Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance rt2x00 infrastructure by adding explicit information
about used chipset interface to struct rt2x00_chip.
The new field will be used by rt2800 drivers for rt2800 library.
Also add commonly used rt2x00_intf_is_pci() and rt2x00_intf_is_usb()
helpers to make code easier to read (noticed by Ivo van Doorn).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance rt2x00 infrastructure by adding driver specific field to
struct rt2x00_dev.
The new field will be used by rt2800 drivers for chipset registers
access abstraction layer.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for the rt2860/rt3090 chipsets from Ralink.
Includes various patches from a lot of people who helped
getting this driver into the current shape.
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Mark Asselstine <asselsm@gmail.com>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calculated values for the ACK timeout and ACK
consume time are different then the values as
used by the Legacy drivers.
After testing from James Ledwith it appeared that
the calculated values caused a high amount of TX
failures, and the values from the Legacy drivers
were the most optimal to prevent TX failure due to
excessive retries.
The symptoms of this problem:
- Rate control module always falls back to 1Mbs
- Low throughput when bitrate was fixed
Possible side-effects (not confirmed but highly likely)
- Problems with DHCP
- Broken connections due to lack of probe response
This should fix at least:
Kernel bugzilla reports: [13362], [13009], [9273]
Fedora bugzilla reports: [443203]
but possible some additional bugs as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bss_info_changed() callback function no longer needs
to be atomic. Remove the scheduled work structure and
call into the driver directly.
Additionaly this makes the DRIVER_REQUIRE_SCHEDULED
flag redundant so it can be removed.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The configure_filter() callback function no longer needs
to be atomic. Remove the scheduled work structure and
call into the driver configure_filter() directly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements FIF_PSPOLL filter flag support in rt2x00 drivers,
which has been introduced in mac80211 (see
http://marc.info/?l=linux-wireless&m=124897986330807&w=2).
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch "Implement set_tim callback for all drivers" can cause kernel
oops in rt73usb_write_beacon. The oops is caused by one of the following
race conditions:
* In case of two near calls to set_tim: rt2x00lib_beacondone_iter is
cleaning the beacon skb, whereas rt73usb_write_beacon is still using it.
* In case of two near updates of beacon: first as the result of set_tim
and second as the result of a call from an application (e.g. hostapd).
This patch fixes the race condition by rearranging the update logic and
guarding rt2x00_intf->beacon->skb with a mutex.
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Small changes in signal level was not detected up by the
MOVING_AVERAGE() due to a rounding error, using 'int' type.
rt2x00lib_antenna_diversity_eval:
rssi: -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62
rssi_avg: -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57
The signal level reported back could be significantly (5dBm)
different from the actual value. A level +3dBm is the same as
double the AP output power.
Signed-off-by: Lars Ericsson <Lars_Ericsson@telia.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Antanna quality statistics is not handled correctly, which leads to
software diversity being shutdown completly.
The main problem is that during antenna diversity statistics can
be reset resulting in loosing the signal strength just before
evaluation.
rssi history is not updated correctly leading to incorrect comparison
material for basing antenna switching on.
Signed-off-by: Lars Ericsson <Lars_Ericsson@telia.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change rt2x00_rf_read() and rt2x00_rf_write() to subtract 1 from the rf
register number. This is needed because the rf registers are enumerated
starting with one. The size of the rf register cache is just enough to
hold all registers, so writing to the highest register was corrupting
memory. Add a check to make sure that the rf register number is valid.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: stable@kernel.org
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a bunch of spelling errors in the rt2x00 drivers
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The DEVICE_STATE_DISABLED_RADIO_HW flag is only read but never set,
it is an ancient part of one of the many versions of the rfkill implementations
in rt2x00. It is about time is disappears.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement set_tim callback for all rt2x00 drivers, this makes the
device wake up powersaving stations properly while in AP mode.
The only way to update the beacon is by simply calling mac80211 and
requesting the new beacon. This means the set_tim() event is mostly the
same as a beacon_done() event which was already defined in rt2x00lib.
Signed-off-by: Stefan Steuerwald <salsasepp@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the input_polldev from rt2x00 and replace it with
the rfkill interface offered by the wiphy structure. This
simplifies the entire rfkill handling in rt2x00 and allows
us to remove the CONFIG_RT2X00_LIB_RFKILL option and always
enables rfkill capabilities.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the last usage of beacon_int inside the iee80211_config
structure from rt2x00. The attempt is a bit hackish, and subject to
change in the future when the entire rt2x00_dev structure is
cleaned up and restructured.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_CONF_CHANGE_BEACON_INTERVAL was deprecated a month ago,
it is about time to remove all usage from the rt2x00 drivers and
use the correct beacon interval configuration through the bss_info
structure.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00_check_rev() was too specific for rt2500usb and rt73usb,
by adding the mask argument (instead of hardcoding it into
the function itself) we can use the function in rt2800usb as
well.
v2: Fix revision mask for rt2800usb
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for the rt2800usb chipset.
Current problems:
* Cannot scan 11n AP's
* No TX during first minute after association
* Broken Hardware encryption
Includes various patches from Mattias, Felix, Xose and Axel.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Axel Kollhofer <rain_maker@root-forum.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend rt2x00lib capabilities to support 802.11n,
it still lacks aggregation support, but that can
be added in the future.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware require L2 padding between header and payload
because both must be aligned to a 4-byte boundary. This hardware
also is easier during the RX path since we no longer need to
move the entire payload but rather only the header to remove
the padding (mac80211 only wants the payload to be 4-byte aligned).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pci_dev->irq and pci_name(pci_dev) access should be limited
to rt2x00pci only. This is more generic and allows a rt2x00 pci
driver to be controlled as PCI device but also as platform driver
(needed for rt2800pci SoC support).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The get_firmware_crc() callback function isn't flexible
enough when dealing with multiple firmware versions.
It might in some cases be possible that the firmware
file contains multiple CRC checksums.
Create the check_firmware() callback function where the driver
has complete freedom in how to validate the firmware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
provide rt2x00lib the possibility to kill a particular TX queue.
This can be useful when disabling the radio, but more importantly
will allow beaconing to be disabled when mac80211 requests this
(during scanning for example)
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With mac80211 handling all open interfaces during
suspend and resume we can simplify suspend/resume
within rt2x00lib.
The only thing rt2x00 needs to do is free up memory
during suspend and bring back the minimal required
components during resume.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "rev" field in chipset definition is an u32,
which means that rt2x00_rev() which returns that field
should be of the same type.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the standards only define 12 legacy rates, 32 is certainly
a sane upper limit and we don't need to use u64 everywhere. Add
sanity checking that no more than 32 rates are registered and
change the variables to u32 throughout.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As discussed on linux-wireless rt2x00 does not offer a true RFKILL key,
for that reason RFKILL support should be entirely removed.
The key which is attached to the hardware should be treated as normal
input device instead. Implement input_poll_dev support to poll the device
frequently. When the key status has changed report it as a SW event.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The set_key callback now seems rather odd, passing a MAC address
instead of a station struct, and a local address instead of a
vif struct. Change that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Bob Copeland <me@bobcopeland.com> [ath5k]
Acked-by: Ivo van Doorn <ivdoorn@gmail.com> [rt2x00]
Acked-by: Christian Lamparter <chunkeey@web.de> [p54]
Tested-by: Kalle Valo <kalle.valo@nokia.com> [iwl3945]
Tested-by: Samuel Ortiz <samuel@sortiz.org> [iwl3945]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_CRYPTO_COPY_IV is a bad name since it is part
of the driver requirements instead of a configuration option.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restrict drivers to only access link_qual structure during
link tuning. The contents of these fields are for the drivers
and all fields are allowed to be changed to values the driver
considers correct.
This means that some fields need to be moved outside of this
structure to restrict access only to rt2x00link itself.
This allows some code to be moved outside of the rt2x00.h header
and into rt2x00link.c.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The link_tuner() function will always call bbp_read()
at the start of the function. Because this is an
indirect register access has some costs attached
to it (especially for USB hardware).
We already store the value read from the register
into the vgc_level value inside the link structure.
Instead of reading from the register we can read that
field directly and base the tuner on that value.
This reduces the time the registers are locked with
the csr_mutex and speeds up the link_tuner processing.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move link and antenna tuning into a seperate file named rt2x00link.c,
this makes the interface to the link tuner a lot cleaner.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500usb supports hardware encryption.
rt2500usb supports up to 4 shared and pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Store retry limit values in the rt2x00dev structure.
This allows the removal of the FIXME where we assumed
the long retry is only used when working with RTS frames.
Instead we should check the current retry limit values
and decide if the required retry count for this frame
is a long or short retry.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding the used in/out endpoints
we should detect them by walking through all
available endpoints.
rt2800usb will gain the most out of this, because
the legacy drivers indicate that there are multiple
endpoints available.
However this code might benefit at least rt73usb as
well for the MIMO queues, and if we are really lucky
rt2500usb will benefit because for the TX and PRIO
queues.
Even if rt2500usb and rt73usb do not get better performance
after this patch, the endpoint detection still belongs to
rt2x00usb, and it shouldn't hurt to always try to detect
the available endpoints.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Indirect registers require multiple calls to the CSR
register in order to access the indirect registers.
This must be protected under a lock to prevent race
conditions which could cause invalid data to
be returned when reading from the indirect register or silent
failures when writing data to the indirect register.
USB drivers where already protected under a mutex,
so rename the mutex and make PCI drivers use the mutex
as well.
This now means that BBP and RF registers are no longer
accessible in interrupt context. That is not a bad
situation since the slow behavior of accessing
those registers means we don't _want_ to access them
in interrupt context either.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can optimize get_duration and get_duration_res
by making them a macro. They are really simple
calculation handlers so this doesn't matter much.
Often (especially in rt2400pci and rt2500pci,
the arguments are hardcoded, and the result value
is passed into other hardcoded values.
By making the functions a macro GCC can
optimize the entire thing much better.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge the callback functions init_txentry() and
init_rxentry(). This makes life in rt2x00lib a
lot simpler and we can cleanup several functions.
rt2x00pci contained "fake" FIELD definitions for
descriptor words. This is not flexible since it
assumes the driver will always have the same field
to indicate if a driver is available or not.
This should be dependent on the driver, and we
should add a callback function for this.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new configuration handling, and more specifically
splitting the configuration of the antenna from the normal
configuration steps allowed a BUG_ON() to be triggered
in the driver because the SW_DIVERSITY was send to the
driver. This fixes that by catching the value early in
rt2x00config.c and replacing it with a sensible value.
This also fixes a problem where the antenna is not being
initialized at all when the radio is enabled. Since it
no longer is part of the mac80211 configuration the
only place where rt2x00 configured it was the SW diversity
handler. Obviously this is broken for all non-diversity
hardware and breaks SW diversity due to a broken initialization.
When the radio is enabled the antenna will be configured
once as soon as the config() callback function is called.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can safely remove ieee80211_bss_conf from rt2x00_intf,
it is provided by mac80211 in ieee80211_vif as well.
(rt2x00_intf is the drv_priv field of ieee80211_vif).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement latest changed from mac80211 configuration
handling to optmize configuration handling in rt2x00.
* Remove set_retry_limit callback function, handled
through config()
* Move config_antenna to its own callback function,
it isn't handled by mac80211 anymore
* Use IEEE80211_CONF_CHANGED_* flags and remove manual
checks
* Removed deprecated short slot setting through config()
and put it in config_erp() through which mac80211 now
configures it
* Remove config_phymode() and move contents to config_erp()
since it only managed the basic rates which is now
determined by mac80211 through config_erp().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bartlomiej Zolnierkiewicz