Here is the big set of char/misc and other driver subsystem patches for
4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
Note, there will be a merge conflict in drivers/misc/lkdtm_core.c when
merging to your tree as one lkdtm patch came in through the perf tree as
well as this one. The resolution is to take the const change that this
tree provides.
All of these have been in linux-next for quite a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWg2Lnw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymTUwCgwp46+I8yPlgDH8oe5TxyyJnpdHQAn1XW0i+a
sBi6WS87In5v1QO1Rgfc
=dH2a
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem patches
for 4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
All of these have been in linux-next for quite a while with no
reported issues"
* tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
VME: Return -EBUSY when DMA list in use
w1: keep balance of mutex locks and refcnts
MAINTAINERS: Update VME subsystem tree.
nvmem: sunxi-sid: add support for A64/H5's SID controller
nvmem: imx-ocotp: Update module description
nvmem: imx-ocotp: Enable i.MX7D OTP write support
nvmem: imx-ocotp: Add i.MX7D timing write clock setup support
nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function
nvmem: imx-ocotp: Add support for banked OTP addressing
nvmem: imx-ocotp: Pass parameters via a struct
nvmem: imx-ocotp: Restrict OTP write to IMX6 processors
nvmem: uniphier: add UniPhier eFuse driver
dt-bindings: nvmem: add description for UniPhier eFuse
nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset
nvmem: qfprom: fix different address space warnings of sparse
nvmem: mtk-efuse: fix different address space warnings of sparse
nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it
nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it
thunderbolt: tb: fix use after free in tb_activate_pcie_devices
MAINTAINERS: Add git tree for Thunderbolt development
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per coresight standards, PIDR2 register has the following format :
[2-0] - JEP106_bits6to4
[3] - JEDEC, designer ID is specified by JEDEC.
However some of the drivers only use mask of 0x3 for the PIDR2 leaving
bits [3-2] unchecked, which could potentially match the component for
a different device altogether. This patch fixes the mask and the
corresponding id bits for the existing devices.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The casting and other things here is odd, and causes sparse to
complain:
drivers/hwtracing/coresight/coresight-stm.c:279:35: warning: incorrect type in argument 1 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:279:35: expected void [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:279:35: got struct stm_drvdata *drvdata
drivers/hwtracing/coresight/coresight-stm.c:327:17: warning: incorrect type in argument 2 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:327:17: expected void volatile [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:327:17: got void *addr
drivers/hwtracing/coresight/coresight-stm.c:330:17: warning: incorrect type in argument 2 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:330:17: expected void volatile [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:330:17: got void *addr
drivers/hwtracing/coresight/coresight-stm.c:333:17: warning: incorrect type in argument 2 (different address spaces)
drivers/hwtracing/coresight/coresight-stm.c:333:17: expected void volatile [noderef] <asn:2>*addr
drivers/hwtracing/coresight/coresight-stm.c:333:17: got void *addr
>From what I can tell, we don't really need to treat ch_addr as
anything besides a pointer, and we can just do pointer math
instead of ORing in the bits of the offset and achieve the same
thing.
Also, we were passing a drvdata pointer to the
coresight_timeout() function, but we really wanted to pass the
address of the register base. Luckily the base is the first
member of the structure, so everything works out, but this is
quite unsafe if we ever change the structure layout. Clean this
all up so sparse stops complaining on this code.
Reported-by: Satyajit Desai <sadesai@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coresight SoC 600 supports ETR save-restore which allows us
to restore a trace session by retaining the RRP/RWP/STS.Full values
when the TMC leaves the Disabled state. However, the TMC doesn't
have a scatter-gather unit in built.
Also, TMCs have different PIDs in different configurations (ETF,
ETB & ETR), unlike the previous generation.
While the DEVID exposes some of the features/changes in the TMC,
it doesn't explicitly advertises the new save-restore feature
as described above.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Coresight SoC 600 TMC ETR supports save-restore feature,
where the values of the RRP/RWP and STS.Full are retained
when it leaves the Disabled state. Hence, we must program the
RRP/RWP and STS.Full to a proper value. For now, set the RRP/RWP
to the base address of the buffer and clear the STS.Full register.
This can be later exploited for proper save-restore of ETR
trace contexts (e.g, perf).
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ETR supports split cache encoding (i.e, separate bits for
read and write transfers) unlike the older version (where read
and write transfers use the same encoding in AXICTL[2-5]).
This feature is not advertised and has to be described by the
static mask associated with the device id.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleans up how we setup the AXICTL register on
TMC ETR. At the moment we don't set the CacheCtrl bits, which
drives the arcache and awcache bits on AXI bus specifying the
cacheablitiy. Set this to Write-back Read and Write-allocate.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TMC in Coresight SoC-600 advertises the AXI address width
in the device configuration register.
Bit 16 - AXIAW_VALID
0 - AXI Address Width not valid
1 - Valid AXI Address width in Bits[23-17]
Bits [23-17] - AXIAW. If AXIAW_VALID = b01 then
0x20 - 32bit AXI address bus
0x28 - 40bit AXI address bus
0x2c - 44bit AXI address bus
0x30 - 48bit AXI address bus
0x34 - 52bit AXI address bus
Use the address bits from the device configuration register, if
available. Otherwise, default to 40bit.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SG unit in the TMC has been removed in Coresight SoC-600.
This is however advertised by DEVID:Bit 24 = 0b1. On the
previous generation, the bit is RES0, hence we can rely on the
DEVID to detect the support.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With new version of TMC ETR, there are differing set of
features supported by the TMC. Add the capability of a
given TMC ETR for making safer decisions at runtime.
The device configuration register of the TMC (DEVID) lists
some of the capabilities. So, we can detect some of them at
probe. However, some of the features (or changes in behavior)
are not advertised and we have to depend on the PID to infer
the features. So we use a static description of the "unadvertised"
capabilities attached to the PID. Combining both, the static
and the dynamic capabilities, we maintain a bitmask of the
available features which can be later checked to take
appropriate actions.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coresight SoC 600 defines a new configuration for TMC, Embedded Trace
Streamer (ETS), indicated by 0x3 in MODE:CONFIG_TYPE. This would break
the existing driver which will treat anything other than ETR/ETB as an
ETF. Fix the driver to check the configuration type properly and also
add a warning if we encounter an unsupported configuration (ETS).
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coresight TMC splits 64bit registers into a pair of 32bit registers
(e.g DBA, RRP, RWP). Provide helpers to read/write to these registers.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new helpers for exposing coresight component registers,
choosing the 64bit variants for appropriate registers.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for reading a lower and upper 32bits of a register
as a single 64bit register. Also add simplified macros for
direct register accesses.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Linux coresight drivers define the programmable ATB replicator as
Qualcomm replicator, while this is designed by ARM. This can cause
confusion to a user selecting the driver. Cleanup all references to
make it explicitly clear. This patch :
1) Replace the compatible string for the replicator :
qcom,coresight-replicator1x => arm,coresight-dynamic-replicator
2) Changes the Kconfig symbol (since this is not part of any defconfigs)
CORESIGHT_QCOM_REPLICATOR => CORESIGHT_DYNAMIC_REPLICATOR
3) Improves the help message in the Kconfig.
4) Changes the name of the driver and the file :
coresight-replicator-qcom => coresight-dynamic-replicator
Cc: Pratik Patel <pratikp@codeaurora.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds handling to program the return stack option into ETMv4 hardware if
specified in the perf command line.
If option is not supported by the hardware then it will be ignored.
This allows capture to move between core/ETM combinations that have the
hardware support to those that do not.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds handling to program the return stack option into PTM hardware if
specified in the perf command line.
If option is not supported by the hardware then it will be ignored.
This allows capture to move between core/ETM combinations that have the
hardware support to those that do not.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return stack is a programmable option on some ETM and PTM hardware.
Adds the option flags to enable this from the perf event command line.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2573 288 296 3157 c55 coresight-etm-perf.o
File size After adding 'const':
text data bss dec hex filename
2613 224 296 3133 c3d coresight-etm-perf.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register ETMSYNCFR holds the number of by that need to be generated before
periodic synchronisation packets are inserted in the trace stream. By
zeroing out the config structure, the current code effectively disable
periodic synchronization.
This patch simply initialise the recommended value for this register as
specified in the technical reference manual.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function etb_disable_hw() is already taking care of unlocking and locking
the coresight access register and as such doesn't need to be placed
within the unlock/lock of function etb_update_buffer().
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a buffer overflow happens the synchronisation patckets usually
present at the beginning of the buffer are lost, a situation that
prevents the decoder from knowing the context of the traces being
decoded.
This patch adds a barrier packet to be used by sink IPs when a buffer
overflow condition is detected. These barrier packets are then used
by the decoding library as markers to force re-synchronisation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Internal CoreSight components are rendering trace data in little-endian
format. As such there is no need to convert the data once more, hence
removing the extra step.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many conditions may cause synchronisation to be lost when updating
the perf ring buffer but the end result is still the same: synchronisation
is lost. As such there is no need to increment the lost count for each
condition, just once will suffice.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates, and
a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only reported
issue being a merge problem with this tree and the jc-docs tree in the
w1 documentation area. The fix should be obvious for what to do when it
happens, if not, we can send a follow-up patch for it afterward.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpXKA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynLrQCdG9SxRjAbOd6pT9Fr2NAzpUG84YsAoLw+I3iO
EMi60UXWqAFJbtVMS9Aj
=yrSq
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the "big" char/misc driver patchset for 4.13-rc1.
Lots of stuff in here, a large thunderbolt update, w1 driver header
reorg, the new mux driver subsystem, google firmware driver updates,
and a raft of other smaller things. Full details in the shortlog.
All of these have been in linux-next for a while with the only
reported issue being a merge problem with this tree and the jc-docs
tree in the w1 documentation area"
* tag 'char-misc-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (147 commits)
misc: apds990x: Use sysfs_match_string() helper
mei: drop unreachable code in mei_start
mei: validate the message header only in first fragment.
DocBook: w1: Update W1 file locations and names in DocBook
mux: adg792a: always require I2C support
nvmem: rockchip-efuse: add support for rk322x-efuse
nvmem: core: add locking to nvmem_find_cell
nvmem: core: Call put_device() in nvmem_unregister()
nvmem: core: fix leaks on registration errors
nvmem: correct Broadcom OTP controller driver writes
w1: Add subsystem kernel public interface
drivers/fsi: Add module license to core driver
drivers/fsi: Use asynchronous slave mode
drivers/fsi: Add hub master support
drivers/fsi: Add SCOM FSI client device driver
drivers/fsi/gpio: Add tracepoints for GPIO master
drivers/fsi: Add GPIO based FSI master
drivers/fsi: Document FSI master sysfs files in ABI
drivers/fsi: Add error handling for slave
drivers/fsi: Add tracepoints for low-level operations
...
Coresight includes debug module and usually the module connects with CPU
debug logic. ARMv8 architecture reference manual (ARM DDI 0487A.k) has
description for related info in "Part H: External Debug".
Chapter H7 "The Sample-based Profiling Extension" introduces several
sampling registers, e.g. we can check program counter value with
combined CPU exception level, secure state, etc. So this is helpful for
analysis CPU lockup scenarios, e.g. if one CPU has run into infinite
loop with IRQ disabled. In this case the CPU cannot switch context and
handle any interrupt (including IPIs), as the result it cannot handle
SMP call for stack dump.
This patch is to enable coresight debug module, so firstly this driver
is to bind apb clock for debug module and this is to ensure the debug
module can be accessed from program or external debugger. And the driver
uses sample-based registers for debug purpose, e.g. when system triggers
panic, the driver will dump program counter and combined context
registers (EDCIDSR, EDVIDSR); by parsing context registers so can
quickly get to know CPU secure state, exception level, etc.
Some of the debug module registers are located in CPU power domain, so
this requires the CPU power domain stays on when access related debug
registers, but the power management for CPU power domain is quite
dependent on SoC integration for power management. For the platforms
which with sane power controller implementations, this driver follows
the method to set EDPRCR to try to pull the CPU out of low power state
and then set 'no power down request' bit so the CPU has no chance to
lose power.
If the SoC has not followed up this design well for power management
controller, the user should use the command line parameter or sysfs
to constrain all or partial idle states to ensure the CPU power
domain is enabled and access coresight CPU debug component safely.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is refactor to add function of_coresight_get_cpu(), so it's used to
retrieve CPU id for coresight component. Finally can use it as a common
function for multiple places.
Suggested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The of_get_coresight_platform_data iterates over the possible CPU nodes
to find a given cpu phandle. However it does not drop the reference
to the node pointer returned by the of_get_coresight_platform_data.
This patch also introduces another minor fix is to use
of_cpu_device_node_get() to replace of_get_cpu_node().
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[Leo: minor tweaks for of_get_coresight_platform_data]
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before making any DMA API calls, the ETR driver should really be setting
its masks to ensure that DMA is possible. Especially since it can
address more than the 32-bit default mask set by the AMBA bus code.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete a character in this description for a condition check.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Link: http://events.linuxfoundation.org/sites/events/files/slides/LCJ16-Refactor_Strings-WSang_0.pdf
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Almost low level functions from open firmware have used const to
qualify device_node structures, so add const for device_node
parameters in of_coresight related functions.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current code the output logs are not well symmetric for sink and link
enabling and disabling. This patch is to fix that so can output paired
logs.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For software sources (i.e STM), there could be multiple agents
generating the trace data, unlike the ETMs. So we need to
properly do the accounting for the active number of users
to disable the device when the last user goes away. Right
now, the reference counting is broken for sources as we skip
the actions when we detect that the source is enabled.
This patch fixes the problem by adding the refcounting for
software sources, even when they are enabled.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a coresight tracing session, the components along the path
from the source to sink are disabled after the source is disabled.
However, if the source was not actually disabled due to active
users, we should not disable the components in the path.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
etm_probe4() holds get_online_cpus() while invoking
cpuhp_setup_state_nocalls().
cpuhp_setup_state_nocalls() invokes get_online_cpus() as well. This is
correct, but prevents the conversion of the hotplug locking to a percpu
rwsem.
Use cpuhp_setup_state_nocalls_cpuslocked() to avoid the nested
call. Convert *_online_cpus() to the new interfaces while at it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20170524081547.983493849@linutronix.de
Linus Torvalds