Some Ricoh controllers only respect a full reset when there is no card in the
slot. As we wait for the reset to complete, we must avoid even requesting
those resets on the buggy controllers.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sprinkle some mmiowb() where needed (writeX() before unlock()).
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Cc: Daniel Qarras <dqarras@yahoo.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Driver for TI Flash Media card reader. At present, only MMC/SD cards are
supported.
[akpm@osdl.org: cleanups, build fixes]
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Cc: Daniel Qarras <dqarras@yahoo.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clarify my (Pierre's) position on which GPL versions apply. The patch only
touches the source files where I am the only major author. The people who
have made the minor commits to the files have been contacted and have no
issues with this change.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it possible to disable the block layer. Not all embedded devices require
it, some can make do with just JFFS2, NFS, ramfs, etc - none of which require
the block layer to be present.
This patch does the following:
(*) Introduces CONFIG_BLOCK to disable the block layer, buffering and blockdev
support.
(*) Adds dependencies on CONFIG_BLOCK to any configuration item that controls
an item that uses the block layer. This includes:
(*) Block I/O tracing.
(*) Disk partition code.
(*) All filesystems that are block based, eg: Ext3, ReiserFS, ISOFS.
(*) The SCSI layer. As far as I can tell, even SCSI chardevs use the
block layer to do scheduling. Some drivers that use SCSI facilities -
such as USB storage - end up disabled indirectly from this.
(*) Various block-based device drivers, such as IDE and the old CDROM
drivers.
(*) MTD blockdev handling and FTL.
(*) JFFS - which uses set_bdev_super(), something it could avoid doing by
taking a leaf out of JFFS2's book.
(*) Makes most of the contents of linux/blkdev.h, linux/buffer_head.h and
linux/elevator.h contingent on CONFIG_BLOCK being set. sector_div() is,
however, still used in places, and so is still available.
(*) Also made contingent are the contents of linux/mpage.h, linux/genhd.h and
parts of linux/fs.h.
(*) Makes a number of files in fs/ contingent on CONFIG_BLOCK.
(*) Makes mm/bounce.c (bounce buffering) contingent on CONFIG_BLOCK.
(*) set_page_dirty() doesn't call __set_page_dirty_buffers() if CONFIG_BLOCK
is not enabled.
(*) fs/no-block.c is created to hold out-of-line stubs and things that are
required when CONFIG_BLOCK is not set:
(*) Default blockdev file operations (to give error ENODEV on opening).
(*) Makes some /proc changes:
(*) /proc/devices does not list any blockdevs.
(*) /proc/diskstats and /proc/partitions are contingent on CONFIG_BLOCK.
(*) Makes some compat ioctl handling contingent on CONFIG_BLOCK.
(*) If CONFIG_BLOCK is not defined, makes sys_quotactl() return -ENODEV if
given command other than Q_SYNC or if a special device is specified.
(*) In init/do_mounts.c, no reference is made to the blockdev routines if
CONFIG_BLOCK is not defined. This does not prohibit NFS roots or JFFS2.
(*) The bdflush, ioprio_set and ioprio_get syscalls can now be absent (return
error ENOSYS by way of cond_syscall if so).
(*) The seclvl_bd_claim() and seclvl_bd_release() security calls do nothing if
CONFIG_BLOCK is not set, since they can't then happen.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Right now ->flags is a bit of a mess: some are request types, and
others are just modifiers. Clean this up by splitting it into
->cmd_type and ->cmd_flags. This allows introduction of generic
Linux block message types, useful for sending generic Linux commands
to block devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-mmc:
[MMC] Don't check READY_FOR_DATA when reading
[MMC] MMC_CAP_BYTEBLOCK flag for non-log2 block sizes capable hosts
[MMC] Add multi block-write capability
[MMC] Remove data->blksz_bits member
[MMC] Convert mmci to use data->blksz rather than data->blksz_bits
This is more preparation for adding support for the new Atmel AT91SAM9
processors.
Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The third argument of au1xxx_dbdma_chan_alloc's callback function is not
used anywhere.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no point checking to see if the card is ready to accept
data when we're reading from it - sending the command only wastes
precious bus bandwidth.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some MMC hosts can only handle log2 block sizes. Unfortunately,
the MMC password support needs to be able to send non-log2 block
sizes. Provide a capability so that the MMC password support can
decide whether it should use this support or not.
The unfortunate side effect of this host limitation is that any
MMC card protected by a password which is not a log2 block size
can not be accessed on a host which only allows a log2 block size.
This change just adds the flag. The MMC password support code
needs updating to use it (if and when it is finally submitted.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a capability flag for drivers to set when they can perform multi-
block transfers to cards _and_ correctly report the number of bytes
transferred should an error occur.
The last point is very important - if a driver reports more bytes than
were actually accepted by the card and an error occurs, there is the
possibility for data loss.
Pierre Ossman provided the patch for wbsd and sdhci.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both MMC and SD specifications specify (although a bit unclearly in
the MMC case) that a sector size of 512 bytes must always be
supported by the card.
Cards can report larger "native" size than this, and cards >= 2 GB
even must do so. Most other readers use 512 bytes even for these
cards. We should do the same to be compatible.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having two places which independently calculate the
timeout for data transfers, make it a library function instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Patch from Pavel Pisa
This is another approach to SDHC deficiency workaround.
It seems, that previous solution based on 16 bytes (FIFO length size)
read is still timing sensitive on genirq and fully preemptive kernels.
The new solution is backuped by M9328 UM statement, that only 512 byte
block are working properly and by 2.4.26 FreeScale's SDHC code.
Jay Monkman reports significant improvement on code based
on this driver after applying this change on MX21 as well.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Secure Digital cards use a different algorithm to calculate the timeout
for data transfers. Using the MMC one works often, but not always.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Another misuse of the global 'io' variable instead of the local 'base'.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There were some confusion about base I/O variables in the wbsd driver.
Seems like things have been working on shear luck so far. The global 'io'
variable (used when manually configuring the resources) was used instead of
the local 'base' variable.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Juha [l
When the block queue is plugged, mq->req must be set to NULL.
Otherwise mq->req might be left non-NULL, even though mmcqd is
not processing a request, thus preventing the MMC queue thread from
being woken up when new requests do arrive.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
O2 Micro's controllers have a larger specification version value and are
therefore denied by the driver. When bypassing this check they seem to work
fine. This patch makes the code a bit more forgiving by changing the error
to a warning.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There was a writel() being used on a 16-bit register.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
lockdep needs to have the waitqueue lock initialized for on-stack
waitqueues implicitly initialized by DECLARE_COMPLETION().
Annotate mmc_wait_for_req()'s on-stack completion accordingly.
Has no effect on non-lockdep kernels.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 3541/2: workaround for PXA27x erratum E7
[ARM] nommu: provide a way for correct control register value selection
[ARM] 3705/1: add supersection support to ioremap()
[ARM] 3707/1: iwmmxt: use the generic thread notifier infrastructure
[ARM] 3706/2: ep93xx: add cirrus logic edb9315a support
[ARM] 3704/1: format IOP Kconfig with tabs, create more consistency
[ARM] 3703/1: Add help description for ARCH_EP80219
[ARM] 3678/1: MMC: Make OMAP MMC work
[ARM] 3677/1: OMAP: Update H2 defconfig
[ARM] 3676/1: ARM: OMAP: Fix dmtimers and timer32k to compile on OMAP1
[ARM] Add section support to ioremap
[ARM] Fix sa11x0 SDRAM selection
[ARM] Set bit 4 on section mappings correctly depending on CPU
[ARM] 3666/1: TRIZEPS4 [1/5] core
ARM: OMAP: Multiplexing for 24xx GPMC wait pin monitoring
ARM: OMAP: Fix SRAM to use MT_MEMORY instead of MT_DEVICE
ARM: OMAP: Update dmtimers
ARM: OMAP: Make clock variables static
ARM: OMAP: Fix GPMC compilation when DEBUG is defined
ARM: OMAP: Mux updates for external DMA and GPIO
...
When there is remaining blocks untransferred, we get two error messages saying
almost the same thing. Make sure at most one is shown.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some controllers incorrectly report that the cannot do DMA. Forcefully enable
it for those that we know it works fine on.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some controllers fail to complete a reset unless you touch the clock register
first.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
New version number for sdhci driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As some specific controllers will have bugs, we need a way to map special
behaviour to certain hardware.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Properly test for controller interface to see if it's DMA capable. As many
controllers are misconfigured in this regard, also add debug parameters to
force DMA support either way.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The specification states that the capabilities register might need a reset to
get correct values after boot up.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check the interface version of the controller and bail out if it's an unknown
version.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Conform to the sdhci specification as to which inhibit bits should be checked
at different times.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The controller has an upper limit on the block size. Make sure we do not
cross it.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci controllers will issue an interrupt when a configurable number of
bytes have been transfered using DMA. The purpose is to handle multiple,
scattered memory pages.
Unfortunately, it requires that all transfers are completely aligned to
memory pages, which we cannot guarantee. So we just disable the function.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci controllers operate with blocks, not bytes. The PIO routines must
therefore make sure that the minimum unit transfered is a complete block.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The specification says that interrupts should be cleared before the source is
removed. We should also not set unknown bits.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci specification states that some registers must be written to in a
specific order.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the give timeout clock and calculate a proper timeout instead of using the
maximum at all times.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The reset register is automatically cleared when the reset has completed.
Hence, we should busy wait and not have a fixed delay.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current timeout loop assume that jiffies are updated. This might not be
the case depending on locks and if the kernel is compiled without preemption.
Change the system to use a counter and fixed delays.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci controllers can support up to three voltage levels. Detect which
and report back to the MMC layer.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As sdhci is a generic driver, it is helpful to see some more specific
identification of the actual hardware in dmesg. PCI vendor, device and
revision is sufficient in most cases.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A base clock value of 0 means that the driver must get the base clock through
some other means. As we have no other way of getting it, we must abort.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch makes OMAP MMC work again:
- Fix compile errors
- Do not ioremap base as it is already statically mapped
- Clean-up platform device handling
- Fix compile warnings
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- DMA CSR register is cleared by reading on omap1, but on
omap2 it is cleard by writing to it.
- DMA TOUT interrupt does not exist on omap24xx, rename it
- Add SECURE and MISALIGNED errors by default for omap24xx
- Add defines for external DMA request lines
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch from Andrew Victor
This patch includes code cleanups and minor fixes to the AT91RM9200 MMC
driver.
1. Replace calls to DBG() with pr_debug().
2. 'host' can never be null, so don't bother checking for that case.
3. Remove SA_SAMPLE_RANDOM from request_irq(). [Patch from Matt
Mackall]
4. clk_get() doesn't return NULL on error - need to test returned value
with IS_ERR().
5. Free resources if clk_get() or request_irq() fails.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MMC specification allows non-power of two block sizes. As such,
we should not pass the log2 block size to host drivers, but instead
pass the byte size.
However, ARM MMCI can only work with log2 block size, so continue to
pass both the log2 block size and byte block size. This means that
for the moment, the byte block size must remain a power of two, but
this is the first stage of removing this restriction for other hosts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On 64-bit machines, we just lost the uppermost 32 bits.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The driver is selectable on other than Au1200 Alchemy systems but won't
build nor work - there is no MMC hw.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
md->disk was being used in a debug message before it was allocated.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Pavel Pisa
There has been problems that for some paths that clock are not stopped
during new command programming and initiation. Result is issuing
of incorrect command to the card. Some other problems are cleaned too.
Noisy report of known ERRATUM #4 has been suppressed.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having every driver duplicate the set_ios debugging,
provide a single version in mmc.c which can be expanded as we
add additional functionality.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mmc_request_done should be called at the end of handling a request, not
between the data and initial command parts of the request.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no reason for the PXAMCI debug code to print so many lines - it
causes the kernel buffer to overflow when trying to debug this driver.
Remove some debug messages which are duplicated by core code, and
combine other messages, resulting in fewer characters written to the
kernel log.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Always send a stop command at the end of a data transfer. If we avoid
sending the stop command, some cards remain in data transfer mode, and
refuse to accept further read/write commands.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CSD contains a "read2write factor" which determines the multiplier to
be applied to the read timeout to obtain the write timeout. We were
ignoring this parameter, resulting in the possibility for writes being
timed out too early.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Pisa
The clock starting imxmci_start_clock() function contains hardware
issue workaround, which repeats start attempt, if SDHC does not react on
the first trial. But the second start attempt can be taken even, if the
first succeed and test code misses time limited clock running phase
due to delay caused by schedule to other task or some another device
interrupt. This change enables to detect such situation.
The performance is not issue, because usually at full clock rate
only about six loops in delay cycle are needed.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MMC layer gives us two parts for the timeout calculation - a fixed
timeout in nanoseconds, and a card clock-speed dependent part.
The PXA MMC hardware allows for a timeout based on the fixed host clock
speed only. This resulted in some cards being given a short timeout,
and therefore failing to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Pisa
This patch adds support of i.MX/MX1 SD/MMC controller.
It has been significantly redesigned from the original Sascha Hauer's
version to support scatter-gather DMA, to conform to latest Pierre Ossman's
and Russell King's MMC-SD Linux 2.6.x infrastructure.
The handling of all events has been moved to the softirq context
and is designed with no busy-looping in mind. Unfortunately
some controller bugs has to be overcome by limited looping
about 2-20 usec but these are observed only for initial card
recognition phase.
There are still some missing/missed IRQs problems under heavy load.
Help of somebody with access to the full SDHC design information
is probably necessary.
Regenerated against 2.6.16-git-060402 to solve clash with other patches.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds support for the MMC/SD card interface on the Atmel
AT91RM9200 processor.
Original driver was by Nick Randell, but a number of people have
subsequently worked on it. It's currently maintained by Malcolm Noyes.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than each driver test MMC_DEBUG itself, and define DEBUG,
pass it in via the makefile instead.
Fix drivers to use pr_debug() where appropriate, and avoid defining
a DEBUG() macro.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds OMAP MMC driver.
Signed-off-by: Juha Yrjl <juha.yrjola@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Carlos Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MODULE_PARM was actually breaking: recent gcc version optimize them out as
unused. It's time to replace the last users, which are generally in the
most unloved drivers anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Driver for the Secure Digital Host Controller Interface specification.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
platform_get_irq*() now returns on -ENXIO when the resource cannot be
found. Ensure all users of platform_get_irq*() handle this error
appropriately.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a trivial compilation warning:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_dma_callback’:
drivers/mmc/au1xmmc.c:743: warning: unused variable ‘status’
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/mmc/au1xmmc.c doesn't compile because commit
e92251762d introduced a typo and passes
the wrong argument to the mmc_resp_type macro.
Error because of the typo:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_send_command’:
drivers/mmc/au1xmmc.c:197: warning: implicit declaration of function ‘mmc_rsp_type’
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `au1xmmc_request':au1xmmc.c:(.text+0x89504): undefined reference to `mmc_rsp_type'
:au1xmmc.c:(.text+0x8968c): undefined reference to `mmc_rsp_type'
make: *** [.tmp_vmlinux1] Error 1
Error because of the wrong argument:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_send_command’:
drivers/mmc/au1xmmc.c:197: error: invalid type argument of ‘->’
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/mmc/au1xmmc.c currently doesn't compile; it needs to be
converted to use platform_driver. I cannot test this change because
of lack of hardware but I followed the drivers this one is based on,
and the code is certainly not worse than before.
drivers/mmc/au1xmmc.c: At top level:
drivers/mmc/au1xmmc.c:1002: error: ‘platform_bus_type’ undeclared here (not in a function)
make[2]: *** [drivers/mmc/au1xmmc.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a data transfer is small (less than a FIFO size) we would
hang waiting for the data to be read due to the PIO interrupt
not occuring. We allowed for this in our PIO interrupt handler,
but not when setting up a data transfer.
Apply the "fix" when setting up a data transfer as well.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/mmc/mmc_block.c: In function `mmc_blk_probe':
drivers/mmc/mmc_block.c:467: warning: long unsigned int format, different type arg (arg 5)
We don't know what size sector_t is - cast it.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some hosts need to know that a transfer will be multi-block.
Add a data flag to indicate multiple data block transfers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
HDIO_GETGEO is implemented in most block drivers, and all of them have to
duplicate the code to copy the structure to userspace, as well as getting
the start sector. This patch moves that to common code [1] and adds a
->getgeo method to fill out the raw kernel hd_geometry structure. For many
drivers this means ->ioctl can go away now.
[1] the s390 block drivers are odd in this respect. xpram sets ->start
to 4 always which seems more than odd, and the dasd driver shifts
the start offset around, probably because of it's non-standard
sector size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@suse.de>
Cc: <mike.miller@hp.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the coding style in the wbsd driver once and for all.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Version 4 of the MMC specification increased the version number of the
CID structure. None of the fields changed though so the only required
change is adding '4' to the approved list.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the wbsd driver to use the new suspend/resume functions added to
the PnP layer.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
add @uptodate argument to end_that_request_last() and @error
to rq_end_io_fn(). there's no generic way to pass error code
to request completion function, making generic error handling
of non-fs request difficult (rq->errors is driver-specific and
each driver uses it differently). this patch adds @uptodate
to end_that_request_last() and @error to rq_end_io_fn().
for fs requests, this doesn't really matter, so just using the
same uptodate argument used in the last call to
end_that_request_first() should suffice. imho, this can also
help the generic command-carrying request jens is working on.
Signed-off-by: tejun heo <htejun@gmail.com>
Signed-Off-By: Jens Axboe <axboe@suse.de>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since MMCI currently uses PIO to read data, we have to take steps
to ensure data cache coherency on aliasing CPU caches. Add the
necessary flush_dcache_page() calls.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
platform_device_register_simple() is going away, switch to
using platfrom_device_alloc() + platform_device_add(). Also
make sure that wbsd_driver gets unregistered when wbsd_init
fails.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Select a block size for IO based on the read and write block size
combinations, and whether the card supports partial block reads
and/or partial block writes.
If we are able to satisfy block reads but not block writes, mark
the device read only.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We were passing set_capacity() the capacity we calculated in terms of
the number of blocks on the card, which happened to be the right units
for 512-byte block cards. However, with 1024-byte block cards, we
end up setting the capacity to half the number of blocks. Fix this
by shifting by the appropriate amount.
Thanks to Todd Blumer for pointing this out.
Use get_capacity() to report the card capacity, rather than
recalculating it from the CSD information.
Finally, use our chosen IO block size for the SET_BLOCKLEN command
rather than the CSD read block size. Currently these are equivalent,
but will not be in the future.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems that people get confused about what is happening in
mmc_power_up(). Add a comment to make it clear why we have
a two stage process.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The routine reading the SCR wasn't paying proper attention to the
error codes returned from the driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A review against MMC/SD specifications found some errors in the current
implementation.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
wbsd_*_remove() is declared as __devexit but __devexit_p isn't used
when taking their addresses.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Uli Luckas
This is a simplification of patch 3116/1 as sugested by Russell King.
Signed-off-by: Uli Luckas <u.luckas@road-gmbh.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is the remaining misc drivers/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in misc files in
drivers/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Len Brown <len.brown@intel.com>
Acked-by: "Antonino A. Daplas" <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The printks that aren't for debugging should use the name of the controller,
not the driver name. Multiple MMC controllers aren't that common today, but
this is the right way to do things.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a broken if clause in the wbsd driver that can cause the
driver to try and configure the chip even though none is found. This
results in i/o on invalid ports.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a card doesn't support the "write block" command class then
any attempts to open the device should reflect this by denying
write access.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Proper handling of suspend/resume in the wbsd driver.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wbsd driver's card detection routing is a bit of a mess. This
patch cleans up the routine and makes it a bit more comprihensible.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove timer that was left from earlier cleanup.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean out trailing whitespace caused by not-so-great editor since it
generates a lot of problems with editors configured to automatically
strip whitespace.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert wbsd to use the new delay functionality in mmc_detect_change()
rather than implementing its own timer.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow PXA platforms to pass an appropriate delay value to the
PXA MCI driver for delaying detection changes.
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change mmc_detect_change() to take a delay argument such that
the detection of card insertions and removals can be delayed
according to the requirements of the host driver or platform.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only show the scr file in sysfs for SD cards. Previously this was present
for all cards but had a contents of 0 for MMC cards.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for Secure Digital specific features in the wbsd driver. Adds
support for read-only switch and wide bus transfers.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a write protection switch handling code to the PXA MMC driver so
that platform specific code can provide it if available.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Credit where credit is due.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Infrastructure for 4-bit bus transfers with SD cards.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Export the SCR register through sysfs.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Read the SD specific SCR register from the card.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the read-only switch on SD cards which must be enforced by the
host.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the Secure Digital protocol in the MMC layer.
A summary of the legal issues surrounding SD cards, as understood by yours
truly:
Members of the Secure Digital Association, hereafter SDA, are required to sign
a NDA[1] before given access to any specifications. It has been speculated
that including an SD implementation would forbid these members to redistribute
Linux. This is the basic problem with SD support so it is unclear if it even
is a problem since it has no effect on those of us that aren't members.
The SDA doesn't seem to enforce these rules though since the patches included
here are based on documentation made public by some of the members. The most
complete specs[2] are actually released by Sandisk, one of the founding
companies of the SDA.
Because of this the NDA is considered a non-issue by most involved in the
discussions concerning these patches. It might be that the SDA is only
interested in protecting the so called "secure" bits of SD, which so far
hasn't been found in any public spec. (The card is split into two sections,
one "normal" and one "secure" which has an access scheme similar to TPM:s).
(As a side note, Microsoft is working to make things easier for us since they
want to be able to include the source code for a SD driver in one of their
development kits. HP is making sure that the new NDA will allow a Linux
implementation. So far only the SDIO specs have been opened up[3]. More will
hopefully follow.)
[1] http://www.sdcard.org/membership/images/ippolicy.pdf
[2] http://www.sandisk.com/pdf/oem/ProdManualSDCardv1.9.pdf
[3] http://www.sdcard.org/sdio/Simplified%20SDIO%20Card%20Specification.pdf
This patch contains the central parts of the SD support. If no MMC cards are
found on a bus then the MMC layer proceeds looking for SD cards. Helper
functions are extended to handle the special needs of SD cards.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds a new ios for setting the chip select pin on MMC cards. Needed on
SD controllers which use this pin for other things and therefore cannot
have it pulled high at all times.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no point in having the host name duplicated between
the mmc_host structure and the encapsulated class device
structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create a mmc_host class to allow enumeration of MMC host controllers
even though they have no card(s) inserted.
Patch based on work by Pierre Ossman.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Even though the changes are minor for the next release an increasing
version number simplifies my support issues.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following possible cleanups:
- make some needlessly global code static
- remove the unneeded global function DBG_REG
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Wait 0.5 seconds before scanning for cards after an insertion interrupt.
The electrical connection needs this time to stabilise for some cards.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Defines for the different command classes as defined in the MMC and SD
specifications.
Removes the check for high command classes and instead checks that the
command classes needed are present.
Previous solution killed forward compatibility at no apparent gain.
Signed-of-by: Pierre Ossman
Updates to the wbsd driver.
* Fix to handle DAT3 card detection.
* Fixed bug which could cause large writes to stall in FIFO mode.
* Plug 'n Play support. In most cases you need ACPI PNP for this to work.
* Uses generic DMA API (ISA dependency removed).
Drivers that expect ISA DMA API are marked as such in Kconfig.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes u32 vs. pm_message_t in drivers/mmc, drivers/mtd and
drivers/scsi.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Pierre Ossman