Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bosch M_CAN is CAN FD capable device. This patch implements the CAN
FD features include up to 64 bytes payload and bitrate switch function.
1) Change the Rx FIFO and Tx Buffer to 64 bytes for support CAN FD
up to 64 bytes payload. It's backward compatible with old 8 bytes
normal CAN frame.
2) Allocate can frame or canfd frame based on EDL bit
3) Bitrate Switch function is disabled by default and will be enabled
according to CANFD_BRS bit in cf->flags.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The spec mentions there may be a delay until the value written to INIT can be
read back due to the synchronization mechanism between the two clock domains.
But it does not indicate the exact clock cycles needed. The 5us delay is a
test value and seems ok.
Without the delay, CCCR.CCE bit may fail to be set and then the initialization
fail sometimes when do repeatly up and down.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The original code missed to set the cf->can_dlc in the RTR case, so add it.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The M_CAN message RAM is usually equipped with a parity or ECC functionality.
But RAM cells suffer a hardware reset and can therefore hold arbitrary content
at startup - including parity and/or ECC bits.
To prevent the M_CAN controller detecting checksum errors when reading
potentially uninitialized TX message RAM content to transmit CAN frames the TX
message RAM has to be written with (any kind of) initial data.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can uses io memory which makes it not compilable on architectures
without HAS_IOMEM such as UML:
drivers/built-in.o: In function `m_can_plat_probe':
m_can.c:(.text+0x218cc5): undefined reference to `devm_ioremap_resource'
m_can.c:(.text+0x218df9): undefined reference to `devm_ioremap'
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The variable err was of the type u32. It was being compared with < 0, and being
an unsigned variable the comparison would have been always false.
Moreover, err was getting the return value from set_reset_mode() and
xcan_set_bittiming(), and both are returning int.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
these variable were only assigned some values, but then never
reused again.
so they are safe to be removed.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It seems struct esd_usb2 dev is not deallocated on disconnect. The patch adds
the missing deallocation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes a typo in CAN's dev.c:
CIA -> CiA
which stands for CAN in Automation.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
AM4372 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for it. The driver data is same as AM3352
but this gives us flexibility to add AM4372 specific quirks
if required later.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
AM3352 SoC has 2 DCAN modules. Add compatible id and
raminit driver data for am3352 DCAN.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
DRA7 SoC has 2 CAN IPs. Provide compatible IDs and RAMINIT
register data for both.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
DRA7 CAN IP suffers from a problem which causes it to be prevented
from fully turning OFF (i.e. stuck in transition) if the module was
disabled while there was traffic on the CAN_RX line.
To work around this issue we select the SLEEP pin state by default
on probe and use the DEFAULT pin state on CAN up and back to the
SLEEP pin state on CAN down.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some SoCs e.g. (TI DRA7xx) need a START pulse to start the
RAMINIT sequence i.e. START bit must be set and cleared before
checking for the DONE bit status.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some TI SoCs like DRA7 have a RAMINIT register specification
different from the other AMxx SoCs and as expected by the
existing driver.
To add more insanity, this register is shared with other
IPs like DSS, PCIe and PWM.
Provides a more generic mechanism to specify the RAMINIT
register location and START/DONE bit position and use the
syscon/regmap framework to access the register.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some platforms (e.g. TI) need special RAMINIT register handling.
Provide a way to store RAMINIT register description in driver data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We want to have more data than just can_dev_id to be present
in the driver data e.g. TI platforms need RAMINIT register
description. Introduce the c_can_driver_data structure and move
the can_dev_id into it.
Tidy up the way it is used on probe().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
TI's RAMINIT DONE mechanism is buggy on AM43xx SoC and may not always
be set after the START bit is set. Although it seems to work fine even
in that case. So add a timeout mechanism to c_can_hw_raminit_wait_ti().
Don't bail out in that failure case but just print an error message.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CAN_AT91 needs HAS_IOMEM, so depends on it. The related error (with
allmodconfig under um):
CC [M] drivers/net/can/at91_can.o
drivers/net/can/at91_can.c: In function ‘at91_can_probe’:
drivers/net/can/at91_can.c:1329:2: error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration]
addr = ioremap_nocache(res->start, resource_size(res));
^
drivers/net/can/at91_can.c:1329:7: warning: assignment makes pointer from integer without a cast [enabled by default]
addr = ioremap_nocache(res->start, resource_size(res));
^
drivers/net/can/at91_can.c:1384:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(addr);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make the driver work with the common clock framework, this patch
converts the clk_enable()/clk_disable() to
clk_prepare_enable()/clk_disable_unprepare(). While there, add the missing
error handling.
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
Signed-off-by: Anthony Harivel <anthony.harivel@emtrion.de>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch increases the mask in the FLEXCAN_MCR_MAXMB() to 7 bits as in the
newer flexcan cores the MAXMB field is 7 bits wide.
Reported-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After sending a RTR frame the TX mailbox becomes a RX_EMPTY mailbox. To avoid
side effects when the RX-FIFO is full, this patch puts the TX mailbox into
TX_INACTIVE mode in the transmission complete interrupt handler. This, of
course, leaves a race window between the actual completion of the transmission
and the handling of tx-complete interrupt. However this is the best we can do
without busy polling the tx complete interrupt.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch implements the workaround mentioned in ERR005829:
ERR005829: FlexCAN: FlexCAN does not transmit a message that is enabled to
be transmitted in a specific moment during the arbitration process.
Workaround: The workaround consists of two extra steps after setting up a
message for transmission:
Step 8: Reserve the first valid mailbox as an inactive mailbox (CODE=0b1000).
If RX FIFO is disabled, this mailbox must be message buffer 0. Otherwise, the
first valid mailbox can be found using the "RX FIFO filters" table in the
FlexCAN chapter of the chip reference manual.
Step 9: Write twice INACTIVE code (0b1000) into the first valid mailbox.
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Apparently mailboxes may contain random data at startup, causing some of them
being prepared for message reception. This causes overruns being missed or even
confusing the IRQ check for trasmitted messages, increasing the transmit
counter instead of the error counter.
This patch initializes all mailboxes after the FIFO as RX_INACTIVE.
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the initialization of the TX mailbox. It is now correctly
initialized as TX_INACTIVE not RX_EMPTY.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add PCI ID definition for the single channel PCAN ExpressCard 34 adapter. Due
to the subsystem id evaluation the correct number of channels (here 1) is
created at initialization time. Tested including the LED functionality.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pass the correct 'mask' and 'value' bits to c_can_hw_raminit_wait_ti(). They
seem to have been swapped in the usage instances.
Reported-by: Jay Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Apparently can_restart() runs from a (timer-) interrupt and can call
flexcan_chip_[en|dis]able(), so avoid using usleep_range()
Signed-off-by: David Jander <david@protonic.nl>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Once the CAN-bus is open and a packet is sent, the controller switches
into the PASSIVE state. Once the BUS is closed again it goes the back
err-warning. The TX error counter goes 0 -> 0x80 -> 0x7f.
This patch makes sure that the user learns about this state chang
(CAN_STATE_ERROR_WARNING => CAN_STATE_ERROR_PASSIVE)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Matthias Klein <matthias.klein@optimeas.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case we don't have FLEXCAN_HAS_BROKEN_ERR_STATE and the user set
CAN_CTRLMODE_BERR_REPORTING once it can not be unset again until reboot.
So in case neither hardware nor user wants the error interrupt disable
the bit.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
devm_ioremap() returns NULL on error, not an ERR_PTR().
Fixes: 33cf756569 ('can: c_can_platform: Fix raminit, use devm_ioremap() instead of devm_ioremap_resource()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When sja1000 is not compiled as module the SJA1000 chip is only
initialized during device registration on kernel boot. Should the chip
get a hardware reset there is no way to reinitialize it without re-
booting the Linux kernel.
This patch adds a check in sja1000_start if the chip is initialized, if
not we initialize it.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch moves the data allocated using dma_alloc_coherent to the
corresponding managed interface and does away with the calls to free the
allocated memory in the probe and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
this patch removes best_rate variable from can_calc_bittiming()
function which was set but was never used.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support of the device tree probing for the Renesas R-Car CAN controllers.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When writing the driver, I didn't give enough attention to the possible sources
of the CAN clock: although the value of the CLKR register was specified by the
platform data, the driver only handled one case, that is CAN clock being
sourced from the clkp1 clock, the same that clocks the whole CAN module. In
order to fix that overlook, we'll have to handle the CAN clock separately from
the peripheral clock (however, clkp1 will be specified for a CAN device only
once)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The patch adds the basic CAN TX/RX function support for Bosch M_CAN controller.
For TX, only one dedicated tx buffer is used for sending data.
For RX, RXFIFO 0 is used for receiving data to avoid overflow.
Rx FIFO 1 and Rx Buffers are not used currently, as well as Tx Event FIFO.
Due to the message ram can be shared by multi m_can instances
and the fifo element is configurable which is SoC dependant,
the design is to parse the message ram related configuration data from device
tree rather than hardcode define it in driver which can make the message
ram sharing fully transparent to M_CAN controller driver,
then we can gain better driver maintainability and future features upgrade.
M_CAN also supports CANFD protocol features like data payload up to 64 bytes
and bitrate switch at runtime, however, this patch still does not add the
support for these features.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[mkl: Squahed semicolon cleanup by Fengguang Wu]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Extend FlexCAN driver to support Vybrid. Vybrids variant of the IP
has ECC support which is controlled through the memory error
control register (MECR). There is also an errata which leads to
false positive error detections (ID e5295). This patch disables
the memory error detection completely.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The funcion flexcan_get_berr_counter() may be called from userspace even if the
interface is down, this the clocks are disabled. This patch switches on the
clocks before accessing the ecr register.
Reported-by: Ashutosh Singh <ashuleapyear@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
No need to manually copy debug settings into subdir Makefiles. kbuild
has a mechanism for inheriting, so let's use it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David S. Miller