The legacy old IDE ioctl API for this is a bit primitive so we try
and map stuff sensibly onto it.
- Set PIO over DMA devices to report 32bit
- Add ability to change the PIO32 settings if the controller permits it
- Add that functionality into the sff drivers
- Add that functionality into the VLB legacy driver
- Turn on the 32bit PIO on the ninja32 and add support there
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use ATA_ID_CFA_* constants for CFA specific identify data words 162 and 163.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When pata_legacy can't detect any device, it unregisters the
platform_device and fails detection. However, it forgets to detach
ata host triggering weird failures as the host later gets freed by
devres while still attached. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The libata driver has copied the code from the IDE driver which caused a post
2.4.18 regression on many HPT370[A] chips -- DMA stopped to work completely,
only causing timeouts. Now remove hpt370_bmdma_start() for good...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
WDC WD1600JS-62MHB5 successfully hits the window between ATA/ATAPI-7
and Serial ATA II standards and reports 3c/c3 signature which now is
assigned to SEMB. Make ata_dev_classify() report ATA_DEV_SEMB on the
sig and let ata_dev_read_id() work around it by trying IDENTIFY once.
This fixes bko#11579.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: David Haun <drhaun88@gmail.com>
Reported-by: Lars Wirzenius <liw@liw.fi>
Reported-by: Juan Manuel <jmcarranza@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Also remove the now-useless debug printouts which are supposed to
tell us when the scan starts and ends.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Along with MCP65, MCP67 and 73 also don't set CAP_NCQ. Force it.
Reported by zaceni@yandex.ru on bko#13014 and confirmed by Peer Chen.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: NightFox <zaceni2@yandex.ru>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename a slew of register name constants in sata_mv,
removing the _OFS suffix from them, and shortening some
of them in other ways as well.
Also, bump up the version number to reflect all recent changes.
In theory, no actual changes to the generated code,
other than the version number bump.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add remainder of workaround for errata SATA#13.
This prevents writes of certain adjacent 32-bit registers
from being combined into single 64-bit writes, which might
fail for the affected registers.
Most of sata_mv is already safe from this issue,
but adding this code to mv_write_cached_reg() will
catch the remaining cases and hopefully prevent future ones.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add _OFS suffix to more of the register offset names,
for consistency with the rest of the driver.
Also tag the defines for LTMODE and PHY_MODE4 to note
that read-after-write is necessary when updating those regs.
No code changes here.
[NOTE: this commit is undone a few commits later]
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Workaround for errata SATA#26.
Prevents accidently putting a drive to sleep when attempting COMRESET,
by ORing 0xf000 with the values written to SCR_CONTROL.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Workaround for 60x1-B2 errata PCI#7.
Write-combining may be unreliable when chip operates in PCI-X mode,
so disable write-combining when in PCI-X mode.
Also, update the errata comments at the top of sata_mv,
and include a note about errata PCI#11.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cosmetic change: replace .pio_mask=0x1f with .pio_mask=ATA_PIO4 everywhere.
Originally from Erik Inge Bolsø, now reworked for latest sata_mv.
Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Prevent racing on the main interrupt mask during port_start and port_stop.
Otherwise, we end up with IRQs masked on inactive ports,
and hotplug insertions then get missed later on.
Found while debugging (out of tree) target mode operations,
but the bug is present and impacting mainline as well.
This patch should also be considered for -stable.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Revert most of commit 6be96ac1d5e4d913e1f48299db083ada5321803b2,
originally from Lennert Buijtenheck (Marvell) and Saeed Bishara (Marvell),
since that commit causes sata_mv to oops at startup on SOC "Kirkwood".
The SOC variants do not have the hpriv->irq_{cause,mask}_ofs registers,
so don't try to write to them!
This patch should also be considered for -stable.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During driver initialization ahci_start_port may not be able
to turn LEDs off because the hardware may still be transmitting
a message. And since the BIOS may not be setting the LEDs to
off the drive LEDs may end up in a fault state. This has
been seen on ICH9r and ICH10r when configured in AHCI mode
instead of RAID mode, this patch doesn't key off a specific
set of device IDs but will give the EM transmit bit a chance
to clear if busy.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sony VGN-BX297XP fails suspend if the controller is powered down when
calling into ACPI suspend. Add the machine to piix_broken_suspend
list.
This problem was reported by GNUtoo@no-log.org on bko#10293.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: GNUtoo@no-log.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On a timeout call a device specific handler early in the recovery so that
we can complete and process successful commands which timed out due to IRQ
loss or the like rather more elegantly.
[Revised to exclude the timeout handling on a few devices that inherit from
SFF but are not SFF enough to use the default timeout handler]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If the device is signalling that there is data to drain after an error we
should read the bytes out and throw them away. Without this some devices
and controllers get wedged and don't recover.
Based on earlier work by Mark Lord
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ahci_transmit_led_message saves off the led_state
with a value that includes the port number OR'd
in, this incorrect value maybe reported back
in ahci_led_store.
For instance, if you turn off all the leds for
port 1 and cat the value back it will report 1
instead of 0.
# echo 0 > /sys/class/scsi_host/host1/em_message
# cat /sys/class/scsi_host/host1/em_message
1
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make libata more robust when parsing the multi_count
field from a drive's identify data. This prevents us from
attempting to use dubious multi_count values ad infinitum.
Reset dev->multi_count to zero and reprobe it each time
through this routine, as it can change on device reset.
Also ensure that the reported "maximum" value is valid
and is a power of two, and that the reported "count" value
is valid and also a power of two. And that the "count"
value is not greater than the "maximum" value.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For Marvell SoC chips, the HDD LED does not blink when there is
disk I/O if NCQ is enabled. Add a quirk that enables blink mode for
the LED while NCQ is enabled on any port of a SoC host controller.
Normal LED function is restored when NCQ is not enabled on any port.
The code to enable the blink mode is based on earlier code
and suggestions from Frans Pop, Saeed Bishara, and possibly others.
Signed-off-by: Mark Lord <mlord@pobox.com>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable use of the "all ports" IRQ coalescing optimization
for GEN_II / GEN_IIE chips that have dual host-controllers (8-ports).
Currently only the 6081 chip qualifies, but other chips may come along someday.
Rather than each half of the chip having to satisfy a local set of coalescing thresholds,
use of this feature groups all ports together under a single set of thresholds.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add IRQ coalescing to sata_mv (off by default).
This feature can reduce total interrupt overhead for RAID setups
in some situations, by deferring the interrupt signal until one or both of:
a) a specified io_count (completed SATA commands) is achieved, or
b) a specified time interval elapses after an IO completion.
For now, module parameters are used to set the irq_coalescing_io_count
and irq_coalescing_usecs (timeout) globally. These may eventually
be supplemented with sysfs attributes, so that thresholds can be set
on-the-fly and on a per-chip (or even per-host_controller) basis.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Various cosmetic changes in preparation for the IRQ coalescing feature.
Note that the various MV_IRQ_COAL_* definitions are restored/renamed
in the folloup patch which adds IRQ coalescing to the driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
platform_get_irq() can return -ENXIO, but since 'irq' is an
unsigned int, it does not show when the IRQ resource wasn't found.
Make irq an int so that we can use a single variable to test the
platform_get_irq() return value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
According to Alan:
>and yes the EFAR does UDMA66.
mwdma:
>Yep - wrong comment. The EFAR is a sort of clone of the PIIX and I
>copied the comment while EFAR don't appear to have copied the
>limitation
Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As noted by Alan:
>Your suspicions are correct here btw - the device can only do MWDMA1 and
>MWDMA2 (much like some PIIX devices)
Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Blacklist HP Compaq 6720s so that it doesn't play a "spin down,
spin up, spin down" ping-pong with the hard disk during system
power off.
Signed-off-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is initially needed to work around NCQ errata,
whereby the READ_LOG_EXT command sometimes fails
when issued in the traditional (sff) fashion.
Portions of this code will likely be reused for
implementation of the target mode feature later on.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is necessary for use with the upcoming "mv_qc_issue_fis()" patch,
but is being added separately here for easier code review.
When using command issue via the "mv_qc_issue_fis()" mechanism,
the initial ATA_BUSY bit does not show in the ATA status (shadow) register.
This can confuse libata! So here we add a hook to fake ATA_BUSY
for that situation, until the first time a BUSY, DRQ, or ERR bit is seen.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
so that it doesn't miss any protocols. Handle future cases where a
qc is specially marked for polled issue or where a particular chip
version prefers interrupts over polling for PIO.
This mimics the polling decision logic from ata_sff_qc_issue().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This also gets rid of any need for mv_mode_filter().
Using basic DMA on GEN_IIE requires setting an undocumented
bit in an undocumented register. For safety, we clear that
bit again when switching back to EDMA mode.
To avoid a performance penalty when switching modes,
we cache the register in port_priv, as already done for other regs.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Maintain a local (mv_port_priv) cache of frequently accessed registers,
to avoid having to re-read them (very slow) on every transistion
between EDMA and non-EDMA modes. This speeds up things like
flushing the drive write cache, and anything using basic DMA transfers.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no need to turn off intx explicitly on msi enable. This is
automatically handled by pci. Drop it.
This might be needed on machines if the BIOS turns intx off during
boot. However, there's no evidence of such behavior for ahci and
the only such case seems to be ICH5 PATA according to ata_piix.
Also, given the way ahci operates, it's highly unlikely BIOS ever
disables IRQ for the controller. However, as this change has slight
possibility of introducing failure, please schedule it for #upstream.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I'm not quite sure what freezing and thawing is used for. Tests showed
that the port is being frozen at initialisation state and thawed right
afterwards, then the functions were not called anymore. Dropping the
complete custom code for handling the frozen state seems to work at
least for a standard use case including mounting a partition, copying
some files in it (in parallel) and finally removing them and unmounting
the partition.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The biggest difference between rb532_pata_data_xfer() and
ata_sff_data_xfer32() is the call to ata_sff_pause() at the end of
rb532_pata_data_xfer() which I suppose to be unnecessary since it works
without. I've also tested using ata_sff_data_xfer() as replacement, but
since we know that the driver supports 32bit IO, using the optimised
version should be safe.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The only difference between rb532_pata_exec_command() and
ata_sff_exec_command() is added debugging output, so it can be dropped
and the standard op used instead.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since the delay used internally is just the same as ata_sff_pause()
uses, rb532_pata_finish_io() does exactly the same as ata_sff_pause()
and thus can be replaced by the later one.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove redundant code left over from the earlier patch 04/07.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Try and avoid unnecessary reconfiguration of the EDMA config register
on every single non-EDMA I/O operation, by moving the call to
mv_edma_cfg() into mv_stop_edma(). It must then also be invoked
from mv_hardreset() and from mv_port_start().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ATAPI support to sata_mv, using sff DMA for GEN_II chipsets,
and plain old PIO for GEN_IIE.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix mv_fill_sg() to zero out the reserved word (required for ATAPI),
and to include a memory barrier. This may also help with problems
reported by Jens on the PPC platform.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update the logic in ata_qc_from_tag() to match that used
in similar places elsewhere in libata.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange logic in mv_qc_issue() to handle protocols
other than ATA_PROT_DMA, ATA_PROT_NCQ, and ATA_PROT_PIO.
This is in preparation for later enabling ATAPI support.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange mv_start_dma() and friends, in preparation for adding
non-EDMA DMA modes, and non-EDMA interrupts, to the driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clean up the chipset GENeration FLAGS, and rename them
for consistency with other uses of GEN_XX within sata_mv.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Samsung DB-P70 somehow botched the first ICH9 SATA port. The board
doesn't expose the first port but somehow SStatus reports link online
while failing SRST protocol leading to repeated probe failures and
thus long boot delay.
Because the BIOS doesn't carry any identifying DMI information, the
port can't be blacklisted safely. Fortunately, the controller does
have subsystem vendor and ID set. It's unclear whether the subsystem
IDs are used only for the board but it can be safely worked around by
disabling SIDPR access and just using SRST works around the problem.
Even when the workaround is triggered on an unaffected board the only
side effect will be missing SCR access.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Joseph Jang <josephjang@gmail.com>
Reported-by: Jonghyon Sohn <mrsohn@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata keeps a shadow copy of the ATA CTL register (which is write only),
and only writes to the hardware when the required value doesn't match
the shadow. However this copy wasn't being maintained when performing
reset functions. This could cause problems for the first operation after
a reset when the correct value might not be written to the CTL register.
This problem was observed when hotplugging a drive: the identify command
was being issued with interrupts enabled, when they should have been
disabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a (rare) race condition in mv_interrupt() when using MSI.
The value of hpriv->main_irq_mask_addr can change on on the fly,
and without this patch we could end up writing back a stale copy
to the hardware.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hanno Böck reported a problem where an old Conner CP30254 240MB hard drive
was reported as 1.1TB in capacity by libata:
http://lkml.org/lkml/2009/2/13/134
This was caused by libata trusting the drive's reported current capacity in
sectors in identify words 57 and 58 if the drive does not support LBA and the
current CHS translation values appear valid. Unfortunately it seems older
ATA specs were vague about what this field should contain and a number of drives
used values with wrong byte order or that were totally bogus. There's no
unique information that it conveys and so we can just calculate the number
of sectors from the reported current CHS values.
While we're at it, clean up this function to use named constants for the
identify word values.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When SCR access is available and the link is offline, softreset is
skipped as it only wastes time and some controllers don't respond very
well. However, the skip path forgot to thaw the port, which not only
blocks further event notification from the port but also causes
repeated EH invocations on the same event on drivers which rely on
->thaw() to clear events if the IRQ is shared with another device or
port.
This problem has always been there but is uncovered by recent sata_nv
nf2/3 change which dropped hardreset support while maintaining SCR
access. nf2/3 doesn't clear hotplug event mask from the interrupt
handler but relies on ->thaw() to clear them. When the hardreset was
there, the reset action was never skipped and the port was always
thawed but, with the hardreset gone, ->prereset() determines that
there's no need for softreset and both ->softreset() and ->thaw() are
skipped. This leads to stuck hotplug event in the IRQ status register
triggering hotplug event whenever IRQ is delieverd on the same IRQ.
As the controller shares the same IRQ for both ports, this happens on
every IO if one port is occpupied and the other isn't.
This patch fixes the problem by making sure that the port is thawed on
reset-skip path.
bko#11615 reports this problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Robert Hancock <hancockrwd@gmail.com>
Reported-by: Dan Andresan <danyer@gmail.com>
Reported-by: Arne Woerner <arne_woerner@yahoo.com>
Reported-by: Stefan Lippers-Hollmann <s.L-H@gmx.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update MODULE_PARM_DESC for ADMA to reflect the fact that the
option is disabled by default.
Signed-off-by: Brandon Ehle <azverkan@yahoo.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Added the Device IDs for MCP89 AHCI controller.
Removed the IDs of MCP7B because this chipset had been cancelled.
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sense_buffer is used as DMA target and shouldn't be allocated on
stack. Use ap->sector_buf instead. This problem is spotted by Chuck
Ebbert.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata passes the returned value of dma_map_sg() to
dma_unmap_sg(),which is the misuse of dma_unmap_sg().
DMA-mapping.txt says:
To unmap a scatterlist, just call:
pci_unmap_sg(pdev, sglist, nents, direction);
Again, make sure DMA activity has already finished.
PLEASE NOTE: The 'nents' argument to the pci_unmap_sg call must be
the _same_ one you passed into the pci_map_sg call,
it should _NOT_ be the 'count' value _returned_ from the
pci_map_sg call.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These devices are generally used with ATA anyway and it seems that some
ATAPI will need us to issue the right number of words. Therefore as we
can't switch mid burst on VLB devices we should only use 32bit I/O for
suitable block sizes.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With 32bit PIO we can use the posted write buffers, but only for 32bit I/O
cycles. This means we must disable the FIFO for ATAPI where a final 16bit
cycle may occur.
Rework the FIFO logic so that we disable the FIFO then selectively
re-enable it when we set the timings on AMD devices. Also fix a case
where we scribbled on PCI config 0x41 of Nvidia chips when we shouldn't.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For some reason, sata_mv doesn't clear interrupt status during init
when it's running on an SoC host adapter. If the bootloader has
touched the SATA controller before starting Linux, Linux can end up
enabling the SATA interrupt with events pending, which will cause the
interrupt to be marked as spurious and then be disabled, which then
breaks all further accesses to the controller.
This patch makes the SoC path clear interrupt status on init like in
the non-SoC case.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hibernation didn't work for me since I started to use IT8212 controller.
I did some debugging (booting with no_console_suspend init=/bin/sh).
Found that resume fails (2.6.28) with "serial number mismatch 'some
garbage' != 'some other garbage'" and "revalidation failed" messages.
That's because the controller firmware fills different serial number in
the IDENTIFY every boot.
The patch below fixes the resume simply clearing the serial number. The
proper fix would be probably to fill in the serial number of the RAID
volume instead. I assume that there must be something like that stored on
the drives but I don't know where.
Fix resume on pata_it821x RAID volume by clearing the serial number in
IDENTIFY data, which is otherwise different on each boot.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 871af1210f (libata: Add 32bit
PIO support) has caused all kinds of errors on the ATAPI devices, so
it has been empirically proven that one shouldn't try to read/write
an extra data word when a device is not expecting it already. "Don't
do it then"; however, still use a chance to do 32-bit read/write one
last time when there are exactly 3 trailing bytes.
Oh, and stop pointlessly swapping the bytes to and fro on big-endian
machines by using io*_rep() accessors which shouldn't byte-swap.
This patch should fix the kernel.org bug #12609.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The @fnac.net will be shut down within a couple of months, so fix my
email address.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
3Gbps is often much more prone to transmission failures. It's usually
okay to let EH handle speed down after transmission failures but some
WD My Book drives completely shutdown after certain transmission
failures and after it only power cycling can revive them. Combined
with the fact that external drives often end up with cable assembly
which is longer than usual and more likely to have intervening gender,
this makes these drives very likely to shutdown under certain
configurations virtually rendering them unusable.
This patch implements HOARKGE_1_5_GBPS and applies it to WD My Book
such that 1.5Gbps is forced once the device is identified.
Please take a look at the following bz for related reports.
http://bugzilla.kernel.org/show_bug.cgi?id=9913
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Let -EAGAIN from EH device handling routines trigger EH retry without
consuming its tries count. This will be used to implement link SPD
horkage which requires hardreset to adjust SPD without affecting other
EH decisions. As it bypasses the forward progress guarantee provided
by the tries count, the requester is responsible for ensuring forward
progress.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When link is flaky at high speed, it isn't uncommon for a device to
repeatedly fail probing sequence early after successfully negotiating
high link speed. This often leads to consecutive hotplug events
without successful probing.
This patch improves libata EH such that it remembers probing trials
and if there have been more than two unsuccessful trials in the past
60 seconds, slows down link speed to 1.5Gbps.
As link speed negotiation is the duty of the PHY layer proper, the
goal of this fallback mechanism is to provide the last resort when
everything else fails, which unfortunately happens not too
infrequently, so no fancy 6->3->1.5 speeding down or highest
successful transmission speed seen kind of logics (yet).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add @spd_limit to sata_down_spd_limit() so that the caller can specify
the SPD limit it wants. This parameter doesn't get in the way even
when it's too low. The closest possible limit is applied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dev->ering used to be cleared together with the rest of ata_device in
ata_dev_init() which is called whenever a probing event occurs.
dev->ering is about to be used to track probing failures so it needs
to remain persistent over multiple porbing events. This patch
achieves this by doing the following.
* Instead of CLEAR_OFFSET, define CLEAR_BEGIN and CLEAR_END and only
clear between BEGIN and END. ering is moved after END. The split
of persistent area is to allow hotter items remain at the head.
* ering is explicitly cleared on ata_dev_disable() and when device
attach succeeds. So, ering is persistent throug a device's life
time (unless explicitly cleared of course) and also through periods
inbetween disablement of an attached device and successful detection
of the next one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_down_spd_limit() should check whether the link is online before
using the SPD value to determine how to limit the link speed. Factor
out onlineness test and test it from sata_down_spd_limit().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_dev_disable() is about to be more tightly integrated into EH
logic. Move it to libata-eh.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The dev->pio_mode > XFER_PIO_0 test is there to avoid unnecessary
speed down warning messages but it accidentally disabled SATA link spd
down during configuration phase after reset where PIO mode is always
zero.
This patch fixes the problem by moving the test where it belongs.
This makes libata probing sequence behave better when the connection
is flaky at higher link speeds which isn't too uncommon for eSATA
devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
While playing with nvraid, I found out that rmmoding and insmoding
often trigger hardreset failure on the first port (the second one was
always okay). Seriously, how diverse can you get with hardreset
behaviors? Anyways, make ck804 use noclassify variant too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix libata kernel-doc warnings:
Warning(linux-next-20090120//drivers/ata/libata-core.c:4720): Excess function parameter 'dev' description in 'ata_qc_new'
Warning(linux-next-20090120//drivers/ata/libata-scsi.c:428): No description found for parameter 'ap'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The SSS flag, which directs the OS to spin up one disk at a time
to not have the PSU blow out, sometimes gets set even when not needed.
The effect of this is a longer-than-needed boot time.
This patch adds a module parameter that makes the driver ignore SSS
at least as far as the parallel scan during boot is concerned...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix chip type for the Highpoint RocketRAID 1740 and 1742 PCI cards.
These really do have Marvell 6042 chips on them, rather than the 5081 chip.
Confirmed by multiple (two) users (for the 1740), and by examining
the product photographs from Highpoint's web site.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I tried compiling 2.6.29-rc1 and 2.6.29-rc3 with libata debugging enabled
and got the following error:
CC [M] drivers/ata/sata_sil.o
drivers/ata/sata_sil.c: In function 'sil_fill_sg':
drivers/ata/sata_sil.c:327: error: 'pi' undeclared (first use in this function)
drivers/ata/sata_sil.c:327: error: (Each undeclared identifier is reported only once
drivers/ata/sata_sil.c:327: error: for each function it appears in.)
make[2]: *** [drivers/ata/sata_sil.o] Error 1
make[1]: *** [drivers/ata] Error 2
make: *** [drivers] Error 2
include/linux/libata.h has the following enabled:
#define ATA_DEBUG
#define ATA_VERBOSE_DEBUG
#define ATA_IRQ_TRAP
This fixes the compilation.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit e57db7b (SATA Sil: Blacklist system that spins off disks during ACPI power off)
breaks build like the following, in both cases when CONFIG_DMI set or not.
drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast
sata_sil.c should include dmi.h
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hibern_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
SATA PIIX: Blacklist system that spins off disks during ACPI power off
SATA Sil: Blacklist system that spins off disks during ACPI power off
SATA AHCI: Blacklist system that spins off disks during ACPI power off
SATA: Blacklisting of systems that spin off disks during ACPI power off
DMI: Introduce dmi_first_match to make the interface more flexible
Hibernation: Introduce system_entering_hibernation
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP 2510p that uses the ata_piix driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP nx6325 that uses the sata_sil driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP nx6310 that uses the AHCI driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce new libata flags ATA_FLAG_NO_POWEROFF_SPINDOWN and
ATA_FLAG_NO_HIBERNATE_SPINDOWN that, if set, will prevent disks from
being spun off during system power off and hibernation, respectively
(to handle the hibernation case we need the new system state
SYSTEM_HIBERNATE_ENTER that can be checked against by libata, in
analogy with SYSTEM_POWER_OFF).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver has been tested without the call to set_irq_type at this
point and occurs to work fine, so it should be safe to remove it.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It supports VX855 and future chips whose IDE controller uses PCI ID 0x0571.
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update Kconfig for sata_mv with full list of chips supported,
and (finally!) remove the "EXPERIMENTAL" designations.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable reliable use of Message-Signaled Interrupts (MSI) in sata_mv
by masking further chip interrupts within the main interrupt handler.
Based upon a suggestion by Grant Grundler.
MSI is working reliably in all of my test systems here now.
Signed-off-by: Mark Lord <mlord@pobox.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I noticed that during initialization sata_mv.c assumes that the main
interrupt mask has its default value of 0. The function
mv_platform_probe(..) initializes a shadow irq mask with 0 assuming
that's the value of the controller's register. Now
mv_set_main_irq_mask(..) only writes the controller's register if the
new value differs from the "shadowed" value. This is fatal when trying
to disable all interrupts in mv_init_host(..), i.e. the following
function call does not write anything to the main irq mask register:
mv_set_main_irq_mask(host, ~0, 0);
The effect I see on my machine (QNAP TS-109 II) with booting via kexec
(with Linux as a 2nd-stage boot loader) is that if the sata_mv module
was still loaded when performing kexec, then the new kernel's sata_mv
module starts up with interrupts enabled. This results in an unhandled
IRQ and breaks the boot process.
The unhandled interrupt itself might also be fixed by Lennert's patch
proposed at http://markmail.org/message/kwvzxstnlsa3s26w which I did not
try yet.
However I still propose to additionally initialize the shadow variable
with the current contents of the main irq mask register to get both in
sync and allow proper disabling the main irq mask. This fixes the
unhandled irq on my machine.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove unneeded nsect restriction from GenII NCQ path,
and improve comments to explain why this is not a problem.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove silly read-modify-write sequences when clearing interrupts
in hc_irq_cause. This gets rid of unneeded MMIO reads, resulting in
a slight performance boost when switching between EDMA and non-EDMA
modes (eg. for cache flushes).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a longstanding bug for the 8-port Marvell Sata controllers (508x/6081),
where accesses to the upper 4 ports would cause lost-interrupts / timeouts
for the lower 4-ports. With this patch, the 6081 boards should finally be
reliable enough for mainstream use with Linux.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MCP5x family of controllers seem to share much more with nf2's as far
as reset protocol is concerned. It requires heardreset to get the PHY
going and classfication code report after hardreset is unreliable.
Create a new board type MCP5x and use noclassify hardreset. SWNCQ is
modified to inherit from this new type.
This fixes hotplug regression reported in kernel bz#12351.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
nv_nf2_hardreset() will be used by other flavors too. Rename it to
nv_noclassify_hardreset().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Asus Pundit-R with atiixp controller has the second port missing and,
very unusually, its status is stuck at 0x7f and all others at 0. This
meanst that it fails TF access test but gets detected as a disk due to
classification code check and then evades polling IDENTIFY presence
detection thanks to the missing BSY in the status value causing
excessive delays during boot.
This patch makes libata-sff HSM set NODEV_HINT if the status is 0x7f
to make polling IDENTIFY presence detection work for these machines.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The EH message for NODEV_HINT path was describing the opposite
condition. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
while I was looking over kernel sources I've found this small bug.
Formerly, zero was returned even if an error happened.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/ata/pata_ali.c:44: error: static declaration of 'isa_bridge' follows non-static declaration
arch/alpha/include/asm/pci.h:274: error: previous declaration of 'isa_bridge' was here
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cavium OCTEON processor support was recently merged, so now we have
this CF driver for your consideration.
Most OCTEON variants have *no* DMA or interrupt support on the CF
interface so for these, only PIO is supported. Although if DMA is
available, we do take advantage of it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table. I add a
new column for dmack_hold time. The values were obtained from the
Compact Flash specification Rev 4.1.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Port enabledness test fits much better into init_one() instead of
pre_reset(). The reason why these tests are in pre_reset() is purely
historical at this point. Move it to init_one(). This will help
further changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
for SAS drivers.
Caught by Ke Wei (and team?) at Marvell.
Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The UDMA affliction is apparently specific to revision 0x11. Keeps us in sync
with drivers/ide current.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes a wrong WARN_ON that was triggered by 32bit PIO support:
WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x45e/0x750()
__atapi_pio_bytes simply doesnt know enough to decide if there is a bug.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In a discussio with Jeff Garzik, he mentioned that the serialization
for the libata port probes only needs to be within the domain of a host.
This means that for the first port of each host (with ID 0), we don't
need to wait, so we can relax our serialization a little.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a per host flag that allows drivers to opt in into
having its busses scanned in parallel.
Drivers that do not set this flag get their ports scanned in
the "original" sequence.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (94 commits)
ACPICA: hide private headers
ACPICA: create acpica/ directory
ACPI: fix build warning
ACPI : Use RSDT instead of XSDT by adding boot option of "acpi=rsdt"
ACPI: Avoid array address overflow when _CST MWAIT hint bits are set
fujitsu-laptop: Simplify SBLL/SBL2 backlight handling
fujitsu-laptop: Add BL power, LED control and radio state information
ACPICA: delete utcache.c
ACPICA: delete acdisasm.h
ACPICA: Update version to 20081204.
ACPICA: FADT: Update error msgs for consistency
ACPICA: FADT: set acpi_gbl_use_default_register_widths to TRUE by default
ACPICA: FADT parsing changes and fixes
ACPICA: Add ACPI_MUTEX_TYPE configuration option
ACPICA: Fixes for various ACPI data tables
ACPICA: Restructure includes into public/private
ACPI: remove private acpica headers from driver files
ACPI: reboot.c: use new acpi_reset interface
ACPICA: New: acpi_reset interface - write to reset register
ACPICA: Move all public H/W interfaces to new hwxface
...
Convert WARN_ON() on command issue/completion paths to WARN_ON_ONCE()
so that libata doesn't spam the machine even when one of those
conditions triggers repeatedly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This matters for some controllers and in one or two cases almost doubles
PIO performance. Add a bmdma32 operations set we can inherit and activate
it for some controllers
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There is an issue in ATI SB600/SB700 SATA that PxSERR.E should not be
set on some conditions, which will lead to many SATA ODD error messages.
commit 55a61604cd is the workaround.
Since SB800 fixed this HW issue, IGN_SERR_INTERNAL should be withdrawn
for SB800.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reimplement mode programming logic of pata_hpt366 such that it's
identical to that of IDE hpt366 driver. The differences were...
* pata_hpt366 used 0xCFFF8FFFF to mask pio modes and 0x3FFFFFFF dma
modes. IDE hpt366 uses 0xC1F8FFFF for PIO, 0x303800FF for MWDMA and
0x30070000 for UDMA.
* pata_hpt366 doesn't set 0x08000000 for PIO unless it's already set
and always turns it on for MWDMA/UDMA. IDE hpt366 doesn't bother
with the bit. It always uses what was there.
* IDE hpt366 always clears 0xC0000000. pata_hpt366 doesn't.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
According to the Compact Flash specification r4.1, PIO modes 5 and 6
do not use iordy.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
--
UPD include/linux/compile.h
`___pata_platform_remove' referenced in section `__ksymtab_gpl' of
drivers/built-in.o: defined in discarded section `.devexit.text' of
drivers/built-in.o
make: *** [.tmp_vmlinux1] Error 1
--
__pata_platform_remove() should not be in discarded section
__pata_platform_remove(struct device *dev) is invoked in both
pata_platform.c and pata_of_platform.c by reomve function defined in
discarded section ".devexit.text". An exported function should not be put
into discarded section.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
AFAICT, struct sil24_port_multiplier isn't used anywhere. Remove it.
Signed-off-by: Grant Grundler <grundler@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The present AHCI driver seems to support SATA GEN 3 speed, but the related
messages should be modified.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Certain ACPI implementations mess up IOCFG on _STM making libata
detect cable type incorrectly after a suspend/resume cycle. This
patch makes ata_piix save IOCFG on attach, use the saved value for
things which aren't dynamic and restore it on detach so that the next
driver also gets the BIOS initialized value.
This patch contains the following changes.
* makes ich_pata_cable_detect() use saved_iocfg.
* make piix_iocfg_bit18_quirk() take @host and use saved_iocfg.
* hpriv allocation moved upwards to save iocfg before doing anything
else.
This fixes bz#11879. Andreas Mohr reported and diagnosed the problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In very obscure cases this can cause problems. We need to help the hardware
out a bit to avoid DMA problems on a reset.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Correct the DMA bit flags (UDMA and MWDMA were swapped)
Add workarounds so that we clear ERR and INTR bits before issuing a DMA
Add workarounds so that we stop a live DMA before touching the CTL register
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As suggested by Linus: Don't do the libata init in 2 separate
steps with a global sync inbetween, but do it as one async step,
with a local sync before registering the device.
This cuts the boottime on my machine with 2 sata controllers down
significantly, and it seems to work. Would be nice if the libata
folks take a good look at this patch though..
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
This patch makes the libata port scanning asynchronous (per device).
There is a synchronization point before doing the actual disk scan
so that device ordering is not affected.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
External driver files should not include any private acpica headers.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
scsi_execute() and scsi_execute_req() discard the residual length
information. Some callers need it. This adds residual argument
(optional) to scsi_execute and scsi_execute_req.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This implements support for the Large Block Transfer feature found in Silicon
Image 311x controllers. This allows transferring bigger contiguous chunks of
data from system memory and avoids the 64KB boundary restriction of standard
SFF controllers.
This is based on a patch from Jeff Garzik (from the sii-lbt branch of
libata-dev) but includes a few bug fixes: Since the bmdma2 register does not
implement the status bits, the original bmdma register must be used except
where the bmdma2 register is required. As well the DMA boundary should be
31-bit instead of 32-bit since the top bit of the length field is still
required for the PRD end-of-table flag.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit
ATA: piix, fix pointer deref on suspend
fixed a possible oops in an ugly manner. Use newly introduced dmi_match()
to make the code pretty again.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The patchlet below blacklists NCQ on OCZ CORE v2 SSD drive(s). Even
though the drive advertises NCQ support with queue depth 1, it responds
with all-zeroes FIS to NCQ commands which triggers ata error handling
several times before the kernel decides to disable NCQ on the drive.
Signed-off-by: Lubomir Bulej <lubomir.bulej@dsrg.mff.cuni.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_port_detach() first made sure EH saw ATA_PFLAG_UNLOADING and then
assumed EH context belongs to it and performed detach operation
itself. However, UNLOADING doesn't disable all of EH and this could
lead to problems including triggering WARN_ON()'s in EH path.
This patch makes port detach behave more like other EH actions such
that ata_port_detach() requests EH to detach and waits for completion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When restoring SControl during detach, PMP links should be handled
first as changing SControl of the host link can affect SCR access of
PMP links.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There currently are the following looping constructs.
* __ata_port_for_each_link() for all available links
* ata_port_for_each_link() for edge links
* ata_link_for_each_dev() for all devices
* ata_link_for_each_dev_reverse() for all devices in reverse order
Now there's a need for looping construct which is similar to
__ata_port_for_each_link() but iterates over PMP links before the host
link. Instead of adding another one with long name, do the following
cleanup.
* Implement and export ata_link_next() and ata_dev_next() which take
@mode parameter and can be used to build custom loop.
* Implement ata_for_each_link() and ata_for_each_dev() which take
looping mode explicitly.
The following iteration modes are implemented.
* ATA_LITER_EDGE : loop over edge links
* ATA_LITER_HOST_FIRST : loop over all links, host link first
* ATA_LITER_PMP_FIRST : loop over all links, PMP links first
* ATA_DITER_ENABLED : loop over enabled devices
* ATA_DITER_ENABLED_REVERSE : loop over enabled devices in reverse order
* ATA_DITER_ALL : loop over all devices
* ATA_DITER_ALL_REVERSE : loop over all devices in reverse order
This change removes exlicit device enabledness checks from many loops
and makes it clear which ones are iterated over in which direction.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds MDMA/UDMA support using BestComm for DMA on the MPC5200
platform. Based heavily on previous work by Freescale (Bernard Kuhn,
John Rigby) and Domen Puncer.
With this patch, a SanDisk Extreme IV CF card gets read speeds of
approximately 26.70 MB/sec.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Alan Cox