The alternative code patching doesn't check if the replaced instruction
uses a pc relative literal. This could cause silent corruption in the
instruction stream as the instruction will be executed from a different
address than what it was compiled for. Catch all such cases.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Suggested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Right now we run through the work around checks on a CPU
from __cpuinfo_store_cpu. There are some problems with that:
1) We initialise the system wide CPU feature registers only after the
Boot CPU updates its cpuinfo. Now, if a work around depends on the
variance of a CPU ID feature (e.g, check for Cache Line size mismatch),
we have no way of performing it cleanly for the boot CPU.
2) It is out of place, invoked from __cpuinfo_store_cpu() in cpuinfo.c. It
is not an obvious place for that.
This patch rearranges the CPU specific capability(aka work around) checks.
1) At the moment we use verify_local_cpu_capabilities() to check if a new
CPU has all the system advertised features. Use this for the secondary CPUs
to perform the work around check. For that we rename
verify_local_cpu_capabilities() => check_local_cpu_capabilities()
which:
If the system wide capabilities haven't been initialised (i.e, the CPU
is activated at the boot), update the system wide detected work arounds.
Otherwise (i.e a CPU hotplugged in later) verify that this CPU conforms to the
system wide capabilities.
2) Boot CPU updates the work arounds from smp_prepare_boot_cpu() after we have
initialised the system wide CPU feature values.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This is a cosmetic change to rename the functions dealing with
the errata work arounds to be more consistent with their naming.
1) check_local_cpu_errata() => update_cpu_errata_workarounds()
check_local_cpu_errata() actually updates the system's errata work
arounds. So rename it to reflect the same.
2) verify_local_cpu_errata() => verify_local_cpu_errata_workarounds()
Use errata_workarounds instead of _errata.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Right now we use 0 as the safe value for CTR_EL0:L1Ip, which is
not defined at the moment. The safer value for the L1Ip should be
the weakest of the policies, which happens to be AIVIVT. While at it,
fix the comment about safe_val.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
1. Remove the old binding code.
2. Read the nid of cpu0 from dts.
3. Fallback the nid of cpu0 to 0 when numa=off is set in bootargs.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
numa_init may return error because of numa configuration error. So "No
NUMA configuration found" is inaccurate. In fact, specific configuration
error information should be immediately printed by the testing branch.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
By using a common attr_groups array, the common arm_pmu code can set up
common files (e.g. cpumask) for us in subsequent patches.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.
This patch makes use of these across arm64 to make code shorter and
clearer. For sequences with a trailing ISB, the existing isb() macro is
also used so that asm blocks can be removed entirely.
A few uses of inline assembly for msr/mrs are left as-is. Those
manipulating sp_el0 for the current thread_info value have special
clobber requiremends.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds static keys transparently for all the cpu_hwcaps
features by implementing an array of default-false static keys and
enabling them when detected. The cpus_have_cap() check uses the static
keys if the feature being checked is a constant, otherwise the compiler
generates the bitmap test.
Because of the early call to static_branch_enable() via
check_local_cpu_errata() -> update_cpu_capabilities(), the jump labels
are initialised in cpuinfo_store_boot_cpu().
Cc: Will Deacon <will.deacon@arm.com>
Cc: Suzuki K. Poulose <Suzuki.Poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, enabling stacktrace of a kprobe events generates warning:
echo stacktrace > /sys/kernel/debug/tracing/trace_options
echo "p xhci_irq" > /sys/kernel/debug/tracing/kprobe_events
echo 1 > /sys/kernel/debug/tracing/events/kprobes/enable
save_stack_trace_regs() not implemented yet.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 0 at ../kernel/stacktrace.c:74 save_stack_trace_regs+0x3c/0x48
Modules linked in:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.8.0-rc4-dirty #5128
Hardware name: ARM Juno development board (r1) (DT)
task: ffff800975dd1900 task.stack: ffff800975ddc000
PC is at save_stack_trace_regs+0x3c/0x48
LR is at save_stack_trace_regs+0x3c/0x48
pc : [<ffff000008126c64>] lr : [<ffff000008126c64>] pstate: 600003c5
sp : ffff80097ef52c00
Call trace:
save_stack_trace_regs+0x3c/0x48
__ftrace_trace_stack+0x168/0x208
trace_buffer_unlock_commit_regs+0x5c/0x7c
kprobe_trace_func+0x308/0x3d8
kprobe_dispatcher+0x58/0x60
kprobe_breakpoint_handler+0xbc/0x18c
brk_handler+0x50/0x90
do_debug_exception+0x50/0xbc
This patch implements save_stack_trace_regs(), so that stacktrace of a
kprobe events can be obtained.
After this patch, there is no warning and we can see the stacktrace for
kprobe events in trace buffer.
more /sys/kernel/debug/tracing/trace
<idle>-0 [004] d.h. 1356.000496: p_xhci_irq_0:(xhci_irq+0x0/0x9ac)
<idle>-0 [004] d.h. 1356.000497: <stack trace>
=> xhci_irq
=> __handle_irq_event_percpu
=> handle_irq_event_percpu
=> handle_irq_event
=> handle_fasteoi_irq
=> generic_handle_irq
=> __handle_domain_irq
=> gic_handle_irq
=> el1_irq
=> arch_cpu_idle
=> default_idle_call
=> cpu_startup_entry
=> secondary_start_kernel
=>
Tested-by: David A. Long <dave.long@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit b5fe242972 ("arm64: kernel: fix style issues in sleep.S")
changed the linkage of _cpu_resume() to local, even though the symbol
is also referenced from hibernate.c. So revert this change.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Single-step traps to userspace (e.g. via ptrace) are expected to use
the TRAP_TRACE for the si_code field of the siginfo, as opposed to
TRAP_HWBRPT that we report currently.
Fix the reported value, which has no effect on existing and legacy
builds of GDB.
Reported-by: Yao Qi <yao.qi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the only remaining occurrences of the use of callee saved
registers are on the primary boot path, add a comment to the code
which register is used for what.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Instead of stashing the value of the link register in x28 before setting
up the stack and calling into C code, create an ordinary PCS compatible
stack frame so that we can push the return address onto the stack.
Since exception handlers require a stack as well, assign the stack pointer
register before installing the vector table.
Note that this accounts for the difference between THREAD_START_SP and
THREAD_SIZE, given that the stack pointer is always decremented before
calling into any C code.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Keeping __PHYS_OFFSET in x24 is actually less clear than simply taking
the value of __PHYS_OFFSET using an adrp instruction in the three places
that we need it. So change that.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Using x27 for passing to __enable_mmu what is essentially the return
address makes the code look more complicated than it needs to be. So
switch to x30/lr, and update the secondary and cpu_resume call sites to
simply call __enable_mmu as an ordinary function, with a bl instruction.
This requires the callers to be covered by .idmap.text.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The KASLR processing is only used by the primary boot path, and
complements the processing that takes place in __primary_switch().
Move the two parts together, to make the code easier to understand.
Also, fix up a minor whitespace issue.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: fixed conflict with -rc3 due to lack of fd363bd417]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The function el2_setup() passes its return value in register w20, and
in the two cases where the caller actually cares about this return value,
it is passed into set_cpu_boot_mode_flag() [almost] directly, which
expects its input in w20 as well.
So there is no reason to use a 'special' callee saved register here, but
we can simply follow the PCS for return value and first argument,
respectively.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This fixes a number of style issues in sleep.S. No functional changes are
intended:
- replace absolute literal references with relative references in
__cpu_suspend_enter(), which executes from its virtual address
- replace explicit lr assignment plus branch with bl in cpu_resume(), which
aligns it with stext() and secondary_startup()
- don't export _cpu_resume()
- use adr_l for mpidr_hash reference, and fix the incorrect accompanying
comment, which has been out of date since commit cabe1c81ea ("arm64:
Change cpu_resume() to enable mmu early then access sleep_sp by va")
- replace leading spaces with tabs, and add a bit of whitespace for
readability
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit e19a6ee246 ("arm64: kernel: Save and restore UAO and
addr_limit on exception entry") states that exception handler inherits
the original PSTATE.UAO value, so UAO needes to be reset
explicitly. However, ARM 8.2 Extension documentation says:
PSTATE.UAO is copied to SPSR_ELx.UAO and is then set to 0 on an
exception taken from AArch64 to AArch64
so hardware already does the right thing.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64 debug monitor initialisation code uses a CPU hotplug notifier
to clear the OS lock when CPUs come online.
This patch converts the code to the new hotplug mechanism.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64 hw_breakpoint implementation uses a CPU hotplug notifier to
reset the {break,watch}point registers when CPUs come online.
This patch converts the code to the new hotplug mechanism, whilst moving
the invocation earlier to remove the need to disable IRQs explicitly in
the driver (which could cause havok if we trip a watchpoint in an IRQ
handler whilst restoring the debug register state).
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When TIF_SINGLESTEP is set for a task, the single-step state machine is
enabled and we must take care not to reset it to the active-not-pending
state if it is already in the active-pending state.
Unfortunately, that's exactly what user_enable_single_step does, by
unconditionally setting the SS bit in the SPSR for the current task.
This causes failures in the GDB testsuite, where GDB ends up missing
expected step traps if the instruction being stepped generates another
trap, e.g. PTRACE_EVENT_FORK from an SVC instruction.
This patch fixes the problem by preserving the current state of the
stepping state machine when TIF_SINGLESTEP is set on the current thread.
Cc: <stable@vger.kernel.org>
Reported-by: Yao Qi <yao.qi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Expose the arm64_ftr_reg struct covering CTR_EL0 outside of cpufeature.o
so that other code can refer to it directly (i.e., without performing the
binary search)
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Constify the arm64_ftr_regs array, by moving the mutable arm64_ftr_reg
fields out of the array itself. This also streamlines the bsearch, since
the entire array can be covered by fewer cachelines. Moving the payload
out of the array also allows us to have special explicitly defined
struct instance in case other code needs to refer to it directly.
Note that this replaces the runtime sorting of the array with a runtime
BUG() check whether the array is sorted correctly in the code.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64_ftr_bits structures are never modified, so make them read-only.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The make rpm target depends on proper UTS_MACHINE definition. Also, use
the variable in arch/arm64/kernel/setup.c, so that it's not accidentally
removed in the future.
Reported-and-tested-by: Fabian Vogt <fvogt@suse.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that we use the MPIDR to resume on the same CPU that we hibernated on,
we no longer need to refuse to hibernate if the boot cpu is offline. (Which
we can't possibly know if kexec causes logical CPUs to be renumbered).
This reverts commit 1fe492ce64.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
disable_nonboot_cpus() assumes that the lowest numbered online CPU is
the boot CPU, and that this is the correct CPU to run any power
management code on.
On arm64 CPU0 can be taken offline. For hibernate/resume this means we
may hibernate on a CPU other than CPU0. If the system is rebooted with
kexec 'CPU0' will be assigned to a different CPU. This complicates
hibernate/resume as now we can't trust the CPU numbers.
We currently forbid hibernate if CPU0 has been hotplugged out to avoid
this situation without kexec.
Save the MPIDR of the CPU we hibernated on in the hibernate arch-header,
use hibernate_resume_nonboot_cpu_disable() to direct which CPU we should
resume on based on the MPIDR of the CPU we hibernated on. This allows us to
hibernate/resume on any CPU, even if the logical numbers have been
shuffled by kexec.
Signed-off-by: James Morse <james.morse@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Follow the example set by x86 in commit 9ccaf77cf0 ("x86/mm:
Always enable CONFIG_DEBUG_RODATA and remove the Kconfig option"), and
make these protections a fundamental security feature rather than an
opt-in. This also results in a minor code simplification.
For those rare cases when users wish to disable this protection (e.g.
for debugging), this can be done by passing 'rodata=off' on the command
line.
As DEBUG_RODATA_ALIGN is only intended to address a performance/memory
tradeoff, and does not affect correctness, this is left user-selectable.
DEBUG_MODULE_RONX is also left user-selectable until the core code
provides a boot-time option to disable the protection for debugging
use-cases.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Kdump(kexec-tools) parses /proc/iomem to identify all the memory regions
on the system. Since the current kernel names "nomap" regions, like UEFI
runtime services code/data, as "System RAM," kexec-tools sets up elf core
header to include them in a crash dump file (/proc/vmcore).
Then crash dump kernel parses UEFI memory map again, re-marks those regions
as "nomap" and does not create a memory mapping for them unlike the other
areas of System RAM. In this case, copying /proc/vmcore through
copy_oldmem_page() on crash dump kernel will end up with a kernel abort,
as reported in [1].
This patch names all the "nomap" regions explicitly as "reserved" so that
we can exclude them from a crash dump file. acpi_os_ioremap() must also
be modified because those regions have WB attributes [2].
Apart from kdump, this change also matches x86's use of acpi (and
/proc/iomem).
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2016-August/448186.html
[2] http://lists.infradead.org/pipermail/linux-arm-kernel/2016-August/450089.html
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
DEBUG_PAGEALLOC removes the valid bit of page table entries to prevent
any access to unallocated memory. Hibernate uses this as a hint that those
pages don't need to be saved/restored. This patch adds the
kernel_page_present() function it uses.
hibernate.c copies the resume kernel's linear map for use during restore.
Add _copy_pte() to fill-in the holes made by DEBUG_PAGEALLOC in the resume
kernel, so we can restore data the original kernel had at these addresses.
Finally, DEBUG_PAGEALLOC means the linear-map alias of KERNEL_START to
KERNEL_END may have holes in it, so we can't lazily clean this whole
area to the PoC. Only clean the new mmuoff region, and the kernel/kvm
idmaps.
This reverts commit da24eb1f3f.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Resume from hibernate needs to clean any text executed by the kernel with
the MMU off to the PoC. Collect these functions together into the
.idmap.text section as all this code is tightly coupled and also needs
the same cleaning after resume.
Data is more complicated, secondary_holding_pen_release is written with
the MMU on, clean and invalidated, then read with the MMU off. In contrast
__boot_cpu_mode is written with the MMU off, the corresponding cache line
is invalidated, so when we read it with the MMU on we don't get stale data.
These cache maintenance operations conflict with each other if the values
are within a Cache Writeback Granule (CWG) of each other.
Collect the data into two sections .mmuoff.data.read and .mmuoff.data.write,
the linker script ensures mmuoff.data.write section is aligned to the
architectural maximum CWG of 2KB.
Signed-off-by: James Morse <james.morse@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Each time new section markers are added, kernel/vmlinux.ld.S is updated,
and new extern char __start_foo[] definitions are scattered through the
tree.
Create asm/include/sections.h to collect these definitions (and include
the existing asm-generic version).
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Whenever we are hitting a kprobe from a none-kprobe debug exception handler,
we hit an infinite occurrences of "Unexpected kernel single-step exception
at EL1"
PSTATE.D is debug exception mask bit. It is set whenever we enter into an
exception mode. When it is set then Watchpoint, Breakpoint, and Software
Step exceptions are masked. However, software Breakpoint Instruction
exceptions can never be masked. Therefore, if we ever execute a BRK
instruction, irrespective of D-bit setting, we will be receiving a
corresponding breakpoint exception.
For example:
- We are executing kprobe pre/post handler, and kprobe has been inserted in
one of the instruction of a function called by handler. So, it executes
BRK instruction and we land into the case of KPROBE_REENTER. (This case is
already handled by current code)
- We are executing uprobe handler or any other BRK handler such as in
WARN_ON (BRK BUG_BRK_IMM), and we trace that path using kprobe.So, we
enter into kprobe breakpoint handler,from another BRK handler.(This case
is not being handled currently)
In all such cases kprobe breakpoint exception will be raised when we were
already in debug exception mode. SPSR's D bit (bit 9) shows the value of
PSTATE.D immediately before the exception was taken. So, in above example
cases we would find it set in kprobe breakpoint handler. Single step
exception will always be followed by a kprobe breakpoint exception.However,
it will only be raised gracefully if we clear D bit while returning from
breakpoint exception. If D bit is set then, it results into undefined
exception and when it's handler enables dbg then single step exception is
generated, however it will never be handled(because address does not match
and therefore treated as unexpected).
This patch clears D-flag unconditionally in setup_singlestep, so that we can
always get single step exception correctly after returning from breakpoint
exception. Additionally, it also removes D-flag set statement for
KPROBE_REENTER return path, because debug exception for KPROBE_REENTER will
always take place in a debug exception state. So, D-flag will already be set
in this case.
Acked-by: Sandeepa Prabhu <sandeepa.s.prabhu@gmail.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When CONFIG_RANDOMIZE_BASE is selected, we modify the page tables to remap the
kernel at a newly-chosen VA range. We do this with the MMU disabled, but do not
invalidate TLBs prior to re-enabling the MMU with the new tables. Thus the old
mappings entries may still live in TLBs, and we risk violating
Break-Before-Make requirements, leading to TLB conflicts and/or other issues.
We invalidate TLBs when we uninsall the idmap in early setup code, but prior to
this we are subject to issues relating to the Break-Before-Make violation.
Avoid these issues by invalidating the TLBs before the new mappings can be
used by the hardware.
Fixes: f80fb3a3d5 ("arm64: add support for kernel ASLR")
Cc: <stable@vger.kernel.org> # 4.6+
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Storing this value will help prevent unwinders from getting out of sync
with the function graph tracer ret_stack. Now instead of needing a
stateful iterator, they can compare the return address pointer to find
the right ret_stack entry.
Note that an array of 50 ftrace_ret_stack structs is allocated for every
task. So when an arch implements this, it will add either 200 or 400
bytes of memory usage per task (depending on whether it's a 32-bit or
64-bit platform).
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/a95cfcc39e8f26b89a430c56926af0bb217bc0a1.1471607358.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Make HAVE_FUNCTION_GRAPH_FP_TEST a normal define, independent from
kconfig. This removes some config file pollution and simplifies the
checking for the fp test.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/2c4e5f05054d6d367f702fd153af7a0109dd5c81.1471607358.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, x25 and x26 hold the physical addresses of idmap_pg_dir
and swapper_pg_dir, respectively, when running early boot code. But
having registers with 'global' scope in files that contain different
sections with different lifetimes, and that are called by different
CPUs at different times is a bit messy, especially since stashing the
values does not buy us anything in terms of code size or clarity.
So simply replace each reference to x25 or x26 with an adrp instruction
referring to idmap_pg_dir or swapper_pg_dir directly.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
These objects are set during initialization, thereafter are read only.
Previously I only want to mark vdso_pages, vdso_spec, vectors_page and
cpu_ops as __read_mostly from performance point of view. Then inspired
by Kees's patch[1] to apply more __ro_after_init for arm, I think it's
better to mark them as __ro_after_init. What's more, I find some more
objects are also read only after init. So apply __ro_after_init to all
of them.
This patch also removes global vdso_pagelist and tries to clean up
vdso_spec[] assignment code.
[1] http://www.spinics.net/lists/arm-kernel/msg523188.html
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The vm_special_mapping spec which is used for aarch32 vectors page is
never modified, so mark it as const.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
It is not needed after booting, this patch moves the alloc_vectors_page
function to the __init section.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Use the builtin_platform_driver() to simplify code.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently ret_fast_syscall, work_pending, and ret_to_user form an ad-hoc
state machine that can be difficult to reason about due to duplicated
code and a large number of branch targets.
This patch factors the common logic out into the existing
do_notify_resume function, converting the code to C in the process,
making the code more legible.
This patch tries to closely mirror the existing behaviour while using
the usual C control flow primitives. As local_irq_{disable,enable} may
be instrumented, we balance exception entry (where we will almost most
likely enable IRQs) with a call to trace_hardirqs_on just before the
return to userspace.
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In break_before_make_ttbr_switch we perform broadcast TLB maintenance
for the inner shareable domain, and use a DSB ISH to complete this.
However, at the point we execute this, secondary CPUs are either
physically offline, or executing code outside of the kernel. Upon
entering the kernel, secondary CPUs will invalidate their TLBs before
enabling their MMUs.
Thus we do not need to invalidate TLBs of other CPUs, and as with
idmap_cpu_replace_ttbr1 we can reduce the scope of maintenance to the
TLBs of the local CPU. This keeps our TLB maintenance code consistent,
and is a minor optimisation.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Literal loads of virtual addresses are subject to runtime relocation when
CONFIG_RELOCATABLE=y, and given that the relocation routines run with the
MMU and caches enabled, literal loads of relocated values performed with
the MMU off are not guaranteed to return the latest value unless the
memory covering the literal is cleaned to the PoC explicitly.
So defer the literal load until after the MMU has been enabled, just like
we do for primary_switch() and secondary_switch() in head.S.
Fixes: 1e48ef7fcc ("arm64: add support for building vmlinux as a relocatable PIE binary")
Cc: <stable@vger.kernel.org> # 4.6+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In create_safe_exec_page(), we create a copy of the hibernate exit text,
along with some page tables to map this via TTBR0. We then install the
new tables in TTBR0.
In swsusp_arch_resume() we call create_safe_exec_page() before trying a
number of operations which may fail (e.g. copying the linear map page
tables). If these fail, we bail out of swsusp_arch_resume() and return
an error code, but leave TTBR0 as-is. Subsequently, the core hibernate
code will call free_basic_memory_bitmaps(), which will free all of the
memory allocations we made, including the page tables installed in
TTBR0.
Thus, we may have TTBR0 pointing at dangling freed memory for some
period of time. If the hibernate attempt was triggered by a user
requesting a hibernate test via the reboot syscall, we may return to
userspace with the clobbered TTBR0 value.
Avoid these issues by reorganising swsusp_arch_resume() such that we
have no failure paths after create_safe_exec_page(). We also add a check
that the zero page allocation succeeded, matching what we have for other
allocations.
Fixes: 82869ac57b ("arm64: kernel: Add support for hibernate/suspend-to-disk")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # 4.7+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In create_safe_exec_page we install a set of global mappings in TTBR0,
then subsequently invalidate TLBs. While TTBR0 points at the zero page,
and the TLBs should be free of stale global entries, we may have stale
ASID-tagged entries (e.g. from the EFI runtime services mappings) for
the same VAs. Per the ARM ARM these ASID-tagged entries may conflict
with newly-allocated global entries, and we must follow a
Break-Before-Make approach to avoid issues resulting from this.
This patch reworks create_safe_exec_page to invalidate TLBs while the
zero page is still in place, ensuring that there are no potential
conflicts when the new TTBR0 value is installed. As a single CPU is
online while this code executes, we do not need to perform broadcast TLB
maintenance, and can call local_flush_tlb_all(), which also subsumes
some barriers. The remaining assembly is converted to use write_sysreg()
and isb().
Other than this, we safely manipulate TTBRs in the hibernate dance. The
code we install as part of the new TTBR0 mapping (the hibernated
kernel's swsusp_arch_suspend_exit) installs a zero page into TTBR1,
invalidates TLBs, then installs its preferred value. Upon being restored
to the middle of swsusp_arch_suspend, the new image will call
__cpu_suspend_exit, which will call cpu_uninstall_idmap, installing the
zero page in TTBR0 and invalidating all TLB entries.
Fixes: 82869ac57b ("arm64: kernel: Add support for hibernate/suspend-to-disk")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # 4.7+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Executing from a non-executable area gives an ugly message:
lkdtm: Performing direct entry EXEC_RODATA
lkdtm: attempting ok execution at ffff0000084c0e08
lkdtm: attempting bad execution at ffff000008880700
Bad mode in Synchronous Abort handler detected on CPU2, code 0x8400000e -- IABT (current EL)
CPU: 2 PID: 998 Comm: sh Not tainted 4.7.0-rc2+ #13
Hardware name: linux,dummy-virt (DT)
task: ffff800077e35780 ti: ffff800077970000 task.ti: ffff800077970000
PC is at lkdtm_rodata_do_nothing+0x0/0x8
LR is at execute_location+0x74/0x88
The 'IABT (current EL)' indicates the error but it's a bit cryptic
without knowledge of the ARM ARM. There is also no indication of the
specific address which triggered the fault. The increase in kernel
page permissions makes hitting this case more likely as well.
Handling the case in the vectors gives a much more familiar looking
error message:
lkdtm: Performing direct entry EXEC_RODATA
lkdtm: attempting ok execution at ffff0000084c0840
lkdtm: attempting bad execution at ffff000008880680
Unable to handle kernel paging request at virtual address ffff000008880680
pgd = ffff8000089b2000
[ffff000008880680] *pgd=00000000489b4003, *pud=0000000048904003, *pmd=0000000000000000
Internal error: Oops: 8400000e [#1] PREEMPT SMP
Modules linked in:
CPU: 1 PID: 997 Comm: sh Not tainted 4.7.0-rc1+ #24
Hardware name: linux,dummy-virt (DT)
task: ffff800077f9f080 ti: ffff800008a1c000 task.ti: ffff800008a1c000
PC is at lkdtm_rodata_do_nothing+0x0/0x8
LR is at execute_location+0x74/0x88
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Because the arm64 calling standard allows stacked function arguments to be
anywhere in the stack frame, do not attempt to duplicate the stack frame for
jprobes handler functions.
Documentation changes to describe this issue have been broken out into a
separate patch in order to simultaneously address them in other
architecture(s).
Signed-off-by: David A. Long <dave.long@linaro.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Enable the hard limit of cpu count by set boot options nr_cpus=x
on arm64, and make a minor change about message when total number
of cpu exceeds the limit.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reported-by: Shiyuan Hu <hushiyuan@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- Fix HugeTLB leak due to CoW and PTE_RDONLY mismatch
- Avoid accessing unmapped FDT fields when checking validity
- Correctly account for vDSO AUX entry in ARCH_DLINFO
- Fix kallsyms with absolute expressions in linker script
- Kill unnecessary symbol-based relocs in vmlinux
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJXpFZ5AAoJELescNyEwWM0PI4IALsTuHRzClOSMDLiqMUj8t+5
WNAcqybxAjCOVxAHckhweju++TeJBxcRH1nvBoNwiHIdHTv4fq1TZ3PeEq9kWMg5
JbKjYjvd9dW8k6LXMya8iXCYtG3kzbNejkNpOTVebC86yvas1IiEjNb/ztPdhJeM
HBSOkhfk8RcskfNxhuscZzGXbbdH9/R+XSTNRHN/RwCZH8PlInmduD9BbMvDhZyP
NLFonD2IgQ4as1kYG/HdIcw0BamHiURjd043+gyoqMvm7JjPksRzlQnr91SMkX17
LykXjHYPi2Me3aTrZ1NtkUNd5FHLHZ6/b9Wg6nA19d5KWkd3ER9uSJqGxkkbnt0=
=dtGK
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- fix HugeTLB leak due to CoW and PTE_RDONLY mismatch
- avoid accessing unmapped FDT fields when checking validity
- correctly account for vDSO AUX entry in ARCH_DLINFO
- fix kallsyms with absolute expressions in linker script
- kill unnecessary symbol-based relocs in vmlinux
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix copy-on-write referencing in HugeTLB
arm64: mm: avoid fdt_check_header() before the FDT is fully mapped
arm64: Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO
arm64: relocatable: suppress R_AARCH64_ABS64 relocations in vmlinux
arm64: vmlinux.lds: make __rela_offset and __dynsym_offset ABSOLUTE
VGIC implementation.
- s390: support for trapping software breakpoints, nested virtualization
(vSIE), the STHYI opcode, initial extensions for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots of cleanups,
preliminary to this and the upcoming support for hardware virtualization
extensions.
- x86: support for execute-only mappings in nested EPT; reduced vmexit
latency for TSC deadline timer (by about 30%) on Intel hosts; support for
more than 255 vCPUs.
- PPC: bugfixes.
The ugly bit is the conflicts. A couple of them are simple conflicts due
to 4.7 fixes, but most of them are with other trees. There was definitely
too much reliance on Acked-by here. Some conflicts are for KVM patches
where _I_ gave my Acked-by, but the worst are for this pull request's
patches that touch files outside arch/*/kvm. KVM submaintainers should
probably learn to synchronize better with arch maintainers, with the
latter providing topic branches whenever possible instead of Acked-by.
This is what we do with arch/x86. And I should learn to refuse pull
requests when linux-next sends scary signals, even if that means that
submaintainers have to rebase their branches.
Anyhow, here's the list:
- arch/x86/kvm/vmx.c: handle_pcommit and EXIT_REASON_PCOMMIT was removed
by the nvdimm tree. This tree adds handle_preemption_timer and
EXIT_REASON_PREEMPTION_TIMER at the same place. In general all mentions
of pcommit have to go.
There is also a conflict between a stable fix and this patch, where the
stable fix removed the vmx_create_pml_buffer function and its call.
- virt/kvm/kvm_main.c: kvm_cpu_notifier was removed by the hotplug tree.
This tree adds kvm_io_bus_get_dev at the same place.
- virt/kvm/arm/vgic.c: a few final bugfixes went into 4.7 before the
file was completely removed for 4.8.
- include/linux/irqchip/arm-gic-v3.h: this one is entirely our fault;
this is a change that should have gone in through the irqchip tree and
pulled by kvm-arm. I think I would have rejected this kvm-arm pull
request. The KVM version is the right one, except that it lacks
GITS_BASER_PAGES_SHIFT.
- arch/powerpc: what a mess. For the idle_book3s.S conflict, the KVM
tree is the right one; everything else is trivial. In this case I am
not quite sure what went wrong. The commit that is causing the mess
(fd7bacbca4, "KVM: PPC: Book3S HV: Fix TB corruption in guest exit
path on HMI interrupt", 2016-05-15) touches both arch/powerpc/kernel/
and arch/powerpc/kvm/. It's large, but at 396 insertions/5 deletions
I guessed that it wasn't really possible to split it and that the 5
deletions wouldn't conflict. That wasn't the case.
- arch/s390: also messy. First is hypfs_diag.c where the KVM tree
moved some code and the s390 tree patched it. You have to reapply the
relevant part of commits 6c22c98637, plus all of e030c1125e, to
arch/s390/kernel/diag.c. Or pick the linux-next conflict
resolution from http://marc.info/?l=kvm&m=146717549531603&w=2.
Second, there is a conflict in gmap.c between a stable fix and 4.8.
The KVM version here is the correct one.
I have pushed my resolution at refs/heads/merge-20160802 (commit
3d1f53419842) at git://git.kernel.org/pub/scm/virt/kvm/kvm.git.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXoGm7AAoJEL/70l94x66DugQIAIj703ePAFepB/fCrKHkZZia
SGrsBdvAtNsOhr7FQ5qvvjLxiv/cv7CymeuJivX8H+4kuUHUllDzey+RPHYHD9X7
U6n1PdCH9F15a3IXc8tDjlDdOMNIKJixYuq1UyNZMU6NFwl00+TZf9JF8A2US65b
x/41W98ilL6nNBAsoDVmCLtPNWAqQ3lajaZELGfcqRQ9ZGKcAYOaLFXHv2YHf2XC
qIDMf+slBGSQ66UoATnYV2gAopNlWbZ7n0vO6tE2KyvhHZ1m399aBX1+k8la/0JI
69r+Tz7ZHUSFtmlmyByi5IAB87myy2WQHyAPwj+4vwJkDGPcl0TrupzbG7+T05Y=
=42ti
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
- ARM: GICv3 ITS emulation and various fixes. Removal of the
old VGIC implementation.
- s390: support for trapping software breakpoints, nested
virtualization (vSIE), the STHYI opcode, initial extensions
for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots
of cleanups, preliminary to this and the upcoming support for
hardware virtualization extensions.
- x86: support for execute-only mappings in nested EPT; reduced
vmexit latency for TSC deadline timer (by about 30%) on Intel
hosts; support for more than 255 vCPUs.
- PPC: bugfixes.
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (302 commits)
KVM: PPC: Introduce KVM_CAP_PPC_HTM
MIPS: Select HAVE_KVM for MIPS64_R{2,6}
MIPS: KVM: Reset CP0_PageMask during host TLB flush
MIPS: KVM: Fix ptr->int cast via KVM_GUEST_KSEGX()
MIPS: KVM: Sign extend MFC0/RDHWR results
MIPS: KVM: Fix 64-bit big endian dynamic translation
MIPS: KVM: Fail if ebase doesn't fit in CP0_EBase
MIPS: KVM: Use 64-bit CP0_EBase when appropriate
MIPS: KVM: Set CP0_Status.KX on MIPS64
MIPS: KVM: Make entry code MIPS64 friendly
MIPS: KVM: Use kmap instead of CKSEG0ADDR()
MIPS: KVM: Use virt_to_phys() to get commpage PFN
MIPS: Fix definition of KSEGX() for 64-bit
KVM: VMX: Add VMCS to CPU's loaded VMCSs before VMPTRLD
kvm: x86: nVMX: maintain internal copy of current VMCS
KVM: PPC: Book3S HV: Save/restore TM state in H_CEDE
KVM: PPC: Book3S HV: Pull out TM state save/restore into separate procedures
KVM: arm64: vgic-its: Simplify MAPI error handling
KVM: arm64: vgic-its: Make vgic_its_cmd_handle_mapi similar to other handlers
KVM: arm64: vgic-its: Turn device_id validation into generic ID validation
...
* pci/resource:
unicore32/PCI: Remove pci=firmware command line parameter handling
ARM/PCI: Remove arch-specific pcibios_enable_device()
ARM64/PCI: Remove arch-specific pcibios_enable_device()
MIPS/PCI: Claim bus resources on PCI_PROBE_ONLY set-ups
ARM/PCI: Claim bus resources on PCI_PROBE_ONLY set-ups
PCI: generic: Claim bus resources on PCI_PROBE_ONLY set-ups
PCI: Add generic pci_bus_claim_resources()
alx: Use pci_(request|release)_mem_regions
ethernet/intel: Use pci_(request|release)_mem_regions
GenWQE: Use pci_(request|release)_mem_regions
lpfc: Use pci_(request|release)_mem_regions
NVMe: Use pci_(request|release)_mem_regions
PCI: Add helpers to request/release memory and I/O regions
PCI: Extending pci=resource_alignment to specify device/vendor IDs
sparc/PCI: Implement pci_resource_to_user() with pcibios_resource_to_bus()
powerpc/pci: Implement pci_resource_to_user() with pcibios_resource_to_bus()
microblaze/PCI: Implement pci_resource_to_user() with pcibios_resource_to_bus()
PCI: Unify pci_resource_to_user() declarations
microblaze/PCI: Remove useless __pci_mmap_set_pgprot()
powerpc/pci: Remove __pci_mmap_set_pgprot()
PCI: Ignore write combining when mapping I/O port space
- Removal of most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to call
it if they have special needs.
- Use pr_fmt on all the DT core print statements.
- CoreSight binding doc improvements to block name descriptions.
- Add dt_to_config script which can parse dts files and list
corresponding kernel config options.
- Fix memory leak hit with a PowerMac DT.
- Correct a bunch of STMicro compatible strings to use the correct
vendor prefix.
- Fix DA9052 PMIC binding doc to match what is actually used in dts
files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wLMr
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
Pull security subsystem updates from James Morris:
"Highlights:
- TPM core and driver updates/fixes
- IPv6 security labeling (CALIPSO)
- Lots of Apparmor fixes
- Seccomp: remove 2-phase API, close hole where ptrace can change
syscall #"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (156 commits)
apparmor: fix SECURITY_APPARMOR_HASH_DEFAULT parameter handling
tpm: Add TPM 2.0 support to the Nuvoton i2c driver (NPCT6xx family)
tpm: Factor out common startup code
tpm: use devm_add_action_or_reset
tpm2_i2c_nuvoton: add irq validity check
tpm: read burstcount from TPM_STS in one 32-bit transaction
tpm: fix byte-order for the value read by tpm2_get_tpm_pt
tpm_tis_core: convert max timeouts from msec to jiffies
apparmor: fix arg_size computation for when setprocattr is null terminated
apparmor: fix oops, validate buffer size in apparmor_setprocattr()
apparmor: do not expose kernel stack
apparmor: fix module parameters can be changed after policy is locked
apparmor: fix oops in profile_unpack() when policy_db is not present
apparmor: don't check for vmalloc_addr if kvzalloc() failed
apparmor: add missing id bounds check on dfa verification
apparmor: allow SYS_CAP_RESOURCE to be sufficient to prlimit another task
apparmor: use list_next_entry instead of list_entry_next
apparmor: fix refcount race when finding a child profile
apparmor: fix ref count leak when profile sha1 hash is read
apparmor: check that xindex is in trans_table bounds
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
The linker routines that we rely on to produce a relocatable PIE binary
treat it as a shared ELF object in some ways, i.e., it emits symbol based
R_AARCH64_ABS64 relocations into the final binary since doing so would be
appropriate when linking a shared library that is subject to symbol
preemption. (This means that an executable can override certain symbols
that are exported by a shared library it is linked with, and that the
shared library *must* update all its internal references as well, and point
them to the version provided by the executable.)
Symbol preemption does not occur for OS hosted PIE executables, let alone
for vmlinux, and so we would prefer to get rid of these symbol based
relocations. This would allow us to simplify the relocation routines, and
to strip the .dynsym, .dynstr and .hash sections from the binary. (Note
that these are tiny, and are placed in the .init segment, but they clutter
up the vmlinux binary.)
Note that these R_AARCH64_ABS64 relocations are only emitted for absolute
references to symbols defined in the linker script, all other relocatable
quantities are covered by anonymous R_AARCH64_RELATIVE relocations that
simply list the offsets to all 64-bit values in the binary that need to be
fixed up based on the offset between the link time and run time addresses.
Fortunately, GNU ld has a -Bsymbolic option, which is intended for shared
libraries to allow them to ignore symbol preemption, and unconditionally
bind all internal symbol references to its own definitions. So set it for
our PIE binary as well, and get rid of the asoociated sections and the
relocation code that processes them.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: fixed conflict with __dynsym_offset linker script entry]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Due to the untyped KIMAGE_VADDR constant, the linker may not notice
that the __rela_offset and __dynsym_offset expressions are absolute
values (i.e., are not subject to relocation). This does not matter for
KASLR, but it does confuse kallsyms in relative mode, since it uses
the lowest non-absolute symbol address as the anchor point, and expects
all other symbol addresses to be within 4 GB of it.
Fix this by qualifying these expressions as ABSOLUTE() explicitly.
Fixes: 0cd3defe0a ("arm64: kernel: perform relocation processing from ID map")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
- ACPI support for guests on ARM platforms.
- Generic steal time support for arm and x86.
- Support cases where kernel cpu is not Xen VCPU number (e.g., if
in-guest kexec is used).
- Use the system workqueue instead of a custom workqueue in various
places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXmLlrAAoJEFxbo/MsZsTRvRQH/1wOMF8BmlbZfR7H3qwDfjst
ApNifCiZE08xDtWBlwUaBFAQxyflQS9BBiNZDVK0sysIdXeOdpWV7V0ZjRoLL+xr
czsaaGXDcmXxJxApoMDVuT7FeP6rEk6LVAYRoHpVjJjMZGW3BbX1vZaMW4DXl2WM
9YNaF2Lj+rpc1f8iG31nUxwkpmcXFog6ct4tu7HiyCFT3hDkHt/a4ghuBdQItCkd
vqBa1pTpcGtQBhSmWzlylN/PV2+NKcRd+kGiwd09/O/rNzogTMCTTWeHKAtMpPYb
Cu6oSqJtlK5o0vtr0qyLSWEGIoyjE2gE92s0wN3iCzFY1PldqdsxUO622nIj+6o=
=G6q3
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Features and fixes for 4.8-rc0:
- ACPI support for guests on ARM platforms.
- Generic steal time support for arm and x86.
- Support cases where kernel cpu is not Xen VCPU number (e.g., if
in-guest kexec is used).
- Use the system workqueue instead of a custom workqueue in various
places"
* tag 'for-linus-4.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (47 commits)
xen: add static initialization of steal_clock op to xen_time_ops
xen/pvhvm: run xen_vcpu_setup() for the boot CPU
xen/evtchn: use xen_vcpu_id mapping
xen/events: fifo: use xen_vcpu_id mapping
xen/events: use xen_vcpu_id mapping in events_base
x86/xen: use xen_vcpu_id mapping when pointing vcpu_info to shared_info
x86/xen: use xen_vcpu_id mapping for HYPERVISOR_vcpu_op
xen: introduce xen_vcpu_id mapping
x86/acpi: store ACPI ids from MADT for future usage
x86/xen: update cpuid.h from Xen-4.7
xen/evtchn: add IOCTL_EVTCHN_RESTRICT
xen-blkback: really don't leak mode property
xen-blkback: constify instance of "struct attribute_group"
xen-blkfront: prefer xenbus_scanf() over xenbus_gather()
xen-blkback: prefer xenbus_scanf() over xenbus_gather()
xen: support runqueue steal time on xen
arm/xen: add support for vm_assist hypercall
xen: update xen headers
xen-pciback: drop superfluous variables
xen-pciback: short-circuit read path used for merging write values
...
- Kexec support for arm64
- Kprobes support
- Expose MIDR_EL1 and REVIDR_EL1 CPU identification registers to sysfs
- Trapping of user space cache maintenance operations and emulation in
the kernel (CPU errata workaround)
- Clean-up of the early page tables creation (kernel linear mapping, EFI
run-time maps) to avoid splitting larger blocks (e.g. pmds) into
smaller ones (e.g. ptes)
- VDSO support for CLOCK_MONOTONIC_RAW in clock_gettime()
- ARCH_HAS_KCOV enabled for arm64
- Optimise IP checksum helpers
- SWIOTLB optimisation to only allocate/initialise the buffer if the
available RAM is beyond the 32-bit mask
- Properly handle the "nosmp" command line argument
- Fix for the initialisation of the CPU debug state during early boot
- vdso-offsets.h build dependency workaround
- Build fix when RANDOMIZE_BASE is enabled with MODULES off
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iJOY
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- Kexec support for arm64
- Kprobes support
- Expose MIDR_EL1 and REVIDR_EL1 CPU identification registers to sysfs
- Trapping of user space cache maintenance operations and emulation in
the kernel (CPU errata workaround)
- Clean-up of the early page tables creation (kernel linear mapping,
EFI run-time maps) to avoid splitting larger blocks (e.g. pmds) into
smaller ones (e.g. ptes)
- VDSO support for CLOCK_MONOTONIC_RAW in clock_gettime()
- ARCH_HAS_KCOV enabled for arm64
- Optimise IP checksum helpers
- SWIOTLB optimisation to only allocate/initialise the buffer if the
available RAM is beyond the 32-bit mask
- Properly handle the "nosmp" command line argument
- Fix for the initialisation of the CPU debug state during early boot
- vdso-offsets.h build dependency workaround
- Build fix when RANDOMIZE_BASE is enabled with MODULES off
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (64 commits)
arm64: arm: Fix-up the removal of the arm64 regs_query_register_name() prototype
arm64: Only select ARM64_MODULE_PLTS if MODULES=y
arm64: mm: run pgtable_page_ctor() on non-swapper translation table pages
arm64: mm: make create_mapping_late() non-allocating
arm64: Honor nosmp kernel command line option
arm64: Fix incorrect per-cpu usage for boot CPU
arm64: kprobes: Add KASAN instrumentation around stack accesses
arm64: kprobes: Cleanup jprobe_return
arm64: kprobes: Fix overflow when saving stack
arm64: kprobes: WARN if attempting to step with PSTATE.D=1
arm64: debug: remove unused local_dbg_{enable, disable} macros
arm64: debug: remove redundant spsr manipulation
arm64: debug: unmask PSTATE.D earlier
arm64: localise Image objcopy flags
arm64: ptrace: remove extra define for CPSR's E bit
kprobes: Add arm64 case in kprobe example module
arm64: Add kernel return probes support (kretprobes)
arm64: Add trampoline code for kretprobes
arm64: kprobes instruction simulation support
arm64: Treat all entry code as non-kprobe-able
...
* acpi-processor:
ACPI: enable ACPI_PROCESSOR_IDLE on ARM64
arm64: add support for ACPI Low Power Idle(LPI)
drivers: firmware: psci: initialise idle states using ACPI LPI
cpuidle: introduce CPU_PM_CPU_IDLE_ENTER macro for ARM{32, 64}
arm64: cpuidle: drop __init section marker to arm_cpuidle_init
ACPI / processor_idle: Add support for Low Power Idle(LPI) states
ACPI / processor_idle: introduce ACPI_PROCESSOR_CSTATE
* acpi-cppc:
mailbox: pcc: Add PCC request and free channel declarations
ACPI / CPPC: Prevent cpc_desc_ptr points to the invalid data
ACPI: CPPC: Return error if _CPC is invalid on a CPU
* acpi-apei:
ACPI / APEI: Add Boot Error Record Table (BERT) support
ACPI / einj: Make error paths more talkative
ACPI / einj: Convert EINJ_PFX to proper pr_fmt
* acpi-sleep:
ACPI: Execute _PTS before system reboot
* acpi-tables:
ACPI: Rename configfs.c to acpi_configfs.c to prevent link error
ACPI: add support for loading SSDTs via configfs
ACPI: add support for configfs
efi / ACPI: load SSTDs from EFI variables
spi / ACPI: add support for ACPI reconfigure notifications
i2c / ACPI: add support for ACPI reconfigure notifications
ACPI: add support for ACPI reconfiguration notifiers
ACPI / scan: fix enumeration (visited) flags for bus rescans
ACPI / documentation: add SSDT overlays documentation
ACPI: ARM64: support for ACPI_TABLE_UPGRADE
ACPI / tables: introduce ARCH_HAS_ACPI_TABLE_UPGRADE
ACPI / tables: move arch-specific symbol to asm/acpi.h
ACPI / tables: table upgrade: refactor function definitions
ACPI / tables: table upgrade: use cacheable map for tables
Conflicts:
arch/arm64/include/asm/acpi.h
This patch adds appropriate callbacks to support ACPI Low Power Idle
(LPI) on ARM64.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit ea389daa7f (arm64: cpuidle: add __init section marker to
arm_cpuidle_init) added the __init annotation to arm_cpuidle_init
as it was not needed after booting which was correct at that time.
However with the introduction of ACPI LPI support, this will be used
from cpuhotplug path in ACPI processor driver.
This patch drops the __init annotation from arm_cpuidle_init to avoid
the following warning:
WARNING: vmlinux.o(.text+0x113c8): Section mismatch in reference from the
function acpi_processor_ffh_lpi_probe() to the function
.init.text:arm_cpuidle_init()
The function acpi_processor_ffh_lpi_probe() references
the function __init arm_cpuidle_init().
This is often because acpi_processor_ffh_lpi_probe() lacks a __init
annotation or the annotation of arm_cpuidle_init is wrong.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* kprobes:
arm64: kprobes: Add KASAN instrumentation around stack accesses
arm64: kprobes: Cleanup jprobe_return
arm64: kprobes: Fix overflow when saving stack
arm64: kprobes: WARN if attempting to step with PSTATE.D=1
kprobes: Add arm64 case in kprobe example module
arm64: Add kernel return probes support (kretprobes)
arm64: Add trampoline code for kretprobes
arm64: kprobes instruction simulation support
arm64: Treat all entry code as non-kprobe-able
arm64: Blacklist non-kprobe-able symbol
arm64: Kprobes with single stepping support
arm64: add conditional instruction simulation support
arm64: Add more test functions to insn.c
arm64: Add HAVE_REGS_AND_STACK_ACCESS_API feature
Passing "nosmp" should boot the kernel with a single processor, without
provision to enable secondary CPUs even if they are present. "nosmp" is
implemented by setting maxcpus=0. At the moment we still mark the secondary
CPUs present even with nosmp, which allows the userspace to bring them
up. This patch corrects the smp_prepare_cpus() to honor the maxcpus == 0.
Commit 44dbcc93ab ("arm64: Fix behavior of maxcpus=N") fixed the
behavior for maxcpus >= 1, but broke maxcpus = 0.
Fixes: 44dbcc93ab ("arm64: Fix behavior of maxcpus=N")
Cc: <stable@vger.kernel.org> # 4.7+
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
[catalin.marinas@arm.com: updated code comment]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In smp_prepare_boot_cpu(), we invoke cpuinfo_store_boot_cpu to store
the cpuinfo in a per-cpu ptr, before initialising the per-cpu offset for
the boot CPU. This patch reorders the sequence to make sure we initialise
the per-cpu offset before accessing the per-cpu area.
Commit 4b998ff188 ("arm64: Delay cpuinfo_store_boot_cpu") fixed the
issue where we modified the per-cpu area even before the kernel initialises
the per-cpu areas, but failed to wait until the boot cpu updated it's
offset.
Fixes: 4b998ff188 ("arm64: Delay cpuinfo_store_boot_cpu")
Cc: <stable@vger.kernel.org> # 4.4+
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
jprobe_return seems to have aged badly. Comments referring to
non-existent behaviours, and a dangerous habit of messing
with registers without telling the compiler.
This patches applies the following remedies:
- Fix the comments to describe the actual behaviour
- Tidy up the asm sequence to directly assign the
stack pointer without clobbering extra registers
- Mark the rest of the function as unreachable() so
that the compiler knows that there is no need for
an epilogue
- Stop making jprobe_return_break a global function
(you really don't want to call that guy, and it isn't
even a function).
Tested with tcp_probe.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The MIN_STACK_SIZE macro tries evaluate how much stack space needs
to be saved in the jprobes_stack array, sized at 128 bytes.
When using the IRQ stack, said macro can happily return up to
IRQ_STACK_SIZE, which is 16kB. Mayhem follows.
This patch fixes things by getting rid of the crazy macro and
limiting the copy to be at most the size of the jprobes_stack
array, no matter which stack we're on.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Stepping with PSTATE.D=1 is bad news. The step won't generate a debug
exception and we'll likely walk off into random data structures. This
should never happen, but when it does, it's a PITA to debug. Add a
WARN_ON to shout if we realise this is about to take place.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is no need to explicitly clear the SS bit immediately before
setting it unconditionally.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Clearing PSTATE.D is one of the requirements for generating a debug
exception. The arm64 booting protocol requires that PSTATE.D is set,
since many of the debug registers (for example, the hw_breakpoint
registers) are UNKNOWN out of reset and could potentially generate
spurious, fatal debug exceptions in early boot code if PSTATE.D was
clear. Once the debug registers have been safely initialised, PSTATE.D
is cleared, however this is currently broken for two reasons:
(1) The boot CPU clears PSTATE.D in a postcore_initcall and secondary
CPUs clear PSTATE.D in secondary_start_kernel. Since the initcall
runs after SMP (and the scheduler) have been initialised, there is
no guarantee that it is actually running on the boot CPU. In this
case, the boot CPU is left with PSTATE.D set and is not capable of
generating debug exceptions.
(2) In a preemptible kernel, we may explicitly schedule on the IRQ
return path to EL1. If an IRQ occurs with PSTATE.D set in the idle
thread, then we may schedule the kthread_init thread, run the
postcore_initcall to clear PSTATE.D and then context switch back
to the idle thread before returning from the IRQ. The exception
return path will then restore PSTATE.D from the stack, and set it
again.
This patch fixes the problem by moving the clearing of PSTATE.D earlier
to proc.S. This has the desirable effect of clearing it in one place for
all CPUs, long before we have to worry about the scheduler or any
exception handling. We ensure that the previous reset of MDSCR_EL1 has
completed before unmasking the exception, so that any spurious
exceptions resulting from UNKNOWN debug registers are not generated.
Without this patch applied, the kprobes selftests have been seen to fail
under KVM, where we end up attempting to step the OOL instruction buffer
with PSTATE.D set and therefore fail to complete the step.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The pre-handler of this special 'trampoline' kprobe executes the return
probe handler functions and restores original return address in ELR_EL1.
This way the saved pt_regs still hold the original register context to be
carried back to the probed kernel function.
Signed-off-by: Sandeepa Prabhu <sandeepa.s.prabhu@gmail.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The trampoline code is used by kretprobes to capture a return from a probed
function. This is done by saving the registers, calling the handler, and
restoring the registers. The code then returns to the original saved caller
return address. It is necessary to do this directly instead of using a
software breakpoint because the code used in processing that breakpoint
could itself be kprobe'd and cause a problematic reentry into the debug
exception handler.
Signed-off-by: William Cohen <wcohen@redhat.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
[catalin.marinas@arm.com: removed unnecessary masking of the PSTATE bits]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Kprobes needs simulation of instructions that cannot be stepped
from a different memory location, e.g.: those instructions
that uses PC-relative addressing. In simulation, the behaviour
of the instruction is implemented using a copy of pt_regs.
The following instruction categories are simulated:
- All branching instructions(conditional, register, and immediate)
- Literal access instructions(load-literal, adr/adrp)
Conditional execution is limited to branching instructions in
ARM v8. If conditions at PSTATE do not match the condition fields
of opcode, the instruction is effectively NOP.
Thanks to Will Cohen for assorted suggested changes.
Signed-off-by: Sandeepa Prabhu <sandeepa.s.prabhu@gmail.com>
Signed-off-by: William Cohen <wcohen@redhat.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
[catalin.marinas@arm.com: removed linux/module.h include]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Entry symbols are not kprobe safe. So blacklist them for kprobing.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
[catalin.marinas@arm.com: Do not include syscall wrappers in .entry.text]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add all function symbols which are called from do_debug_exception under
NOKPROBE_SYMBOL, as they can not kprobed.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add support for basic kernel probes(kprobes) and jump probes
(jprobes) for ARM64.
Kprobes utilizes software breakpoint and single step debug
exceptions supported on ARM v8.
A software breakpoint is placed at the probe address to trap the
kernel execution into the kprobe handler.
ARM v8 supports enabling single stepping before the break exception
return (ERET), with next PC in exception return address (ELR_EL1). The
kprobe handler prepares an executable memory slot for out-of-line
execution with a copy of the original instruction being probed, and
enables single stepping. The PC is set to the out-of-line slot address
before the ERET. With this scheme, the instruction is executed with the
exact same register context except for the PC (and DAIF) registers.
Debug mask (PSTATE.D) is enabled only when single stepping a recursive
kprobe, e.g.: during kprobes reenter so that probed instruction can be
single stepped within the kprobe handler -exception- context.
The recursion depth of kprobe is always 2, i.e. upon probe re-entry,
any further re-entry is prevented by not calling handlers and the case
counted as a missed kprobe).
Single stepping from the x-o-l slot has a drawback for PC-relative accesses
like branching and symbolic literals access as the offset from the new PC
(slot address) may not be ensured to fit in the immediate value of
the opcode. Such instructions need simulation, so reject
probing them.
Instructions generating exceptions or cpu mode change are rejected
for probing.
Exclusive load/store instructions are rejected too. Additionally, the
code is checked to see if it is inside an exclusive load/store sequence
(code from Pratyush).
System instructions are mostly enabled for stepping, except MSR/MRS
accesses to "DAIF" flags in PSTATE, which are not safe for
probing.
This also changes arch/arm64/include/asm/ptrace.h to use
include/asm-generic/ptrace.h.
Thanks to Steve Capper and Pratyush Anand for several suggested
Changes.
Signed-off-by: Sandeepa Prabhu <sandeepa.s.prabhu@gmail.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cease using the arm32 arm_check_condition() function and replace it with
a local version for use in deprecated instruction support on arm64. Also
make the function table used by this available for future use by kprobes
and/or uprobes.
This function is derived from code written by Sandeepa Prabhu.
Signed-off-by: Sandeepa Prabhu <sandeepa.s.prabhu@gmail.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Certain instructions are hard to execute correctly out-of-line (as in
kprobes). Test functions are added to insn.[hc] to identify these. The
instructions include any that use PC-relative addressing, change the PC,
or change interrupt masking. For efficiency and simplicity test
functions are also added for small collections of related instructions.
Signed-off-by: David A. Long <dave.long@linaro.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add HAVE_REGS_AND_STACK_ACCESS_API feature for arm64, including supporting
functions and defines.
Signed-off-by: David A. Long <dave.long@linaro.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
[catalin.marinas@arm.com: Remove unused functions]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
It can be useful for JIT software to be aware of MIDR_EL1 and
REVIDR_EL1 to ascertain the presence of any core errata that could
affect code generation.
This patch exposes these registers through sysfs:
/sys/devices/system/cpu/cpu$ID/regs/identification/midr_el1
/sys/devices/system/cpu/cpu$ID/regs/identification/revidr_el1
where $ID is the cpu number. For big.LITTLE systems, one can have a
mixture of cores (e.g. Cortex A53 and Cortex A57), thus all CPUs need
to be enumerated.
If the kernel does not have valid information to populate these entries
with, an empty string is returned to userspace.
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Steve Capper <steve.capper@linaro.org>
[suzuki.poulose@arm.com: ABI documentation updates, hotplug notifiers, kobject changes]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
So far the arm64 clock_gettime() vDSO implementation only supported
the following clocks, falling back to the syscall for the others:
- CLOCK_REALTIME{,_COARSE}
- CLOCK_MONOTONIC{,_COARSE}
This patch adds support for the CLOCK_MONOTONIC_RAW clock, taking
advantage of the recent refactoring of the vDSO time functions. Like
the non-_COARSE clocks, this only works when the "arch_sys_counter"
clocksource is in use (allowing us to read the current time from the
virtual counter register), otherwise we also have to fall back to the
syscall.
Most of the data is shared with CLOCK_MONOTONIC, and the algorithm is
similar. The reference implementation in kernel/time/timekeeping.c
shows that:
- CLOCK_MONOTONIC = tk->wall_to_monotonic + tk->xtime_sec +
timekeeping_get_ns(&tk->tkr_mono)
- CLOCK_MONOTONIC_RAW = tk->raw_time + timekeeping_get_ns(&tk->tkr_raw)
- tkr_mono and tkr_raw are identical (in particular, same
clocksource), except these members:
* mult (only mono's multiplier is NTP-adjusted)
* xtime_nsec (always 0 for raw)
Therefore, tk->raw_time and tkr_raw->mult are now also stored in the
vDSO data page.
Cc: Ali Saidi <ali.saidi@arm.com>
Signed-off-by: Kevin Brodsky <kevin.brodsky@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Time functions are directly implemented in assembly in arm64, and it
is desirable to keep it this way for performance reasons (everything
fits in registers, so that the stack is not used at all). However, the
current implementation is quite difficult to read and understand (even
considering it's assembly). Additionally, due to the structure of
__kernel_clock_gettime, which heavily uses conditional branches to
share code between the different clocks, it is difficult to support a
new clock without making the branches even harder to follow.
This commit completely refactors the structure of clock_gettime (and
gettimeofday along the way) while keeping exactly the same algorithms.
We no longer try to share code; instead, macros provide common
operations. This new approach comes with a number of advantages:
- In clock_gettime, clock implementations are no longer interspersed,
making them much more readable. Additionally, macros only use
registers passed as arguments or reserved with .req, this way it is
easy to make sure that registers are properly allocated. To avoid a
large number of branches in a given execution path, a jump table is
used; a normal execution uses 3 unconditional branches.
- __do_get_tspec has been replaced with 2 macros (get_ts_clock_mono,
get_clock_shifted_nsec) and explicit loading of data from the vDSO
page. Consequently, clock_gettime and gettimeofday are now leaf
functions, and saving x30 (lr) is no longer necessary.
- Variables protected by tb_seq_count are now loaded all at once,
allowing to merge the seqcnt_read macro into seqcnt_check.
- For CLOCK_REALTIME_COARSE, removed an unused load of the wall to
monotonic timespec.
- For CLOCK_MONOTONIC_COARSE, removed a few shift instructions.
Obviously, the downside of sharing less code is an increase in code
size. However since the vDSO has its own code page, this does not
really matter, as long as the size of the DSO remains below 4 kB. For
now this should be all right:
Before After
vdso.so size (B) 2776 3000
Signed-off-by: Kevin Brodsky <kevin.brodsky@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
arm64/kernel/{vdso,signal}.c include vdso-offsets.h, as well as any
file that includes asm/vdso.h. Therefore, vdso-offsets.h must be
generated before these files are compiled.
The current rules in arm64/kernel/Makefile do not actually enforce
this, because even though $(obj)/vdso is listed as a prerequisite for
vdso-offsets.h, this does not result in the intended effect of
building the vdso subdirectory (before all the other objects). As a
consequence, depending on the order in which the rules are followed,
vdso-offsets.h is updated or not before arm64/kernel/{vdso,signal}.o
are built. The current rules also impose an unnecessary dependency on
vdso-offsets.h for all arm64/kernel/*.o, resulting in unnecessary
rebuilds. This is made obvious when using make -j:
touch arch/arm64/kernel/vdso/gettimeofday.S && make -j$NCPUS arch/arm64/kernel
will sometimes result in none of arm64/kernel/*.o being
rebuilt, sometimes all of them, or even just some of them.
It is quite difficult to ensure that a header is generated before it
is used with recursive Makefiles by using normal rules. Instead,
arch-specific generated headers are normally built in the archprepare
recipe in the arch Makefile (see for instance arch/ia64/Makefile).
Unfortunately, asm-offsets.h is included in gettimeofday.S, and must
therefore be generated before vdso-offsets.h, which is not the case if
archprepare is used. For this reason, a rule run after archprepare has
to be used.
This commit adds rules in arm64/Makefile to build vdso-offsets.h
during the prepare step, ensuring that vdso-offsets.h is generated
before building anything. It also removes the now-unnecessary
dependencies on vdso-offsets.h in arm64/kernel/Makefile. Finally, it
removes the duplication of asm-offsets.h between arm64/kernel/vdso/
and include/generated/ and makes include/generated/vdso-offsets.h a
target in arm64/kernel/vdso/Makefile.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Michal Marek <mmarek@suse.com>
Signed-off-by: Kevin Brodsky <kevin.brodsky@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This reverts commit 90f777beb7.
While this commit was aimed at fixing the dependencies, with a large
make -j the vdso-offsets.h file is not generated, leading to build
failures.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
arch/arm64/kernel/{vdso,signal}.c include generated/vdso-offsets.h, and
therefore the symbol offsets must be generated before these files are
compiled.
The current rules in arm64/kernel/Makefile do not actually enforce
this, because even though $(obj)/vdso is listed as a prerequisite for
vdso-offsets.h, this does not result in the intended effect of
building the vdso subdirectory (before all the other objects). As a
consequence, depending on the order in which the rules are followed,
vdso-offsets.h is updated or not before arm64/kernel/{vdso,signal}.o
are built. The current rules also impose an unnecessary dependency on
vdso-offsets.h for all arm64/kernel/*.o, resulting in unnecessary
rebuilds.
This patch removes the arch/arm64/kernel/vdso/vdso-offsets.h file
generation, leaving only the include/generated/vdso-offsets.h one. It
adds a forced dependency check of the vdso-offsets.h file in
arch/arm64/kernel/Makefile which, if not up to date according to the
arch/arm64/kernel/vdso/Makefile rules (depending on vdso.so.dbg), will
trigger the vdso/ subdirectory build and vdso-offsets.h re-generation.
Automatic kbuild dependency rules between kernel/{vdso,signal}.c rules
and vdso-offsets.h will guarantee that the vDSO object is built first,
followed by the generated symbol offsets header file.
Reported-by: Kevin Brodsky <kevin.brodsky@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cavium erratum 27456 commit 104a0c02e8
("arm64: Add workaround for Cavium erratum 27456")
is applicable for thunderx-81xx pass1.0 SoC as well.
Adding code to enable to 81xx.
Signed-off-by: Ganapatrao Kulkarni <gkulkarni@cavium.com>
Reviewed-by: Andrew Pinski <apinski@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If we take an exception while at EL1, the exception handler inherits
the original context's addr_limit and PSTATE.UAO values. To be consistent
always reset addr_limit and PSTATE.UAO on (re-)entry to EL1. This
prevents accidental re-use of the original context's addr_limit.
Based on a similar patch for arm from Russell King.
Cc: <stable@vger.kernel.org> # 4.6-
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Move xen_early_init() before efi_init(), then when calling efi_init()
could initialize Xen specific UEFI.
Check if it runs on Xen hypervisor through the flat dts.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Add the code that enables the switch to the lower HYP VA range.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
When running the OS with a page size > 4 KB, we need to round up mappings
for regions that are not aligned to the OS's page size. We already avoid
block mappings for EfiRuntimeServicesCode/Data regions for other reasons,
but in the unlikely event that other unaliged regions exists that have the
EFI_MEMORY_RUNTIME attribute set, ensure that unaligned regions are always
mapped down to pages. This way, the overlapping page is guaranteed not to
be covered by a block mapping that needs to be split.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
To avoid triggering diagnostics in the MMU code that are finicky about
splitting block mappings into more granular mappings, ensure that regions
that are likely to appear in the Memory Attributes table as well as the
UEFI memory map are always mapped down to pages. This way, we can use
apply_to_page_range() instead of create_pgd_mapping() for the second pass,
which cannot split or merge block entries, and operates strictly on PTEs.
Note that this aligns the arm64 Memory Attributes table handling code with
the ARM code, which already uses apply_to_page_range() to set the strict
permissions.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add a bool parameter 'allow_block_mappings' to create_pgd_mapping() and
the various helper functions that it descends into, to give the caller
control over whether block entries may be used to create the mapping.
The UEFI runtime mapping routines will use this to avoid creating block
entries that would need to split up into page entries when applying the
permissions listed in the Memory Attributes firmware table.
This also replaces the block_mappings_allowed() helper function that was
added for DEBUG_PAGEALLOC functionality, but the resulting code is
functionally equivalent (given that debug_page_alloc does not operate on
EFI page table entries anyway)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The ARM errata 819472, 826319, 827319 and 824069 for affected
Cortex-A53 cores demand to promote "dc cvau" instructions to
"dc civac". Since we allow userspace to also emit those instructions,
we should make sure that "dc cvau" gets promoted there too.
So lets grasp the nettle here and actually trap every userland cache
maintenance instruction once we detect at least one affected core in
the system.
We then emulate the instruction by executing it on behalf of userland,
promoting "dc cvau" to "dc civac" on the way and injecting access
fault back into userspace.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[catalin.marinas@arm.com: s/set_segfault/arm64_notify_segfault/]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The code for injecting a signal into userland if a trapped instruction
fails emulation due to a _userland_ error (like an illegal address)
will be used more often with the next patch.
Factor out the core functionality into a separate function and use
that both for the existing trap handler and for the deprecated
instructions emulation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[catalin.marinas@arm.com: s/set_segfault/arm64_notify_segfault/]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently we call the (optional) enable function for CPU _features_
only. As CPU _errata_ descriptions share the same data structure and
having an enable function is useful for errata as well (for instance
to set bits in SCTLR), lets call it when enumerating erratas too.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As Kees Cook notes in the ARM counterpart of this patch [0]:
The _etext position is defined to be the end of the kernel text code,
and should not include any part of the data segments. This interferes
with things that might check memory ranges and expect executable code
up to _etext.
In particular, Kees is referring to the HARDENED_USERCOPY patch set [1],
which rejects attempts to call copy_to_user() on kernel ranges containing
executable code, but does allow access to the .rodata segment. Regardless
of whether one may or may not agree with the distinction, it makes sense
for _etext to have the same meaning across architectures.
So let's put _etext where it belongs, between .text and .rodata, and fix
up existing references to use __init_begin instead, which unlike _end_rodata
includes the exception and notes sections as well.
The _etext references in kaslr.c are left untouched, since its references
to [_stext, _etext) are meant to capture potential jump instruction targets,
and so disregarding .rodata is actually an improvement here.
[0] http://article.gmane.org/gmane.linux.kernel/2245084
[1] http://thread.gmane.org/gmane.linux.kernel.hardened.devel/2502
Reported-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
To aid in debugging kexec problems or when adding new functionality to
kexec add a new routine kexec_image_info() and several inline pr_debug
statements.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add three new files, kexec.h, machine_kexec.c and relocate_kernel.S to the
arm64 architecture that add support for the kexec re-boot mechanism
(CONFIG_KEXEC) on arm64 platforms.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Reviewed-by: James Morse <james.morse@arm.com>
[catalin.marinas@arm.com: removed dead code following James Morse's comments]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 68234df4ea ("arm64: kill flush_cache_all()") removed the global
arm64 routines cpu_reset() and cpu_soft_restart() needed by the arm64
kexec and kdump support. Add back a simplified version of
cpu_soft_restart() with some changes needed for kexec in the new files
cpu_reset.S, and cpu_reset.h.
When a CPU is reset it needs to be put into the exception level it had when
it entered the kernel. Update cpu_soft_restart() to accept an argument
which signals if the reset address should be entered at EL1 or EL2, and
add a new hypercall HVC_SOFT_RESTART which is used for the EL2 switch.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
kernel/smp.c has a fancy counter that keeps track of the number of CPUs
it marked as not-present and left in cpu_park_loop(). If there are any
CPUs spinning in here, features like kexec or hibernate may release them
by overwriting this memory.
This problem also occurs on machines using spin-tables to release
secondary cores.
After commit 44dbcc93ab ("arm64: Fix behavior of maxcpus=N")
we bring all known cpus into the secondary holding pen, meaning this
memory can't be re-used by kexec or hibernate.
Add a function cpus_are_stuck_in_kernel() to determine if either of these
cases have occurred.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[catalin.marinas@arm.com: cherry-picked from mainline for kexec dependency]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On systems with PCI_PROBE_ONLY set, we rely on BAR assignments from
firmware. Previously we did not insert those resources into the resource
tree, so we had to skip pci_enable_resources() because it fails if
resources are not in the resource tree.
Now that we *do* insert resources even when PCI_PROBE_ONLY is set, we no
longer need the ARM64-specific pcibios_enable_device(). Remove it so we
use the generic version.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Catalin Marinas <catalin.marinas@arm.com>
After patch "of/platform: Add common method to populate default bus",
it is possible for arch code to remove unnecessary callers of
of_platform_populate with default match table.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The of_iommu_init() is called multiple times by arch code,
make it postcore_initcall_sync, then we can drop relevant
calls fully.
Note, the IOMMUs should have a chance to perform some basic
initialisation before we start adding masters to them. So
postcore_initcall_sync is good choice, it ensures of_iommu_init()
called before of_platform_populate.
Acked-by: Rich Felker <dalias@libc.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Hibernate relies on cpu hotplug to prevent secondary cores executing
the kernel text while it is being restored.
Add a call to cpus_are_stuck_in_kernel() to determine if there are
CPUs not counted by 'num_online_cpus()', and prevent hibernate in this
case.
Fixes: 82869ac57b ("arm64: kernel: Add support for hibernate/suspend-to-disk")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
kernel/smp.c has a fancy counter that keeps track of the number of CPUs
it marked as not-present and left in cpu_park_loop(). If there are any
CPUs spinning in here, features like kexec or hibernate may release them
by overwriting this memory.
This problem also occurs on machines using spin-tables to release
secondary cores.
After commit 44dbcc93ab ("arm64: Fix behavior of maxcpus=N")
we bring all known cpus into the secondary holding pen, meaning this
memory can't be re-used by kexec or hibernate.
Add a function cpus_are_stuck_in_kernel() to determine if either of these
cases have occurred.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds support for ACPI_TABLE_UPGRADE for ARM64
To access initrd image we need to move initialization
of linear mapping a bit earlier.
The implementation of the feature acpi_table_upgrade()
(drivers/acpi/tables.c) works with initrd data represented as an array
in virtual memory. It uses some library utility to find the redefined
tables in that array and iterates over it to copy the data to new
allocated memory. So to access the initrd data via fixmap
we need to rewrite it considerably.
In x86 arch, kernel memory is already mapped by the time when
acpi_table_upgrade() and acpi_boot_table_init() are called so I
think that we can just move this mapping one function earlier too.
Signed-off-by: Jon Masters <jcm@redhat.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently we treat ESR_EL1 bit 24 as software-defined for distinguishing
instruction aborts from data aborts, but this bit is architecturally
RES0 for instruction aborts, and could be allocated for an arbitrary
purpose in future. Additionally, we hard-code the value in entry.S
without the mnemonic, making the code difficult to understand.
Instead, remove ESR_LNX_EXEC, and distinguish aborts based on the esr,
which we already pass to the sole use of ESR_LNX_EXEC. A new helper,
is_el0_instruction_abort() is added to make the logic clear. Any
instruction aborts taken from EL1 will already have been handled by
bad_mode, so we need not handle that case in the helper.
For consistency, the existing permission_fault helper is renamed to
is_permission_fault, and the return type is changed to bool. There
should be no functional changes as the return value was a boolean
expression, and the result is only used in another boolean expression.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Dave P Martin <dave.martin@arm.com>
Cc: Huang Shijie <shijie.huang@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Several places open-code extraction of the EC field from an ESR_ELx
value, in subtly different ways. This is unfortunate duplication and
variation, and the precise logic used to extract the field is a
distraction.
This patch adds a new macro, ESR_ELx_EC(), to extract the EC field from
an ESR_ELx value in a consistent fashion.
Existing open-coded extractions in core arm64 code are moved over to the
new helper. KVM code is left as-is for the moment.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Huang Shijie <shijie.huang@arm.com>
Cc: Dave P Martin <dave.martin@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently dump_mem attempts to dump memory in 64-bit chunks when
reporting a failure in 64-bit code, or 32-bit chunks when reporting a
failure in 32-bit code. We added code to handle these two cases
separately in commit e147ae6d7f ("arm64: modify the dump mem for
64 bit addresses").
However, in all cases dump_mem is called, the failing context is a
kernel rather than user context. Additionally dump_mem is assumed to
only be used for kernel contexts, as internally it switches to
KERNEL_DS, and its callers pass kernel stack bounds.
This patch removes the redundant 32-bit chunk logic and associated
compat parameter, largely reverting the aforementioned commit. For the
call in __die(), the check of in_interrupt() is removed also, as __die()
is only called in response to faults from the kernel's exception level,
and thus the !user_mode(regs) check is sufficient. Were this not the
case, the used of task_stack_page(tsk) to generate the stack bounds
would be erroneous.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The upstream commit 1771c6e1a5
("x86/kasan: instrument user memory access API") added KASAN instrument to
x86 user memory access API, so added such instrument to ARM64 too.
Define __copy_to/from_user in C in order to add kasan_check_read/write call,
rename assembly implementation to __arch_copy_to/from_user.
Tested by test_kasan module.
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Current versions of gdb do not interoperate cleanly with kgdb on arm64
systems because gdb and kgdb do not use the same register description.
This patch modifies kgdb to work with recent releases of gdb (>= 7.8.1).
Compatibility with gdb (after the patch is applied) is as follows:
gdb-7.6 and earlier Ok
gdb-7.7 series Works if user provides custom target description
gdb-7.8(.0) Works if user provides custom target description
gdb-7.8.1 and later Ok
When commit 44679a4f14 ("arm64: KGDB: Add step debugging support") was
introduced it was paired with a gdb patch that made an incompatible
change to the gdbserver protocol. This patch was eventually merged into
the gdb sources:
https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commit;h=a4d9ba85ec5597a6a556afe26b712e878374b9dd
The change to the protocol was mostly made to simplify big-endian support
inside the kernel gdb stub. Unfortunately the gdb project released
gdb-7.7.x and gdb-7.8.0 before the protocol incompatibility was identified
and reversed:
https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commit;h=bdc144174bcb11e808b4e73089b850cf9620a7ee
This leaves us in a position where kgdb still uses the no-longer-used
protocol; gdb-7.8.1, which restored the original behaviour, was
released on 2014-10-29.
I don't believe it is possible to detect/correct the protocol
incompatiblity which means the kernel must take a view about which
version of the gdb remote protocol is "correct". This patch takes the
view that the original/current version of the protocol is correct
and that version found in gdb-7.7.x and gdb-7.8.0 is anomalous.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Close the hole where ptrace can change a syscall out from under seccomp.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Currently, if arch code wants to supply seccomp_data directly to
seccomp (which is generally much faster than having seccomp do it
using the syscall_get_xyz() API), it has to use the two-phase
seccomp hooks. Add it to the easy hooks, too.
Cc: linux-arch@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
If the kernel is set to show unhandled signals, and a user task does not
handle a SIGILL as a result of an instruction abort, we will attempt to
log the offending instruction with dump_instr before killing the task.
We use dump_instr to log the encoding of the offending userspace
instruction. However, dump_instr is also used to dump instructions from
kernel space, and internally always switches to KERNEL_DS before dumping
the instruction with get_user. When both PAN and UAO are in use, reading
a user instruction via get_user while in KERNEL_DS will result in a
permission fault, which leads to an Oops.
As we have regs corresponding to the context of the original instruction
abort, we can inspect this and only flip to KERNEL_DS if the original
abort was taken from the kernel, avoiding this issue. At the same time,
remove the redundant (and incorrect) comments regarding the order
dump_mem and dump_instr are called in.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: <stable@vger.kernel.org> #4.6+
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Fixes: 57f4959bad ("arm64: kernel: Add support for User Access Override")
Signed-off-by: Will Deacon <will.deacon@arm.com>
Implement pci_acpi_scan_root() and other arch-specific calls so ARM64 can
use ACPI to setup and enumerate PCI buses.
Use memory-mapped configuration space information from either the ACPI
_CBA method or the MCFG table and the ECAM library and generic ECAM config
accessor ops.
Implement acpi_pci_bus_find_domain_nr() to retrieve the domain number from
the acpi_pci_root structure.
Implement pcibios_add_bus() and pcibios_remove_bus() to call
acpi_pci_add_bus() and acpi_pci_remove_bus() for ACPI slot management and
other configuration.
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
On ACPI systems, the PCI_Config OperationRegion allows AML to access PCI
configuration space. The ACPI CA AML interpreter uses performs config
space accesses with acpi_os_read_pci_configuration() and
acpi_os_write_pci_configuration(), which are OS-dependent functions
supplied by acpi/osl.c.
Implement the arch-specific raw_pci_read() and raw_pci_write() interfaces
used by acpi/osl.c for PCI_Config accesses.
N.B. PCI_Config accesses are not supported before PCI bus enumeration.
[bhelgaas: changelog]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
To enable PCI legacy IRQs on platforms booting with ACPI, arch code should
include ACPI-specific callbacks that parse and set-up the device IRQ
number, equivalent to the DT boot path. Owing to the current ACPI core scan
handlers implementation, ACPI PCI legacy IRQs bindings cannot be parsed at
device add time, since that would trigger ACPI scan handlers ordering
issues depending on how the ACPI tables are defined.
To solve this problem and consolidate FW PCI legacy IRQs parsing in one
single pcibios callback (pending final removal), this patch moves DT PCI
IRQ parsing to the pcibios_alloc_irq() callback (called by PCI core code at
driver probe time) and adds ACPI PCI legacy IRQs parsing to the same
callback too, so that FW PCI legacy IRQs parsing is confined in one single
arch callback that can be easily removed when code parsing PCI legacy IRQs
is consolidated and moved to core PCI code.
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Extend pci_bus_find_domain_nr() so it can find the domain from either:
- ACPI, via the new acpi_pci_bus_find_domain_nr() interface, or
- DT, via of_pci_bus_find_domain_nr()
Note that this is only used for CONFIG_PCI_DOMAINS_GENERIC=y, so it does
not affect x86 or ia64.
[bhelgaas: changelog]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If we take an exception we don't expect (e.g. SError), we report this in
the bad_mode handler with pr_crit. Depending on the configured log
level, we may or may not log additional information in functions called
subsequently. Notably, the messages in dump_stack (including the CPU
number) are printed with KERN_DEFAULT and may not appear.
Some exceptions have an IMPLEMENTATION DEFINED ESR_ELx.ISS encoding, and
knowing the CPU number is crucial to correctly decode them. To ensure
that this is always possible, we should log the CPU number along with
the ESR_ELx value, so we are not reliant on subsequent logs or
additional printk configuration options.
This patch logs the CPU number in bad_mode such that it is possible for
a developer to decode these exceptions, provided access to sufficient
documentation.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Al Grant <Al.Grant@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch brings the PER_LINUX32 /proc/cpuinfo format more in line with
the 32-bit ARM one by providing an additional line:
model name : ARMv8 Processor rev X (v8l)
Cc: <stable@vger.kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Introduce a new file to hold ACPI based NUMA information parsing from
SRAT and SLIT.
SRAT includes the CPU ACPI ID to Proximity Domain mappings and memory
ranges to Proximity Domain mapping. SLIT has the information of inter
node distances(relative number for access latency).
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Ganapatrao Kulkarni <gkulkarni@caviumnetworks.com>
[rrichter@cavium.com Reworked for numa v10 series ]
Signed-off-by: Robert Richter <rrichter@cavium.com>
[david.daney@cavium.com reorderd and combinded with other patches in
Hanjun Guo's original set, removed get_mpidr_in_madt() and use
acpi_map_madt_entry() instead.]
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Dennis Chen <dennis.chen@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull perf updates from Ingo Molnar:
"Mostly tooling and PMU driver fixes, but also a number of late updates
such as the reworking of the call-chain size limiting logic to make
call-graph recording more robust, plus tooling side changes for the
new 'backwards ring-buffer' extension to the perf ring-buffer"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
perf record: Read from backward ring buffer
perf record: Rename variable to make code clear
perf record: Prevent reading invalid data in record__mmap_read
perf evlist: Add API to pause/resume
perf trace: Use the ptr->name beautifier as default for "filename" args
perf trace: Use the fd->name beautifier as default for "fd" args
perf report: Add srcline_from/to branch sort keys
perf evsel: Record fd into perf_mmap
perf evsel: Add overwrite attribute and check write_backward
perf tools: Set buildid dir under symfs when --symfs is provided
perf trace: Only auto set call-graph to "dwarf" when syscalls are being traced
perf annotate: Sort list of recognised instructions
perf annotate: Fix identification of ARM blt and bls instructions
perf tools: Fix usage of max_stack sysctl
perf callchain: Stop validating callchains by the max_stack sysctl
perf trace: Fix exit_group() formatting
perf top: Use machine->kptr_restrict_warned
perf trace: Warn when trying to resolve kernel addresses with kptr_restrict=1
perf machine: Do not bail out if not managing to read ref reloc symbol
perf/x86/intel/p4: Trival indentation fix, remove space
...
most architectures are relying on mmap_sem for write in their
arch_setup_additional_pages. If the waiting task gets killed by the oom
killer it would block oom_reaper from asynchronous address space reclaim
and reduce the chances of timely OOM resolving. Wait for the lock in
the killable mode and return with EINTR if the task got killed while
waiting.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Andy Lutomirski <luto@amacapital.net> [x86 vdso]
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define HAVE_EXIT_THREAD for archs which want to do something in
exit_thread. For others, let's define exit_thread as an empty inline.
This is a cleanup before we change the prototype of exit_thread to
accept a task parameter.
[akpm@linux-foundation.org: fix mips]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
User visible:
- Honour the kernel.perf_event_max_stack knob more precisely by not counting
PERF_CONTEXT_{KERNEL,USER} when deciding when to stop adding entries to
the perf_sample->ip_callchain[] array (Arnaldo Carvalho de Melo)
- Fix identation of 'stalled-backend-cycles' in 'perf stat' (Namhyung Kim)
- Update runtime using 'cpu-clock' event in 'perf stat' (Namhyung Kim)
- Use 'cpu-clock' for cpu targets in 'perf stat' (Namhyung Kim)
- Avoid fractional digits for integer scales in 'perf stat' (Andi Kleen)
- Store vdso buildid unconditionally, as it appears in callchains and
we're not checking those when creating the build-id table, so we
end up not being able to resolve VDSO symbols when doing analysis
on a different machine than the one where recording was done, possibly
of a different arch even (arm -> x86_64) (He Kuang)
Infrastructure:
- Generalize max_stack sysctl handler, will be used for configuring
multiple kernel knobs related to callchains (Arnaldo Carvalho de Melo)
Cleanups:
- Introduce DSO__NAME_KALLSYMS and DSO__NAME_KCORE, to stop using
open coded strings (Masami Hiramatsu)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=7OdF
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-20160516' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
User visible changes:
- Honour the kernel.perf_event_max_stack knob more precisely by not counting
PERF_CONTEXT_{KERNEL,USER} when deciding when to stop adding entries to
the perf_sample->ip_callchain[] array (Arnaldo Carvalho de Melo)
- Fix identation of 'stalled-backend-cycles' in 'perf stat' (Namhyung Kim)
- Update runtime using 'cpu-clock' event in 'perf stat' (Namhyung Kim)
- Use 'cpu-clock' for cpu targets in 'perf stat' (Namhyung Kim)
- Avoid fractional digits for integer scales in 'perf stat' (Andi Kleen)
- Store vdso buildid unconditionally, as it appears in callchains and
we're not checking those when creating the build-id table, so we
end up not being able to resolve VDSO symbols when doing analysis
on a different machine than the one where recording was done, possibly
of a different arch even (arm -> x86_64) (He Kuang)
Infrastructure changes:
- Generalize max_stack sysctl handler, will be used for configuring
multiple kernel knobs related to callchains (Arnaldo Carvalho de Melo)
Cleanups:
- Introduce DSO__NAME_KALLSYMS and DSO__NAME_KCORE, to stop using
open coded strings (Masami Hiramatsu)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We will use it to count how many addresses are in the entry->ip[] array,
excluding PERF_CONTEXT_{KERNEL,USER,etc} entries, so that we can really
return the number of entries specified by the user via the relevant
sysctl, kernel.perf_event_max_contexts, or via the per event
perf_event_attr.sample_max_stack knob.
This way we keep the perf_sample->ip_callchain->nr meaning, that is the
number of entries, be it real addresses or PERF_CONTEXT_ entries, while
honouring the max_stack knobs, i.e. the end result will be max_stack
entries if we have at least that many entries in a given stack trace.
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-s8teto51tdqvlfhefndtat9r@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This makes perf_callchain_{user,kernel}() receive the max stack
as context for the perf_callchain_entry, instead of accessing
the global sysctl_perf_event_max_stack.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Milian Wolff <milian.wolff@kdab.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Zefan Li <lizefan@huawei.com>
Link: http://lkml.kernel.org/n/tip-kolmn1yo40p7jhswxwrc7rrd@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
- Support for the PMU in Broadcom's Vulcan CPU
- Dynamic event detection using the PMCEIDn_EL0 ID registers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJXNhyFAAoJELescNyEwWM0A0gIAL52VQid16PvLgEO4g6mzv5B
S1ef/y45342R/DYczcUSFboMPuqYSxZ/i7dCwpvLUKX/YjyqQrrGvvS4IYOS99Mp
/OAcf8eTyzzVpJiGQetta3q20gNHGXOxd48R1zcgt+bbEax89lyHQul0A8+rPWLq
RZhEI6Hcq9fb70AjXjWvDxdbbJhtDKc8BGuptygOEqc8LO3mrb1J60TclU629XOH
Jn4Vdu5f6Rx8hPFdw5HXn+Vdheymphz0qj1lyGCQS4Am97bM5J/54a/A4tyHnHuQ
s9Y26NIAvrktp9wCMlXGQhYL94e1rZowXCWxF98D9XrlIzYORIdf/OZ5DCS8LCA=
=0ntf
-----END PGP SIGNATURE-----
Merge tag 'arm64-perf' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 perf updates from Will Deacon:
"The main addition here is support for Broadcom's Vulcan core using the
architected ID registers for discovering supported events.
- Support for the PMU in Broadcom's Vulcan CPU
- Dynamic event detection using the PMCEIDn_EL0 ID registers"
* tag 'arm64-perf' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: perf: don't expose CHAIN event in sysfs
arm64/perf: Add Broadcom Vulcan PMU support
arm64/perf: Filter common events based on PMCEIDn_EL0
arm64/perf: Access pmu register using <read/write>_sys_reg
arm64/perf: Define complete ARMv8 recommended implementation defined events
arm64/perf: Changed events naming as per the ARM ARM
arm64: dts: Add Broadcom Vulcan PMU in dts
Documentation: arm64: pmu: Add Broadcom Vulcan PMU binding
- virt_to_page/page_address optimisations
- Support for NUMA systems described using device-tree
- Support for hibernate/suspend-to-disk
- Proper support for maxcpus= command line parameter
- Detection and graceful handling of AArch64-only CPUs
- Miscellaneous cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJXNbgkAAoJELescNyEwWM0PtcIAK11xaOMmSqXz8fcTeNLw4dS
taaPWhjCYus8EhJyvTetfwk74+qVApdvKXKNKgODJXQEjeQx2brdUfbQZb31DTGT
798UYCAyEYCWkXspqi+/dpZEgUGPYH7uGOu2eDd19+PhTeX/EQSRX3fC9k0BNhvh
PN9pOgRcKAlIExZ6QYmT0g56VLtbCfFShN41mQ8HdpShl6pPJuhQ+kDDzudmRjuD
11/oYuOaVTnwbPuXn+sjOrWvMkfINHI70BAQnnBs0v+5c45mzpqEMsy0dYo2Pl2m
ar5lUFVIZggQkiqcOzqBzEgF+4gNw4LUu1DgK6cNKNMtL6k8E9zeOZMWeSVr0lg=
=bT5E
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
- virt_to_page/page_address optimisations
- support for NUMA systems described using device-tree
- support for hibernate/suspend-to-disk
- proper support for maxcpus= command line parameter
- detection and graceful handling of AArch64-only CPUs
- miscellaneous cleanups and non-critical fixes
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (92 commits)
arm64: do not enforce strict 16 byte alignment to stack pointer
arm64: kernel: Fix incorrect brk randomization
arm64: cpuinfo: Missing NULL terminator in compat_hwcap_str
arm64: secondary_start_kernel: Remove unnecessary barrier
arm64: Ensure pmd_present() returns false after pmd_mknotpresent()
arm64: Replace hard-coded values in the pmd/pud_bad() macros
arm64: Implement pmdp_set_access_flags() for hardware AF/DBM
arm64: Fix typo in the pmdp_huge_get_and_clear() definition
arm64: mm: remove unnecessary EXPORT_SYMBOL_GPL
arm64: always use STRICT_MM_TYPECHECKS
arm64: kvm: Fix kvm teardown for systems using the extended idmap
arm64: kaslr: increase randomization granularity
arm64: kconfig: drop CONFIG_RTC_LIB dependency
arm64: make ARCH_SUPPORTS_DEBUG_PAGEALLOC depend on !HIBERNATION
arm64: hibernate: Refuse to hibernate if the boot cpu is offline
arm64: kernel: Add support for hibernate/suspend-to-disk
PM / Hibernate: Call flush_icache_range() on pages restored in-place
arm64: Add new asm macro copy_page
arm64: Promote KERNEL_START/KERNEL_END definitions to a header file
arm64: kernel: Include _AC definition in page.h
...
Pull perf updates from Ingo Molnar:
"Bigger kernel side changes:
- Add backwards writing capability to the perf ring-buffer code,
which is preparation for future advanced features like robust
'overwrite support' and snapshot mode. (Wang Nan)
- Add pause and resume ioctls for the perf ringbuffer (Wang Nan)
- x86 Intel cstate code cleanups and reorgnization (Thomas Gleixner)
- x86 Intel uncore and CPU PMU driver updates (Kan Liang, Peter
Zijlstra)
- x86 AUX (Intel PT) related enhancements and updates (Alexander
Shishkin)
- x86 MSR PMU driver enhancements and updates (Huang Rui)
- ... and lots of other changes spread out over 40+ commits.
Biggest tooling side changes:
- 'perf trace' features and enhancements. (Arnaldo Carvalho de Melo)
- BPF tooling updates (Wang Nan)
- 'perf sched' updates (Jiri Olsa)
- 'perf probe' updates (Masami Hiramatsu)
- ... plus 200+ other enhancements, fixes and cleanups to tools/
The merge commits, the shortlog and the changelogs contain a lot more
details"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (249 commits)
perf/core: Disable the event on a truncated AUX record
perf/x86/intel/pt: Generate PMI in the STOP region as well
perf buildid-cache: Use lsdir() for looking up buildid caches
perf symbols: Use lsdir() for the search in kcore cache directory
perf tools: Use SBUILD_ID_SIZE where applicable
perf tools: Fix lsdir to set errno correctly
perf trace: Move seccomp args beautifiers to tools/perf/trace/beauty/
perf trace: Move flock op beautifier to tools/perf/trace/beauty/
perf build: Add build-test for debug-frame on arm/arm64
perf build: Add build-test for libunwind cross-platforms support
perf script: Fix export of callchains with recursion in db-export
perf script: Fix callchain addresses in db-export
perf script: Fix symbol insertion behavior in db-export
perf symbols: Add dso__insert_symbol function
perf scripting python: Use Py_FatalError instead of die()
perf tools: Remove xrealloc and ALLOC_GROW
perf help: Do not use ALLOC_GROW in add_cmd_list
perf pmu: Make pmu_formats_string to check return value of strbuf
perf header: Make topology checkers to check return value of strbuf
perf tools: Make alias handler to check return value of strbuf
...
copy_thread should not be enforcing 16 byte aligment and returning
-EINVAL. Other architectures trap misaligned stack access with SIGBUS
so arm64 should follow this convention, so remove the strict enforcement
check.
For example, currently clone(2) fails with -EINVAL when passing
a misaligned stack and this gives little clue to what is wrong. Instead,
it is arguable that a SIGBUS on the fist access to a misaligned stack
allows one to figure out that it is a misaligned stack issue rather
than trying to figure out why an unconventional (and undocumented)
-EINVAL is being returned.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This fixes two issues with the arm64 brk randomziation. First, the
STACK_RND_MASK was being used incorrectly. The original code was:
unsigned long range_end = base + (STACK_RND_MASK << PAGE_SHIFT) + 1;
STACK_RND_MASK is 0x7ff (32-bit) or 0x3ffff (64-bit), with 4K pages where
PAGE_SHIFT is 12:
#define STACK_RND_MASK (test_thread_flag(TIF_32BIT) ? \
0x7ff >> (PAGE_SHIFT - 12) : \
0x3ffff >> (PAGE_SHIFT - 12))
This means the resulting offset from base would be 0x7ff0001 or 0x3ffff0001,
which is wrong since it creates an unaligned end address. It was likely
intended to be:
unsigned long range_end = base + ((STACK_RND_MASK + 1) << PAGE_SHIFT)
Which would result in offsets of 0x800000 (32-bit) and 0x40000000 (64-bit).
However, even this corrected 32-bit compat offset (0x00800000) is much
smaller than native ARM's brk randomization value (0x02000000):
unsigned long arch_randomize_brk(struct mm_struct *mm)
{
unsigned long range_end = mm->brk + 0x02000000;
return randomize_range(mm->brk, range_end, 0) ? : mm->brk;
}
So, instead of basing arm64's brk randomization on mistaken STACK_RND_MASK
calculations, just use specific corrected values for compat (0x2000000)
and native arm64 (0x40000000).
Reviewed-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
[will: use is_compat_task() as suggested by tixy]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The loop that browses the array compat_hwcap_str will stop when a NULL
is encountered, however NULL is missing at the end of array. This will
lead to overrun until a NULL is found somewhere in the following memory.
In reality, this works out because the compat_hwcap2_str array tends to
follow immediately in memory, and that *is* terminated correctly.
Furthermore, the unsigned int compat_elf_hwcap is checked before
printing each capability, so we end up doing the right thing because
the size of the two arrays is less than 32. Still, this is an obvious
mistake and should be fixed.
Note for backporting: commit 12d11817ea ("arm64: Move
/proc/cpuinfo handling code") moved this code in v4.4. Prior to that
commit, the same change should be made in arch/arm64/kernel/setup.c.
Fixes: 44b82b7700 "arm64: Fix up /proc/cpuinfo"
Cc: <stable@vger.kernel.org> # v3.19+ (but see note above prior to v4.4)
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Remove the unnecessary smp_wmb(), which was added to make sure
that the update_cpu_boot_status() completes before we mark the
CPU online. But update_cpu_boot_status() already has dsb() (required
for the failing CPUs) to ensure the correct behavior.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Dennis Chen <dennis.chen@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Hibernation represents a system state save/restore through
a system reboot; this implies that the logical cpus carrying
out hibernation/thawing must be the same, so that the context
saved in the snapshot image on hibernation is consistent with
the state of the system on resume. If resume from hibernation
is driven through kernel command line parameter, the cpu responsible
for thawing the system will be whatever CPU firmware boots the system
on upon cold-boot (ie logical cpu 0); this means that in order to
keep system context consistent between the hibernate snapshot image
and system state on kernel resume from hibernate, logical cpu 0 must
be online on hibernation and must be the logical cpu that creates
the snapshot image.
This patch adds a PM notifier that enforces logical cpu 0 is online
when the hibernation is started (and prevents hibernation if it is
not), which is sufficient to guarantee it will be the one creating
the snapshot image therefore providing the resume cpu a consistent
snapshot of the system to resume to.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add support for hibernate/suspend-to-disk.
Suspend borrows code from cpu_suspend() to write cpu state onto the stack,
before calling swsusp_save() to save the memory image.
Restore creates a set of temporary page tables, covering only the
linear map, copies the restore code to a 'safe' page, then uses the copy to
restore the memory image. The copied code executes in the lower half of the
address space, and once complete, restores the original kernel's page
tables. It then calls into cpu_resume(), and follows the normal
cpu_suspend() path back into the suspend code.
To restore a kernel using KASLR, the address of the page tables, and
cpu_resume() are stored in the hibernate arch-header and the el2
vectors are pivotted via the 'safe' page in low memory.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Kevin Hilman <khilman@baylibre.com> # Tested on Juno R2
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
KERNEL_START and KERNEL_END are useful outside head.S, move them to a
header file.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
By enabling the MMU early in cpu_resume(), the sleep_save_sp and stack can
be accessed by VA, which avoids the need to convert-addresses and clean to
PoC on the suspend path.
MMU setup is shared with the boot path, meaning the swapper_pg_dir is
restored directly: ttbr1_el1 is no longer saved/restored.
struct sleep_save_sp is removed, replacing it with a single array of
pointers.
cpu_do_{suspend,resume} could be further reduced to not restore: cpacr_el1,
mdscr_el1, tcr_el1, vbar_el1 and sctlr_el1, all of which are set by
__cpu_setup(). However these values all contain res0 bits that may be used
to enable future features.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Hibernate could make use of the cpu_suspend() code to save/restore cpu
state, however it needs to be able to return '0' from the 'finisher'.
Rework cpu_suspend() so that the finisher is called from C code,
independently from the save/restore of cpu state. Space to save the context
in is allocated in the caller's stack frame, and passed into
__cpu_suspend_enter().
Hibernate's use of this API will look like a copy of the cpu_suspend()
function.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A later patch implements kvm_arch_hardware_disable(), to remove kvm
from el2, and re-instate the hyp-stub.
This can happen while guests are running, particularly when kvm_reboot()
calls kvm_arch_hardware_disable() on each cpu. This can interrupt a guest,
remove kvm, then allow the guest to be scheduled again. This causes
kvm_call_hyp() to be run against the hyp-stub.
Change the hyp-stub to return a new exception type when this happens,
and add code to kvm's handle_exit() to tell userspace we failed to
enter the guest.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The existing arm64 hcall implementations are limited in that they only
allow for two distinct hcalls; with the x0 register either zero or not
zero. Also, the API of the hyp-stub exception vector routines and the
KVM exception vector routines differ; hyp-stub uses a non-zero value in
x0 to implement __hyp_set_vectors, whereas KVM uses it to implement
kvm_call_hyp.
To allow for additional hcalls to be defined and to make the arm64 hcall
API more consistent across exception vector routines, change the hcall
implementations to reserve all x0 values below 0xfff for hcalls such
as {s,g}et_vectors().
Define two new preprocessor macros HVC_GET_VECTORS, and HVC_SET_VECTORS
to be used as hcall type specifiers and convert the existing
__hyp_get_vectors() and __hyp_set_vectors() routines to use these new
macros when executing an HVC call. Also, change the corresponding
hyp-stub and KVM el1_sync exception vector routines to use these new
macros.
Signed-off-by: Geoff Levand <geoff@infradead.org>
[Merged two hcall patches, moved immediate value from esr to x0, use lr
as a scratch register, changed limit to 0xfff]
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Suzuki K Poulose