The rework of the command handling in the nand driver
led to wrong address setting in the command control
function. Use the correct address again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert the use of printk() to the correct dev_info/dev_err
functions
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The oob fixups broke a return value and missed one patch from
the Mailing List.
Signed-off-by: Savin Zlobec <savin@epico.si>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Following problems are addressed:
- wrong status caused early break out of nand_wait()
- removed the bogus status check in nand_wait() which
is a relict of the abandoned support for interrupted
erase.
- status check moved to the correct place in read_oob
- oob support for syndrom based ecc with strange layouts
- use given offset in the AUTOOOB based oob operations
Partially based on a patch from Vitaly Vool <vwool@ru.mvista.com>
Thanks to Savin Zlobec <savin@epico.si> for tracking down the
status problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In nand_read_page_syndrome/nand_write_page_syndrome the calculation of
the remaining oob length which is not used by the prepad/ecc/postpad
areas is wrong.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix unused variables and commenting since tglx's
new NAND updates
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Let's not attempt the abolition of mtd->type until/unless it's properly
thought through. And certainly, let's not do it by halves.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fallout from the incoming 64-bit-resource stuff:
drivers/mtd/maps/physmap.c: In function 'physmap_flash_probe':
drivers/mtd/maps/physmap.c:94: warning: format '%.8lx' expects type 'long
unsigned int', but argument 2 has type 'resource_size_t'
drivers/mtd/maps/physmap.c:94: warning: format '%.8lx' expects type 'long
unsigned int', but argument 3 has type 'resource_size_t'
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
mtdchar.c direcly copied part of struct mtd_info to userspace, thereby
implicitly making it part of the ABI. With this patch, struct
mtd_info is independent of the ABI and can have its fields removed,
reordered, etc.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
Ram devices get the extra capability of MTD_NO_ERASE - not requiring
an explicit erase before writing to it. Currently only mtdblock uses
this capability. Rest of the patch is a simple text replacement.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
No mtd user should ever check for the device type. Instead, device features
should be checked by the flags - if at all.
As a first step towards type removal, change MTD_ROM into MTD_GENERIC_TYPE.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
drivers/mtd/nand/nand_base.c: In function 'nand_transfer_oob':
drivers/mtd/nand/nand_base.c:909: warning: comparison of distinct pointer types lacks a cast
drivers/mtd/nand/nand_base.c: In function 'nand_do_read_oob':
drivers/mtd/nand/nand_base.c:1097: error: 'len' undeclared (first use in this function)
drivers/mtd/nand/nand_base.c:1097: error: (Each undeclared identifier is reported only once
drivers/mtd/nand/nand_base.c:1097: error: for each function it appears in.)
drivers/mtd/nand/nand_base.c: In function 'nand_fill_oob':
drivers/mtd/nand/nand_base.c:1411: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The raw read/write access to NAND (without ECC) has been changed in the
NAND rework. Expose the new way - setting the file mode via ioctl - to
userspace. Also allow to read out the ecc statistics information so userspace
tools can see that bitflips happened and whether errors where correctable
or not. Also expose the number of bad blocks for the partition, so nandwrite
can check if the data fits into the parition before writing to it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Return -EUCLEAN on read when a bitflip was detected and corrected, so the
clients can react and eventually copy the affected block to a spare one.
Make all in kernel users aware of the change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hopefully the last iteration on this!
The handling of out of band data on NAND was accompanied by tons of fruitless
discussions and halfarsed patches to make it work for a particular
problem. Sufficiently annoyed by I all those "I know it better" mails and the
resonable amount of discarded "it solves my problem" patches, I finally decided
to go for the big rework. After removing the _ecc variants of mtd read/write
functions the solution to satisfy the various requirements was to refactor the
read/write _oob functions in mtd.
The major change is that read/write_oob now takes a pointer to an operation
descriptor structure "struct mtd_oob_ops".instead of having a function with at
least seven arguments.
read/write_oob which should probably renamed to a more descriptive name, can do
the following tasks:
- read/write out of band data
- read/write data content and out of band data
- read/write raw data content and out of band data (ecc disabled)
struct mtd_oob_ops has a mode field, which determines the oob handling mode.
Aside of the MTD_OOB_RAW mode, which is intended to be especially for
diagnostic purposes and some internal functions e.g. bad block table creation,
the other two modes are for mtd clients:
MTD_OOB_PLACE puts/gets the given oob data exactly to/from the place which is
described by the ooboffs and ooblen fields of the mtd_oob_ops strcuture. It's
up to the caller to make sure that the byte positions are not used by the ECC
placement algorithms.
MTD_OOB_AUTO puts/gets the given oob data automaticaly to/from the places in
the out of band area which are described by the oobfree tuples in the ecclayout
data structre which is associated to the devicee.
The decision whether data plus oob or oob only handling is done depends on the
setting of the datbuf member of the data structure. When datbuf == NULL then
the internal read/write_oob functions are selected, otherwise the read/write
data routines are invoked.
Tested on a few platforms with all variants. Please be aware of possible
regressions for your particular device / application scenario
Disclaimer: Any whining will be ignored from those who just contributed "hot
air blurb" and never sat down to tackle the underlying problem of the mess in
the NAND driver grown over time and the big chunk of work to fix up the
existing users. The problem was not the holiness of the existing MTD
interfaces. The problems was the lack of time to go for the big overhaul. It's
easy to add more mess to the existing one, but it takes alot of effort to go
for a real solution.
Improvements and bugfixes are welcome!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Most of those macros are unused and the used ones just obfuscate
the code. Remove them and fixup all users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The nand_oobinfo structure is not fitting the newer error correction
demands anymore. Replace it by struct nand_ecclayout and fixup the users
all over the place. Keep the nand_oobinfo based ioctl for user space
compability reasons.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The info structure for out of band data was copied into
the mtd structure. Make it a pointer and remove the ability
to set it from userspace. The position of ecc bytes is
defined by the hardware and should not be changed by software.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The platform structure was lacking an oobinfo field.
The NDFC driver had some remains from another tree.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We have a type pointer. Make use of it instead of the error prone nand_ids[i]
reference.
The NAND driver used to set default name settings from the chip ID
string for the device. The feature got lost during the rework. Add it back.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
nCE setting can be done when the first command is issued to the device.
We keep the deselect functionality as it makes sense to deassert nCE
when the device becomes idle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Modularize the write function and reorganaize the internal buffer
management. Remove obsolete chip options and fixup all affected
users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
PCI is faked on these devices by SMM traps. Don't depend on that --
check for the chipset directly instead.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Removing readv from struct mtd_info broke block2mtd. Remove the
reference and the useless default implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Split the core of the read function out and implement
seperate handling functions for software and hardware
ECC.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The nand driver has a superflous read ready / command
delay in the read functions. This was added to handle
chips which have an automatic read forward. Newer
chips do not have this functionality anymore. Add this
option to avoid the delay / I/O operation. Mark all
large page chips with the new option flag.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The lock simplifying patch did not move the lock and waitqueue
initialization into the controller allocation patch.
This reinitializes waitqueue and spinlocks also for driver
supplied controller stuctures. Move it into the allocation path.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The previous change of the command / hardware control allows to
remove the write_byte/word functions completely, as their only
user were nand_command and nand_command_lp.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The hwcontrol function enforced a step by step state machine
for any kind of hardware chip access. Let the hardware driver
know which control bits are set and inform it about a change
of the control lines. Let the hardware driver write out the
command and address bytes directly. This gives a peformance
advantage for address bus controlled chips and simplifies the
quirks in the hardware drivers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
MTD clients are agnostic of FLASH which needs ECC suppport.
Remove the functions and fixup the callers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
First step of modularizing ECC support.
- Move ECC related functionality into a seperate embedded data structure
- Get rid of the hardware dependend constants to simplify new ECC models
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner