With compat-wireless CR* macros in zd_usb.h conflict with CR macros in
include/asm-generic/termbits.h. So rename CR* macros to ZD_CR*.
Conversion was done with using sed and then 'over 80 character line'
checkpatch.pl warnings and comment indents were fixed.
Reported-by: Walter Goldens <goldenstranger@yahoo.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2.6.38 added WARN_ON(in_irq) in del_timer_sync that triggers on zd1211rw when
reseting rx idle timer in urb completion handler.
Move timer reseting to tasklet.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch removes the bogus flag introduced by upstream commit
eefdbec1ea. Old code had buffer length check
that new code tried to handle with URB_SHORT_NOT_OK flag. With USB debugging
enabled bogus flag caused usb_submit_urb fail.
Remove URB_SHORT_NOT_OK flag and add buffer length check to urb completion
handler.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32092
Reported-by: Jonathan Callen <abcd@gentoo.org>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.
Make asynchronous zd_usb_iowrite16v_async available outside zd_usb.c
and use where possible.
This lower CPU usage from ~10% to ~2% on Intel Atom when running
AP-mode with 100 TU beacon interval.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.
This patch makes zd_usb_iowrite16v use asynchronous urb submit within
zd_usb.c. zd_usb_iowrite16v_async_start is used to initiate writing
multiple commands to device using zd_usb_iowrite16v_async. Each URB
is delayed and submitted to device by next zd_usb_iowrite16v_async
call or by call to zd_usb_iowrite16v_async_end. URBs submitted by
zd_usb_iowrite16v_async have URB_NO_INTERRUPT set and last URB
send by zd_usb_iowrite16v_async_end does not. This lower CPU
usage when doing writes that require multiple URBs.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211rw is using usb_bulk_msg() with usb_sndbulkpipe() on interrupt endpoint.
However usb_bulk_msg() internally corrects this and makes interrupt URB.
It's better to change usb_bulk_msgs in zd1211rw to usb_interrupt_msg for less
confusion.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX appears to freeze while idle. Resetting rx-urbs appears to be enough to fix
this. Do reset 30 seconds after last rx.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing transfers at high speed for long time, tx queue can freeze. So add
tx watchdog. TX-watchdog checks for locked tx-urbs and reset hardware when
such is detected. Merely unlinking urb was not enough, device have to be
reseted. Hw settings are restored so that any open link will stay on after
reset.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Device command timeouts are set up very high (1 sec) and this causes
AP beacon to lock up for long for example. Checking timeouts on device
it's easy to see that 1 sec timeout is not needed, when device fails
to response longer timeout doesn't help:
[ 473.074419] zd1211rw 1-1:1.0: print_times() Read times:
[ 473.175163] zd1211rw 1-1:1.0: print_time() 0 - 10 msec: 1506
[ 473.176429] zd1211rw 1-1:1.0: print_time() 11 - 50 msec: 0
[ 473.177955] zd1211rw 1-1:1.0: print_time() 51 - 100 msec: 0
[ 473.180703] zd1211rw 1-1:1.0: print_time() 101 - 250 msec: 0
[ 473.182101] zd1211rw 1-1:1.0: print_time() 251 - 500 msec: 0
[ 473.183221] zd1211rw 1-1:1.0: print_time() 500 - 1000 msec: 20
[ 473.184381] zd1211rw 1-1:1.0: print_time() 1000 - ... msec: 18
Also vendor driver doesn't use this long timeout. Therefore change
timeout to 50msec.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As might lower beacon update CPU usage.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use stack for allocing small < 64 byte arrays in zd_chip.c and preallocated
buffer in zd_usb.c. This might lower CPU usage for beacon setup.
v2:
- Do not use stack buffers in zd_usb.c as they would be used for urb
transfer_buffer.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When stress testing AP-mode I hit OOPS when unpluging or rmmodding
driver.
It appears that when tx-queue is disabled, tx-urbs might be left pending.
These can cause ehci to call non-existing tx_urb_complete() (after rmmod)
or uninitialized/reseted private structure (after disconnect()). Add skb
queue for submitted packets and unlink pending urbs on zd_usb_disable_tx().
Part of the problem seems to be usb->free_urb_list that isn't always
working as it should, causing machine freeze when trying to free the list
in zd_usb_disable_tx(). Caching free urbs isn't what other drivers seem
to be doing (usbnet for example) so strip free_usb_list.
Patch makes tx-urb handling saner with use of urb anchors.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Yasuhiro ABE <yadiary@gmail.com> reported success in sourceforge zd1211-dev list.
The device is a NEC Aterm WL54GU usb wireless stick.
The brand and retail product name
NEC, Aterm PA-WL54GU
The USB ID's (duh)
ID 0409:0248
The chip ID string
zd1211rw 1-1:1.0: zd1211b chip 0409:0248 v4810 high 00-1b-8b AL2230S_RF pa0 g--N-
The FCC ID
unknown
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Yasuhiro ABE <yadiary@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The zd1211rw always assumed that the storage device is at endpoint 1,
but there are devices (Spairon Homelink 1202) that are at endpoint 0.
Try both, starting with 1 to make sure to not break existing setups.
Signed-off-by: Stefan Seyfried <seife@sphairon.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
First, we reduce the number of hardware retries to 0 (ie 2 real retries
for each rate). Next, when we report the retries to mac80211, we always
report a retry count of 1 (it seems to be 2 in fact, but using 2 seems
to lead to wrong performance for some reason). We use a state machine to
determine the real fate of a packet based on the 802.11 ACK and what the
Zydas hardware is saying when a real retry occurs. The real retry rates
are encoded in a static array. It has been tested with both zd1211 and
zd1211b hardware. Of course, since the Zydas hardware is not reporting
retries accurately, we are just doing our best in order to get the best
performance (ie higher throughput).
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the usb_endpoint_dir_out API function. Note that the use of
USB_TYPE_MASK in the original code is incorrect; it results in a test that
is always false.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
struct usb_endpoint_descriptor *endpoint;
expression E;
@@
- (endpoint->bEndpointAddress & E) == USB_DIR_OUT
+ usb_endpoint_dir_out(endpoint)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New device supported by the zd1211rw driver reported to linux-wireless.
Device string from lsusb:
"ID 083a:e501 Accton Technology Corp. ZD1211B"
RF type from dmesg:
zd1211b chip 083a:e501 v4810 high 00-1a-2a AL2230_RF pa0 g--NS
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Adrián Cereto<ssorgatem@esdebian.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the past ids were inserted in no particular order and it has
become hard to see what ids are already included or not. This
patch sorts the ids by numerical value and has no functional effect.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yevgen Kotikov reported success on the sourceforge zd1211-devs list
with the following details:
Brand/retail: SONY IFU-WLM2
USB-IDs: Vendor: 0x054C Device: 0x0257
chip ID: zd1211b chip 054c:0257 v4802 high 00-0b-6b AL2230_RF pa0 -----
FCC ID: unknown
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Yevgen Kotikov <yevgen.kotikov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a shuttle machine here we got 07b8:6001 device, handled by zd1211rw, which does not work.
Scanning is OK but association does not work, we get "direct probe to AP xxx timed out"
It appears that this simple patch makes the device work perfectly.
This id was already there in initial import of the driver so I don't know if it has ever been
working as ZD1211 (which would mean they changed it and kept the id :( ).
Signed-off-by: Pascal Terjan <pterjan@mandriva.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hans Pontar reported success on the sourceforge zd1211-devs mailing list.
The device is branded "Arcor Easy Stick A 50 WLAN" (device manufactured
by SMC for a German ISP - SMC model name: WN4501H-LF-IR). General
information and Windows driver are available under (German only):
http://www.arcor.de/hilfe/neu/index.php?sid=&aktion=anzeigen&rubrik=004018140&id=487
Device details:
USB-IDs: Vendor: 0x083A Device: 0xE503
Chip ID: zd1211b chip 083a:e503 v4810 high 00-1d-19 AL2230S_RF pa0 g--N-
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Hans Pontar <pontar@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de> reported success
in the sourceforge zd1211 mailing list on this addition. This product ID
was supported by the vendor driver ZD1211LnxDrv 2.22.0.0 (and possibly
earlier) and it probably should have been added earlier.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Giuseppe Cala <jiveaxe@gmail.com> (The second "a" in "Cala" should be
a grave, U+00E0) reported success on zd1211-devs@lists.sourceforge.net.
The chip info is:
zd1211b chip 0df6:0036 v4810 high 00-0c-f6 AL2230_RF pa0 g--N-
The Sitecom WL-603 is detected as a zd1211b with a AL2230 RF transceiver chip.
Signed-off-by: Giuseppe Cala <jiveaxe@gmail.com>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
In drivers/net/wireless/zd1211rw/zd_usb.c the code:
(endpoint->bEndpointAddress & USB_TYPE_MASK) == USB_DIR_OUT
is suspicious. If it is intended to use USB_ENDPOINT_DIR_MASK rather than
USB_TYPE_MASK, then the whole conditional test could be converted to a call
to usb_endpoint_is_bulk_in.
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
07fa/1196
Bewan BWIFI-USB54AR: Tested by night1308, this device is a ZD1211B with
an AL2230S radio.
0ace/b215
HP 802.11abg: Tested by Robert Philippe
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
akpm: taken from http://bugzilla.kernel.org/show_bug.cgi?id=11587
I bought the wifi dongle trust nw-3100 wich is in fact a zd1211rw. Its
hardware id was missing in the sources, adding it made it work flawlessly.
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I would like to inform you of our zd1211 based usb wifi adapter (AirTies
WUS-201), which works with the zd1211rw driver with the following device
id definition.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The zd1211rw driver uses unaligned stack buffer for USB control
message. But it might cause stack corruption on non-coherent
platform, such as MIPS. Use DMA-aware buffers for USB transfer.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd_mac_tx_to_dev() could potentially free the skb, or hand it off
to mac80211 which might free it. Hence, this code needs to get the
usb pointer out of skb->cb before handing it off to that function.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previously unused CR_CAM_MODE register is set to MODE_AP_WDS. This makes the
driver ack mesh (WDS) frames. It does not affect Infra functionality of the
driver.
Previously missing beaconing support has been added. This might also help
implement a currently missing ah-hoc mode.
Support for interrupts from the device have been added, but we are not handling
most of them.
Mesh interfaces are considered associated as long as the interface is up.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by chloubs on IRC
zd1211 chip 157e:300a v4810 high 00-11-e0 AL7230B_RF pa0 g----
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville