Implement burst parameter sequence for 8723bu parts. Eventually this
should be moved into device specific sections.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The vendor driver does not set FPGA0_TX_INFO here. In additiona the
8723bu can handler a larger PBP page size.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reorganize the init sequence in order to be able to compare to the
8723bu vendor driver's init sequence.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In addition make register read/write flow match closer to vendor
driver flow. This is mainly to be able to compare the register write
log with the vendor driver, and can be optimized later once 8723bu
support is working.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No indication of what register 0xa3 does anywhere in the vendor source.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is going to need to be split up into chip specific
variants.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Retrieve the XTAL_K value in the parse_efuse() functions as it's
location various on a per device basis. For parts that do not provide
an XTAL_K value, skip setting it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Additional tweaks to further map the init sequence for the 8723bu to
that of the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This matches the order of the 8723bu vendor driver
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This implements the 8723bu specific power on sequence as it is
different from that of the 8723au chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8723bu does not like REG_AFE_XTAL_CTRL being set, so skip this for
now, to match the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Issue a BT_INFO command to verify the status of BT/WiFi settings.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8723bu BT registers are written via the mailbox interface. Add support
for writing these and corresponding C2H event responses.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 64 bit mailbox commands also provide a different method for
mailbox command responses (C2H events).
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This adds code to parse the new RX descriptor format used by the
8723bu/8192eu parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The nextgen chips use a slightly different RX descriptor format. This
adds support for the new format.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the correct type when setting PS TDMA for 8723bu. This matches the
vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8723bu is a WiFi/BT combo part. When initializing it for WiFi,
make sure to tell it not to ignore WiFi activity.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement additional init sequence code for the 8723bu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove an unused variable to make the compiler happy.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This should initialize the antennas on the 8723bu, but so far I am
still not receiving anything :( More work is needed.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a first stab of implementing rtl8723bu_config_channel(). For
now this will only do 20MHz channels.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX power values are laid out differently in EFUSE found in RTL8192EU &
RTL8188EU devices. TX power indices and differences for each RF path
are not interleaved (A, B, A, B), as in other chips, but follow one
another (A, B, C, D).
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was inspired by the vendor driver, but in the end never used for
anything.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This matches the flow of the vendor driver for newer hardware, and
doesn't seem to cause issues for the older parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer chips (8723bu/8192eu) has S0S1 settings which needs to be dealt
with during LC calibration.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8723bu also has it's own IQK calibration process. This is similar
in flow, but still different enough to warrent it's own
implementation, at least for now.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This adds some additional register definitions for 8723bu, as well as
a bit define for USB RXDMA aggregation in REG_RXDMA_AGG_PG_TH.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8192cu/rtl8188cu/rtl8723au use the same values, but 8723bu and
8192eu have their own.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix a silly bug where the debug level was overwritten rather than
amended for untested chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer generation chips require the firmware be notified before we
start the IQK calibration.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware command API differs slightly between new and old
devices. The new generation requires the size since there is no
extension bit encoded into the command number.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Likewise for 8723bu, use a pointer to the efuse.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the code easier to read and less error prone by using a pointer
to the efuse.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoid a negative conditional and an extra level of indentation in the
bigger part of the loop body.
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is enough to check for either illegal offset or illegal map address
because map address is a value derived from an offset:
map_addr = offset * 8
EFUSE_MAP_LEN = EFUSE_MAX_SECTION_8723A * 8
Leave just the check for an illegal map address because its upper
bound (EFUSE_MAP_LEN) is used also in a couple other places.
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The larger mailboxes also use a different set of mailbox commands.
This provides a list of the 64 bit commands.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In addition do not apply fixups for 8188/8191/8192 A-cut UMC parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This introduces additional register definitions for newer generation
chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Gen1 chips use a 16 bit mailbox extension register, for upto 48 bit
mailbox commands. The newer generation chips use a 32 bit mailbox
extension register instead, for upto 64 bit mailbox commands.
Handle writing the larger mailboxes.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The different RF module seems to require a different AGC table as well
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer chips seem to have some different mac registers, requiring
a different init table.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far this is just for 8723BU. It includes writing to a number of
registers I have seen no description for so far.
0x0064
0x0930
0x0944
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add 8723bu 1T radio init table. The vendor driver indicates that some
registers need special treatment for TFBGA90, TFBGA80, and TFBGA79
packaging. However the vendor driver never actually checks the package
type, so just stick to default values here.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Only 1st generation chips do provide USB interrupts, so do not try to
setup interrupts for newer chips (8192eu and 8723bu).
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8723bu, like the 8192eu, can also handle 1024 byte block writes.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement first stab at parsing the 8723bu's efuse.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This provides initial detection of 8723bu devices, and selects the
correct firmware image to load.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The newer generation chips have different interrupt registers.
Initialize this correct registers on 8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8192eu (and some other parts) will report an incorrect USB OUT
EP. This tells the chip to drop it - as per the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The logic for testing auto load failure in rtl8xxxu_auto_llt_table()
was inverted.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To match the flow of the vendor driver, move the LLT init to after the
firmware is started.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reorganizes the device initialization to init page boundaries
before starting the firmware. This matches the flow in the 8192eu
vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer chips can auto load the LLT table, it is no longer necessary to
build it manually in the driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This implements the rtl8192eu power on sequence, and splits it off
from the rtl8192cu/rtl8723au power on sequence.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rtl8192eu can handle 1024 byte block writes, unlike it's
predecessors (8192cu/8188cu).
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This identifies the chip vendors correctly and also picks the correct
firmware for rtl8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is the start of 8192eu support. For now just detect the device
and parse the efuse.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Smatch reports the following warning:
CHECK drivers/net/wireless/realtek/rtlwifi/rc.c
drivers/net/wireless/realtek/rtlwifi/rc.c:144 _rtl_rc_rate_set_series() warn: impossible condition '(wireless_mode == 256) => (0-255 == 256)'
This warning arises because commit acc6907b87a9 ("rtlwifi: Fix warning
from ieee80211_get_tx_rates() when using 5G") now checks the wireless
mode for WIRELESS_MODE_AC_ONLY (BIT(8)) in _rtl_rc_rate_set_series().
As a result, all quantities used to store the wireless mode must be u16.
This patch also reorders struct rtl_sta_info to save a little space.
Fixes: d76d65fd26 ("rtlwifi: fix broken VHT support")
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
passing rtl_stats by value is inefficient; the structure is over 300
bytes in size and generally just one field (packet_report_type)
is being accessed, so the pass by value is a relatively large overhead.
This change just affects just the rx_command_packet calls.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Routine rtl_addr_delay() uses delay statements in code that can
sleep. To improve system responsiveness, the various delay statements
are changed.
In addition, routines rtl_rfreg_delay() and rtl_bb_delay() are
rewritten to use the code in rtl_addr_delay() for most of their
input values.
Suggested-by: Byeoungwook Kim <quddnr145@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver rtl8821ae is loaded but not connected to any AP, it logs
a "firmware not ready to run" message roughly once a minute. To
eliminate logging this massage under normal debug conditions, the
degug level needed to print this message is increased.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are several copies of the 5G channel tables in this driver. These
are removed so that the tables in the core will be used. This change
also removes a useless message of "Channel 163 in Group not found".
The number of possible 5G channels was reduced from 54 to a better
value of 49 during the conversion.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver defines its own set of channel tables for the 5G band. With
this change, it will use those of the core.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver defines its owh copy of the 5G channels. Change it to use
the common definitions.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are 3 drivers in this family that have 5G radios. Each of them
defines local copies of the available channels. This patch adds the
two arrays to the core driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer chips have RF registers beyond the original 0x3f address.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All chips, except for 8812 require BIT(0) for resetting the MCU IO
wrapper. 8723b requires a more complicated reset sequence, so it will
need a custom reset function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 documentation says, the ieee80211_ops.start callback "must turn on
frame reception (for possibly enabled monitor interfaces.)". If not a single
monitor interface does not receive data frames.
Similarly we should not change the data reception based on the association
state.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add comments describing how REG_RXFLTMAP0, REG_RXFLTMAP1 and REG_RXFLTMAP2
work.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Monitor mode is enabled by handling the filter flags we get from mac80211 in
rtl8xxxu_configure_filter() and writing them to the RCR register.
By handling the filters, we can also stop setting the BSSID filters in the
association event.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8192cu driver doesn't read/write the REG_EFUSE_TEST register.
Neither does the rtl8188eu driver. Do it only for multifunc devices
RTL8723AU/RTL8723BU.
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was a leftover from the vendor driver that was never utilized.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to reset the 8051 in order for it to launch the fw on the
rtl8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rtl8xxxu_load_firmware() check the return value of kmemdup() and
error out with -ENOMEM in case of NULL to prevent a NULL pointer
dereference.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen