes in each of these files to be
changed to reference the new file name. As part of doing so, add some
comments into plat-omap/sram.c and plat-omap/mcbsp.c, which use
"sideways includes", to indicate that these users of the PRM/CM includes
should not be doing so.
Thanks to Felipe Contreras <felipe.contreras@gmail.com> for comments on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Errata covered:
- 1.157 & 1.185
- i443
- i581
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Limitation i583: Self_Refresh Exit issue after OFF mode
Issue:
When device is waking up from OFF mode, then SDRC state machine sends
inappropriate sequence violating JEDEC standards.
Impact:
OMAP3630 < ES1.2 is impacted as follows depending on the platform:
CS0: for 38.4MHz as internal sysclk, DDR content seen to be stable, while
for all other sysclk frequencies, varied levels of instability
seen based on varied parameters.
CS1: impacted
This patch takes option #3 as recommended by the Silicon erratum:
Avoid core power domain transitioning to OFF mode. Power consumption
impact is expected in this case.
To do this, we route core OFF requests to RET request on the impacted
revisions of silicon.
Acked-by: Jean Pihet <j-pihet@ti.com>
[nm@ti.com: rebased the code to 2.6.37-rc2- short circuit code changed a bit]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently omap3_cpuidle_update_states makes whole sale decision
on which C states to update based on enable_off_mode variable
Instead, achieve the same functionality by independently providing
mpu and core deepest states the system is allowed to achieve and
update the idle states accordingly.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[khilman: fixed additional user of this API in OMAP CPUidle driver]
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
While coming out of MPU OSWR/OFF states, L2 controller is reseted.
The reset behavior is implementation specific as per ARMv7 TRM and
hence $L2 needs to be invalidated before it's use. Since the
AUXCTRL register is also reconfigured, disable L2 cache before
invalidating it and re-enables it afterwards. This is as per
Cortex-A8 ARM documentation.
Currently this is identified as being needed on OMAP3630 as the
disable/enable is done from "public side" while, on OMAP3430, this
is done in the "secure side".
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: ported to 2.6.37-rc2, added hooks to enable the logic only on 3630]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Erratum id: i608
RTA (Retention Till Access) feature is not supported and leads to device
stability issues when enabled. This impacts modules with embedded memories
on OMAP3630
Workaround is to disable RTA on boot and coming out of core off.
For disabling RTA coming out of off mode, we do this by overriding the
restore pointer for 3630 as the first point of entry before caches are
touched and is common for GP and HS devices. To disable earlier than
this could be possible by modifying the PPA for HS devices, but not for
GP devices.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[ambresh@ti.com: co-developer]
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Introduce errata handling for OMAP3. This patch introduces
errata variable and stub for initialization which will be
filled up by follow-on patches.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Some bad interaction between the idle and the suspend paths has been
identified: the idle code is called during the suspend enter and exit
sequences. This could cause corruption or lock-up of resources.
The solution is to move the calls to disable_hlt at the very beginning
of the suspend sequence (ex. in omap3_pm_begin instead of
omap3_pm_prepare), and the call to enable_hlt at the very end of
the suspend sequence (ex. in omap3_pm_end instead of omap3_pm_finish).
Tested with RET and OFF on Beagle and OMAP3EVM.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
commit 0d8e2d0dad (OMAP2+: PM/serial:
hold console semaphore while OMAP UARTs are disabled) added use of the
console semaphore to protect UARTs from being accessed after disabled
during idle, but this causes problems in suspend.
During suspend, the console semaphore is acquired by the console
suspend method (console_suspend()) so the try_acquire_console_sem()
will always fail and suspend will be aborted.
To fix, introduce a check so the console semaphore is only attempted
during idle, and not during suspend. Also use the same check so that
the console semaphore is not prematurely released during resume.
Thanks to Paul Walmsley for suggesting adding the same check during
resume.
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Tested-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The console semaphore must be held while the OMAP UART devices are
disabled, lest a console write cause an ARM abort (and a kernel crash)
when the underlying console device is inaccessible. These crashes
only occur when the console is on one of the OMAP internal serial
ports.
While this problem has been latent in the PM idle loop for some time,
the crash was not triggerable with an unmodified kernel until commit
6f251e9db1 ("OMAP: UART: omap_device
conversions, remove implicit 8520 assumptions"). After this patch, a
console write often occurs after the console UART has been disabled in
the idle loop, crashing the system. Several users have encountered
this bug:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg38396.htmlhttp://www.mail-archive.com/linux-omap@vger.kernel.org/msg36602.html
The same commit also introduced new code that disabled the UARTs
during init, in omap_serial_init_port(). The kernel will also crash
in this code when earlyconsole and extra debugging is enabled:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg36411.html
The minimal fix for the -rc series is to hold the console semaphore
while the OMAP UARTs are disabled. This is a somewhat overbroad fix,
since the console may not be located on an OMAP UART, as is the case
with the GPMC UART on Zoom3. While it is technically possible to
determine which devices the console or earlyconsole is actually
running on, it is not a trivial problem to solve, and the code to do
so is not really appropriate for the -rc series.
The right long-term fix is to ensure that no code outside of the OMAP
serial driver can disable an OMAP UART. As I understand it, code to
implement this is under development by TI.
This patch is a collaboration between Paul Walmsley <paul@pwsan.com>
and Tony Lindgren <tony@atomide.com>. Thanks to Ming Lei
<tom.leiming@gmail.com> and Pramod <pramod.gurav@ti.com> for their
feedback on earlier versions of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Pramod <pramod.gurav@ti.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 914bab936fe0388a529079679e2f137aa4ff548d (OMAP: mach-omap2: Fix
incorrect assignment warnings) changed a pointer from 'u32 *' to
'void *' without also fixing up the pointer arithmetic.
Fix the scratchpad offsets so they are byte offsets instead of
word offsets and thus work correctly with a void pointer base.
Special thanks to Jean Pihet for taking the time track down this
problem and propose an initial solution.
Tested with off-idle and off-suspend on 36xx/Zoom3 and 34xx/omap3evm.
Cc: Manjunath Kondaiah G <manjugk@ti.com>
Reported-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap. This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.
In response, move the SCM headers into mach-omap2/.
As part of this, remove the direct SCM access from the OMAP UDC
driver. It was clearly broken. The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Add prepare idle and resume idle call for uart4 used by 3630.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
To standarize among other uarts (1 to 3), we shall now:
- Enable uart4 autodile bit.
- Enable uart4 wakeup in PER.
- Allow uart4 to wakeup the MPU.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When the clockdomain layer initializes, place all clockdomains into
software-supervised mode, and clear all wakeup and sleep dependencies
immediately, rather than waiting for the PM code to do this later.
This fixes a major bug where critical sleep dependencies added by the
hwmod code are cleared during late PM init.
As a side benefit, the _init_{wk,sleep}dep_usecount() functions are no
longer needed, so remove them.
Kevin Hilman <khilman@deeprootsystems.com> did all the really hard work on
this, identifying the problem and finding the bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The set_pwrdm_state() is needed on omap4 as well so move
this routine to common pm.c file so that it's available for omap3/4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch moves omap2_pm_wakeup_on_timer() and pm debug entries
form pm34xx.c to pm-debug.c and export it, so that it is available
to other OMAPs
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In an effort to simplify the core idle path, move any device-specific
special case handling from the core PM idle path into the CPUidle
pre-idle checking path.
This keeps the core, interrupts-disabled idle path streamlined and
independent of any device-specific handling, and also allows CPUidle
to do the checking only for certain C-states as needed. This patch
has the device checks in place for all states with the CHECK_BM flag,
namely all states >= C2.
This patch was inspired by a similar patch written by Tero Kristo as
part of a larger series to add INACTIVE state support.
NOTE: This is a baby-step towards decoupling device idle (or system
idle) from CPU idle. Eventually, CPUidle should only manage the CPU,
and device/system idle should be managed elsewhere.
Cc: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes omap3 hardcodings from pm-debug.c
so that enabling PM debugfs support does break compilation
for other OMAP's. This is a preparatory patch for supporting
OMAP4 pm entries through PM debugfs.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cleanup indentation around IO wakeup enable, the '\' terminator is
not required in C when wrapping an expression past end-of-line.
Whitespace change only.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Commit 5a5f561 (convert OMAP3 PRCM macros to the _SHIFT/_MASK suffixes)
mistakenly removed the check for PER when disabling the IO chain.
During idle, if the PER powerdomain transitions into a lower state
and CORE does not, the IO pad wakeups are not being disabled in
the idle path after they are enabled. This can happen with the
lower C-states when using CPUidle for example.
This patch ensures that the check for disabling IO wakeups also checks
for PER transitions, matching the check done to enable IO wakeups.
Found when debugging PM/CPUidle related problems reported by Ameya
Palande <ameya.palande@nokia.com>. Problems were triggered
particularily on boards with UART2 consoles (n900, Overo) since UART2
is in the PER powerdomain.
Tested on l-o master (omap3_defonfig + CONFIG_CPU_IDLE=y) as well
as with current PM branch. Boards tested: n900, Overo, omap3evm.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Ameya Palande <ameya.palande@nokia.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated description to clarify the transistion]
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3505/3517 doesn't have IO wakeup capability, so we do not need to set
the bit OMAP3430_EN_IO and the bit OMAP3430_EN_IO_CHAIN in the register
PM_WKEN_WKUP when the system enters suspend state.
Tested on AM3517EVM and OMAP3530EVM.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Checking to se if the IO daisy chain is enabled should be checking the
PM_WKEN register, not the PM_WKST register. Reading PM_WKST tells us
if an event occurred, not whether or not it is enabled.
Apparently, we've been lucky until now in that a pending event has not
been there during enable. However, on 3630/Zoom3, I noticed because
of the WARN that this timeout was always happening.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Writes to the PM_*GRPSEL registers should use _GRPSEL_ macros, not _EN_ macros,
to match the TRM and guard against inadvertent error. This patch should
not cause any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>
Fix all of the remaining PRCM register shift/bitmask macros that did not
use the _SHIFT/_MASK suffixes to use them. This makes the use of these
macros consistent. It is intended to reduce error, as code can be inspected
visually by reviewers to ensure that bitshifts and bitmasks are used in
the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Fix all of the remaining OMAP3 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Currently, the GPIO 'prepare' hook is only called when going to
off-mode, while the function is called 'prepare_for_retention.' This
patch renames the function to 'prepare_for_idle' and calls it for any
powersate != PWRDM_POWER_ON passing in the powerstate.
The hook itself is then responsible for doing various preparation
based on the powerstate.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Off mode is now using the omap2 retention fix code for scanning GPIOs
during off-mode transitions. All the *non_wakeup_gpios variables
are now used for off-mode transition tracking on OMAP3. This patch fixes
cases where GPIO state changes are missed during off-mode.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
We can remove this wakeup dependency since now, when
GPIO2-6 are enabled for IO-pad wakeup, PER domain is gauranteed
to be awake or be woken up to service.
The previous dependency did not handle all corner cases. Since there
was no sleep dependency between CORE and PER domains, if PER enters
RET and CORE is ON, PER will not be active for GPIO handling.
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
IO events can also come from GPIO modules, which reside in the PER domain.
It is possible for the PER to enter RET while CORE is still in ON.
If GPIO 2-6 are enabled for IO-pad wakeups, the PER domain will not
wakeup in this case, unless we enable it.
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Millisecond resolution is possible and there are use cases for it
(automatic testing).
Seconds-based interface is preserved for compatibility.
Signed-off-by: Ari Kauppi <Ext-Ari.Kauppi@nokia.com>
Reviewed-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
While handling PRCM IRQs, mask out interrupts that are not enabled in
PRM_IRQENABLE_MPU. If these are not masked out, non-enabled
interrupts are caught, a WARN() is printed due to no 'handler' and the
events are cleared. In addition to being noisy, this can also
interfere with independent polling of this register by SR/VP code.
This was noticed using SmartReflex transitions which cause the VPx_*
interrupts to be handled since they are set in PRM_IRQSTATUS_MPU even
but not enabled in PRM_IRQENABLE_MPU.
Acked-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Paul Walmsley