The i.MX USB controller may drive the usb power line directly, but the
polarity depends on the board. Reset state of the polarity is low-active so
add this property to allow it to be high-active.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The status quo on i.MX6 is that if "over-current-active-high" is
specified in the device tree this is configured as expected. If
the property is missing polarity isn't changed and so the
polarity is kept as setup by the bootloader. Reset default is
active high, so active low can only be used with help by the
bootloader. On i.MX7 it is similar, but there disabling of
over current detection has a similar inconsistency.
This patch introduces a new property that allows to explicitly
configure for active low over current detection and consistently
sets this up. In the absence of an explicit configuration the
bit is kept as is. On i.MX7 over current detection is used unless
disabled in the device tree.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
For USB HSIC, the data and strobe pin needs to be pulled down
at default, we consider it as "idle" state. When the USB host
is ready to be used, the strobe pin needs to be pulled up,
we consider it as "active" state.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Some hardware implementations require to configure pins differently
according to the USB role (host/device), this can be an update of the
pins routing or a simple GPIO value change.
This patch introduces new optional "host" and "device" pinctrls.
If these pinctrls are defined by the device, they are respectively
selected on host/device role start.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The chipidea usb controller may be connected, in some platforms,
to an external mux to toggle between different usb ports for
different roles (host and device).
The mux-controller property, if set, binds the chipidea usb
controller with a mux for this use.
Signed-off-by: Yossi Mansharoff <yossim@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding over-current-active-high to indicate the over current flag
is high active as typically we use active low for over current
polarity.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
What the code expect is "itc-setting" rather than "gadget-itc-setting",
and this is also correctly described in the optional properties.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
If this property is not set, the max packet size is 1023 bytes, and if
the total of packet size for pervious transactions are more than 256 bytes,
it can't accept any transactions within this frame. The use case is single
transaction, but higher frame rate.
If this property is set, the max packet size is 188 bytes, it can handle
more transactions than above case, it can accept transactions until it
considers the left room size within frame is less than 188 bytes, software
needs to make sure it does not send more than 90%
maximum_periodic_data_per_frame. The use case is multiple transactions, but
less frame rate.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch adds the missing compatible strings from ci_hdrc_imx.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Each vendor may have its specific properties, they are not belonged
to common optional properties, split them from common's.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Improve the description of properties "tx-burst-size-dword"
and "rx-burst-size-dword".
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shanw Guo <shawnguo@kernel.org>
Add an entry for the optional 'phy-clkgate-delay-us' property that is
used to describe the delay time between putting PHY into low power
mode and turning off the PHY clock.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Document the binding for the zynq specific chipidea UDC binding.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
It is used to override the default setting for burst size, changing
burst size takes effect only when the SBUSCFG.AHBBRST = 0.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Combine the ChipIdea USB binding into a single document to reduce
duplication and fragmentation. This marks use of the old PHY bindings as
deprecated. Future compatible bindings should use generic PHY binding.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ivan T. Ivanov <iivanov@mm-sol.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Daniel Tang <dt.tangr@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Philipp Puschmann