It is found on Dell Inspiron 1018 that the firmware reports that the hardware
killswitch is not supported. This makes the rfkill key not functional.
This patch forces the driver to toggle the firmware rfkill status in the case
that the hardware killswitch is indicated as unsupported by the firmware.
Signed-off-by: Keng-Yu Lin <keng-yu.lin@canonical.com>
Tested-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Some thinkpad hotkeys report key codes like KEY_FN_F8 when something
like KEY_VOLUMEDOWN is desired. Always provide the scan codes in
addition to the key codes to assist with debugging these issues. Also
send the scan code before the key code to match what other drivers do,
as some userspace utilities expect this ordering.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
6AF4F258-B401-42fd-BE91-3D4AC2D7C0D3 needs to be
6AF4F258-B401-42FD-BE91-3D4AC2D7C0D3 to match the hardware alias.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: stable@kernel.org
Most platform/x86 drivers that use INPUT_SPARSEKMAP also depend on INPUT,
so do the same for ideapad-laptop. This fixes a kconfig warning and
subsequent build errors when CONFIG_INPUT is disabled.
warning: (ACER_WMI && ASUS_LAPTOP && DELL_WMI && HP_WMI && PANASONIC_LAPTOP && IDEAPAD_LAPTOP && EEEPC_LAPTOP && EEEPC_WMI && MSI_WMI && TOPSTAR_LAPTOP && ACPI_TOSHIBA) selects INPUT_SPARSEKMAP which has unmet direct dependencies (!S390 && INPUT)
ERROR: "input_free_device" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "input_register_device" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "sparse_keymap_setup" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "input_allocate_device" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "input_unregister_device" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "sparse_keymap_free" [drivers/platform/x86/ideapad-laptop.ko] undefined!
ERROR: "sparse_keymap_report_event" [drivers/platform/x86/ideapad-laptop.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Don't allow everybody to change ACPI settings. The comment says that it
is done deliberatelly, however, the comment before disp_proc_write()
says that at least one of these setting is experimental.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
There is no need to install a chained handler for this hardware. This
is a plain x86 IOAPIC interrupt which is handled by the core code
perfectly fine. There is nothing special about demultiplexing these
gpio interrupts which justifies a custom hack. Replace it by a plain
old interrupt handler installed with request_irq. That makes the code
agnostic about the underlying primary interrupt hardware. The overhead
for this is minimal, but it gives us the advantage of accounting,
balancing and to detect interrupt storms. gpio interrupts are not
really that performance critical.
Patch fixups from akpm
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
LANMAN response length was changed to 16 bytes instead of 24 bytes.
Revert it back to 24 bytes.
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
CC: stable@kernel.org
Signed-off-by: Steve French <sfrench@us.ibm.com>
The lower filesystem may do some type of inode revalidation during a
getattr call. eCryptfs should take advantage of that by copying the
lower inode attributes to the eCryptfs inode after a call to
vfs_getattr() on the lower inode.
I originally wrote this fix while working on eCryptfs on nfsv3 support,
but discovered it also fixed an eCryptfs on ext4 nanosecond timestamp
bug that was reported.
https://bugs.launchpad.net/bugs/613873
Cc: <stable@kernel.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
read() calls against a file descriptor connected to a directory are
incorrectly returning EINVAL rather than EISDIR:
[EISDIR]
[XSI] [Option Start] The fildes argument refers to a directory and the
implementation does not allow the directory to be read using read()
or pread(). The readdir() function should be used instead. [Option End]
This occurs because we do not have a .read operation defined for
ecryptfs directories. Connect this up to generic_read_dir().
BugLink: http://bugs.launchpad.net/bugs/719691
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Documentation/DMA-API-HOWTO.txt states:
"DMA transfers need to be synced properly in order for
the cpu and device to see the most uptodate and correct
copy of the DMA buffer."
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported and found by Johannes Stezenbach:
rt2800{pci,usb} do not report the Michael MIC in RXed frames, but do check
the Michael MIC in hardware. Therefore we have to report to mac80211 that the
received frame does not include the Michael MIC.
https://bugzilla.kernel.org/show_bug.cgi?id=16608
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast channel change fixes:
a) Always set OFDM timings
b) Don't re-activate PHY
c) Enable only NF calibration, not AGC
https://bugzilla.kernel.org/show_bug.cgi?id=27382
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a bug that undo_retrans is incorrectly decremented when undo_marker is
not set or undo_retrans is already 0. This happens when sender receives
more DSACK ACKs than packets retransmitted during the current
undo phase. This may also happen when sender receives DSACK after
the undo operation is completed or cancelled.
Fix another bug that undo_retrans is incorrectly incremented when
sender retransmits an skb and tcp_skb_pcount(skb) > 1 (TSO). This case
is rare but not impossible.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcin Slusarz says:
> In arch/arm/kernel/kprobes-decode.c there's a function
> arm_kprobe_decode_insn which does:
>
> } else if ((insn & 0x0e000000) == 0x0c400000) {
> ...
>
> This is always false, so code below is dead.
> I found this bug by coccinelle (http://coccinelle.lip6.fr/).
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to noMMU to put tlb_flush() in asm/tlbflush.h - it's
part of the tlb shootdown interface. Move it to asm/tlb.h instead, as
per x86.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to delay freeing any mapped page on SMP and ARMv7 systems to
ensure that the data is not accessed by other CPUs, or is used for
speculative prefetch with ARMv7. This includes not only mapped pages
but also pages used for the page tables themselves.
This avoids races with the MMU/other CPUs accessing pages after they've
been freed but before we've invalidated the TLB.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When SMP_ON_UP is used and the spinlocks are inlined, we end up with
inline spinlocks in the exit code, with references from the SMP
alternatives section to the exit sections. This causes link time
errors. Avoid this by placing the exit sections in the init-discarded
region.
Cc: <stable@kernel.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure a predictable endian state when entering signal handlers. This
avoids programs which use SETEND to momentarily switch their endian
state from having their signal handlers entered with an unpredictable
endian state.
Cc: <stable@kernel.org>
Acked-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 18991197b4 added --build-id
linker option when toolchain supports it. ARM one does, but for some
reason places the section at 0 when linker script doesn't mention it
explicitly.
The 1e621a8e37 worked around the problem
removing this section from binary image with explicit objcopy options,
but it still exists in vmlinux, confusing tools like debuggers and perf.
This problem was discussed here:
http://lists.infradead.org/pipermail/linux-arm-kernel/2010-May/015994.htmlhttp://lists.infradead.org/pipermail/linux-arm-kernel/2010-May/015994.html
but the proposed changes to the linker script were substantial.
This patch simply places NOTES (36 bytes long, at least when compiled
with CodeSourcery toolchain) between data and bss, which seem to be
the right place (and suggested by the sample linker script in
include/asm-generic/vmlinux.lds.h).
It is enough to place it correctly in vmlinux (so debuggers are happy):
Section Headers:
[11] .data PROGBITS c07ce000 7ce000 020fc0 00 WA 0 0 32
[12] .notes NOTE c07eefc0 7eefc0 000024 00 AX 0 0 4
[13] .bss NOBITS c07ef000 7eefe4 01e628 00 WA 0 0 32
Program Headers:
LOAD 0x008000 0xc0008000 0xc0008000 0x7e6fe4 0x805628 RWE 0x8000
NOTE 0x7eefc0 0xc07eefc0 0xc07eefc0 0x00024 0x00024 R E 0x4
Section to Segment mapping:
Segment Sections...
00 <...> .data .notes .bss
01 .notes
and to get it exposed as /sys/kernel/notes used by perf tools.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SPEAR320_SOC_CONFIG_BASE was wrong, causing the wrong registers to be
accessed.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In sysctl_soft_reset(), switch to slow mode before resetting the system
via the system controller. This is required.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
readl() and writel() calls the outer cache maintainance operations
which are not available during Linux uncompression. This patch replaces
readl() and writel() with readl_relaxed() and writel_relaxed() to avoid
the link time errors.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes following warning:
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
by appending UL to VMALLOC_END's Number.
Reviewed-by: Stanley Miao <stanley.miao@windriver.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dependency is already expressed by the Makefiles, storing it in the
.cmd file breaks build if a .c file is replaced by .S or vice versa,
because the .cmd file contains
foo/bar.o: foo/bar.c ...
foo/bar.c ... :
so the foo/bar.c -> foo/bar.o rule triggers even if there is no
foo/bar.c anymore.
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michal Marek <mmarek@suse.cz>
VersaLogic Menlow based boards hang on reboot unless reboot=bios
is used. Add quirk to reboot through the BIOS.
Tested on at least four boards.
Signed-off-by: Kushal Koolwal <kushalkoolwal@gmail.com>
LKML-Reference: <1298152563-21594-1-git-send-email-kushalkoolwal@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
blk_throtl_exit assumes that ->queue_lock still exists,
so make sure that it does.
To do this, we stop redirecting ->queue_lock to conf->device_lock
and leave it pointing where it is initialised - __queue_lock.
As the blk_plug functions check the ->queue_lock is held, we now
take that spin_lock explicitly around the plug functions. We don't
need the locking, just the warning removal.
This is needed for any kernel with the blk_throtl code, which is
which is 2.6.37 and later.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
From: Eric W. Biederman <ebiederm@xmission.com>
In the beginning with batching unreg_list was a list that was used only
once in the lifetime of a network device (I think). Now we have calls
using the unreg_list that can happen multiple times in the life of a
network device like dev_deactivate and dev_close that are also using the
unreg_list. In addition in unregister_netdevice_queue we also do a
list_move because for devices like veth pairs it is possible that
unregister_netdevice_queue will be called multiple times.
So I think the change below to fix dev_deactivate which Eric D. missed
will fix this problem. Now to go test that.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: HDA: Do not announce false surround in Conexant auto
ALSA: HDA: Conexant auto: Handle multiple connections to ADC node
ALSA: HDA: Add position_fix quirk for an Asus device
ALSA: caiaq - Fix possible string-buffer overflow
ALSA: au88x0 - Modify pointer callback to give accurate playback position
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (lm85) extend to support EMC6D103 chips
MAINTAINERS: Remove stale hwmon quilt tree
hwmon: (k10temp) add support for AMD Family 12h/14h CPUs
hwmon: (jc42) do not allow writing to locked registers
hwmon: (jc42) more helpful documentation
hwmon: (jc42) fix type mismatch
This reverts commit 9b29050f8f.
It has caused hibernate regressions, for example Juri Sladby's report:
"I'm unable to hibernate 2.6.37.1 unless I rmmod tpm_tis:
[10974.074587] Suspending console(s) (use no_console_suspend to debug)
[10974.103073] tpm_tis 00:0c: Operation Timed out
[10974.103089] legacy_suspend(): pnp_bus_suspend+0x0/0xa0 returns -62
[10974.103095] PM: Device 00:0c failed to freeze: error -62"
and Rafael points out that some of the new conditionals in that commit
seem to make no sense. This commit needs more work and testing, let's
revert it for now.
Reported-by: Norbert Preining <preining@logic.at>
Reported-and-requested-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Cc: Guillaume Chazarain <guichaz@gmail.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no point in casting to (void *) when setting up xhci->ir_set
as it only makes us lose __iomem annotation and makes sparse unhappy.
OTOH we do need to cast to (void *) when calculating xhci->dba from
offset, but since it is IO memory we need to annotate it as such.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xhci->ir_set points to __iomem region, but xhci_print_ir_set accepts
plain struct xhci_intr_reg * causing multiple sparse warning at call
sites and inside the fucntion when we try to read that memory.
Instead of adding __iomem qualifier to the argument let's rework the
function so it itself gets needed register set from xhci and prints
it.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If the device isn't reset, the XHCI HCD sends
SET ADDRESS to address 0 while the device is
already in Addressed state, and the request is
dropped on the floor as it is addressed to the
default address. This sequence of events, which this
patch fixes looks like this:
usb_reset_and_verify_device()
hub_port_init()
hub_set_address()
SET_ADDRESS to 0 with 1
usb_get_device_descriptor(udev, 8)
usb_get_device_descriptor(udev, 18)
descriptors_changed() --> goto re_enumerate:
hub_port_logical_disconnect()
kick_khubd()
And then:
hub_events()
hub_port_connect_change()
usb_disconnect()
usb_disable_device()
new device struct
sets device state to Powered
choose_address()
hub_port_init() <-- no reset, but SET ADDRESS to 0 with 1, timeout!
The solution is to always reset the device in
hub_port_init() to put it in a known state.
Note from Sarah Sharp:
This patch should be queued for stable trees all the way back to 2.6.34,
since that was the first kernel that supported configured device reset.
The code this patch touches has been there since 2.6.32, but the bug
would never be hit before 2.6.34 because the xHCI driver would
completely reject an attempt to reset a configured device under xHCI.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
The expression
while (running_total < sg_dma_len(sg))
does not take into account that the remaining data length can be less
than sg_dma_len(sg). In that case, running_total can end up being
greater than the total data length, so an extra TRB is counted.
Changing the expression to
while (running_total < sg_dma_len(sg) && running_total < temp)
fixes that.
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Calculations like
running_total = TRB_MAX_BUFF_SIZE -
(sg_dma_address(sg) & (TRB_MAX_BUFF_SIZE - 1));
if (running_total != 0)
num_trbs++;
are incorrect, because running_total can never be zero, so the if()
expression will never be true. I think the intention was that
running_total be in the range of 0 to TRB_MAX_BUFF_SIZE-1, not 1
to TRB_MAX_BUFF_SIZE. So adding a
running_total &= TRB_MAX_BUFF_SIZE - 1;
fixes the problem.
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
This makes it easier to spot some problems, which will be fixed by the
next patch in the series. Also change dev_dbg to dev_err in
check_trb_math(), so any math errors will be visible even when running
with debug disabled.
Note: This patch changes the expressions containing
"((1 << TRB_MAX_BUFF_SHIFT) - 1)" to use the equivalent
"(TRB_MAX_BUFF_SIZE - 1)". No change in behavior is intended for
those expressions.
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Change the BUGs in xhci_find_new_dequeue_state() to WARN_ONs, to avoid
bringing down the box if one of them is hit
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Allow drivers to enable Zoomed Video support. Currently, this is only
used by out-of-tree drivers (L64020 DVB driver in particular).
CC: <stable@kernel.org> [for 2.6.37]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
When creating a new dentry we now hold a reference to the parent
inode in the ceph_dentry. This is required due to the new RCU
changes from 949854d0, which set dentry->d_parent to NULL in d_kill before
calling the ->release() callback. If/when that behavior is changed, we can
revert this hack.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
commit 5fa782c2f5 re-worked the
handling of unknown parameters. sctp_init_cause_fixed() can now
return -ENOSPC if there is not enough tailroom in the error
chunk skb. When this happens, the error header is not appended to
the error chunk. In that case, the payload of the unknown parameter
should not be appended either.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dcb_app protocol field is a __u32 however the 802.1Qaz
specification defines it as a 16 bit field. This patch brings
the structure inline with the spec making it a __u16.
CC: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman reported a lockdep splat in inet_twsk_deschedule()
This is caused by inet_twsk_purge(), run from process context,
and commit 575f4cd5a5 (net: Use rcu lookups in inet_twsk_purge.)
removed the BH disabling that was necessary.
Add the BH disabling but fine grained, right before calling
inet_twsk_deschedule(), instead of whole function.
With help from Linus Torvalds and Eric W. Biederman
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Daniel Lezcano <daniel.lezcano@free.fr>
CC: Pavel Emelyanov <xemul@openvz.org>
CC: Arnaldo Carvalho de Melo <acme@redhat.com>
CC: stable <stable@kernel.org> (# 2.6.33+)
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, one line-out and one speaker and
Conexant's auto parser would announce (non-working) surround
capabilities.
BugLink: http://bugs.launchpad.net/bugs/721126
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Conexant 20641 has several inputs to its ADC node, with one selector
and individual amps for all inputs. This patch adds support in the
Conexant auto parser to handle that case.
It also means that the pin node's volume is being renamed to "Boost"
to avoid name clash with the new volume controls on the ADC node.
BugLink: http://bugs.launchpad.net/bugs/719524
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If ID_MMFR0[3:0] >= 3, the architecture version is ARMv7. The code was
currently only testing for ID_MMFR0[3:0] == 3.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Keng-Yu Lin