In order to realize the keep-alive mechanism in mac80211 stack, reporting
accurate tx ack status for nullfunc frame is added in this commit.
If current frame is nullfunc frame, we ask firmware to report by filling
TX report bit in TX descriptor. After this frame DMA done, TX interrupt is
triggered but TX status is unknown at this moment, so enqueue this skb
into tx_report->queue. Finally, C2H report will be received if the frame
is transmitted successfully or retried over, and then we report to mac80211
with IEEE80211_TX_STAT_ACK flag only if it's successful. Otherwise, if
failure or timeout (one second), we report to mac80211 without this flag.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We can have pm_runtime_get_sync() return 1, and we can have
pm_runtime_put_sync() return -EBUSY. See rpm_suspend() and
rpm_resume() for more information.
Fix the issue by returning 0 from wl12xx_sdio_power_on() on success.
And use pm_runtime_put() instead of pm_runtime_put_sync() for
wl12xx_sdio_power_off(), then the MMC subsystem will idle the bus
when suitable.
Otherwise wlcore can sometimes get confused and may report bogus
errors and WLAN connection can fail.
Note that while wlcore checks the return value for wl1271_power_on(),
the return value is ignored for wl1271_power_off(). Let's fix them
both though to avoid further confusion in the future.
Fixes: 60f36637bb ("wlcore: sdio: allow pm to handle sdio power")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Salil Mehta says:
====================
Misc. bug fixes & some minor additions to HNS3 driver
This patch-set provides some bug fixes figured out during testing
and review. It also provides some additions due to running of the
existing code on the new revision of the HNS3 hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When register a RoCE client with hnae3vf device, it needs to judge
the device whether support RoCE vf function. Otherwise, it will
lead to calltrace when RoCE is not support vf function and remove
roce device.
The calltrace as follows:
[ 93.156614] Unable to handle kernel NULL pointer dereference at virtual address 00000015
<SNIP>
[ 93.278784] Call trace:
[ 93.278788] hnae3_match_n_instantiate+0x24/0xd8 [hnae3]
[ 93.278790] hnae3_register_client+0xcc/0x150 [hnae3]
[ 93.278801] hns_roce_hw_v2_init+0x18/0x1000 [hns_roce_hw_v2]
[ 93.278805] do_one_initcall+0x58/0x160
[ 93.278807] do_init_module+0x64/0x1d8
[ 93.278809] load_module+0x135c/0x15c8
[ 93.278811] SyS_finit_module+0x100/0x118
[ 93.278816] __sys_trace_return+0x0/0x4
[ 93.278827] Code: aa0003f5 12001c56 aa1e03e0 d503201f (b9402660)
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Reported-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reported-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware now supports control of all leds. Existing HNS3 driver code
only supported led locate command over SFP Fibre ports. But now it
is also supported over copper port.
This patch removes existing not needed code for the led locate
command and updates the led control command between driver and
firmware.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous implementation of led control for fibre port , parses the
port speed configuration, checks the link status and traffic status per
second, and updates the blink status of link led, traffic led and speed
led.
Now, the firmware takes responsibility to handle the led, the dirver just
needs to deal with locate command.
So the codes for link led, traffic led and speed led are useless now. This
patch removes these redundant codes.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we down the port, some packets are left in TX/RX buffer. When we
up the port again, these old packets are forwarded to protocol stack
or are sent to internet. It will make some problem. TX/RX buffer should
be cleared when stopping port. This patch adds some function to ensure
the buffer is clean when port is started. We should clear the rings
when clients are being un-initialized as well.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our code will ensure that hns3_clear_tx_ring is not used to cleared
RX rings and hns3_clear_rx_ring is not used to cleared TX rings. So
the ring type check is unnecessary.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX Buffer Descriptor contains a VALID bit which indicates if the BD
is valid and has some data. This field is set by HNS3 hardware to
intimate the driver of some valid data present in the BD. nd should
be reset by the driver when BD is being used again. In the existing
code this bit was not being (re-)initialized properly and hence was
causing problems.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNAE3 module supports kernel nic driver, user nic driver and roce driver,
and there are 3 client types. Driver uses one bit(HNAE3_CLIENT_INITED_B)
to indicate the client initialization state, it will cause confusion
for 3 client types. This patch fixes it by use 3 bits to indicate the
initialization state.
Fixes: 38caee9d3e ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the firmware updates the crq's tail pointer, if the PF driver
reads the data in the crq, the data may be incomplete at this time,
which will lead to the driver read an unknown message.
This patch fixes it by checking if crq is not empty before reading the
message.
Fixes: c1a81619d7 ("net: hns3: Add mailbox interrupt handling to PF driver")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HCLGE_PROMISC_TX_EN_B and HCLGE_PROMISC_RX_EN_B are not supported
on pdev revision(0x20), new revision(0x21) supports them.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware Revision(0x21) Buffer Descriptor adds a field STRP_TAGP
for vlan stripped processed indication. STRP_TAGP field has 2 bits,
bit 0 is stripped indication of the vlan tag in outer vlan tag
field, bit 1 is stripped indication of the vlan tag in inner vlan
tag field. For each bit, 0 indicates the tag is not stripped and
1 indicates the tag is stripped.
This patch adds STRP_TAGP support for revision(0x21), and does not
change the revision(0x20) action.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 Hardware can support up to two VLAN tags in transmit leg, the PPP
module can handle the packets based on the tag1 and tag2 config. This
patch adds support for tag2 config for vlan handling
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the latest revision of the hardware, if a packet is spanning
across multiple BDs then only VLD bit and current data size info
is valid in each BD, and rest of the information is only valid
in the last BD of the packet. In such case we should make sure
we are fetching RX packet size from the first descriptor and
information like VLAN should be fetched from last BD.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct Qdisc has a lot of holes, especially after commit
a53851e2c3 ("net: sched: explicit locking in gso_cpu fallback"),
which as a side effect, moved the fields just after 'busylock'
on a new cacheline.
Since both 'padded' and 'refcnt' are not updated frequently, and
there is a hole before 'gso_skb', we can move such fields there,
saving a cacheline without any performance side effect.
Before this commit:
pahole -C Qdisc net/sche/sch_generic.o
# ...
/* size: 384, cachelines: 6, members: 25 */
/* sum members: 236, holes: 3, sum holes: 92 */
/* padding: 56 */
After this commit:
pahole -C Qdisc net/sche/sch_generic.o
# ...
/* size: 320, cachelines: 5, members: 25 */
/* sum members: 236, holes: 2, sum holes: 28 */
/* padding: 56 */
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIMCOM are reusing a single device ID for many (all of their?)
different modems, based on different chipsets and firmwares. Newer
Qualcomm chipset generations require setting DTR to wake the QMI
function. The SIM7600E modem is using such a chipset, making it
fail to work with this driver despite the device ID match.
Fix by unconditionally enabling the SET_DTR quirk for all SIMCOM
modems using this specific device ID. This is similar to what
we already have done for another case of device IDs recycled over
multiple chipset generations: 14cf4a771b ("drivers: net: usb:
qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201")
Initial testing on an older SIM7100 modem shows no immediate side
effects.
Reported-by: Sebastian Sjoholm <sebastian.sjoholm@gmail.com>
Cc: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netsec network controller IP can drive 64 address bits for DMA, and
the DMA mask is set accordingly in the driver. However, the SynQuacer
SoC, which is the only silicon incorporating this IP at the moment,
integrates this IP in a manner that leaves address bits [63:40]
unconnected.
Up until now, this has not resulted in any problems, given that the DDR
controller doesn't decode those bits to begin with. However, recent
firmware updates for platforms incorporating this SoC allow the IOMMU
to be enabled, which does decode address bits [47:40], and allocates
top down from the IOVA space, producing DMA addresses that have bits
set that have been left unconnected.
Both the DT and ACPI (IORT) descriptions of the platform take this into
account, and only describe a DMA address space of 40 bits (using either
dma-ranges DT properties, or DMA address limits in IORT named component
nodes). However, even though our IOMMU and bus layers may take such
limitations into account by setting a narrower DMA mask when creating
the platform device, the netsec probe() entrypoint follows the common
practice of setting the DMA mask uncondionally, according to the
capabilities of the IP block itself rather than to its integration into
the chip.
It is currently unclear what the correct fix is here. We could hack around
it by only setting the DMA mask if it deviates from its default value of
DMA_BIT_MASK(32). However, this makes it impossible for the bus layer to
use DMA_BIT_MASK(32) as the bus limit, and so it appears that a more
comprehensive approach is required to take DMA limits imposed by the
SoC as a whole into account.
In the mean time, let's limit the DMA mask to 40 bits. Given that there
is currently only one SoC that incorporates this IP, this is a reasonable
approach that can be backported to -stable and buys us some time to come
up with a proper fix going forward.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Masahisa Kojima <masahisa.kojima@linaro.org>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe Roullier says:
====================
net: ethernet: stmmac: add support for stm32mp1
Patches to have Ethernet support on stm32mp1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch describes syscon DT bindings.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manage dwmac-4.20a version from synopsys
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add description for Ethernet MPU families fields
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Glue codes to support stm32mp157c device and stay
compatible with stm32 mcu familly
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add a documentation for ptp_qoriq dt-bindings.
The description for ptp_qoriq dt-bindings was actually moved
from Documentation/devicetree/bindings/net/fsl-tsec-phy.txt,
since gianfar_ptp driver was moved to ptp_qoriq driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Global variable gfar_phc_index was used to get and store
phc index through gianfar_ptp driver. However gianfar_ptp
had been renamed as ptp_qoriq for QorIQ common PTP driver.
This gfar_phc_index doesn't work any more, and the phc index
is stored in drvdata now. This patch is to support getting
phc index through ptp_qoriq drvdata.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move some definitions in ptp_qoriq.c
to the header file.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gianfar_ptp was the PTP clock driver for 1588 timer
module of Freescale QorIQ eTSEC (Enhanced Three-Speed
Ethernet Controllers) platforms. Actually QorIQ DPAA
(Data Path Acceleration Architecture) platforms is
also using the same 1588 timer module in hardware.
This patch is to rework gianfar_ptp as QorIQ common
PTP driver to support both DPAA and eTSEC. Moved
gianfar_ptp.c to drivers/ptp/, renamed it as
ptp_qoriq.c, and renamed many variables. There were
not any function changes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixup the checksum for CHECKSUM_COMPLETE when pulling skbs on RX path.
Otherwise we get splats when tc mirred is used to redirect packets to ifb.
Before fix:
nic: hw csum failure
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sridhar Samudrala says:
====================
Enable virtio_net to act as a standby for a passthru device
The main motivation for this patch is to enable cloud service providers
to provide an accelerated datapath to virtio-net enabled VMs in a
transparent manner with no/minimal guest userspace changes. This also
enables hypervisor controlled live migration to be supported with VMs that
have direct attached SR-IOV VF devices.
Patch 1 introduces a failover module that provides a generic interface for
paravirtual drivers to listen for netdev register/unregister/link change
events from pci ethernet devices with the same MAC and takeover their
datapath. The notifier and event handling code is based on the existing
netvsc implementation.
Patch 2 refactors netvsc to use the registration/notification framework
introduced by failover module.
Patch 3 introduces a net_failover driver that provides an automated
failover mechanism to paravirtual drivers via APIs to create and destroy
a failover master netdev and mananges a primary and standby slave netdevs
that get registered via the generic failover infrastructure.
Patch 4 introduces a new feature bit VIRTIO_NET_F_STANDBY to virtio-net
that can be used by hypervisor to indicate that virtio_net interface
should act as a standby for another device with the same MAC address.
Patch 5 extends virtio_net to use alternate datapath when available and
registered. When STANDBY feature is enabled, virtio_net driver uese the
net_failover API to create an additional 'failover' netdev that acts as
a master device and controls 2 slave devices. The original virtio_net
netdev is registered as 'standby' netdev and a passthru/vf device with
the same MAC gets registered as 'primary' netdev. Both 'standby' and
'failover' netdevs are associated with the same 'pci' device. The user
accesses the network interface via 'failover' netdev. The 'failover'
netdev chooses 'primary' netdev as default for transmits when it is
available with link up and running.
As this patch series is initially focusing on usecases where hypervisor
fully controls the VM networking and the guest is not expected to directly
configure any hardware settings, it doesn't expose all the ndo/ethtool ops
that are supported by virtio_net at this time. To support additional usecases,
it should be possible to enable additional ops later by caching the state
in failover netdev and replaying when the 'primary' netdev gets registered.
At the time of live migration, the hypervisor needs to unplug the VF device
from the guest on the source host and reset the MAC filter of the VF to
initiate failover of datapath to virtio before starting the migration. After
the migration is completed, the destination hypervisor sets the MAC filter
on the VF and plugs it back to the guest to switch over to VF datapath.
This patch is based on the discussion initiated by Jesse on this thread.
https://marc.info/?l=linux-virtualization&m=151189725224231&w=2
v12:
- Tested live migration with virtio-net/AVF(i40evf) configured in failover
mode while running iperf in background. Tried static ip and dhcp
configurations using 'network' scripts and Network Manager.
- Build tested netvsc module.
Updates:
- Extended generic failover module to do common functions like setting
FAILOVER_SLAVE flag, registering rx-handler and linking to upper dev in
the generic register/unregister handlers.
This required adding 3 additional failover ops pre_register, pre_unregister
and handle_frame. netvsc and net_failover drivers are updated to support
these ops.
v11:
- Split net_failover module into 2 components.
1. 'failover' module that provides generic failover infrastructure
to register a failover instance and listen for slave events.
2. 'net_failover' driver that provides APIs to create/destroy upper
netdev and supports 3-netdev model used by virtio-net.
- Added documentation
v10:
- fix net_failover_open() to update failover CARRIER correctly based on
standby and primary states.
- fix net_failover_handle_frame() to handle frames received on standby
when primary is present.
- replace netdev_upper_dev_link with netdev_master_upper_dev_link and
handle lower dev state changes.
- fix net_failver_create() and net_failover_register() interfaces to
use ERR_PTR and avoid arg **
- disable setting mac address when virtio-net in STANDBY mode
- document exported symbols
- added entry to MAINTAINERS file
v9:
Select NET_FAILOVER automatically when VIRTIO_NET/HYPERV_NET
are enabled. (stephen)
v8:
- Made the failover managment routines more robust by updating the feature
bits/other fields in the failover netdev when slave netdevs are
registered/unregistered. (mst)
- added support for handling vlans.
- Limited the changes in netvsc to only use the notifier/event/lookups
from the failover module. The slave register/unregister/link-change
handlers are only updated to use the getbymac routine to get the
upper netdev. There is no change in their functionality. (stephen)
- renamed structs/function/file names to use net_failover prefix. (mst)
v7
- Rename 'bypass/active/backup' terminology with 'failover/primary/standy'
(jiri, mst)
- re-arranged dev_open() and dev_set_mtu() calls in the register routines
so that they don't get called for 2-netdev model. (stephen)
- fixed select_queue() routine to do queue selection based on VF if it is
registered as primary. (stephen)
- minor bugfixes
v6 RFC:
Simplified virtio_net changes by moving all the ndo_ops of the
bypass_netdev and create/destroy of bypass_netdev to 'bypass' module.
avoided 2 phase registration(driver + instances).
introduced IFF_BYPASS/IFF_BYPASS_SLAVE dev->priv_flags
replaced mutex with a spinlock
v5 RFC:
Based on Jiri's comments, moved the common functionality to a 'bypass'
module so that the same notifier and event handlers to handle child
register/unregister/link change events can be shared between virtio_net
and netvsc.
Improved error handling based on Siwei's comments.
v4:
- Based on the review comments on the v3 version of the RFC patch and
Jakub's suggestion for the naming issue with 3 netdev solution,
proposed 3 netdev in-driver bonding solution for virtio-net.
v3 RFC:
- Introduced 3 netdev model and pointed out a couple of issues with
that model and proposed 2 netdev model to avoid these issues.
- Removed broadcast/multicast optimization and only use virtio as
backup path when VF is unplugged.
v2 RFC:
- Changed VIRTIO_NET_F_MASTER to VIRTIO_NET_F_BACKUP (mst)
- made a small change to the virtio-net xmit path to only use VF datapath
for unicasts. Broadcasts/multicasts use virtio datapath. This avoids
east-west broadcasts to go over the PCI link.
- added suppport for the feature bit in qemu
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables virtio_net to switch over to a VF datapath when STANDBY
feature is enabled and a VF netdev is present with the same MAC address.
It allows live migration of a VM with a direct attached VF without the need
to setup a bond/team between a VF and virtio net device in the guest.
It uses the API that is exported by the net_failover driver to create and
and destroy a master failover netdev. When STANDBY feature is enabled, an
additional netdev(failover netdev) is created that acts as a master device
and tracks the state of the 2 lower netdevs. The original virtio_net netdev
is marked as 'standby' netdev and a passthru device with the same MAC is
registered as 'primary' netdev.
The hypervisor needs to unplug the VF device from the guest on the source
host and reset the MAC filter of the VF to initiate failover of datapath
to virtio before starting the migration. After the migration is completed,
the destination hypervisor sets the MAC filter on the VF and plugs it back
to the guest to switch over to VF datapath.
This patch is based on the discussion initiated by Jesse on this thread.
https://marc.info/?l=linux-virtualization&m=151189725224231&w=2
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature bit can be used by hypervisor to indicate virtio_net device to
act as a standby for another device with the same MAC address.
VIRTIO_NET_F_STANDBY is defined as bit 62 as it is a device feature bit.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net_failover driver provides an automated failover mechanism via APIs
to create and destroy a failover master netdev and manages a primary and
standby slave netdevs that get registered via the generic failover
infrastructure.
The failover netdev acts a master device and controls 2 slave devices. The
original paravirtual interface gets registered as 'standby' slave netdev and
a passthru/vf device with the same MAC gets registered as 'primary' slave
netdev. Both 'standby' and 'failover' netdevs are associated with the same
'pci' device. The user accesses the network interface via 'failover' netdev.
The 'failover' netdev chooses 'primary' netdev as default for transmits when
it is available with link up and running.
This can be used by paravirtual drivers to enable an alternate low latency
datapath. It also enables hypervisor controlled live migration of a VM with
direct attached VF by failing over to the paravirtual datapath when the VF
is unplugged.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the registration/notification framework supported by the generic
failover infrastructure.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failover module provides a generic interface for paravirtual drivers
to register a netdev and a set of ops with a failover instance. The ops
are used as event handlers that get called to handle netdev register/
unregister/link change/name change events on slave pci ethernet devices
with the same mac address as the failover netdev.
This enables paravirtual drivers to use a VF as an accelerated low latency
datapath. It also allows migration of VMs with direct attached VFs by
failing over to the paravirtual datapath when the VF is unplugged.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP sockets originated in a VRF can improve their performance if CRC32c
computation is delegated to underlying devices: update device features,
setting NETIF_F_SCTP_CRC. Iterating the following command in the topology
proposed with [1],
# ip vrf exec vrf-h2 netperf -H 192.0.2.1 -t SCTP_STREAM -- -m 10K
the measured throughput in Mbit/s improved from 2395 ± 1% to 2720 ± 1%.
[1] https://www.spinics.net/lists/netdev/msg486007.html
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers, such as DWC EQOS on Tegra, need to perform operations that
can sleep under this lock (clk_set_rate() in tegra_eqos_fix_speed()) for
proper operation. Since there is no need for this lock to be a spinlock,
convert it to a mutex instead.
Fixes: e6ea2d16fc ("net: stmmac: dwc-qos: Add Tegra186 support")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx-timeout mostly happens due to some issue in the device. In such cases,
debug dump would be helpful for identifying the cause of the issue.
This patch adds support to spill debug data during the Tx timeout. Here
bnx2x_panic_dump() API is used instead of bnx2x_panic(), since we still
want to allow the Tx-timeout recovery a chance to succeed.
Changes from previous version:
-------------------------------
v2: Fixed a coding error.
Please consider applying this to "net-next".
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) Null pointer dereference when dumping conntrack helper configuration,
from Taehee Yoo.
2) Missing sanitization in ebtables extension name through compat,
from Paolo Abeni.
3) Broken fetch of tracing value, from Taehee Yoo.
4) Incorrect arithmetics in packet ratelimiting.
5) Buffer overflow in IPVS sync daemon, from Julian Anastasov.
6) Wrong argument to nla_strlcpy() in nfnetlink_{acct,cthelper},
from Eric Dumazet.
7) Fix splat in nft_update_chain_stats().
8) Null pointer dereference from object netlink dump path, from
Taehee Yoo.
9) Missing static_branch_inc() when enabling counters in existing
chain, from Taehee Yoo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since an SRP remote port is attached as a child to shost->shost_gendev
and as the only child, the translation from the shost pointer into an
rport pointer must happen by looking up the shost child that is an
rport. This patch fixes the following KASAN complaint:
BUG: KASAN: slab-out-of-bounds in srp_timed_out+0x57/0x110 [scsi_transport_srp]
Read of size 4 at addr ffff880035d3fcc0 by task kworker/1:0H/19
CPU: 1 PID: 19 Comm: kworker/1:0H Not tainted 4.16.0-rc3-dbg+ #1
Workqueue: kblockd blk_mq_timeout_work
Call Trace:
dump_stack+0x85/0xc7
print_address_description+0x65/0x270
kasan_report+0x231/0x350
srp_timed_out+0x57/0x110 [scsi_transport_srp]
scsi_times_out+0xc7/0x3f0 [scsi_mod]
blk_mq_terminate_expired+0xc2/0x140
bt_iter+0xbc/0xd0
blk_mq_queue_tag_busy_iter+0x1c7/0x350
blk_mq_timeout_work+0x325/0x3f0
process_one_work+0x441/0xa50
worker_thread+0x76/0x6c0
kthread+0x1b2/0x1d0
ret_from_fork+0x24/0x30
Fixes: e68ca75200 ("scsi_transport_srp: Reduce failover time")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
->commit() cannot fail at the moment.
Followup-patch adds kmalloc calls in the commit phase, so we'll need
to be able to handle errors.
Make it so that -EGAIN causes a full replay, and make other errors
cause the transaction to fail.
Failing is ok from a consistency point of view as long as we
perform all actions that could return an error before
we increment the generation counter and the base seq.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Similar to previous patch, this time, merge redirect+nat.
The redirect module is just 2k in size, get rid of it and make
redirect part available from the nat core.
before:
text data bss dec hex filename
19461 1484 4138 25083 61fb net/netfilter/nf_nat.ko
1236 792 0 2028 7ec net/netfilter/nf_nat_redirect.ko
after:
20340 1508 4138 25986 6582 net/netfilter/nf_nat.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of using extra modules for these, turn the config options into
an implicit dependency that adds masq feature to the protocol specific nf_nat module.
before:
text data bss dec hex filename
2001 860 4 2865 b31 net/ipv4/netfilter/nf_nat_masquerade_ipv4.ko
5579 780 2 6361 18d9 net/ipv4/netfilter/nf_nat_ipv4.ko
2860 836 8 3704 e78 net/ipv6/netfilter/nf_nat_masquerade_ipv6.ko
6648 780 2 7430 1d06 net/ipv6/netfilter/nf_nat_ipv6.ko
after:
text data bss dec hex filename
7245 872 8 8125 1fbd net/ipv4/netfilter/nf_nat_ipv4.ko
9165 848 12 10025 2729 net/ipv6/netfilter/nf_nat_ipv6.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
These have to be included always when nf_socket.h is included.
Signed-off-by: Máté Eckl <ecklm94@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch fixes the following splat.
[118709.054937] BUG: using smp_processor_id() in preemptible [00000000] code: test/1571
[118709.054970] caller is nft_update_chain_stats.isra.4+0x53/0x97 [nf_tables]
[118709.054980] CPU: 2 PID: 1571 Comm: test Not tainted 4.17.0-rc6+ #335
[...]
[118709.054992] Call Trace:
[118709.055011] dump_stack+0x5f/0x86
[118709.055026] check_preemption_disabled+0xd4/0xe4
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The snapshot trigger currently only affects the main ring buffer, even when
it is used by the instances. This can be confusing as the snapshot trigger
is listed in the instance.
> # cd /sys/kernel/tracing
> # mkdir instances/foo
> # echo snapshot > instances/foo/events/syscalls/sys_enter_fchownat/trigger
> # echo top buffer > trace_marker
> # echo foo buffer > instances/foo/trace_marker
> # touch /tmp/bar
> # chown rostedt /tmp/bar
> # cat instances/foo/snapshot
# tracer: nop
#
#
# * Snapshot is freed *
#
# Snapshot commands:
# echo 0 > snapshot : Clears and frees snapshot buffer
# echo 1 > snapshot : Allocates snapshot buffer, if not already allocated.
# Takes a snapshot of the main buffer.
# echo 2 > snapshot : Clears snapshot buffer (but does not allocate or free)
# (Doesn't have to be '2' works with any number that
# is not a '0' or '1')
> # cat snapshot
# tracer: nop
#
# _-----=> irqs-off
# / _----=> need-resched
# | / _---=> hardirq/softirq
# || / _--=> preempt-depth
# ||| / delay
# TASK-PID CPU# |||| TIMESTAMP FUNCTION
# | | | |||| | |
bash-1189 [000] .... 111.488323: tracing_mark_write: top buffer
Not only did the snapshot occur in the top level buffer, but the instance
snapshot buffer should have been allocated, and it is still free.
Cc: stable@vger.kernel.org
Fixes: 85f2b08268 ("tracing: Add basic event trigger framework")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Several subsystems depend on INFINIBAND_ADDR_TRANS, which in turn depends
on INFINIBAND. However, when with CONFIG_INIFIBAND=m, this leads to a
link error when another driver using it is built-in. The
INFINIBAND_ADDR_TRANS dependency is insufficient here as this is
a 'bool' symbol that does not force anything to be a module in turn.
fs/cifs/smbdirect.o: In function `smbd_disconnect_rdma_work':
smbdirect.c:(.text+0x1e4): undefined reference to `rdma_disconnect'
net/9p/trans_rdma.o: In function `rdma_request':
trans_rdma.c:(.text+0x7bc): undefined reference to `rdma_disconnect'
net/9p/trans_rdma.o: In function `rdma_destroy_trans':
trans_rdma.c:(.text+0x830): undefined reference to `ib_destroy_qp'
trans_rdma.c:(.text+0x858): undefined reference to `ib_dealloc_pd'
Fixes: 9533b292a7 ("IB: remove redundant INFINIBAND kconfig dependencies")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Tzu-En Huang