Currently, workaround for broken WD drives is applied always, slowing
down all drives. And it has a bug - it's not applied after resume.
Apply the workaround only if the error really appears
(SErr == 0x1000500). This allows unaffected drives to run at full speed
(provided that no affected drive is connected to the controller).
Also make sure the workaround is re-applied on resume.
Tested on VT6421.
As SCR registers access is known to cause problems on VT6420 (and I
don't have it to test), keep the workaround applied always on VT6420.
Unaffected drive (Hitachi HDS721680PLA380):
Before:
$ hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 160 MB in 3.01 seconds = 53.16 MB/sec
After:
$ hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 200 MB in 3.01 seconds = 66.47 MB/sec
Affected drive (WDC WD5003ABYX-18WERA0):
Before:
$ hdparm -t --direct /dev/sda
/dev/sda:
Timing O_DIRECT disk reads: 180 MB in 3.02 seconds = 59.51 MB/sec
After:
$ hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 156 MB in 3.03 seconds = 51.48 MB/sec
$ hdparm -t --direct /dev/sdb
/dev/sdb:
Timing O_DIRECT disk reads: 180 MB in 3.02 seconds = 59.64 MB/sec
The first hdparm is slower because of the error:
[ 50.408042] ata5: Incompatible drive: enabling workaround. This slows down transfer rate to ~60 MB/s
[ 50.728052] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 50.744834] ata5.00: configured for UDMA/133
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes host drivers to use CONFIG_PM_SLEEP instead of CONFIG_PM
where applicable. Benefits of this change:
* unused code is not being compiled in for CONFIG_PM=y, CONFIG_PM_SLEEP=n
and CONFIG_PM_RUNTIME=y configurations
* easier transition to use struct dev_pm_ops and SIMPLE_DEV_PM_OPS() in
the future
* more consistent code (there are host drivers which are using the correct
CONFIG_PM_SLEEP checks already)
The patch leaves the core libata code and ->port_[suspend,resume] support
in sata_[inic162x,nv,sil24].c alone for now.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: linux-ide@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Jeff moved on to a greener pasture.
s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
This patch converts the drivers in drivers/ata/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Mark Lord <kernel@teksavvy.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use normal debugging path for dynamic debug capability.
Convert dev_printk(KERN_DEBUG to dev_dbg(
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use a single mechanism to show driver version.
Reduces text a tiny bit too.
Remove uses of static int printed_version
Add and use ata_print_version(const struct device *, const char *ver)
and ata_print_version_once.
$ size drivers/ata/built-in.*
text data bss dec hex filename
544969 73893 116584 735446 b38d6 drivers/ata/built-in.allyesconfig.ata.o
543870 73893 116592 734355 b34ad drivers/ata/built-in.allyesconfig.print_once.o
141328 14689 4220 160237 271ed drivers/ata/built-in.defconfig.ata.o
141212 14689 4220 160121 27179 drivers/ata/built-in.defconfig.print_once.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Saves a bit of text as the call takes fewer args.
Coalesce a few formats.
Convert a few bare printks to pr_cont.
$ size drivers/ata/built-in.o*
text data bss dec hex filename
558429 73893 117864 750186 b726a drivers/ata/built-in.o.allyesconfig.new
559574 73893 117888 751355 b76fb drivers/ata/built-in.o.allyesconfig.old
149567 14689 4220 168476 2921c drivers/ata/built-in.o.defconfig.new
149851 14689 4220 168760 29338 drivers/ata/built-in.o.defconfig.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c30670 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efdc6 (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
vt6420 has the same FIFO overflow problem as vt6421 when combined with
certain devices. This patch applies the magic fix to vt6420 too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Martin Qvist <q@maq.dk>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add optional @ap argument to ata_wait_register() and replace msleep()
calls with ata_msleep() which take optional @ap in addition to the
duration. These will be used to implement EH exclusion.
This patch doesn't cause any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add Joseph Chan's explanation of the problem and workaround to the
VT6421 magic fix.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
vt6421 has problems talking to recent WD drives. It causes a lot of
transmission errors while high bandwidth transfer as reported in the
following bugzilla entry.
https://bugzilla.kernel.org/show_bug.cgi?id=15173
Joseph Chan provided the following fix. I don't have any idea what it
does but I can verify the issue is gone with the patch applied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Originally-from: Joseph Chan <JosephChan@via.com.tw>
Reported-by: Jorrit Tijben <sjorrit@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Separate out ata_pci_bmdma_prepare_host() and ata_pci_bmdma_init_one()
from their SFF counterparts. SFF ones no longer try to initialize
BMDMA or set PCI master.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Separate out BMDMA irq handler from SFF irq handler. The misnamed
host_intr() functions are renamed to ata_sff_port_intr() and
ata_bmdma_port_intr(). Common parts are factored into
__ata_sff_port_intr() and __ata_sff_interrupt() and used by sff and
bmdma interrupt routines.
All BMDMA drivers now use ata_bmdma_interrupt() or
ata_bmdma_port_intr() while all non-BMDMA SFF ones use
ata_sff_interrupt() or ata_sff_port_intr().
For now, ata_pci_sff_init_one() uses ata_bmdma_interrupt() as it's
used by both SFF and BMDMA drivers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_sff_irq_clear() is BMDMA specific. Rename it to
ata_bmdma_irq_clear(), move it to ata_bmdma_port_ops and make
->sff_irq_clear() optional.
Note: ata_bmdma_irq_clear() is actually only needed by ata_piix and
possibly by sata_sil. This should be moved to respective low
level drivers later.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When writing a disc on certain lite-on dvd-writers (also rebadged
as optiarc/LG/...) connected to a vt6420, the ATAPI CDB ends
up in the datastream and on the disc, causing silent corruption.
Delaying between sending the CDB and starting DMA seems to
prevent this.
I do not know if there are burners that do not suffer from
this, but the patch should be safe for those as well.
There are many reports of this issue, but AFAICT no solution was
found before. For example:
http://lkml.indiana.edu/hypermail/linux/kernel/0802.3/0561.html
Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Before only the timings for master were set. Datasheet can be found
here: ftp://ftp.vtbridge.org/Docs/Storage/DS_VT6421A_100_CCPL.PDF
Surprisingly, a slave drive works without this patch. According to the
datasheet, the controller by default derives the DMA mode from the
Set Features command issued to a drive. Not sure about the PIO
timings, though. The real problem is that the timings for the master
effectively are the ones tuned for the slave. If these support
different UDMA-settings, there is trouble, especially when the slave
supports a higher UDMA than the master.
Anyhow, using the same mechanism for both master and slave seems like
a good idea.
Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Just remove redundant device ID for VIA VT8261.
The device ID 0x9000 and 0x9040 are redundant (for VT8261).
The 0x9040 is reserved for other usage.
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
commit b9d5b89b48 (sata_via: fix support
for 5287) accidently (?) removed vt*_prepare_host error handling - restore it
catched by gcc:
drivers/ata/sata_via.c: In function 'svia_init_one':
drivers/ata/sata_via.c:567: warning: 'host' may be used uninitialized in this function
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
5287 used to be treated as vt6420 but it didn't work. It's new family
of controllers called vt8251 which hosts four SATA ports as M/S of the
two ATA ports. This configuration is rather peculiar in that although
the M/S devices are on the same port, each have its own SCR (or
equivalent link status/control) registers which screws up the
port-link-device hierarchy assumed by libata. Another controller
which falls into this category is ata_piix w/ SIDPR access.
libata now has facility to deal with this class of controllers named
slave_link. A low level driver for such controllers can just call
ata_slave_link_init() on the respective ports and libata will handle
all the difficult parts like following up with single SRST after
hardresetting both ports.
This patch creates new controller class vt8251, implements slave_link
aware init sequence and config space based SCR access for it and moves
5287 to the new class.
This patch is based on Joseph Chan's larger patch which was created
before slave_link was implemented in libata.
http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
VIA controllers clear DEVICE register when IEN changes. Make sure
DEVICE is updated along with CTL.
This change is separated from Joseph Chan's larger patch.
http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link. However, that assumption won't hold anymore with the scheduled
addition of slave link.
Make SCR access ops per-link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Previously, post-softreset readiness is waited as follows.
1. ata_sff_wait_after_reset() waits for 150ms and then for
ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.
2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff.
If not, continue to #3.
3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending
on devmask using ata_sff_wait_ready().
And for post-hardreset readiness,
1. ata_sff_wait_after_reset() waits for 150ms and then for
ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.
2. sata_sff_hardreset waits for device readiness using
ata_sff_wait_ready().
This patch merges and unifies post-reset readiness waits into
ata_sff_wait_ready() and ata_sff_wait_after_reset().
ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready(). If TF
status is 0xff, link status is unknown and the port is SATA, it will
continue polling till ATA_TMOUT_FF_WAIT.
ata_sff_wait_after_reset() is updated to perform the following steps.
1. waits for 150ms.
2. waits for dev0 readiness using ata_sff_wait_ready(). Note that
this is done regardless of devmask, as ata_sff_wait_ready() handles
0xff status correctly, this preserves the original behavior except
that it may wait longer after softreset if link is online but
status is 0xff. This behavior change is very unlikely to cause any
actual difference and is intended. It brings softreset behavior to
that of hardreset.
3. waits for dev1 readiness just the same way ata_bus_post_reset() did.
Now both soft and hard resets call ata_sff_wait_after_reset() after
reset to wait for readiness after resets. As
ata_sff_wait_after_reset() contains calls to ->sff_dev_select(),
explicit call near the end of sata_sff_hardreset() is removed.
This change makes reset implementation simpler and more consistent.
While at it, make the magical 150ms wait post-reset wait duration a
constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take
@link instead of @ap. This is to make them consistent with other
reset helpers and ease core changes.
pata_scc is updated accordingly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add sff_ prefix to SFF specific port ops.
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames ops and doesn't introduce any
behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SFF functions have confusing names. Some have sff prefix, some have
bmdma, some std, some pci and some none. Unify the naming by...
* SFF functions which are common to both BMDMA and non-BMDMA are
prefixed with ata_sff_.
* SFF functions which are specific to BMDMA are prefixed with
ata_bmdma_.
* SFF functions which are specific to PCI but apply to both BMDMA and
non-BMDMA are prefixed with ata_pci_sff_.
* SFF functions which are specific to PCI and BMDMA are prefixed with
ata_pci_bmdma_.
* Drop generic prefixes from LLD specific routines. For example,
bfin_std_dev_select -> bfin_dev_select.
The following renames are noteworthy.
ata_qc_issue_prot() -> ata_sff_qc_issue()
ata_pci_default_filter() -> ata_bmdma_mode_filter()
ata_dev_try_classify() -> ata_sff_dev_classify()
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames functions and doesn't
introduce any behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_chk_status() just calls ops->check_status and it only adds
confusion with other status functions. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently reset methods are not specified directly in the
ata_port_operations table. If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods. It's done this way for two reasons.
First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.
Second, as ->error_handler uses those reset methods, it can get
confusing. ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.
Now that ops table uses inheritance, the first problem doesn't exist
anymore. The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks. In fact, there currently is no driver which actually
modifies error handling behavior. Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH. I don't think making ops layering strict has
any noticeable benefit.
This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops. Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.
* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
aren't accessible. sata_promise doesn't need to use separate
error_handlers for PATA and SATA anymore.
* softreset is broken for sata_inic162x and sata_sx4. As libata now
always prefers hardreset, this doesn't really matter but the ops are
forced to NULL using ATA_OP_NULL for documentation purpose.
* pata_hpt374 needs to use different prereset for the first and second
PCI functions. This used to be done by branching from
hpt374_error_handler(). The proper way to do this is to use
separate ops and port_info tables for each function. Converted.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata lets low level drivers build ata_port_operations table and
register it with libata core layer. This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.
This becomes worse for drivers which support related similar
controllers which differ slightly. They share most of the operations
except for a few. However, the driver still needs to list all
operations for each variant. This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.
This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone. When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time. Some of those inconsistencies
cause immediate problems and fixed. Others just remain there dormant
making maintenance increasingly difficult.
To rectify the problem, this patch implements ata_port_operations
inheritance. To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance. An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop. When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified. This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.
libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma. To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.
After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to. The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.
* sata_sx4 is still using old style EH and currently doesn't take
advantage of ops inheritance.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata lets low level drivers build scsi_host_template and register it
to the SCSI layer. This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.
This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht. Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.
All sht tables are identical before and after this patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Over the time, port info, ops and sht structures developed quite a bit
of inconsistencies. This patch updates drivers.
* Enable/disable_pm callbacks added to all ahci ops tables.
* Every driver for SFF controllers now uses ata_sff_port_start()
instead of ata_port_start() unless the driver has custom
implementation.
* Every driver for SFF controllers now uses ata_pci_default_filter()
unless the driver has custom implementation.
* Removed an odd port_info->sht initialization from ata_piix.c.
Likely a merge byproduct.
* A port which has ATA_FLAG_SATA set doesn't need to set cable_detect
to ata_cable_sata(). Remove it from via and mv port ops.
* Some drivers had unnecessary .max_sectors initialization which is
ignored and was missing .slave_destroy callback. Fixed.
* Removed unnecessary sht initializations port_info's.
* Removed onsolete scsi device suspend/resume callbacks from
pata_bf54x.
* No reason to set ata_pci_default_filter() and bmdma functions for
PIO-only drivers. Remove those callbacks and replace
ata_bmdma_irq_clear with ata_noop_irq_clear.
* pata_platform sets port_start to ata_dummy_ret0. port_start can
just be set to NULL.
* sata_fsl supports NCQ but was missing qc_defer. Fixed.
* pata_rb600_cf implements dummy port_start. Removed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
When both soft and hard resets are available, libata preferred
softreset till now. The logic behind it was to be softer to devices;
however, this doesn't really help much. Rationales for the change:
* BIOS may freeze lock certain things during boot and softreset can't
unlock those. This by itself is okay but during operation PHY event
or other error conditions can trigger hardreset and the device may
end up with different configuration.
For example, after a hardreset, previously unlockable HPA can be
unlocked resulting in different device size and thus revalidation
failure. Similar condition can occur during or after resume.
* Certain ATAPI devices require hardreset to recover after certain
error conditions. On PATA, this is done by issuing the DEVICE RESET
command. On SATA, COMRESET has equivalent effect. The problem is
that DEVICE RESET needs its own execution protocol.
For SFF controllers with bare TF access, it can be easily
implemented but more advanced controllers (e.g. ahci and sata_sil24)
require specialized implementations. Simply using hardreset solves
the problem nicely.
* COMRESET initialization sequence is the norm in SATA land and many
SATA devices don't work properly if only SRST is used. For example,
some PMPs behave this way and libata works around by always issuing
hardreset if the host supports PMP.
Like the above example, libata has developed a number of mechanisms
aiming to promote softreset to hardreset if softreset is not going
to work. This approach is time consuming and error prone.
Also, note that, dependingon how you read the specs, it could be
argued that PMP fan-out ports require COMRESET to start operation.
In fact, all the PMPs on the market except one don't work properly
if COMRESET is not issued to fan-out ports after PMP reset.
* COMRESET is an integral part of SATA connection and any working
device should be able to handle COMRESET properly. After all, it's
the way to signal hardreset during reboot. This is the most used
and recommended (at least by the ahci spec) method of resetting
devices.
So, this patch makes libata prefer hardreset over softreset by making
the following changes.
* Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever
ATA_EH_{SOFT|HARD}RESET used to be used. ATA_EH_{SOFT|HARD}RESET is
now only used to tell prereset whether soft or hard reset will be
issued.
* Strip out now unneeded promote-to-hardreset logics from
ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and
other places.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Maybe for the trivial tree...
sata_via.c has PATA support since:
d73f30e1c9
sata_via: PATA support
AFAICS so the TODO list is no longer true.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SATA_PATA_SHARING register doesn't have anything to do with the
SATA part of the controller. It indicates whether an extern SATA PHY
is attached to the PATA part of the controller and if so how it is
wired. As the PATA part is driven by pata_via, sata_via has no reason
to care about that. Also, pata_via should work fine under all
configurations.
This patch removes unnecessary attach failures. It seems recent via
chipsets are defaulting to different values or are actually connected
to SATA PHY triggering this more often.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently, port configuration reporting has the following problems.
* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.
This patch implements and uses ata_port_desc() and
ata_port_pbar_desc(). ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ". ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.
LLD pushes whatever description it wants using the above two
functions. The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".
SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions. In many cases,
such controllers need to report different things anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.
* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I think that I've found and fixed the problem. There is a copy/paste bug in
vt6421_set_dma_mode() function which causes wrong values to be written to
PATA_UDMA_TIMING register.
This patch fixes a copy/paste bug that breaks DMA modes on VT6421 PATA port.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ondrej Zary