Use the of_device_get_match_data() helper instead of open coding.
While at it, make config const so the cast can be dropped.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
platform_get_irq() returns an error code, but the sh_flctl
driver ignores it and always returns -ENXIO. This is not correct
and, prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The return value of dma_map_single() should be checked by
dma_mapping_error(). However, in function flctl_dma_fifo0_transfer(), its
return value is checked against NULL, which could result in failures.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Peter Pan <peterpandong@micron.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Han Xu <han.xu@nxp.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-By: Harvey Hunt <harveyhuntnexus@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
A lot of drivers are providing their own ->cmdfunc(), and most of the
time this implementation does not support all possible NAND operations.
But since ->cmdfunc() cannot return an error code, the core has no way
to know that the operation it requested is not supported.
This is a problem we cannot address for all kind of operations with the
current design, but we can prevent these silent failures for the
GET/SET FEATURES operation by overloading the default
->onfi_{set,get}_features() methods with one returning -ENOTSUPP.
Reported-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Some build tools noticed that 'cookie' is being set but not used. Might
as well catch the errors here and handle them the same way we handle
other DMA prep steps.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is part of process deprecating NAND_ECC_SOFT_BCH (and switching to
enum nand_ecc_algo).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
By convention, the FIFO address we pass using dmaengine_slave_config
is a physical address in the form that is understood by the DMA
engine, as a dma_addr_t, phys_addr_t or resource_size_t.
The sh_flctl driver however passes a virtual __iomem address that
gets cast to dma_addr_t in the slave driver. This happens to work
on shmobile because that platform sets up an identity mapping for
its MMIO regions, but such code is not portable to other platforms,
and prevents us from ever changing the platform mapping or reusing
the driver on other architectures like ARM64 that might not have the
mapping.
We also get a warning about a type mismatch for the case that
dma_addr_t is wider than a pointer, i.e. when CONFIG_LPAE is set:
drivers/mtd/nand/sh_flctl.c: In function 'flctl_setup_dma':
drivers/mtd/nand/sh_flctl.c:163:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
cfg.dst_addr = (dma_addr_t)FLDTFIFO(flctl);
This changes the driver to instead pass the physical address of
the FIFO that is extracted from the MMIO resource, making the
code more portable and avoiding the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtd_to_nand() now uses the container_of() approach to transform an
mtd_info pointer into a nand_chip one. Drop useless mtd->priv
assignments from NAND controller drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
struct nand_chip now embeds an mtd device. Make use of this mtd instance.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
All of these drivers set up a parser data struct just to communicate DT
partition data. This field has been deprecated and is instead supported
by telling nand_scan_ident() about the 'flash_node'.
This patch:
* sets chip->flash_node for those drivers that didn't already (but used
OF partitioning)
* drops the parser data
* switches to the simpler mtd_device_register() where possible, now
that we've eliminated one of the auxiliary parameters
Now that we've assigned chip->flash_node for these drivers, we can
probably rely on nand_dt_init() to do more of the DT parsing for us, but
for now, I don't want to fiddle with each of these drivers. The parsing
is done in duplicate for now on some drivers. I don't think this should
break things. (Famous last words.)
(Rolled in some changes by Boris Brezillon)
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The ->read_xxx() methods are all passed the page number the NAND controller
is supposed to read, but ->write_xxx() do not have such a parameter.
This is a problem if we want to properly implement data
scrambling/randomization in order to mitigate MLC sensibility to repeated
pattern: to prevent bitflips in adjacent pages in the same block we need
to avoid repeating the same pattern at the same offset in those pages,
hence the randomizer/scrambler engine need to be passed the page value
in order to adapt its seed accordingly.
Moreover, adding the page parameter to the ->write_xxx() methods add some
consistency to the current API.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Josh Wu <josh.wu@atmel.com>
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Huang Shijie <shijie.huang@arm.com>
CC: Stefan Agner <stefan@agner.ch>
CC: devel@driverdev.osuosl.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Current sh_flctl sets dma_slave_config :: slave_id field for DMAEngine,
but it is no longer needed. Let's remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rename symbols, variables, functions and structure fields related do
the resume latency device PM QoS type so that it is clear where they
belong (in particular, to avoid confusion with the latency tolerance
device PM QoS type introduced by a subsequent changeset).
Update the PM QoS documentation to better reflect its current state.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since the of_mtd header provides dummy stubs for !CONFIG_OF, it's safe
to remove the #ifdef CONFIG_OF. Build tested only.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cast pointers to uintptr_t instead of unsigned int. This fixes warnings
on platforms where pointers have a different size than int.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlDSAa4ACgkQdwG7hYl686MMcACeNYa//ghPtccb5L+IRXsqaFDL
Yi4AoLWOaOjN8qM4KUF/bfMEkwNGAePz
=DaAQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd
Pull MTD updates from David Woodhouse:
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
mtd: nand: typo in nand_id_has_period() comments
mtd: nand/gpio: use io{read,write}*_rep accessors
mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
mtd: nand/docg4: fix and improve read of factory bbt
mtd: nand/docg4: reserve bb marker area in ecclayout
mtd: nand/docg4: add support for writing in reliable mode
mtd: mxc_nand: reorder part_probes to let cmdline override other sources
mtd: mxc_nand: fix unbalanced clk_disable() in error path
mtd: nandsim: Introduce debugfs infrastructure
mtd: physmap_of: error checking to prevent a NULL pointer dereference
mtg: docg3: potential divide by zero in doc_write_oob()
mtd: bcm47xxnflash: writing support
mtd: tests/read: initialize buffer for whole next page
mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
mtd: nand: onfi need to be probed in 8 bits mode
mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
mtd: nand: print flash size during detection
mted: nand_wait_ready timeout fix
...
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The flctl can now be probed via device tree setup in addition to the
existing platform data way.
SoC specific setup data is set in the .data member of the OF match, so
kept within the driver itself, while board/user specific setup - like
partitioning - is taken from the device tree.
Actual configuration is added for the SoC sh7372.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The code probes if DMA channels can get allocated and tears them down at
removal/failure if needed.
If available it uses them to transfer the data part (not ECC). On
failure we fall back to PIO mode.
Based on Guennadi Liakhovetski's code from the sh_mmcif driver.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Some small fixes to avoid sparse and smatch complain. Other cosmetic fixes
as well.
- Change of the type of the member index in struct sh_flctl from signed
to unsigned. We use index by addressing array members, so unsigned is more
concise here. Adapt functions relying on sh_flctl::index.
- Remove a blurring cast in write_fiforeg().
- Apply consistent naming scheme when refering to the data buffer.
- Shorten some unnecessarily verbose functions.
- Remove spaces at start of lines.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Modify the device PM QoS core code to support PM QoS flags requests.
First, add a new field of type struct pm_qos_flags called "flags"
to struct dev_pm_qos for representing the list of PM QoS flags
requests for the given device. Accordingly, add a new "type" field
to struct dev_pm_qos_request (along with an enum for representing
request types) and a new member called "flr" to its data union for
representig flags requests.
Second, modify dev_pm_qos_add_request(), dev_pm_qos_update_request(),
the internal routine apply_constraint() used by them and their
existing callers to cover flags requests as well as latency
requests. In particular, dev_pm_qos_add_request() gets a new
argument called "type" for specifying the type of a request to be
added.
Finally, introduce two routines, __dev_pm_qos_flags() and
dev_pm_qos_flags(), allowing their callers to check which PM QoS
flags have been requested for the given device (the caller is
supposed to pass the mask of flags to check as the routine's
second argument and examine its return value for the result).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: mark gross <markgross@thegnar.org>
Just as Artem suggested:
"Both UBI and JFFS2 are able to read verify what they wrote already.
There are also MTD tests which do this verification. So I think there
is no reason to keep this in the NAND layer, let alone wasting RAM in
the driver to support this feature. Besides, it does not work for sub-pages
and many drivers have it broken. It hurts more than it provides benefits."
So kill MTD_NAND_VERIFY_WRITE entirely.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Check the new oob_required flag and only copy the OOB data to the internal
buffer if needed.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Elements have been copied "manually" in a loop. Better use memcpy().
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is an implemention of hardware ECC write page function which may return an
error indication.
For instance, using Atmel HW PMECC to write one page into a nand flash, the hardware
engine will compute the BCH ecc code for this page. so we need read a the
status register to theck whether the ecc code is generated.
But we cannot assume the status register always can be ready, for example,
incorrect hardware configuration or hardware issue, in such case we need
write_page() to return a error code.
Since the definition of 'write_page' function in struct nand_ecc_ctrl is 'void'.
So this patch will:
1. add return 'int' value for 'write_page' function.
2. to be consitent, add return 'int' value for 'write_page_raw' fuctions too.
3. add code to test the return value, and if negative, indicate an
error happend when write page with ECC.
4. fix the compile warning in all impacted nand flash driver.
Note: I couldn't compile-test all of these easily, as some had ARCH dependencies.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In hardware ecc mode, the flctl now writes and reads the oob data
provided by the user. Additionally the ECC is now returned in normal
page reads, not only when using the explicit NAND_CMD_READOOB command.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are multiple reasons for a rewrite:
- a race exists: when _4ECCEND is set, _4ECCFA may become true too
meanwhile, which is lost and a non-correctable error is treated as
correctable.
- the ECC statistics don't get properly propagated to the base code.
- empty pages would get marked as corrupted
The rewrite resolves the issues and I hope it gives a more explicit
code flow structure.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When we use hardware ecc, the flctl is run in so-called "sector access
mode". We can bundle 4 sector accesses when using 2KiB page sizes to read
a whole page at once and speed up things.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As the equation mtd->writesize == eccsteps * eccsize holds, we can
simplify the code. The second loop of the 1st hunk is never entered,
so we delete it.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The flctl uses 10 bytes ECC data for every 512 bytes sector. This patch
makes the controller write all 40 bytes instead of 10 bytes only.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The flctl hardware has changed and a new OOB layout must be adapted for
2KiB page size NAND chips when using hardware ECC.
The related bit fields ECCPOS[0-2] are gone — the bits are marked as
reserved now in the datasheet. As there are no official users of the
hardware ECC so far, they are completely removed.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When the data transfer between the controller and the NAND chip fails,
we now get notified.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the unmapping for the error case and for the driver removal.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
New NAND controllers can perform read/write via HW engines which don't expose
OOB data in their DMA mode. To reflect this, we should rework the nand_chip /
nand_ecc_ctrl interfaces that assume that drivers will always read/write OOB
data in the nand_chip.oob_poi buffer. A better interface includes a boolean
argument that explicitly tells the callee when OOB data is requested by the
calling layer (for reading/writing to/from nand_chip.oob_poi).
This patch adds the 'oob_required' parameter to each relevant {read,write}_page
interface; all 'oob_required' parameters are left unused for now. The next
patch will set the parameter properly in the nand_base.c callers, and follow-up
patches will make use of 'oob_required' in some of the callee functions.
Note that currently, there is no harm in ignoring the 'oob_required' parameter
and *always* utilizing nand_chip.oob_poi, but there can be
performance/complexity/design benefits from avoiding filling oob_poi in the
common case. I will try to implement this for some drivers which can be ported
easily.
Note: I couldn't compile-test all of these easily, as some had ARCH
dependencies.
[dwmw2: Merge later 1/0 vs. true/false cleanup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ecc.read_page() method for nand drivers is changed to return the maximum
number of bitflips that were corrected on any one region covering an ecc step,
This patch doesn't change what the nand code returns to mtd.
This v2 includes the change to the fsl_ifc_nand driver requested by Scott¹.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040883.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by (freescale changes): Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Flash device drivers initialize 'ecc_strength' in struct mtd_info, which is the
maximum number of bit errors that can be corrected in one writesize region.
Drivers using the nand interface intitialize 'strength' in struct nand_ecc_ctrl,
which is the maximum number of bit errors that can be corrected in one ecc step.
Nand infrastructure code translates this to 'ecc_strength'.
Also for nand drivers, the nand infrastructure code sets ecc.strength for ecc
modes NAND_ECC_SOFT, NAND_ECC_SOFT_BCH, and NAND_ECC_NONE. It is set in the
driver for all other modes.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Geert Uytterhoeven