In commit 734643dfbd ("usb: dwc2: host: add flag to reflect bus
state") we changed dwc2_port_suspend() not to set the lx_state
anymore (instead it sets the new bus_suspended variable). This
introduced a bug where we would fail to detect device insertions if:
1. Plug empty hub into dwc2
2. Plug USB flash drive into the empty hub.
3. Wait a few seconds
4. Unplug USB flash drive
5. Less than 2 seconds after step 4, plug the USB flash drive in again.
The dwc2_hcd_rem_wakeup() function should have been changed to look at
the new bus_suspended variable.
Let's fix it. Since commit b46146d59f ("usb: dwc2: host: resume root
hub on remote wakeup") talks about needing the root hub resumed if the
bus was suspended, we'll include it in our test.
It appears that the "port_l1_change" should only be set to 1 if we were
in DWC2_L1 (the driver currently never sets this), so we'll update the
former "else" case based on this test.
Fixes: 734643dfbd ("usb: dwc2: host: add flag to reflect bus state")
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Gregory Herrero <gregory.herrero@intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The comment for ahbcfg for rk3066 parameters (also used for rk3288)
claimed that ahbcfg was INCR16, but it wasn't. Since the bits weren't
shifted properly, the 0x7 ended up being masked and we ended up
programming 0x3 for the HBstLen. Let's set it to INCR16 properly.
As per Wu Liang Feng at Rockchip this may increase transmission
efficiency. I did blackbox tests with writing 0s to a USB-based SD
reader (forcefully capping CPU Freq to try to measure efficiency):
cd /sys/devices/system/cpu/cpu0/cpufreq
echo userspace > scaling_governor
echo 126000 > scaling_setspeed
for i in $(seq 10); do
dd if=/dev/zero of=/dev/sdb bs=1M count=750
done
With the above tests I found that speeds went from ~15MB/s to ~18MB/s.
Note that most other tests I did (including reading from the same USB
reader) didn't show any difference in performance.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Liangfeng Wu <wulf@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
While plugging / unplugging on a DWC2 host port with "slub_debug=FZPUA"
enabled, I found a crash that was quite obviously a use after free.
It appears that in some cases when we handle the various sub-cases of
HCINT we may end up freeing the QTD. If there is more than one bit set
in HCINT we may then end up continuing to use the QTD, which is bad.
Let's be paranoid and check for this after each sub-case. This should
be safe since we officially have the "hsotg->lock" (it was grabbed in
dwc2_handle_hcd_intr).
The specific crash I found was:
Unable to handle kernel paging request at virtual address 6b6b6b9f
At the time of the crash, the kernel reported:
(dwc2_hc_nak_intr+0x5c/0x198)
(dwc2_handle_hcd_intr+0xa84/0xbf8)
(_dwc2_hcd_irq+0x1c/0x20)
(usb_hcd_irq+0x34/0x48)
Popping into kgdb found that "*qtd" was filled with "0x6b", AKA qtd had
been freed and filled with slub_debug poison.
kgdb gave a little better stack crawl:
0 dwc2_hc_nak_intr (hsotg=hsotg@entry=0xec42e058,
chan=chan@entry=0xec546dc0, chnum=chnum@entry=4,
qtd=qtd@entry=0xec679600) at drivers/usb/dwc2/hcd_intr.c:1237
1 dwc2_hc_n_intr (chnum=4, hsotg=0xec42e058) at
drivers/usb/dwc2/hcd_intr.c:2041
2 dwc2_hc_intr (hsotg=0xec42e058) at drivers/usb/dwc2/hcd_intr.c:2078
3 dwc2_handle_hcd_intr (hsotg=0xec42e058) at
drivers/usb/dwc2/hcd_intr.c:2128
4 _dwc2_hcd_irq (hcd=<optimized out>) at drivers/usb/dwc2/hcd.c:2837
5 usb_hcd_irq (irq=<optimized out>, __hcd=<optimized out>) at
drivers/usb/core/hcd.c:2353
Popping up to frame #1 (dwc2_hc_n_intr) found:
(gdb) print /x hcint
$12 = 0x12
AKA:
#define HCINTMSK_CHHLTD (1 << 1)
#define HCINTMSK_NAK (1 << 4)
Further debugging found that by simulating receiving those two
interrupts at the same time it was trivial to replicate the
use-after-free. See <http://crosreview.com/305712> for a patch and
instructions. This lead to getting the following stack crawl of the
actual free:
0 arch_kgdb_breakpoint () at arch/arm/include/asm/outercache.h:103
1 kgdb_breakpoint () at kernel/debug/debug_core.c:1054
2 dwc2_hcd_qtd_unlink_and_free (hsotg=<optimized out>, qh=<optimized
out>, qtd=0xe4479a00) at drivers/usb/dwc2/hcd.h:488
3 dwc2_deactivate_qh (free_qtd=<optimized out>, qh=0xe5efa280,
hsotg=0xed424618) at drivers/usb/dwc2/hcd_intr.c:671
4 dwc2_release_channel (hsotg=hsotg@entry=0xed424618,
chan=chan@entry=0xed5be000, qtd=<optimized out>,
halt_status=<optimized out>) at drivers/usb/dwc2/hcd_intr.c:742
5 dwc2_halt_channel (hsotg=0xed424618, chan=0xed5be000, qtd=<optimized
out>, halt_status=<optimized out>) at
drivers/usb/dwc2/hcd_intr.c:804
6 dwc2_complete_non_periodic_xfer (chnum=<optimized out>,
halt_status=<optimized out>, qtd=<optimized out>, chan=<optimized
out>, hsotg=<optimized out>) at drivers/usb/dwc2/hcd_intr.c:889
7 dwc2_hc_xfercomp_intr (hsotg=hsotg@entry=0xed424618,
chan=chan@entry=0xed5be000, chnum=chnum@entry=6,
qtd=qtd@entry=0xe4479a00) at drivers/usb/dwc2/hcd_intr.c:1065
8 dwc2_hc_chhltd_intr_dma (qtd=0xe4479a00, chnum=6, chan=0xed5be000,
hsotg=0xed424618) at drivers/usb/dwc2/hcd_intr.c:1823
9 dwc2_hc_chhltd_intr (qtd=0xe4479a00, chnum=6, chan=0xed5be000,
hsotg=0xed424618) at drivers/usb/dwc2/hcd_intr.c:1944
10 dwc2_hc_n_intr (chnum=6, hsotg=0xed424618) at
drivers/usb/dwc2/hcd_intr.c:2052
11 dwc2_hc_intr (hsotg=0xed424618) at drivers/usb/dwc2/hcd_intr.c:2097
12 dwc2_handle_hcd_intr (hsotg=0xed424618) at
drivers/usb/dwc2/hcd_intr.c:2147
13 _dwc2_hcd_irq (hcd=<optimized out>) at drivers/usb/dwc2/hcd.c:2837
14 usb_hcd_irq (irq=<optimized out>, __hcd=<optimized out>) at
drivers/usb/core/hcd.c:2353
Though we could add specific code to handle this case, adding the
general purpose code to check for all cases where qtd might be freed
seemed safer.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
From code inspection, it appears to be unsafe to do a read-modify-write
of PCGCTL in dwc2_port_resume(). Let's make sure the spinlock is held
around this operation.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC2 module on some platforms needs three additional hardware
resources: phy controller, clock and power supply. All of them must be
enabled/activated to properly initialize and operate. This was initially
handled in s3c-hsotg driver, which has been converted to 'gadget' part
of dwc2 driver. Unfortunately, not all of this code got moved to common
platform code, what resulted in accessing DWC2 registers without
enabling low-level hardware resources. This fails for example on Exynos
SoCs. This patch moves all the code for managing those resources to
common platform.c file and provides convenient wrappers for controlling
them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
init_mutex is a leftover from the time, when s3c-hsotg driver did not
implement proper pull up/down control and emulated it by enabling
enabling/disabling usb phy. Proper pull up/down control has been added
by commit 5b9451f8c4 ("usb: dwc2: gadget:
use soft-disconnect udc feature in pullup() method"), so init_muxtex can
be removed now to avoid potential deadlocks with other locks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix a duplicate argument warning reported by 0-DAY kernel test
infrastructure in the following patch:
77dbf71 usb: dwc2: host: add disconnect interrupt to host only interrupts
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB OTG driver in isochronous mode has to set the parity of the receiving
microframe. The parity is set to even by default. This causes problems for
an audio gadget, if the host starts transmitting on odd microframes.
This fix uses Incomplete Periodic Transfer interrupt to toggle between
even and odd parity until the Transfer Complete interrupt is received.
Signed-off-by: Roman Bacik <rbacik@broadcom.com>
Reviewed-by: Abhinav Ratna <aratna@broadcom.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Even when DWC2 is in (internal) suspended state, it should disable PHY
in suspend and then enable it in resume. This patch fixes unbalanced PHY
control sequence.
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During typical gadget operation, dwc2 clock was enabled 3 times: from
dwc2_gadget_init(), dwc2_hsotg_udc_start() and dwc2_hsotg_pullup(), and
then disabled in s3c_hsotg_pullup(), s3c_hsotg_udc_stop() and
dwc2_hsotg_remove(). This really makes no sense, so leave clock control
code only in dwc2_gadget_init/remove functions.
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes doubled call to dwc2_hsotg_of_probe() function.
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When dwc2_hsotg_handle_unaligned_buf_complete() hs_req->req.buf
already destroyed, in dwc2_hsotg_unmap_dma(), it touches
hs_req->req.dma again, so dwc2_hsotg_unmap_dma() should be called
before dwc2_hsotg_handle_unaligned_buf_complete(). Otherwise, it
will cause a bad_page BUG, when allocate this memory page next
time.
This bug led to the following crash:
BUG: Bad page state in process swapper/0 pfn:2bdbc
[ 26.820440] page:eed76780 count:0 mapcount:0 mapping: (null) index:0x0
[ 26.854710] page flags: 0x200(arch_1)
[ 26.885836] page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
[ 26.919179] bad because of flags:
[ 26.948917] page flags: 0x200(arch_1)
[ 26.979100] Modules linked in:
[ 27.008401] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W3.14.0 #17
[ 27.041816] [<c010e1f8>] (unwind_backtrace) from [<c010a704>] (show_stack+0x20/0x24)
[ 27.076108] [<c010a704>] (show_stack) from [<c087eea8>] (dump_stack+0x70/0x8c)
[ 27.110246] [<c087eea8>] (dump_stack) from [<c01ce0b8>] (bad_page+0xfc/0x12c)
[ 27.143958] [<c01ce0b8>] (bad_page) from [<c01ce65c>] (get_page_from_freelist+0x3e4/0x50c)
[ 27.179298] [<c01ce65c>] (get_page_from_freelist) from [<c01ce9a0>] (__alloc_pages_nodemask)
[ 27.216296] [<c01ce9a0>] (__alloc_pages_nodemask) from [<c01cf00c>] (__get_free_pages+0x20/)
[ 27.252326] [<c01cf00c>] (__get_free_pages) from [<c01e5bec>] (kmalloc_order_trace+0x34/0xa)
[ 27.288295] [<c01e5bec>] (kmalloc_order_trace) from [<c0203304>] (__kmalloc+0x40/0x1ac)
[ 27.323751] [<c0203304>] (__kmalloc) from [<c052abc0>] (dwc2_hsotg_ep_queue.isra.12+0x7c/0x1)
[ 27.359937] [<c052abc0>] (dwc2_hsotg_ep_queue.isra.12) from [<c052af88>] (dwc2_hsotg_ep_queue)
[ 27.397478] [<c052af88>] (dwc2_hsotg_ep_queue_lock) from [<c0554110>] (rx_submit+0xfc/0x164)
[ 27.433619] [<c0554110>] (rx_submit) from [<c05546e8>] (rx_complete+0x22c/0x230)
[ 27.468872] [<c05546e8>] (rx_complete) from [<c052b528>] (dwc2_hsotg_complete_request+0xfc/0)
[ 27.506240] [<c052b528>] (dwc2_hsotg_complete_request) from [<c052bba0>] (dwc2_hsotg_handle_o)
[ 27.545401] [<c052bba0>] (dwc2_hsotg_handle_outdone) from [<c052be70>] (dwc2_hsotg_epint+0x2c)
[ 27.583689] [<c052be70>] (dwc2_hsotg_epint) from [<c052c750>] (dwc2_hsotg_irq+0x1dc/0x4ac)
[ 27.621041] [<c052c750>] (dwc2_hsotg_irq) from [<c01682e0>] (handle_irq_event_percpu+0x70/0x)
[ 27.659066] [<c01682e0>] (handle_irq_event_percpu) from [<c01684ec>] (handle_irq_event+0x4c)
[ 27.697322] [<c01684ec>] (handle_irq_event) from [<c016bae0>] (handle_fasteoi_irq+0xc8/0x11)
[ 27.735451] [<c016bae0>] (handle_fasteoi_irq) from [<c0167b8c>] (generic_handle_irq+0x30/0x)
[ 27.773918] [<c0167b8c>] (generic_handle_irq) from [<c0167ca4>] (__handle_domain_irq+0x84/0)
[ 27.812018] [<c0167ca4>] (__handle_domain_irq) from [<c01003b0>] (gic_handle_irq+0x48/0x6c)
[ 27.849695] [<c01003b0>] (gic_handle_irq) from [<c010b340>] (__irq_svc+0x40/0x50)
[ 27.886907] Exception stack(0xc0d01ee0 to 0xc0d01f28)
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Controller enters hibernation through suspend interrupt on
disconnection. On connection, session request interrupt is generated.
dwc2 must exit hibernation and restore state from this interrupt
before continuing.
In host mode, exit from hibernation is handled by bus_resume function.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If system is loaded, reset, enum-done and setup interrupts can occur
at the same time. Current interrupt handling sequence will handle
setup packet's interrupt before handling reset interrupt. Which will
break the enumeration process. Correct sequence is to handle reset,
enum-done and then any other endpoint interrupts.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When disconnecting cable, controller will detect a suspend condition
and enter partial power down. If vbus_session is called by the phy
driver during hibernation, make sure controller exit hibernation
before it is accessed.
Signed-off-by: Jianqiang Tang <jianqiang.tang@intel.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
idstschng interrupt should not be used when id pin control is
external. This is already handled on dwc2 host part. Fix it on gadget
part as well.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a 200ms guard period to avoid unnecessary resets of the dwc2
ip. This delay sometimes prove to be too large when usbcv is run with
an ehci host. dwc2 only needs to be reset after addressed state.
Change the logic to reset ip after addressed state.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure there are no requests pending on ep0 before reinitializing
core. Otherwise, dwc2_hsotg_enqueue_setup will fail afterwards.
Also, take hsotg->lock before calling
dwc2_hsotg_core_init_disconnected() from dwc2_conn_id_status_change()
as dwc2_hsotg_complete_request() expect lock to be held.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the request being dequeued is already started, disable endpoint
to stop the transfer and then call dwc2_hsotg_complete_request().
Endpoint will be re-enabled on next call to dwc2_hsotg_start_req().
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
wIndex field was missing. Also print in natural order instead of
Req first, so that its easier to compare for example against
bus analyzer logs.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc2_hsotg_start_req starts a request only if endpoint is not stalled.
Ignore this check for ep0 as core will clear DOEPCTL0.Stall after
sending stall handshake. Prepare instead for receiving next setup
packet.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No point of continue with initialization if core is not in a sane
state.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some device may have external id pin control enabled, so op_state
will not be set on id pin interrupt change.
Thus, ensure op_state is set to peripheral during vbus detection.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Modifying the pullup state during host mode trig a new enumeration
of attached device. Thus, avoid modifying pullup in host mode.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If dual role configuration is not selected, check and force dr_mode
based on the selected configuration.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ID status change interrupt will not be handled in peripheral only
configuration. So initialize op_state during gadget init.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Correctly update lx_state on gadget connection and disconnection.
When usb cable is disconnected, lx_state must be updated to L3 as
controller could be in power off state.
When usb cable is connected, lx_state must be updated to L0 as
controller is powered.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On a disconnect, dwc2 will kill all remaining urbs from qh list.
urbs are given back to hcd with -ETIMEDOUT status.
Some usb device driver, like mass storage, will unlink all urbs
using usb_hcd_unlink_urb when receiving a negative status different
from -ECONNRESET.
The following flow will then happen:
dwc2_hcd_disconnect()
-> dwc2_kill_all_urbs() try to kill first pending urb.
-> dwc2_host_complete(-ETIMEDOUT)
-> usb_hcd_giveback_urb(-ETIMEDOUT)
-> sg_complete()
-> usb_unlink_urb()
-> usb_put_dev(urb->dev)
-> dwc2_kill_all_urbs() try to kill next pending urb.
-> dwc2_host_complete(-ETIMEDOUT)
-> usb_hcd_giveback_urb(-ETIMEDOUT)
-> NULL pointer dereferencing because urb->dev has been freed for all
urbs of this device.
The root cause of this NULL pointer is to call call usb_unlink_urb()
while we are killing all urbs. To avoid this return urb with
-ECONNRESET status
This issue usually happens while removing mass storage device during
transfer.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On first qh initialization, hsotg->frame_number is not corresponding
to reality. So read it from host controller to get correct value.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Print urb->iso_frame_desc.status after it has been updated using
dwc2_hcd_urb_get_iso_desc_status().
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some high speed mass storage devices fail to enumerate with following
error:
Cannot enable port %i. Maybe the USB cable is bad?
This happens only when the device is plugged while the controller
is in hibernation state. After exiting hibernation, the controller
detects the device as a low speed device and fail to enumerate it.
Problem occurs only if HPRT0.PWR bit is programmed in a too short
delay after exiting hibernation. Dumping hprt register in
_dwc2_hcd_resume() directly after dwc2_exit_hibernation() shows that
HPRT0.LNSTS (D+/D- level) becomes valid approximately 2ms after
exiting hibernation.
Since dwc2_exit_hibernation() is called from atomic context, move the
delay out of this function.
Delay value is experimental and not mentioned in Synopsys
documentation. To be on the safe side 3ms delay is used.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If an interrupt rises during hibernation process, dwc2 will assert
interrupt line to interrupt controller. If interrupt is level
sensitive, interrupt handler will be called in a loop because dwc2
will not be able to clear it while controller is hibernated.
Thus, clear all controller interrupts before hibernation entry.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disable host interrupts before synchronising dwc2 irq.
So that interrupts are not generated once controller is stopped.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
GINTSTS.DisconnInt is host only interrupt and should be disable after
dwc2_disable_host_interrupts is called.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case controller is asked to stop while devices are connected,
disconnect all devices and clean up before stopping.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Frame number is reset in hardware after exiting hibernation.
Thus, reset frame_number and ensure qh are queued with correct
sched_frame.
Otherwise, qh->sched_frame may be too high compared to
current frame number (which is 0). This can delay addition of qh in
the list of transfers until frame number reaches qh->sched_frame.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Port can be resumed in bus_resume callback.
In this case, there is no need to drive resume a second time
when hcd ask for it.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If hibernation is supported, resume of devices will be handled in
bus_resume callback.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a device is disconnected, lx_state must not be changed since the
device may be disconnected whereas controller is still powered.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During hcd initialization, hardware accessible flag and lx_state must
be reset to the working state since controller is powered at this stage.
Same logic applied for stop callback.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disable controller power and enter hibernation when usb bus is
suspended. A phy driver is required to disable the power of the
controller and detect remote-wakeup or disconnection since the
controller will not be able to detect these in this state.
Once the phy driver detects bus activity, it must call
usb_hcd_resume_root_hub.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
lx_state must be used to reflect controller power state only and not
bus state. Thus add a flag to track state during bus suspend.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
port resume sequence may be used in different places. Create a
function to handle it. Make hprt0 read-modify-write atomic and
clear HPRT0_SUSP for both writes as it is a "read, write-set,
and self-clear (R_WS_SC)" bit. Since the lock is released
between the writes, read hprt0 again.
Since the phy clock is stopped in dwc2_port_suspend(), enable it
here and remove the PCGCTL write from dwc2_hcd_hub_control()
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When entering hibernation hprt0 must be read using dwc2_read_hprt0().
Otherwise, any set hprt0 status bits will be cleared when restoring
hprt0 on exit from hibernation.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.
This patch is necessary to access dwc2 registers correctly on big-endian
systems such as the mips based SoCs made by Lantiq. Then dwc2 can be
used to replace ifx-hcd driver for Lantiq platforms found e.g. in
OpenWrt.
The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h
Some files were then hand-edited to fix checkpatch.pl warnings about
too long lines.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this driver has long ago became dwc2.ko with
both peripheral and host roles, there's no point
in keeping the old function names.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fix spelling typo inv various part of sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Douglas Anderson