* master.kernel.org:/home/rmk/linux-2.6-arm: (28 commits)
ARM: 6411/1: vexpress: set RAM latencies to 1 cycle for PL310 on ct-ca9x4 tile
ARM: 6409/1: davinci: map sram using MT_MEMORY_NONCACHED instead of MT_DEVICE
ARM: 6408/1: omap: Map only available sram memory
ARM: 6407/1: mmu: Setup MT_MEMORY and MT_MEMORY_NONCACHED L1 entries
ARM: pxa: remove pr_<level> uses of KERN_<level>
ARM: pxa168fb: clear enable bit when not active
ARM: pxa: fix cpu_is_pxa*() not expanding to zero when not configured
ARM: pxa168: fix corrected reset vector
ARM: pxa: Use PIO for PI2C communication on Palm27x
ARM: pxa: Fix Vpac270 gpio_power for MMC
ARM: 6401/1: plug a race in the alignment trap handler
ARM: 6406/1: at91sam9g45: fix i2c bus speed
leds: leds-ns2: fix locking
ARM: dove: fix __io() definition to use bus based offset
dmaengine: fix interrupt clearing for mv_xor
ARM: kirkwood: Unbreak PCIe I/O port
ARM: Fix build error when using KCONFIG_CONFIG
ARM: 6383/1: Implement phys_mem_access_prot() to avoid attributes aliasing
ARM: 6400/1: at91: fix arch_gettimeoffset fallout
ARM: 6398/1: add proc info for ARM11MPCore/Cortex-A9 from ARM
...
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Fix rounding-bug in __unmap_single
x86/amd-iommu: Work around S3 BIOS bug
x86/amd-iommu: Set iommu configuration flags in enable-loop
x86, setup: Fix earlyprintk=serial,0x3f8,115200
x86, setup: Fix earlyprintk=serial,ttyS0,115200
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Catch spurious interrupts after disabling counters
tracing/x86: Don't use mcount in kvmclock.c
tracing/x86: Don't use mcount in pvclock.c
It really has no business being there; short of a serious kernel bug
we should already have USER_DS at that point. It shouldn't have been
done on x86 either...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
set ->orig_d0 to -1, same as what sigreturn does
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get rid of a useless wrapper, while we are at it
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PL310 on the ct-ca9x4 tile for the Versatile Express does not need
to add additional latency when accessing its cache RAMs. Unfortunately,
the boot monitor sets this up for an 8-cycle delay on reads and writes,
resulting in greatly reduced memory performance when the L2 cache is
enabled.
This patch sets the L2 RAM latencies to the correct value of 1 cycle
on the ct-ca9x4 tile before enabling the L2 cache.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While debugging bit_spin_lock() hang, it was tracked down to gcc-4.4
misoptimization of non-inlined constant_test_bit() due to non-volatile
addr when 'const volatile unsigned long *addr' cast to 'unsigned long *'
with subsequent unconditional jump to pause (and not to the test) leading
to hang.
Compiling with gcc-4.3 or disabling CONFIG_OPTIMIZE_INLINING yields inlined
constant_test_bit() and correct jump, thus working around the kernel bug.
Other arches than asm-x86 may implement this slightly differently;
2.6.29 mitigates the misoptimization by changing the function prototype
(commit c4295fbb60) but probably fixing the issue
itself is better.
Signed-off-by: Alexander Chumachenko <ledest@gmail.com>
Signed-off-by: Michael Shigorin <mike@osdn.org.ua>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
rdusp() gives us the right value only for the current thread...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We want interrupts disabled on all paths leading to RESTORE_ALL;
otherwise, we are risking an IRQ coming between the updates of
alpha_mv->hae_cache and *alpha_mv->hae_register and set_hae()
within the IRQ getting badly confused.
RESTORE_ALL used to play with disabling IRQ itself, but that got
removed back in 2002, without making sure we had them disabled
on all paths. It's cheaper to make sure we have them disabled than
to revert to original variant...
Remove the detritus left from that commit back in 2002; we used to
need a reload of $0 and $1 since swpipl would change those, but
doing that had become pointless when we stopped doing swpipl in
there...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Davinci SRAM is mapped as MT_DEVICE becasue of the section
mapping pre-requisite instead of intended MT_MEMORY_NONCACHED
Since the section mapping limitation gets fixed with first
patch in this series, the MT_MEMORY_NONCACHED can be used now.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently we map 1 MB section while setting up SRAM on OMAPs
Regardless of the actual memory. The physical OCM RAM available
on OMAP SOCs is in order of KBs. This patch maps only available
sram and cleans up some un-necessary cpu_is_xxx checks.
Mapping un-available or non-accessible(secure) memory on the newer ARM
processor is dangerous. Because ARM CPUs can now speculatively prefetch,
we should avoid mapping any no-existing or secure memory.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch populates the L1 entries for MT_MEMORY and MT_MEMORY_NONCACHED
types so that at boot-up, we can map memories outside system memory
at page level granularity
Previously the mapping was limiting to section level, which creates
unnecessary additional mapping for which physical memory may not
present. On the newer ARM with speculation, this is dangerous and can
result in untraceable aborts.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
x86/hwmon: pkgtemp has no dependency on PCI
MAINTAINERS: Update hwmon entry
x86/hwmon: register alternate sibling upon CPU removal
x86/hwmon: fix initialization of pkgtemp
x86/hwmon: fix initialization of coretemp
x86/hwmon: don't leak device attribute file from pkgtemp_probe() and pkgtemp_remove()
x86/hwmon: avoid deadlock on CPU removal in pkgtemp
x86/hwmon: fix module init for hotplug-but-no-device-found case
hwmon: (lis3) Fix Oops with NULL platform data
When CONFIG_PXA3xx is not selected, cpu_is_pxa3xx() doesn't expand to
zero, which in some places doesn't result in correct optimization.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Reported-and-tested-by: Marek Vasut <marek.vasut@gmail.com>
Reset vector for pxa168 is 0xffff_0000 not 0x0. This fix allows
reboot to work
Signed-off-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This "bpt_code" instruction was killed off in our development line a while
ago (the actual definition of bpt_code that is used is in kernel/traps.c)
but I didn't push it for 2.6.36 because it seemed harmless and I didn't
want to try to push more than absolutely necessary.
However, we recently fixed a bug in our gcc that had been causing
"-gdwarf2" not to be passed to the assembler, and passing this flag causes
an erroneous assembler failure in the presence of code in a data section,
sometimes. While we'd like to track down the bug in the assembler,
we'd also like to make sure 2.6.36 builds with the current toolchain,
so I'm removing this dead code as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
It's a userland pointer; worse, an untrustable one since ptrace
has just provided a chance to modify it.
X-Roothole-Covering-Cabal: TINRCC
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do_signal() should know about saved_mask for it to work...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using cpuid_eax() to determine feature availability on other than
the current CPU is invalid. And feature availability should also be
checked in the hotplug code path.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Looks like a typo from commit d6d834b010.
Signed-off-by: Scott Ellis <scott@jumpnowtek.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove specification of HAVE_ARCH_TRACEHOOK for MN10300 as the arch does not
support it at this time.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SIGRTMAX should be _NSIG not _NSIG-1.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MN10300 arch ext2 bitops assume a big-endian kernel, but the MN10300
arch only runs in little-endian mode.
Reported-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the __unmap_single function the dma_addr is rounded down
to a page boundary before the dma pages are unmapped. The
address is later also used to flush the TLB entries for that
mapping. But without the offset into the dma page the amount
of pages to flush might be miscalculated in the TLB flushing
path. This patch fixes this bug by using the original
address to flush the TLB.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch adds a workaround for an IOMMU BIOS problem to
the AMD IOMMU driver. The result of the bug is that the
IOMMU does not execute commands anymore when the system
comes out of the S3 state resulting in system failure. The
bug in the BIOS is that is does not restore certain hardware
specific registers correctly. This workaround reads out the
contents of these registers at boot time and restores them
on resume from S3. The workaround is limited to the specific
IOMMU chipset where this problem occurs.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch moves the setting of the configuration and
feature flags out out the acpi table parsing path and moves
it into the iommu-enable path. This is needed to reliably
fix resume-from-s3.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
When the policy for user space is to ignore misaligned accesses from user
space, the processor then performs a documented rotation on the accessed
data. This is the result of the access being trapped, and the kernel
disabling the alignment trap before returning to user space again.
In kernel space we always want misaligned accesses to be fixed up. This
is enforced by always re-enabling the alignment trap on every entry into
kernel space from user space. No such re-enabling is performed when an
exception occurs while already in kernel space as the alignment trap is
always supposed to be enabled in that case.
There is however a small race window when a misaligned access in user
space is trapped and the alignment trap disabled, but the CPU didn't
return to user space just yet. Any exception would be entered from kernel
space at that point and the kernel would then execute with the alignment
trap disabled.
Thanks to Maxime Bizon <mbizon@freebox.fr> for providing a test module
that made this issue reproducible.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use a correct udelay value to get bus speed around 100KHz. The udelay
value was most likely copied from the older devices, but the 9g45
is signicantly faster (400MHz, DDR, ..), so a udelay of 2 gives a
bus speed of around 190KHz, which is too fast for some devices.
A udelay value of 5 gives a bus speed of around 90KHz here.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The guest can use the paravirt clock in kvmclock.c which is used
by sched_clock(), which in turn is used by the tracing mechanism
for timestamps, which leads to infinite recursion.
Disable mcount/tracing for kvmclock.o.
Cc: stable@kernel.org
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When using a paravirt clock, pvclock.c can be used by sched_clock(),
which in turn is used by the tracing mechanism for timestamps,
which leads to infinite recursion.
Disable mcount/tracing for pvclock.o.
Cc: stable@kernel.org
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
LKML-Reference: <4C9A9A3F.4040201@goop.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This fixes:
incompatible pointer type: => 89
arch/um/kernel/exec.c: warning: passing argument 2 of 'execve1' from
incompatible pointer type: => 69, 85
arch/um/kernel/exec.c: warning: passing argument 3 of 'execve1' from
incompatible pointer type: => 69, 85
which was introduced by d7627467b7 ("Make do_execve() take a const
filename pointer")
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the regression caused by the commit 6fee48cd33
("dma-mapping: arm: use generic pci_set_dma_mask and
pci_set_consistent_dma_mask").
ARM needs to clip the dma coherent mask for dmabounce devices. This
restores the old trick.
Note that strictly speaking, the DMA API doesn't allow architectures to do
such but I'm not sure it's worth adding the new API to set the dma mask
that allows architectures to clip it.
Reported-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc: Prevent no-handler signal syscall restart recursion.
sparc: Don't mask signal when we can't setup signal frame.
sparc64: Fix race in signal instruction flushing.
sparc64: Support RAW perf events.
Make sigreturn zero regs->trap, make do_signal() do the same on all
paths. As it is, signal interrupting e.g. read() from fd 512 (==
ERESTARTSYS) with another signal getting unblocked when the first
handler finishes will lead to restart one insn earlier than it ought
to. Same for multiple signals with in-kernel handlers interrupting
that sucker at the same time. Same for multiple signals of any kind
interrupting that sucker on 64bit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Explicitly clear the "in-syscall" bit when we have no signal
handler and back up the program counters to back up the system
call.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't invoke the signal handler tracehook in that situation
either.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: update comments to reflect LHCALL_LOAD_GDT_ENTRY.
virtio: console: Prevent userspace from submitting NULL buffers
virtio: console: Fix poll blocking even though there is data to read
earlyprintk can take and I/O port, so we need to handle this case in
the setup code too, otherwise 0x3f8 will be treated as a baud rate.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C7B05A6.4010801@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Torsten reported that there is garbage output,
after commit 8fee13a48e (x86,
setup: enable early console output from the decompressor)
It turns out we missed the offset for that case.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C7B0578.8090807@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch adds CPU type detection for dunnington processor (Family 6
/ Model 29) to be identified as core 2 family cpu type (wikipedia
source).
I tested oprofile on Intel(R) Xeon(R) CPU E7440 reporting itself as
model 29, and it runs without an issue.
Spec:
http://www.intel.com/Assets/en_US/PDF/specupdate/320336.pdf
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Robert Richter <robert.richter@amd.com>
If another cpu does a very wide munmap() on the signal frame area,
it can tear down the page table hierarchy from underneath us.
Borrow an idea from the 64-bit fault path's get_user_insn(), and
disable cross call interrupts during the page table traversal
to lock them in place while we operate.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to have a hypercall which reloaded the entire GDT, then we
switched to one which loaded a single entry (to match the IDT code).
Some comments were not updated, so fix them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reported by: Eviatar Khen <eviatarkhen@gmail.com>
We need to make sure that only the first do_signal() to be handled on
the way out syscall will bother with syscall restarts; additionally, the
check on the "signal has user handler" path had been wrong - compare
with restart prevention in sigreturn()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do_signal() should place the syscall number in gr7, not gr8 when
handling ERESTART_WOULDBLOCK.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use force_sigsegv() rather than force_sig(SIGSEGV, ...) as the former
resets the SEGV handler pointer which will kill the process, rather than
leaving it open to an infinite loop if the SEGV handler itself caused a
SEGV signal.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) sa_handler might be maliciously set to point to kernel memory;
blindly dereferencing it in FDPIC case is a Bad Idea(tm).
b) I'm not sure you need that set_fs(USER_DS) there at all, but if you
do, you'd better do it *before* checking the frame you've decided to
use with access_ok(), lest sigaltstack() becomes a convenient
roothole.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reset restart_block.fn on executing a sigreturn such that any currently
pending system call restarts will be forced to return -EINTR.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The support for the 2 pcie port of the 6282 has broken i/o port by switching
*_IO_PHYS_BASE and *_IO_BUS_BASE. In fact, the patches reintroduced the same
bug solved by commit 35f029e251.
So, I'm adding back *_IO_BUS_BASE in resource declaration and fix definition
of KIRKWOOD_PCIE1_IO_BUS_BASE. With this change, the xgi card on my t5325 is
working again.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: deal with multiple simultaneously pending signals
alpha: fix a 14 years old bug in sigreturn tracing
alpha: unb0rk sigsuspend() and rt_sigsuspend()
alpha: belated ERESTART_RESTARTBLOCK race fix
alpha: Shift perf event pending work earlier in timer interrupt
alpha: wire up fanotify and prlimit64 syscalls
alpha: kill big kernel lock
alpha: fix build breakage in asm/cacheflush.h
alpha: remove unnecessary cast from void* in assignment.
alpha: Use static const char * const where possible
Jonathan Cameron reports that when using the environment
variable KCONFIG_CONFIG, he encounters this error:
make[2]: *** No rule to make target `.config', needed by `arch/arm/boot/compressed/vmlinux.lds'
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARMv7 onwards requires that there are no aliases to the same physical
location using different memory types (i.e. Normal vs Strongly Ordered).
Access to SO mappings when the unaligned accesses are handled in
hardware is also Unpredictable (pgprot_noncached() mappings in user
space).
The /dev/mem driver requires uncached mappings with O_SYNC. The patch
implements the phys_mem_access_prot() function which generates Strongly
Ordered memory attributes if !pfn_valid() (independent of O_SYNC) and
Normal Noncacheable (writecombine) if O_SYNC.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
5cfc8ee0bb (ARM: convert arm to arch_gettimeoffset()) marked all of
at91 AND at91x40 as needing ARCH_USES_GETTIMEOFFSET, and hence no high
res timer support / accurate clock_gettime() - But only at91x40 needs it.
Cc: stable@kernel.org
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unlike the other targets, alpha sets _one_ sigframe and
buggers off until the next syscall/interrupt, even if
more signals are pending. It leads to quite a few unpleasant
inconsistencies, starting with SIGSEGV potentially arriving
not where it should and including e.g. mess with sigsuspend();
consider two pending signals blocked until sigsuspend()
unblocks them. We pick the first one; then, if we are hit
by interrupt while in the handler, we process the second one
as well. If we are not, and if no syscalls had been made,
we get out of the first handler and leave the second signal
pending; normally sigreturn() would've picked it anyway, but
here it starts with restoring the original mask and voila -
the second signal is blocked again. On everything else we
get both delivered consistently.
It's actually easy to fix; the only thing to watch out for
is prevention of double syscall restart. Fortunately, the
idea I've nicked from arm fix by rmk works just fine...
Testcase demonstrating the behaviour in question; on alpha
we get one or both flags set (usually one), on everything
else both are always set.
#include <signal.h>
#include <stdio.h>
int had1, had2;
void f1(int sig) { had1 = 1; }
void f2(int sig) { had2 = 1; }
main()
{
sigset_t set1, set2;
sigemptyset(&set1);
sigemptyset(&set2);
sigaddset(&set2, 1);
sigaddset(&set2, 2);
signal(1, f1);
signal(2, f2);
sigprocmask(SIG_SETMASK, &set2, NULL);
raise(1);
raise(2);
sigsuspend(&set1);
printf("had1:%d had2:%d\n", had1, had2);
}
Tested-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matt Turner <mattst88@gmail.com>
The way sigreturn() is implemented on alpha breaks PTRACE_SYSCALL,
all way back to 1.3.95 when alpha has grown PTRACE_SYSCALL support.
What happens is direct return to ret_from_syscall, in order to bypass
mangling of a3 (error indicator) and prevent other mutilations of
registers (e.g. by syscall restart). That's fine, but... the entire
TIF_SYSCALL_TRACE codepath is kept separate on alpha and post-syscall
stopping/notifying the tracer is after the syscall. And the normal
path we are forcibly switching to doesn't have it.
So we end up with *one* stop in traced sigreturn() vs. two in other
syscalls. And yes, strace is visibly broken by that; try to strace
the following
#include <signal.h>
#include <stdio.h>
void f(int sig) {}
main()
{
signal(SIGHUP, f);
raise(SIGHUP);
write(1, "eeeek\n", 6);
}
and watch the show. The
close(1) = 405
in the end of strace output is coming from return value of write() (6 ==
__NR_close on alpha) and syscall number of exit_group() (__NR_exit_group ==
405 there).
The fix is fairly simple - the only thing we end up missing is the call
of syscall_trace() and we can tell whether we'd been called from the
SYSCALL_TRACE path by checking ra value. Since we are setting the
switch_stack up (that's what sys_sigreturn() does), we have the right
environment for calling syscall_trace() - just before we call
undo_switch_stack() and return. Since undo_switch_stack() will overwrite
s0 anyway, we can use it to store the result of "has it been called from
SYSCALL_TRACE path?" check. The same thing applies in rt_sigreturn().
Tested-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Old code used to set regs->r0 and regs->r19 to force the right
return value. Leaving that after switch to ERESTARTNOHAND
was a Bad Idea(tm), since now that screws the restart - if we
hit the case when get_signal_to_deliver() returns 0, we will
step back to syscall insn, with v0 set to EINTR and a3 to 1.
The latter won't matter, since EINTR is 4, aka __NR_write.
Testcase:
#include <signal.h>
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/syscall.h>
main()
{
sigset_t mask;
sigemptyset(&mask);
sigaddset(&mask, SIGCONT);
sigprocmask(SIG_SETMASK, &mask, NULL);
kill(0, SIGCONT);
syscall(__NR_sigsuspend, 1, "b0rken\n", 7);
}
results on alpha in immediate message to stdout...
Fix is obvious; moreover, since we don't need regs anymore, we can
switch to normal prototypes for these guys and lose the wrappers.
Even better, rt_sigsuspend() is identical to generic version in
kernel/signal.c now.
Tested-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matt Turner <mattst88@gmail.com>
same thing as had been done on other targets back in 2003 -
move setting ->restart_block.fn into {rt_,}sigreturn().
Tested-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Pending work from the performance event subsystem is executed in
the timer interrupt. This patch shifts the call to
perf_event_do_pending() before the call to update_process_times()
as the latter may call back into the perf event subsystem and it
is prudent to have the pending work executed first.
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Matt Turner <mattst88@gmail.com>
The 2.6.36-rc kernel added three new system calls:
fanotify_init, fanotify_mark, and prlimit64. This
patch wires them up on Alpha.
Built and booted on an XP900. Untested beyond that.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Matt Turner <mattst88@gmail.com>
All uses of the BKL on alpha are totally bogus, nothing
is really protected by this. Remove the remaining users
so we don't have to mark alpha as 'depends on BKL'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: linux-alpha@vger.kernel.org
Signed-off-by: Matt Turner <mattst88@gmail.com>
Alpha SMP flush_icache_user_range() is implemented as an inline
function inside include/asm/cacheflush.h. It dereferences @current
but doesn't include linux/sched.h and thus causes build failure if
linux/sched.h wasn't included previously. Fix it by including the
needed header file explicitly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Add IORESOURCE_IRQ_HIGHLEVEL irq flag to dm9000 driver
platform data in board mach-real6410.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix errors reported by checkpatch.pl script
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Avoids build warnings due to the undeclared non-statics.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
If a signal hits us outside of a syscall and another gets delivered
when we are in sigreturn (e.g. because it had been in sa_mask for
the first one and got sent to us while we'd been in the first handler),
we have a chance of returning from the second handler to location one
insn prior to where we ought to return. If r0 happens to contain -513
(-ERESTARTNOINTR), sigreturn will get confused into doing restart
syscall song and dance.
Incredible joy to debug, since it manifests as random, infrequent and
very hard to reproduce double execution of instructions in userland
code...
The fix is simple - mark it "don't bother with restarts" in wrapper,
i.e. set r8 to 0 in sys_sigreturn and sys_rt_sigreturn wrappers,
suppressing the syscall restart handling on return from these guys.
They can't legitimately return a restart-worthy error anyway.
Testcase:
#include <unistd.h>
#include <signal.h>
#include <stdlib.h>
#include <sys/time.h>
#include <errno.h>
void f(int n)
{
__asm__ __volatile__(
"ldr r0, [%0]\n"
"b 1f\n"
"b 2f\n"
"1:b .\n"
"2:\n" : : "r"(&n));
}
void handler1(int sig) { }
void handler2(int sig) { raise(1); }
void handler3(int sig) { exit(0); }
main()
{
struct sigaction s = {.sa_handler = handler2};
struct itimerval t1 = { .it_value = {1} };
struct itimerval t2 = { .it_value = {2} };
signal(1, handler1);
sigemptyset(&s.sa_mask);
sigaddset(&s.sa_mask, 1);
sigaction(SIGALRM, &s, NULL);
signal(SIGVTALRM, handler3);
setitimer(ITIMER_REAL, &t1, NULL);
setitimer(ITIMER_VIRTUAL, &t2, NULL);
f(-513); /* -ERESTARTNOINTR */
write(1, "buggered\n", 9);
return 1;
}
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting of these bits can cause issues on other SMP SoC's not produced
by ARM.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Al Viro reports that calling "sys_sigsuspend(-ERESTARTNOHAND, 0, 0)"
with two signals coming and being handled in kernel space results
in the syscall restart being done twice.
Avoid this by clearing the 'why' flag when we call the signal handling
code to prevent further syscall restarts after the first.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clearing bit 22 in the PL310 Auxiliary Control register (shared
attribute override enable) has the side effect of transforming Normal
Shared Non-cacheable reads into Cacheable no-allocate reads.
Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption.
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the r2p0, r2p1 and r2p2 versions of the Cortex-A9, data corruption
can occur if a shared cache line is replaced on one CPU as another CPU
is accessing it.
This workaround sets two bits in the diagnostic register of the Cortex-A9,
reducing the linefill issuing capabilities of the processor and
avoiding the erroneous behaviour.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On versions of the Cortex-A9 up to and including r2p2, under rare
circumstances, a DMB instruction between 2 write operations may not
ensure the correct visibility ordering of the 2 writes.
This workaround sets a bit in the diagnostic register of the Cortex-A9,
causing the DMB instruction to behave like a DSB, which functions
correctly on the affected cores.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kconfig doesn't have any knowledge of specific v7 cores, so it is possible
to select errata workarounds that may cause inadvertent behaviour when
executed on a core other than those targetted by the fix.
This patch improves the variant and revision checking in proc-v7.S so
that the primary part number is also considered when applying errata
workarounds.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have to use _cansleep gpio accessors in the MMCI driver so as
to avoid slowpath warnings, now U300 has MMCI but doesn't have
these functions in place to siply wrap the existing non-sleeping
functions into sleepable variants.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The prescaler 16 is now used only when the timer runs at 32 MHz
or more. Some comment updates as well.
Acked-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
timer0 to 3 are all on mtu block 0, so don't calculate the clock event
rate based upon mtu block 1's clock speed.
Acked-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hpet: Work around hardware stupidity
x86, build: Disable -fPIE when compiling with CONFIG_CC_STACKPROTECTOR=y
x86, cpufeature: Suppress compiler warning with gcc 3.x
x86, UV: Fix initialization of max_pnode
Lengths and types of breakpoints are encoded in a half byte
into CPU registers. However when we extract these values
and store them, we add a high half byte part to them: 0x40 to the
length and 0x80 to the type.
When that gets reloaded to the CPU registers, the high part
is masked.
While making the instruction breakpoints available for perf,
I zapped that high part on instruction breakpoint encoding
and that broke the arch -> generic translation used by ptrace
instruction breakpoints. Writing dr7 to set an inst breakpoint
was then failing.
There is no apparent reason for these high parts so we could get
rid of them altogether. That's an invasive change though so let's
do that later and for now fix the problem by restoring that inst
breakpoint high part encoding in this sole patch.
Reported-by: Kelvie Wong <kelvie@ieee.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: fix formatting bug in register dumps
arch/tile: fix memcpy_fromio()/memcpy_toio() signatures
arch/tile: Save and restore extra user state for tilegx
arch/tile: Change struct sigcontext to be more useful
arch/tile: finish const-ifying sys_execve()
Linus Torvalds