From: Steve Hodgson <shodgson@solarflare.com>
Currently we can set multicast hash immediately (in atomic context)
but must delay setting MAC promiscuity. There is not that much
point in deferring one but not the other, and setting the multicast
hash on Siena will involve a firmware request. So process them
both in efx_mac_work().
Also, set the broadcast bit in the multicast hash in
efx_set_multicast_list(), since this is required for both Falcon and
Siena.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Only the XMAC on Falcon needs help from the driver to poll and reset
the MAC-PHY link (XAUI); GMII is a simple parallel bus and on later
NICs firmware takes care of the XAUI link. Also, an XMAC interrupt
currently schedules a work item which simply clears a flag
(efx_nic::mac_up) to be checked by the regular monitor (or the next
link reconfiguration, if that is sooner).
Rename the flag to xmac_poll_required, changing its sense. Remove the
needless indirection and just set the flag immediately. Call
falcon_xmac_poll() directly where required.
Add a new generic operation mac_op::check_fault to check the link
outside of regular monitoring, as required during self-tests.
(Note that this leaves us with an unused work item, but we will
immediately have another use for it.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Currently we initiate MAC stats DMA and busy-wait for completion when
stats are requested. We can improve on this with a periodic timer to
initiate and poll for stats, and opportunistically poll when stats are
requested.
Since efx_nic::stats_disable_count and efx_stats_{disable,enable}()
are Falcon-specific, rename them and move them accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although efx_init_port() is only called at probe time and so cannot
race with port reconfiguration, most of the functions it calls can
expect to be called with the MAC lock held.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid overrunning the hardware limit of 4 concurrent RX queue flushes.
Expand the queue flush state to support this. Make similar changes to
TX flushing to keep the code symmetric.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put all static information in struct falcon_board_type and replace it
with a pointer in struct falcon_board. Simplify probing aocordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although all the defined fields in these registers are within 32 bits,
they are architecturally defined as 128-bit like most other Falcon
registers. In particular, we must use efx_reado() to ensure proper
locking when reading MD_STAT_REG.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These were accidentally undersized by a factor of 2, which limited
performance.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support all three modes of macvlan at
runtime, extend the existing netlink protocol
to allow choosing the mode per macvlan slave
interface.
This depends on a matching patch to iproute2
in order to become accessible in user land.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows each macvlan slave device to be in one
of three modes, depending on the use case:
MACVLAN_PRIVATE:
The device never communicates with any other device
on the same upper_dev. This even includes frames
coming back from a reflective relay, where supported
by the adjacent bridge.
MACVLAN_VEPA:
The new Virtual Ethernet Port Aggregator (VEPA) mode,
we assume that the adjacent bridge returns all frames
where both source and destination are local to the
macvlan port, i.e. the bridge is set up as a reflective
relay.
Broadcast frames coming in from the upper_dev get
flooded to all macvlan interfaces in VEPA mode.
We never deliver any frames locally.
MACVLAN_BRIDGE:
We provide the behavior of a simple bridge between
different macvlan interfaces on the same port. Frames
from one interface to another one get delivered directly
and are not sent out externally. Broadcast frames get
flooded to all other bridge ports and to the external
interface, but when they come back from a reflective
relay, we don't deliver them again.
Since we know all the MAC addresses, the macvlan bridge
mode does not require learning or STP like the bridge
module does.
Based on an earlier patch "macvlan: Reflect macvlan packets
meant for other macvlan devices" by Eric Biederman.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have very similar code for rx statistics in
two places in the macvlan driver, with a third
one being added in the next patch.
Consolidate them into one function to improve
overall readability of the driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The veth driver contains code to forward an skb
from the start_xmit function of one network
device into the receive path of another device.
Moving that code into a common location lets us
reuse the code for direct forwarding of data
between macvlan ports, and possibly in other
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The velocity hardware can handle up to 7 memory segments. This can be
turned on and off via ethtool. The support was removed in commit
83c98a8cd0
but is re-enabled and cleaned up here. It's off by default.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VIA driver has changed the default for the DMA_LENGTH_DEF parameter.
Together with adaptive interrupt supression and NAPI support, this
improves performance quite a bit
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds NAPI support for VIA velocity. The new velocity_poll
function also pairs tx/rx handling twice which improves perforamance on
some workloads (e.g., netperf UDP_STREAM) significantly (that part is
from the VIA driver).
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
(Partially from the upstream VIA driver). Tweaking the number of
frames-per-interrupt and timer-until-interrupt can reduce the amount of
CPU work quite a lot.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
(From the VIA driver). The current code does not guarantee 64-byte
alignment since it simply does
int add = skb->data & 63;
skb->data += add;
(via skb_reserve). So for example, if the skb->data address would be
0x10, this would result in 32-byte alignment (0x10 + 0x10).
Correct by adding
64 - (skb->data & 63)
instead.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As side effect, consume less stack.
-rtl8169_get_mac_version [vmlinux]: 432
-rtl8169_init_one [vmlinux]: 376
+rtl8169_init_one [vmlinux]: 136
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generated with the following semantic patch
@@
struct net *n1;
struct net *n2;
@@
- n1 == n2
+ net_eq(n1, n2)
@@
struct net *n1;
struct net *n2;
@@
- n1 != n2
+ !net_eq(n1, n2)
applied over {include,net,drivers/net}.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] drivers/net/wireless/ath/ath9k/recv.o
drivers/net/wireless/ath/ath9k/recv.c: In function `ath_rx_prepare':
drivers/net/wireless/ath/ath9k/recv.c:208: warning: comparison is always true due to limited range of data type
drivers/net/wireless/ath/ath9k/recv.c:220: warning: comparison is always false due to limited range of data type
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define name tables for these enumerations in a similar way as for
loopback. Move the loopback name table together with them.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All files that include ethtool.h, rx.h or tx.h are also including
efx.h, and there is no good reason to separate out the few
declarations they contain. Therefore fold them into efx.h.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At some point these casts were used to remove const qualification, but
they are now unneeded.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preparation for moving Falcon-specific state required by other
Falcon-specific code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename struct efx_board to struct falcon_board.
Introduce and use inline function to look up board info from struct
efx_nic, in preparation for moving it.
Move board init and fini calls into NIC probe and remove functions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_board::init_leds was introduced as a second stage of
initialisation because of the inter-dependency between the board and
PHY. We want to move board initialisation into NIC probing, which is
too early to use MDIO, so SFN4111T initialisation also needs to be
split.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only some PHYs have firmware support for a LED blink mode, so we
currently blink the others in a timer function. Since all PHYs have
simple on and off modes, we don't gain anything by using multiple
blink implementations. Also, since we have a process context there
is no need to use a timer.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the need to use a label and goto, and makes the two
branches mirror each other more closely.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function no longer has any common cleanup code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finish the job by removing the structure member.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gso_max_size must be set based on the value of the underlying device to
support devices not using the full 64k.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copied from original one-line patch here:
http://bugzilla.kernel.org/show_bug.cgi?id=14267#c26
(This is for 2.6.33 and beyond, where the bool was changed to a flag by
"cfg80211: convert bools into flags". -- JWL)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stall workaround doesn't work with bcm4320a devices like with bcm4320b.
This workaround actually causes more stalls/device freeze on bcm4320a.
Therefore disable stall workaround by default.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_query_oid overwrites *len which stores buffer size to return full size
of received command and then uses *len with memcpy to fill buffer with
command.
Ofcourse memcpy should be done before replacing buffer size.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current blinking rate is calculated based on the difference between
current tx/rx byte counts and priv->led_tpt.
priv->led_tpt should not get reset in iwl_leds_init(), this function can be
called by bring interface "up" or "down", or when uCode sysassert occurred.
resetting the led_tpt parameter will introduce incorrect led blinking behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change error message for command queue full
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To help iwlagn uCode debugging, event log will dump to syslog when driver
detect uCode error occurred, but this only happen when compile with
CONFIG_IWLWIFI_DEBUG and debug flag is enabled; which is not always
the case. Also, there is another problem, if the flag is set, the entire
event log buffer will be dump to syslog, it can flood the syslog and
make it very difficult to debug the problem.
Change the default to only dump last 20 entries of event log to syslog
unless the following condition meets:
1. both compile with CONFIG_IWLWIFI_DEBUG and debug flag
is enabled, and then dump the entire event buffer to syslog.
2. dump event log request from debugfs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we get a state change of associated or not, we need to tell the
ucode via the RX_ON command using the filter flags. This will prevent
the ucode from sending any packets when not associated, specifically not
sending NULL QOS packets after a deauthentication which causes the AP to
repeatedly send deauth's in some situations.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
uCode error log contain information as to what the error was and where
it occurred necessary to debug any uCode issues.
Always log the information without special debug flag, this can help to
capture the important information when error happened.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For "sram" debugfs file, if user did not specify the offset and length,
dump the entire data portion of sram by default.
Data portion is 0x800000 - 0x80ffff, but the actual data size is known
to the driver from the ucode file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the PCI_ID list for 5xx0 series.
Remove all the PCI_IDs which never made into production or not longer in
production.
Also make sure the supported bands(a/b/g/n) match specified PCI_IDs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since IO tracing is usually not needed and
generates a lot of data, separate it into
its own trace system so that we can always
enable iwlwifi:* and not have to worry about
getting too much data. If IO tracing is then
really needed we can enable iwlwifi_io:* in
addition and get that data.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
reserved2 field in "struct iwl4965_addsta_cmd" is __le16.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dynamically allocate memory for dumping SRAM based on the length of memory
to be displayed.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For tx_queue, need to increase the buffer size allocated for it,
so all the queues information can be displayed
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the correct Read/Write file permission for iwlwifi debugfs files
based on the functionality of the files
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED blink rate is based on the traffic load, when tx/rx traffic counts
got reset, we also need to reset the led_tpt to prevent incorrect
blink rate being calculated.
Merge both clear_tx_statistics() and clear_rx_statistics() into
single clear_traffic_statistics() function, when reset the traffic byte
counts, both tx and rx need to be reset at the same time, to make
sure calculated the correct led blink rate.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting "Spatial multiplexing Power Save" as part of
per device configuration parameter.
Report to uCode based on priv->conf setting, so driver can
have more control of how different devices should operate
in power save mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED blinking rate is based on tx/rx traffic, the most reasonable place
to do it is after update the traffic byte counts
This fixes the recent LED blinking breakage on 3945 introduced by "iwlwifi:
separate led function from statistic notification"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CSR_INT_COALESCING previously had only one, but now has two single-byte fields.
With only one single-byte field (lowest order byte) it was okay to write via
iwl_write32(), but now with two, an iwl_write32() to the lower order field
clobbers the other field (odd-address CSR_INT_PERIODIC_REG, offset 0x5), and an
iwl_write32() to CSR_INT_PERIODIC_REG could clobber the lowest byte of the
next-higher register (CSR_INT, offset 0x8).
Fortunately, no bad side effects have been produced by the iwl_write32()
usage, due to order of execution (low order byte was always written before
higher order byte), and the fact that writing "0" to the low byte of the
next higher register has no effect (only action is when writing "1"s).
Nonetheless, this cleans up the accesses so no bad side effects might occur
in the future, if execution order changes, or more bit fields get added to
CSR_INT_COALESCING.
Add some comments regarding periodic interrupt usage.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To support byte writes to CSR_INT_COALESCING and CSR_INT_PERIODIC registers,
add iwl_write8(), including debug/trace support.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sign of correction coefficients was lost in the calculations, which
caused high packetloss in 802.11a mode after the results were applied.
Fixed by removing unneccesary and broken AND with a bit mask.
Signed-off-by: Lukas Turek <8an@praha12.net>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This rewrites the error handling policies in the TX status handler.
It tries to be error-tolerant as in "try hard to not crash the machine".
It won't recover from errors (that are bugs in the firmware or driver),
because that's impossible. However, it will return a more or less useful
error message and bail out. It also tries hard to use rate-limited messages
to not flood the syslog in case of a failure.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has been tested with a 802.11 frame generator and by checking the FCS field
of each received frame with the value reported by the Atheros hardware. This
patch is useful if you are trying to analyze non standard 802.11 frame going
over the air.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipw2200 is able to detect when it's been hard-killed, but doesn't update
the core rfkill state or update userspace. Ensure that the state is updated,
allowing the rfkill core to notify userspace.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
libipw unconditionally calls wiphy_unregister, but it's up to the driver
to register it in the first place. ipw2100 fails to do so. Add the necessary
glue code, and also ensure that rfkill statuses get set up appropriately.
(Augmented for proper wiphy_unregister placement. -- JWL)
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initiate the conversion of libipw to the new cfg80211 configuration API.
For now, leave CONFIG_IPW2200_PROMISCUOUS stuff alone. Eventually
migrate it to cfg80211 when the add/del/change_virtual_intf methods
are implemented.
(v2: Fix unconditional wiphy_unregister in libipw which was causing
problems for ipw2100, somewhat based on prior attempted fix
by Zhu Yi <yi.zhu@intel.com>. Previously both original version of
this patch and Zhu Yi's fix attempt were reverted due to
discovery of regressions. -- JWL)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix soft-lockup in hso.c which is triggered on SMP machine when
modem is removed while file descriptor(s) under /dev are still open:
old version called kref_put() too early which resulted in destroying
hso_serial and hso_device objects which were still used later on.
Signed-off-by: Antti Kaijanmäki <antti.kaijanmaki@nomovok.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Antti Kaijanmäki <antti.kaijanmaki@nomovok.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There appears to be a stray setting of the VFE bit when registering vlans.
This should not be done as vlan filtering should be enabled any time the
interface is not in promiscous mode
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While configuring rscctl use rx buffer length from rx ring structure
instead of passing rx_buf_len to ixgbe_configure_rscctl
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Divide 82599 HWRSC counters into aggregated and flushed to count number of
packets getting coalesced per TCP connection.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can run out of mccq wrbs when completions don't arrive
due to an unresponsive card. This must not hit a BUG_ON(); instead
log a msg and return an error.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling msix was missing when probe fails after enabling msix.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These cmds are issued to the fw in probe/resume and remove/suspend
paths to help fw execute some initialization and cleanup code.
This change needed the be_hw_up() code to be refactored as be_get_config().
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To send upto 64 addresses in the multicast-set cmd, the non-embeeded cmd format
that provides for a bigger buffer is used instead of an embedded format.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the external timer cannot be used the driver
will continue to work without mitigation.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andreas Lohre reported that the driver crashes when trying
to register_netdev(), he sugessted to move dev->netdev_ops initialization
before calling register_netdev(), it worked for him.
Reported-by: Andreas Lohre <alohre@gmail.com>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Along with netdev->perm_addr, mac address will be
maintained in device private structure.
o Device limitation: We need to set mac address when ever
interface comes up.
In ALB/TAL mode, bonding driver calls set_mac for all slave with bond mac address.
But bonding driver set netdev->dev_addr field to its original value,
after enslaving interfaces.
When ever active slave changes, it swap dev_addr of inactive slave with active.
Yet it doesn't notify driver about change in netdev->dev_addr.
As netxen driver need to set mac addr when ever interface comes up,
it can't rely on netdev->dev_addr field. Specially in case of bonding mode ALB/TLB.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel crashes, if promisc mode set without disabling rx queue.
Before changing mode in NX2031 chip, wait till rx queue drains.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid resetting memory during initialization, skip this memory
block during driver probe.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx unit hang detection code in e1000e detects other hangs caused by
hardware components (e.g. Rx, DMA units), but it is not possible to detect
exactly which component is hung so it has always assumed a Tx unit hang.
When dumping a message to the system log because of a hang, this patch adds
more data to help narrow the cause of the issue and makes the message
non-Tx-specific. Because this new code reads PHY registers which can
sleep, move it off to a workqueue. This and all previously existing work
tasks in the driver are now cancelled when the driver is removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mutex_lock() calls might_sleep() the driver doesn't have to here.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A failure to initialize the identification LED is not a fatal condition and
should allow the init path to continue.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out a pm_qos DMA latency requirement set when the driver is
loaded when parts that support early receive of jumbo frames are probed
could have that requirement overidden if another part supported by the
driver (one that does not support early receive of jumbo frames) is probed
later. Change the DMA latency requirement to be per-interface if needed
instead of per driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e1000_clear_hw_cntrs_*() functions read the registers to clear them.
There is no reason to save the register contents so the temp variable can
be removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set booleans to 'true' or 'false' to make it clear it is a boolean. Also
change instances of TRUE/FALSE in comments to lowercase true/false.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy and nvm operations structures have function pointers that contain
"phy" and "nvm" in the pointer names which are redundant since the
structures are already obviously in phy and nvm structures.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch depends on a previous one that cleans up redundant #includes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was only updating MII stats when an LSC up was detected and
the interface had not already been reported up to netdev. This meant
MII stats returned in response to an SIOCGMIIREG ioctl would always
show a link up if it had ever been up. This was misleading the networking
daemon guessnet, which uses this ioctl, into making improper network port
selections.
This fix adds a call to e1000_phy_read_status() to actively read the
mii stats before responding to the SIOCGMIIREG ioctl.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing the ethtool PHY loopback test on PCH-based LOMs (82577 and
82578), disable K1 (a MAC-PHY interconnect low power mode) otherwise
packets might get corrupted.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e1000_get_cable_length_82577() should return a negative value upon
error.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copper links with WoL or management enabled (any condition which prevents
the phy from being powered down when the interface is taken down) were
always reporting link-up when the interface had been taken down. This
is because when the interface is taken down (ifconfig ethx down),
interrupts are disabled. With no interrupts, there is no LSC interrupt,
which is normally required to set "get_link_status", which instructs the
driver to query the device for link state. The fix is to force
get_link_status to true if the interface is not up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using legacy interrupts, do not clean the Rx ring while resetting
otherwise traffic will not pass.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide missing function pointers for ethtool set/get offloads.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing the interrupt timers following an IMS clear has the unwanted
side-effect of flushing all descriptors immediately following a partial
write when interrupts are disabled.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tests for 82583 in a couple ethtool functions that were missed from the
initial hardware enablement submission.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting WoL feature, check the supplied modes are all supported rather
than checking for no support. This way, if any new modes are added the
driver does not default to not complaining about it if we don't really
support it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please apply patch to update redboot section while firmware update. Code
checks if section needs to be updated before actually doing it.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BIT for macro definitions wherever possible, remove
unused and redundant macros.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Summary of Changes:
-Fix to receive multicast packets by setting the corresponding hardware
bit during initialization.
-Fix to re-enable the interface [by interface up command(ifup)] while the
interface is down.
-Fix to be able to down the interface by passing the last parameter
correctly to request_irq().
-Remove to read 4 extra bytes from the receiving queue after reading a
packet, even though it does not cause a predictable issue now.
-Remove occurrences of transmission done interrupt in order to tx
throughput enhancement.
-Enable IP checksum for packet receiving by setting the corresponding
hardware bit during initialization.
-Relocate ks_enable_int()/ks_disable_int() in order not to declare those
functions at the beginning of the file.
-Rename ks_enable()/_disable() to ks_enable_qmu()/ks_disable_qmu() in
order to give more meaningful names and relocate them not declaire
those functions at the beginning of the file.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building for Sun 3:
drivers/net/ethoc.c:1091: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `ethoc_probe':
drivers/net/ethoc.c:965: undefined reference to `dma_alloc_coherent'
drivers/net/ethoc.c:1063: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring the OEM bits in the PHY on 82577/82578, do not restart
autonegotiation if the firmware is blocking it (e.g. when an IDE-R session
is active) because the link must not go down.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A workaround for pre-release versions of 82577 is causing link issues on
some switches. The workaround is no longer needed on production parts so
remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing MTU, save it off prior to resetting otherwise the flow control
thresholds may be miscalculated.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some devices (e.g. 82578) not having a Tx timeout factor when linked at
100Mbps can cause false reports of hardware hangs on busy hubs.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When flow control (pause) parameters were changed via ethtool (i.e. enabled
or disabled), the newly calculated thresholds were not being written to the
device for non-fiber media.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary workaround that mistakenly does not perform a page
select operation for PHY registers 29 and 30 (assuming these are the PHY
debug port address and data registers) on 82578 which can cause reads
of the Transmit with No Carrier Sense statistics register on page 778 to be
read from an incorrect page. Also error out if the page select operation
fails.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ec2a2b80f broke Tx/Rx when using
jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged
once the high water mark was reached preventing normal packet traffic).
This patch reverts the breakage and sets appropriate high and low water
marks of the Rx FIFO for 82577/82578 which require a workaround due to a
flow control issue in hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc is required by CONFIG_IXGBE_DCB.
This also fixes compilation warning:
drivers/net/ixgbe/ixgbe_main.c: In function ‘ixgbe_tx_is_paused’:
drivers/net/ixgbe/ixgbe_main.c:245: warning: unused variable ‘tc’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove PCI vendor and device IDs for QLE8240 and QLE8242
CNA devices. CNA devices will have separate driver.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of the 82580 PHY and MAC support added and adds a set
of supported device IDs for said hardware.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 82580 MAC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the phy included in the 82580 silicon family.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
veth_get_stats() can be called in parallel on several cpus.
It's better to not reset dev->stats as it could give wrong result on
one cpu. Use temporary variables, then store the final results.
Also, we should loop on every possible cpus, not only online cpus,
or cpu hotplug can suddenly give wrong veth stats.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed function pointer use from non-majority address-of style
to majority short form without & via: (was: 8 with &, 36 without)
grep -rPl "\btasklet_init\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \
perl -i -e 'local $/; while (<>) { s@(\btasklet_init\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\
done
Compile tested allyesconfig x86
Signed-off-by: Joe Perches <joe@perches.com>
drivers/net/cnic.c | 4 ++--
drivers/net/jme.c | 10 +++++-----
drivers/net/skge.c | 2 +-
3 files changed, 8 insertions(+), 8 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now all frames mac80211 hands to the driver
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set to
request TX status. This isn't really necessary, only
the injected frames need TX status (the latter for
hostapd) so move setting this flag.
The rate control algorithms also need TX status, but
they don't require it.
Also, rt2x00 uses that bit for its own purposes and
seems to require it being set for all frames, but
that can be fixed in rt2x00.
This doesn't really change anything for any drivers
but in the future drivers using hw-rate control may
opt to not report TX status for frames that don't
have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com> [rt2x00 bits]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not as fancy as coccinelle. Checkpatch errors ignored.
Compile tested allyesconfig x86, not all files compiled.
grep -rPl --include=*.[ch] "\brequest_irq\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \
perl -i -e 'local $/; while (<>) { s@(\brequest_irq\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\
done
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
cxgb3: fix premature page unmap
ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts
vlan: Fix register_vlan_dev() error path
gro: Fix illegal merging of trailer trash
sungem: Fix Serdes detection.
net: fix mdio section mismatch warning
ppp: fix BUG on non-linear SKB (multilink receive)
ixgbe: Fixing EEH handler to handle more than one error
net: Fix the rollback test in dev_change_name()
Revert "isdn: isdn_ppp: Use SKB list facilities instead of home-grown implementation."
TI Davinci EMAC : Fix Console Hang when bringing the interface down
smsc911x: Fix Console Hang when bringing the interface down.
mISDN: fix error return in HFCmulti_init()
forcedeth: mac address fix
r6040: fix version printing
Bluetooth: Fix regression with L2CAP configuration in Basic Mode
Bluetooth: Select Basic Mode as default for SOCK_SEQPACKET
Bluetooth: Set general bonding security for ACL by default
r8169: Fix receive buffer length when MTU is between 1515 and 1536
can: add the missing netlink get_xstats_size callback
...
Enforce all device constraints on the descriptor memory region.
There are several constraints on the descriptor memory, as documented
in the specification. The current code does not enforce them and/or
incorrectly enforces them.
Those constraints are:
- The address limitations on 30/32bit engines, that also apply to
the skbs.
- The 4k alignment requirement on 30/32bit engines.
- The 8k alignment requirement on 64bit engines.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_esbq_exec’:
drivers/net/wireless/wl3501_cs.c:387: warning: ‘tmp’ is used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:384: note: ‘tmp’ was declared here
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 supports also that NVS is stored in a separate EEPROM, add support
for that.
kvalo: use platform data instead Kconfig and use kernel style
Signed-off-by: David-John Willis <John.Willis@Distant-earth.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes warnings:
drivers/net/wireless/wl12xx/wl1251_rx.c: In function 'wl1251_rx_status':
drivers/net/wireless/wl12xx/wl1251_rx.c:75:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:77:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:77:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:77:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:78:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:78:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
drivers/net/wireless/wl12xx/wl1251_rx.c:78:
warning: 'qual' is deprecated (declared at include/net/mac80211.h:555)
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to IEEE80211 standard all the data packets have to be sent with
TODS bit set. This patch fixes the null data packet format which was sent
without TODS bit set. This should fix many problems associated with
power save. Janne Ylalehto also found this fix in the same time as mine,
for a different bug he was working on.
Signed-off-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases, the IRQ loop handler could acknowledge an interrupt to
the chipset, but not service it.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Filter out unwanted events to reduce wakeups.
Signed-off-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for IRQ looping. Helps in the case that we have e.g. multiple
packets coming from the network when we wake up from the ELP.
Signed-off-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch increases the number of beacons to be missed before generating
SYNC TIMEOUT event. It increases the beacon timeout period to 500
microseconds, which gives enough time for the firmware to receive probe
response or beacon. Also handled the regain event from firmware once it
receives a probe response or beacon.
Signed-off-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets the dtim period obtained from the mac80211 to firmware.
Signed-off-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dtim period obtained from the mac80211 is not set to the firmware.
This patch implements the acx command to set correct tbtt and dtim value
to the firmware.
Signed-off-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ps-poll template aid bits 14 and 15 were not masked as required by the
standard. Mask them so that aid is sent in correct format.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Earlier firmware was stored to a memory area allocated with kmalloc()
but finding a a contiguous area of memory long enough for the firmware is
very difficult in certain cases. better to allocate the memory for firmware
with vmalloc() instead and use a small buffer for DMA transfers.
Thanks to Eero Tamminen for the idea.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement (slightly) delayed entry into ELP. This will cure several
problems:
- It works around a firmware race condition if ELP is entered too fast
after commands (resulting in ELP timeout -traces)
- It will reduce the number of sleep-wake cycles between already
scheduled events such as interrupts and tx, hence improving
performance (less delay in switching between RX and TX)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable beacon filtering when PSM is enabled
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable beacon filtering with the mac80211 stack.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add configuration for connection monitor (number of allowed beacons, and
timeout after last received beacon.)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At least two revisions of the D-Link DWA 160 exist, called A1 and A2. A1
(USB-ID 07d1:3c10) is already listed in usb.c as D-Link DWA 160A. A2
(USB-ID 07d1:3a09) works if added to ar9170_usb_ids. I didn't do much
testing until now, but I was able to connect to APs using WPA or WEP and
transmit data.
Summary:
* Add model revision number to the comment for D-Link DWA 160 A1 (07d1:3c10)
* Add support for D-Link DWA 160 A2 (07d1:3a09)
Signed-off-by: Thomas Klute <thomas2.klute@uni-dortmund.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
taken from windows inf file (09/15/2009, 1.04.07.0000)
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The entire aggregation code currently operates on the
hw pointer and station addresses, but that needs to
change to make stations purely per-vif; As one step
preparing for that make the aggregation code callable
with the station, or by the combination of virtual
interface and station address.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for AR5416 ver 1.0 before calibrating 3 chains
for multi-chain. This is a WAR for calibration
failure.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ATH9K_ANT_VARIABLE is the default diversity control used.
Consequently ath9k_hw_decrease_chain_power() does nothing.
ath9k_hw_setantennaswitch() is unused too.
Also, gbeacon_rate is unused.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
axq_linkbuf, axq_aggr_depth, axq_lastdsWithCTS and
axq_gatingds are unused.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Remove a code chunk dealing with operating mode changes.
As noted, all such policy changes are to be done in
add_interface.
* Remove pointless check for empty BSSID.
Also, remove mode checks - mac80211 does all the needed checks.
* Handle enabling/disabling beacon transmission properly.
* Handle beacon interval changes for AP mode.
The original code depended on config_interface() to update
the HW TSF. Since that callback has been removed, handle
it properly.
* Remove unneeded code dealing with key/privacy.
* Set the chainmasks to 1x1 for IBSS when the BSSID is set.
This was happening uncondionally before.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the need for separately allocated private tx info
data in ath9k and brings the driver one small step closer to using the
mac80211 rate control API properly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables the driver to process all incoming
dupofdm-modulated frames when operating in HT40 mode.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also regroup CSR_EEPROM and CSR_OTP bit field definitions.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the new mac80211 functionality, this makes
iwlwifi handle unicast PS buffering correctly.
The device works like this:
* when a station goes to sleep, the microcode notices
this and marks the station as asleep
* when the station is marked asleep, the microcode
refuses to transmit to the station and rejects all
frames queued to it with the failure status code
TX_STATUS_FAIL_DEST_PS (a previous patch handled
this correctly)
* when we need to send frames to the station _although_
it is asleep, we need to tell the ucode how many,
and this is asynchronous with sending so we cannot
just send the frames, we need to wait for all other
frames to be flushed, and then update the counter
before sending out the poll response frames. This
is handled partially in the driver and partially in
mac80211.
In order to do all this correctly, we need to
* keep track of how many frames are pending for each
associated client station (avoid doing it for other
stations to avoid the atomic ops)
* tell mac80211 that we driver-block the PS status
while there are still frames pending on the queues,
and once they are all rejected (due to the dest sta
being in PS) unblock mac80211
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This field was marked as reserved before since we didn't
use it, but is present in all released firmwares afaict.
We're going to need it soon, so add it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a frame is sent to a sleeping station, the
microcode reports TX_STATUS_FAIL_DEST_PS as its
status -- we need to translate that to the flag
that mac80211 expects.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle BSS_CHANGED_BEACON_ENABLED to enable the sending
of beacons. Also set the correct HT RXON and QoS config.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending beacon commands to the uCode, we must
inform it of the offset in the beacon frame of the
TIM Element so it can transmit packets from the
correct queue. This functionality is implemented
in iwl_set_beacon_tim().
Fix a bug setting the rate_n_flags for the beacon
packet. First, it should not use the station table's
rate (it's a management frame), and second it needs
to properly configure the TX antennas.
Finally, also, clean up and comment relevant functions.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A recent change optimized the power usage by the device by only powering it
up during EEPROM load if it is required (for OTP devices). This change causes
an error on the 1000 series devices during module load.
The error looks as follows:
[ 1624.024524] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds
[ 1624.024527] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[ 1624.024711] iwlagn 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1624.024749] iwlagn 0000:01:00.0: setting latency timer to 64
[ 1624.024909] iwlagn 0000:01:00.0: Detected Intel Wireless WiFi Link 1000 Series BGN REV=0x6C
[ 1624.081263] iwlagn 0000:01:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080003D8
[ 1624.092967] iwlagn 0000:01:00.0: OTP is empty
[ 1624.092988] iwlagn 0000:01:00.0: Unable to init EEPROM
[ 1624.093033] iwlagn 0000:01:00.0: PCI INT A disabled
[ 1624.093065] iwlagn: probe of 0000:01:00.0 failed with error -2
Adding a dump_stack() to where that error is printed shows the following:
[ 1624.024524] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds
[ 1624.024527] iwlagn: Copyright(c) 2003-2009 Intel Corporation
[ 1624.024711] iwlagn 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1624.024749] iwlagn 0000:01:00.0: setting latency timer to 64
[ 1624.024909] iwlagn 0000:01:00.0: Detected Intel Wireless WiFi Link 1000 Series BGN REV=0x6C
[ 1624.081263] iwlagn 0000:01:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080003D8
[ 1624.081263] Pid: 3073, comm: work_for_cpu Tainted: G W 2.6.31.5 #4
[ 1624.081263] Call Trace:
[ 1624.081263] [<ffffffffa02395db>] T.726+0x22b/0x420 [iwlcore]
[ 1624.081263] [<ffffffffa023985a>] iwlcore_eeprom_acquire_semaphore+0x8a/0x190 [iwlcore]
[ 1624.081263] [<ffffffff81110c94>] ? __kmalloc+0x194/0x1c0
[ 1624.081263] [<ffffffffa02391f5>] ? iwlcore_eeprom_verify_signature+0x25/0xf0 [iwlcore]
[ 1624.081263] [<ffffffffa0239c67>] iwl_eeprom_init+0x107/0xf40 [iwlcore]
[ 1624.081263] [<ffffffffa026ab9c>] ? iwl_prepare_card_hw+0x11c/0x470 [iwlagn]
[ 1624.081263] [<ffffffff8127e2a4>] ? pci_bus_write_config_byte+0x64/0x80
[ 1624.081263] [<ffffffffa026b1f8>] iwl_pci_probe+0x308/0xac0 [iwlagn]
[ 1624.081263] [<ffffffff810710a0>] ? do_work_for_cpu+0x0/0x30
[ 1624.081263] [<ffffffff81284912>] local_pci_probe+0x12/0x20
[ 1624.081263] [<ffffffff810710b3>] do_work_for_cpu+0x13/0x30
[ 1624.081263] [<ffffffff81075826>] kthread+0xa6/0xb0
[ 1624.081263] [<ffffffff81012fea>] child_rip+0xa/0x20
[ 1624.081263] [<ffffffff81075780>] ? kthread+0x0/0xb0
[ 1624.081263] [<ffffffff81012fe0>] ? child_rip+0x0/0x20
[ 1624.092967] iwlagn 0000:01:00.0: OTP is empty
[ 1624.092988] iwlagn 0000:01:00.0: Unable to init EEPROM
[ 1624.093033] iwlagn 0000:01:00.0: PCI INT A disabled
[ 1624.093065] iwlagn: probe of 0000:01:00.0 failed with error -2
We know that the routines in this trace, iwlcore_eeprom_acquire_semaphore
and iwlcore_eeprom_verify_signature, only access CSR registers and thus do
not need the device to be awake if it is EEPROM. But for OTP it is required
for the device to be awake to read these registers. Ensure device is awake
before accessing these registers.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Align the format for tx_statistics and rx_statistics debugfs output for
better readability
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In both 6x00 and 6x50 series, the enhanced/extended tx power table in
EEPROM is used to set the max. tx power limit.
This new tx power table is in 1/2 dBm format, which creates an issue of
possibility of 1/2 dBm loss when driver set the tx power limit; because
of driver keep track and report the tx power in dBm format.
In order to prevent the 1/2 dBm loss, keep track of the true max tx
power in 1/2 dBm format in driver; do the comparison and adjust the tx
power if needed when send tx power command to uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Power-saving logic will not re-issue a POWER_TABLE_CMD if a new command
matches the prior one. This can be bad if we re-start the device due to
e.g. uCode error; the new POWER_TABLE_CMD (required to invoke power-saving)
may match the prior POWER_TABLE_CMD issued before the uCode error.
Ensure the POWER_TABLE_CMD is sent to device when uCode is up.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issue REPLY_STATISTICS_CMD to uCode, two possible flag
can be set in the configuration flags
bit 0: Clear statistics
0: Do not clear Statistics counters
1: Clear to zero Statistics counters
Allow "clear" parameter to be set from the caller.
Add debugfs file to clear the statistics counters to help monitor and
debug the uCode behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Number of data structure for 6000 series no longer in production, the
data structure already being removed; also need to remove the external
reference define in iwl-dev.h
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drop the non-production PCI-IDs for 6x50 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Number of HT40 power parameters are not used; remove those from
iwl_channel_info data structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Temporary disable the coex function for wifi/wimax for 6x50
series until the full implementation ready.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Validate enhanced tx power entry read from EEPROM before applying the
tx power value. Different versions of EEPROM might contain different size
of table; always a good idea to make sure the entry is valid before
applying to the targeted channel.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this file, function names are otherwise used as pointers without &.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
unmap Rx page only when guaranteed that this page won't be
used anymore to allocate rx page chunks.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TRT bit shifts were reversed for EMAC4 and non-EMAC4 during the
port from ibm_emac to ibm_newemac. This patch corrects that error.
Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com>
Acked-by: Feng Kan <fkan@appliedmicro.com>
Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow MAC address to be changed even if device is not up.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With multi queue devices, its possible that several cpus call
macvlan RX routines simultaneously for the same macvlan device.
We update RX stats counter without any locking, so we can
get slightly wrong counters.
One possible fix is to use percpu counters, to get precise
accounting and also get guarantee of no cache line ping pongs
between cpus.
Note: this adds 16 bytes (32 bytes on 64bit arches) of percpu
data per macvlan device.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
znet was including "wireless/i82593.h" (which is a bit wierd), and I
missed that when I relocated i82593.h to drivers/staging/wavelan. Since
I don't have ISA turned-on in my normal .config, I didn't see the build
failures -- mea culpa!
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to look for the 'shared-pins' property to get
this right.
Based upon a patch by Hermann Lauer.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes config dependency on x86 to build vmxnet3 driver. Thus
the driver can be built on big endian architectures now. Although vmxnet3
is not supported on VMs other than x86 architecture, all this code goes in
to ensure correctness. If the code is not dependent on x86, it should not
assume little endian architecture in any of its operations.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put Tx and Rx DPC to be handled in the NAPI:
- Saves status blocks.
- Moves the Tx work from hardIRQ to NAPI.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following warning:
WARNING: drivers/net/phy/built-in.o(.devexit.text+0x70): Section mismatch in reference from the function .mdio_gpio_bus_destroy() to the function .devinit.text:.mdio_gpio_bus_deinit()
The function __devexit .mdio_gpio_bus_destroy() references
a function __devinit .mdio_gpio_bus_deinit().
This is often seen when error handling in the exit function
uses functionality in the init path.
The fix is often to remove the __devinit annotation of
.mdio_gpio_bus_deinit() so it may be used outside an init section.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. This patch is based on the kernel of 2.6.32-rc7
2. In this patch, we enlarge the out buffer size to optimize the
upload speed for the ppp connection. Then it can support the upload of
HSUPA data cards.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- move Kconfig entries to the subdirectory
- do remaining renames of mpc52xx to mpc5xxx
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all hardcoded values have been replaced as this made the code quite
unreadable. IMHO this compromise serves the purpose of readability.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge two functions into one. The result is smaller as they can now share some
variables.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- use extern where apropriate
- don't export symbols
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- remove whitespaces
- use ! and ?: when apropriate
- make braces consistent
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ks8695_rx() will call refill_buffers() for every incoming packet.
Its not necessary. We just need do it after finishing receiving thing.
And the 'RX dma engine' is in the same situation.
This blocks our user space application. The following patch may fix it.
Signed-off-by: zeal <zealcook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ks8695 rx irq is edge-level. Before arriving at irq handler, the
corresponding status bit has been clear(irq's ack).
So we should not check it after that.
Signed-off-by: zeal <zealcook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP does not correctly call pskb_may_pull() on all necessary receive paths
before reading the PPP protocol, thus causing PPP to report seemingly
random 'unsupported protocols' and eventually trigger BUG_ON(skb->len <
skb->data_len) in skb_pull_rcsum() when receiving multilink protocol in
non-linear skbs.
ppp_receive_nonmp_frame() does not call pskb_may_pull() before reading the
protocol number. For the non-mp receive path this is not a problem, as
this check is done in ppp_receive_frame(). For the mp receive path,
ppp_mp_reconstruct() usually copies the data into a new linear skb.
However, in the case where the frame is made up of a single mp fragment,
the mp header is pulled and the existing skb used. This skb was then
passed to ppp_receive_nonmp_frame() without checking if the encapsulated
protocol header could safely be read.
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commmit 4b77b0a2ba EEH breaks
after the second error, since it calls pci_restore_state()
but it returns 0, since pci->state_saved is false.
So, this patch just call pci_save_state() after pci_restore_state().
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a holdover from earlier code when we used to set
the power limit to '0' after a reset to configure the
default transmit power, ath5k interprets txpower=0 as
12.5 dBm. Fix that by just passing 0 through.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=14567
Cc: stable@kernel.org
Reported-by: Daniel Folkers <daniel.folkers@task24.nl>
Tested-by: Daniel Folkers <daniel.folkers@task24.nl>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wlan didn't know about NL80211_AUTHTYPE_AUTOMATIC and simple
setup with 'iwconfig wlan essid no-encrypt' would fail (ENOSUPP).
v2: use NDIS_80211_AUTH_AUTO_SWITCH instead of _OPEN.
This will make device try shared key auth first, then open.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Please be gentle, I'm a fs developer and this is my first foray into drivers, as
I'm tired of building ralinks driver everytime I update my kernel. Whenever I
load the rt2800pci driver my box bogs down, and a few printk's later I
discovered its because I was getting 10's of thousands of TBTT interrupts a
second. I discovered this was because we were setting the beacon timer to 0,
which is apparently what TBTT keys off of. It seems to me that we should only
be enabling TBTT when we are in a beacon transmitting mode, which from what I
can tell is in AD-HOC and other such modes where the mac80211 layer would have
given us a proper beacon_int to set the beacon timer to instead of 0. So this
is my fix, only enable TBTT if our sync mode is for beacon. This makes it so my
box doesn't die everytime I load the rt2800pci driver. Let me know if this is
acceptable, I just learned all these terms about 15 minutes ago via wikipedia,
so I really am not familiar with how this stuff is supposed to work. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression introduced in
"ath9k: avoid the copy skb->cb on every RX'd skb"
With that change, the rx status in skb->cb was left uninitialized
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current tree hits a BUG_ON in rt2x00_regbusy_read, because the eFuse EEPROM
reading code of rt2800lib uses the function without the csr_mutex locked.
Fix this by locking the csr_mutex for the of the EEPROM reading cycly and
using the _lock variants of the register reading and writing functions.
This also introcudes the register_read_lock function pointer in the
rt2800_ops structure.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers (rt2800* most notably) cannot set the RF and RT chipset in
the correct order to have the information logging in rt2x00_set_chip
be correct.
Fix this by decoupling the setting of the chipset information from the
logging of the chipset information so that drivers can determine
themselves when all information is set.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure RF302x and RF2020 chipsets are handled properly in rt2800lib
for the rt3090 chipset.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mirror the legacy Ralink driver with respect to rt2800 RF register
programming. Execute rt2800_config_channel_rt3x for all RF2020,
RF3020, RF3021 & RF3022 chipsets when operating on RT3070 devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The language of 802.3ad 43.4.9 requires the "recordPDU" function
to, in part, compare the Partner parameter values in a received LACPDU
to the stored Actor values. If those match, then the Partner's
synchronization state is set to true.
The current 802.3ad implementation is performing these steps out
of order; first, the synchronization check is done, then the paramters are
checked to see if they match (the synch check being done against a match
check of a prior LACPDU). This causes delays in establishing aggregators
in some circumstances.
This patch modifies the 802.3ad code to call __choose_matched,
the function that does the "match" comparisions, as the first step of
__record_pdu, instead of immediately afterwards. This new behavior is
in compliance with the language of the standard.
Some additional commentary relating to code vs. standard is also
added.
Reported by Martin Patterson <martin@gear6.com> who also supplied
the logic of the fix and verified the patch.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the NAPI poll function(emac_poll), check for netif_running()
is unnecassary. In addition to associated runtime overhead, it
also results in a continuous softirq loop when the interface is
brought down under heavy traffic(tested wit Traffic Generator).
Once the interface is disabled, the poll function always returns
zero(with the check for netif_running) and napi_complete() would
never get called resulting in softirq loop.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the NAPI poll function, check for netif_running() is unnecassary.
In addition to associated runtime overhead, it also results in
continuous softirq loop when the interface is brought down under heavy
traffic(tested with Traffic Generator).Once the interface is disabled,
the poll function always returns zero(with the check for netif_running)
and napi_complete() would never get called resulting in softirq loop.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.104.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the 5717 variant device ID enumerations and adds those
DIDs to the PCI ID table.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to funnel each MSI-X vector's rx packet buffers
into a single set of producer rings which will then be submitted to the
hardware.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx producer mailbox registers are used in several spots in the code.
The addition of TG3_64BIT_REG_LOW makes register references
uncomfortably long. This patch creates an alias for the standard and
jumbo ring producer index registers to make the code cleaner.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch increases the number of producer rings available and
implements the constructor and destructor code that deals with them.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes how the code uses the rx_std_prod_idx member. In the
following patch, the code will be changed so that it will act just like
a hardware mailbox. This patch prepares the code so that memory barriers
can be more easily inserted.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Magnus Damm