This error was reported by cppcheck:
drivers/s390/net/smsgiucv.c:63: error: Using sizeof for array given as
function argument returns the size of pointer.
Although there is no runtime problem as long as sizeof(u8 *) == 8,
this misleading code should get fixed.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This error was reported by cppcheck:
drivers/s390/net/netiucv.c:568: error: Using sizeof for array given
as function argument returns the size of pointer.
sizeof(ipuser) did not result in 16 (as many programmers would have
expected) but sizeof(u8 *), so it is 4 or 8, too small here.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For OSA the CHPARM-definition determines the number of available
outbound queues.
A CHPARM-change may occur while a Linux system with probed
OSA device is in suspend state. This patch enables proper
resuming of an OSA device in this case.
Signed-off-by: Ursula braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For HiperSockets the framesize-definition determines the selected
mtu-size and the size of the allocated qdio buffers.
A framesize-change may occur while a Linux system with probed
HiperSockets device is in suspend state. This patch enables proper
resuming of a HiperSockets device in this case.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HiperSockets and OSA hardware report a maximum MTU size. Add checking
to reject larger MTUs than allowed by hardware.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting of a MAC-address may fail because an already used MAC-address
is to bet set or because of authorization problems. In those cases
qeth issues a message, but the mentioned MAC-address is not the
new MAC-address to be set, but the actual MAC-address. This patch
chooses now the new MAC-address to be set for the error messages.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
sctp: user perfect name for Delayed SACK Timer option
net: fix can_checksum_protocol() arguments swap
Revert "netlink: test for all flags of the NLM_F_DUMP composite"
gianfar: Fix misleading indentation in startup_gfar()
net/irda/sh_irda: return to RX mode when TX error
net offloading: Do not mask out NETIF_F_HW_VLAN_TX for vlan.
USB CDC NCM: tx_fixup() race condition fix
ns83820: Avoid bad pointer deref in ns83820_init_one().
ipv6: Silence privacy extensions initialization
bnx2x: Update bnx2x version to 1.62.00-4
bnx2x: Fix AER setting for BCM57712
bnx2x: Fix BCM84823 LED behavior
bnx2x: Mark full duplex on some external PHYs
bnx2x: Fix BCM8073/BCM8727 microcode loading
bnx2x: LED fix for BCM8727 over BCM57712
bnx2x: Common init will be executed only once after POR
bnx2x: Swap BCM8073 PHY polarity if required
iwlwifi: fix valid chain reading from EEPROM
ath5k: fix locking in tx_complete_poll_work
ath9k_hw: do PA offset calibration only on longcal interval
...
Some OSA level have a bug in the hw tx csum logic. We can circumvent
this bug by turning on IP hw csum also.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The open function of qeth is not executed if the qeth device is in
state DOWN or HARDSETUP. A recovery switches from state SOFTSETUP to
HARDSETUP to DOWN to HARDSETUP and back to SOFTSETUP. If open and
recover are running concurrently, open fails if it hits the states
HARDSETUP or DOWN. This patch inserts waiting for recovery finish
in the qeth open functions to enable successful qeth device opening
in spite of a running recovery.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The used buffers counter is not incremented in case of an error so
the counter can become negative. Increment the used buffers counter
before checking for errors.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce a scan treshold for the qdio outbound queues. By setting the
threshold the driver can tell qdio after how much used SBALs qdio
should schedule the outbound tasklet that scans the queue for finished
SBALs. The threshold is specific by the drivers because a
Hipersockets device is much faster in utilizing outbound buffers than a
ZFCP or OSA device.
The default values after how many used SBALs the tasklet should run are:
OSA: > 31 SBALs
Hipersockets: > 7 SBALs
zfcp: > 55 SBALs
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for CTC I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for CLAW I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for LCS I/O interrupt statistics in /proc/interrupts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make use of def_bool and def_tristate where possible and add sensible
defaults to the config symbols where applicable. This shortens the
defconfig file by another ~40 lines.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
The used buffers counter is not incremented in case of an error so
the counter can become negative. Increment the used buffers counter
before checking for errors.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OSA l3 mode is hw accelerated VLAN only for IPv4. Take care we
add the vlan hdr to a passthru frame in the device driver.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only work through the IP adddress to do list if the card is UP or
SOFTSETUP. Enables to configure VIPA add/del in offline mode.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function qeth_l3_arp_query now queries for IPv6 addresses, too, if
QETH_QARP_WITH_IPV6 is passed as parameter to the ioctl. HiperSockets
and GuestLAN in HiperSockets mode provide corresponding entries.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tso hdr is longer then the regular l3 hdr. Fix the calculation
of the total len by accounting the size of the tso hdr.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device initialization of a qeth device contains a STARTLAN step.
This step may fail, if cable is not yet plugged in. The qeth device
stays in state HARDSETUP until cable is plugged in. This prevents
further preparational initialization steps of the qeth device and
its network interface. This patch makes sure initialization of qeth
device continues, even though cable is not yet plugged in.
Once carrier is available, qeth is notified, triggers a recovery
which results in a working network interface.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1d7138de87
igmp: RCU conversion of in_dev->mc_list
converted rwlock to RCU.
Update the s390 network drivers(qeth & lcs) code to adapt to this change.
V2 : Changes based on suggestions given by Eric Dumazet
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QDIO is running independent from netdevice state. We are not
allowed to schedule NAPI in case the netdevice is not open.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a certain Hipersockets specific error code in the xmit path, the
qeth driver tries to invoke dev_queue_xmit again.
Commit 79640a4ca6 introduces a busylock
causing locking problems in case of re-invoked dev_queue_xmit by qeth.
This patch removes the attempts to retry packet sending with
dev_queue_xmit from the qeth driver.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs.
Since vlan groups will soon be more of an implementation detail
for vlan devices, rename the constant to be descriptive of its
actual purpose.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adapts qeth to handle tagged frames with VLAN-ID 0 and
with or without priority information in the tag. It enables qeth to
receive priority-tagged frames on a base interface, for example from
z/OS, without configuring an additional VLAN interface.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds NAPI support to the qeth layer 2 and layer 3
discipline. It is important to understand that we can not enable/disable
IRQs as usual, we have to use the corresponding new QDIO interface.
Also to not overdraw the budget we have to stop and restart buffer
processing at any point during processing a bulk of QDIO buffers.
Having the driver NAPI enabled it is possible to turn on GRO for the
layer 3 discipline.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the claw code calls ccwgroup_remove_ccwdev(), we need to make sure
CCWGROUP is enabled when CLAW is enabled. Otherwise we hit fun undefined
references at build time:
ERROR: "ccwgroup_remove_ccwdev" [drivers/s390/net/claw.ko] undefined!
ERROR: "ccwgroup_probe_ccwdev" [drivers/s390/net/claw.ko] undefined!
ERROR: "ccwgroup_driver_register" [drivers/s390/net/claw.ko] undefined!
ERROR: "ccwgroup_driver_unregister" [drivers/s390/net/claw.ko] undefined!
ERROR: "ccwgroup_create_from_string" [drivers/s390/net/claw.ko] undefined!
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Format an ipv6 address using vsprintf extensions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
READ/WRITE seems to be a bit too generic for defines in a device
driver. Just rename them to CTCM_READ/CTCM_WRITE to avoid warnings.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
READ/WRITE seems to be a bit too generic for defines in a device driver.
Just rename them to READ_CHANNEL/WRITE_CHANNEL which should suffice.
Fixes this:
In file included from drivers/s390/net/claw.c:93:
drivers/s390/net/claw.h:78:1: warning: "WRITE" redefined
In file included from /home2/heicarst/linux-2.6/arch/s390/include/asm/debug.h:12,
from drivers/s390/net/claw.c:68:
include/linux/fs.h:156:1: warning: this is the location of the previous definition
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sender kernel parameter contains a z/VM user ID where
alphabetic characters must be specified in uppercase.
Allow users to specify lowercase characters and convert the
sender string to uppercase at module initialization.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Function qeth_l2_remove_device invokes qeth_l2_del_all_mc at the end.
This is needless, because it is already called in the offline function.
And even more this is invalid, because multicast addresses cannot be
removed in DOWN state. Thus this patch deletes invocation of
qeth_l2_del_all_mc in function qeth_l2_remove_device.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@
- to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+ to = memdup_user(from,size);
if (
- to==NULL
+ IS_ERR(to)
|| ...) {
<+... when != goto l1;
- -ENOMEM
+ PTR_ERR(to)
...+>
}
- if (copy_from_user(to, from, size) != 0) {
- <+... when != goto l2;
- -EFAULT
- ...+>
- }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reply callback functions in qeth should return zero if command
response consists of one part only, otherwise qeth continues
waiting for further parts of the command response.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a claw device, just 2 subchannels have to be grouped.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If qeth issues an ipa command, but for some reasons the response
never comes back, qeth reaches a timeout.
Reset the irq_pending flag of the write channel in timeout handling
code and trigger a recovery to avoid endless looping for the following
ipa command.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch serializes device removal and other sysfs-triggered
configurations by moving removal of sysfs-attributes to the beginning
of the remove functions. And it serializes online/offline setting
and discipline-switching (causing reestablishing of the net_device)
by making use of a new discipline mutex.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem that occurs when switching from layer 3 to layer 2
mode. Resetting this mac_bits makes sure that we retrieve our mac address from
the card, otherwise the interface simply would'nt work.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qeth IP address flag setting is possible when device is
offline. When setting device online afterwards the current set
IP addresses have to be correctly registered with the device
regarding the IP address takeover attribute.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For z/VM guest operating systems, OSX CHPIDs can only be used, if
LPAR and z/VM userID are explicitly authorized through the Service
Element. Issue a message if this SE-authorization is missing.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OSN devices use the same function level as OSD devices. This patch
adds OSN-devices to the initialization function for func_level.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning on memory debugging showed there could be page breaks in
hardware headers. OSA does not allow this so we had to add code
to bounce the header in case there is a page break. This patch also
fixes a problem in case the skb->data part of a fragmented skb
spreads multiple pages.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function qeth_free_buffer_pool is called _after_ the per-card
debug area has been released. This debug message is not all that
usefull anyway, and thus gets removed.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the qerr debug area. Most info that goes in here is logged
to the card's local debug area already, those duplicates are removed. All other
elements are moved to the card's local debug area.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the misc debug area. Instead of logging the entire skb
we just log a pointer to it into the card's local debug area in
qeth_core_get_next_skb. Other then that, this debug area is not used anywhere.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the sense debug area completely. Despite the name this
debug area makes no sense at all because it's unused completely. Ouch.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the qeth_trace debug area. All relevant data is logged into
either qeth_setup or into each card's own debug area. Superfluous information
(such as the card number when logging into the card's own debug area) is
removed without replacement.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a debug area for each qeth card. This debug area will replace
various other debug areas that are global for all cards handled by the device
driver. On crash dump analysis this makes life easier when trying to find out
what's going on with an interface. Also, the forest of debug areas for this
device driver is significantly cleared up.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch decouples qeth_dbf_longtext from qeth's static debug array. The
function only uses one member anyway.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If another smsgiucv_app device exists, suspend / resume fails with
iucv path list corruption, because the same iucv_path_connect is
called twice.
The patch introduces a flag to save connect status of the smsgiucv
path to make sure iucv_path_connect in smsg_pm_restore_thaw is
called only once.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
The qeth driver is enabled to support the new OSA CHPID types OSX
and OSM.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop cast on the result of kmalloc and similar functions.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
@@
- (T *)
(\(kmalloc\|kzalloc\|kcalloc\|kmem_cache_alloc\|kmem_cache_zalloc\|
kmem_cache_alloc_node\|kmalloc_node\|kzalloc_node\)(...))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove qdio API wrappers used by qeth and replace them by calling the
appropriate functions directly.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Synchronize access to the drivers configuration interface.
Also do not allow configuration changes during online/offline
transition.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
z/OS may activate Optimized Latency Mode (OLM) for a connection
through an OSA Express3 adapter, which reduces the number of
allowed concurrent connections, if adapter is used in shared mode.
Create a meaningful message, if activation of an OSA-connection fails
due to an active OLM-connection on the shared OSA-adapter.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OSA supports HW TX checksumming in layer 3 mode. Enable this
feature and remove software fallback used for TSO. Cleanup
checksum bits to indicate OSA can do checksumming only for
IPv4 TCP and UDP.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Adapt qeth l3 to:
commit c2e21293c0
(ipv6: convert addrconf list to hlist)
converted lst_next member of inet6_ifaddr struct to a hlist.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mlx4, using char * to store mc address in private structure instead.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (108 commits)
bridge: ensure to unlock in error path in br_multicast_query().
drivers/net/tulip/eeprom.c: fix bogus "(null)" in tulip init messages
sky2: Avoid rtnl_unlock without rtnl_lock
ipv6: Send netlink notification when DAD fails
drivers/net/tg3.c: change the field used with the TG3_FLAG_10_100_ONLY constant
ipconfig: Handle devices which take some time to come up.
mac80211: Fix memory leak in ieee80211_if_write()
mac80211: Fix (dynamic) power save entry
ipw2200: use kmalloc for large local variables
ath5k: read eeprom IQ calibration values correctly for G mode
ath5k: fix I/Q calibration (for real)
ath5k: fix TSF reset
ath5k: use fixed antenna for tx descriptors
libipw: split ieee->networks into small pieces
mac80211: Fix sta_mtx unlocking on insert STA failure path
rt2x00: remove KSEG1ADDR define from rt2x00soc.h
net: add ColdFire support to the smc91x driver
asix: fix setting mac address for AX88772
ipv6 ip6_tunnel: eliminate unused recursion field from ip6_tnl{}.
net: Fix dev_mc_add()
...
Deactivate inbound checksumming on HiperSocket is a valid but
dangerous optimization in case the frame is routed from an OSA
network to an HiperSockets network. To go for sure we change the
default to software checksumming.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on their definition in z/VM, virtual devices for z/VM
VSWITCH or GuestLAN must be configured either in layer2 or in
layer3 mode. If qeth detects a layer mismatch, device activation
fails. Trying to recover from this error cannot help; thus
scheduling a recovery should be avoided.
In addition, since recovery is forbidden during online setting of
a qeth device, existence of its network device is guaranteed for all
dev_close() calls in qeth. The corresponding checks can be removed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If HiperSockets Network Traffic Analyzer is switched off, but trace
disabling fails somehow, the qeth driver does not switch off its
promisc mode status. A following sniffer reactivation fails, since
qeth does not see a need to reenable tracing.
At the same time the code analyzing results of trace commands is
restructured.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dhcp frames are valid IPv4 packets so there is no need to send them
in pass thru mode. This allows dhcp packets to pass HiperSockets.
Also the dhcp release frame is send out correctly with this patch.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
provide qeth kmsg definitions to enable hash string generation for
kernel message created with dev_err().
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsgiucv_app driver registers a callback with the smsgiucv driver
to receive z/VM CP special messages (SMSG) starting with "APP".
When the callback is called for special messages, the driver creates
an uevent for the received message. The uevent consists of additional
environment data containing the message prefix ("APP"), message sender,
and message content.
udev rules can be used to trigger application specific actions through
matching the content or sender of the special message.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Declare the smsgiucv prefix char pointer as "const" and use
use const char pointers in callback functions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
zfcp and qeth are setting flags for the qdio-layer, but these flags
are not used in qdio. Patch removes the flag definitions from qdio
and their settings in zfcp and qeth.
Cc: Jan Glauber <jang@linux.vnet.ibm.com>
Cc: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch introduces three macros to work with uc list from net drivers.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set default BLKT values for new OSA/3 hardware.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a qeth device is set online, several initialisation steps are
performed. If a failure in one of these steps occurs, the qeth
device is reset into DOWN state. If due to the failure a qeth recovery
is scheduled and started in another thread, this might cause all kinds
of conflicts, even a kernel panic. The patch forbids scheduling of a
qeth recovery while online processing is performed till the card is in
state SOFTSETUP.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New feature to trace HiperSockets network traffic for debugging
purposes.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claw module cannot be loaded together with qeth, because "qeth" has
been errorneously used as root device name. It is changed into "claw".
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
"Definition" is misspelled "defintion" in several comments; this
patch fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add missing 'const' attribute to avoid the following compile warnings:
drivers/s390/net/ctcm_main.c: In function 'ctcm_init':
drivers/s390/net/ctcm_main.c:1864: warning: assignment from incompatible pointer type
drivers/s390/net/lcs.c: In function 'lcs_init_module':
drivers/s390/net/lcs.c:2468: warning: assignment from incompatible pointer type
drivers/s390/net/claw.c: In function 'claw_init':
drivers/s390/net/claw.c:3408: warning: assignment from incompatible pointer type
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Technically there is no need to set the card offline to change
RX checksumming. Get rid of this stupid limitation.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum TSO size OSA can handle is 15 * PAGE_SIZE. This
patch reduces gso_max_size to this value and adds some sanity
checks and statistics to the TSO implementation.
Since only layer 3 is able to do TSO move all TSO related functions
to the qeth_l3 module.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a qeth device online requires to call function
ccw_device_set_online() for read-, write-, and data-subchannel.
Failures should be detected immediately without an attempt to
invoke follow-on activity qeth_qdio_clear_card().,
In addition, ccw_device_set_online calls are consolidated in
qeth_core_main.c only.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EDDP code has been removed from qeth in 2009. This patch removes two
useless remaining EDDP-references.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Isolate data connection to a shared OSA card against other data
connections to the same OSA card. Connectivity between isolated
data connections sharing the same OSA card is therefore possible only
through external network gear (e.g. a router).
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx_bytes value must be updated by skb length before skb is freed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cu3088-driver used as common base for lcs- and ctcm-devices
makes it difficult to assign the appropriate driver to an lcs-device
or a ctcm-device. This patch eliminates the cu3088-driver and thus
the root device "cu3088". Path /sys/devices/cu3088 is replaced with
the pathes /sys/devices/lcs and /sys/devices/ctcm.
Patch is based on a proposal from Cornelia Huck.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State transition to DEV_STATE_STOPPED indicates all outstanding I/O has
finished. Add wait queue to wait for this state.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a suspended z/VM guest has been logged off before the resume the
'SET SMSG IUCV' CP command need to be repeated to reenable sending
message via SMSG. This fixes the following error:
HCPMFS057I H4214002 not receiving; SMSG off
Error: non-zero CP response for command 'SMSG H4214002 CMM SHRINK 5010': #57
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch updates misc percpu related symbols such that percpu
symbols are unique and don't clash with local symbols. This serves
two purposes of decreasing the possibility of global percpu symbol
collision and allowing dropping per_cpu__ prefix from percpu symbols.
* drivers/crypto/padlock-aes.c: s/last_cword/paes_last_cword/
* drivers/lguest/x86/core.c: s/last_cpu/lg_last_cpu/
* drivers/s390/net/netiucv.c: rename the variable used in a macro to
avoid clashing with percpu symbol
* arch/mn10300/kernel/kprobes.c: replace current_ prefix with cur_ for
static variables. Please note that percpu symbol current_kprobe
can't be changed as it's used by generic code.
Partly based on Rusty Russell's "alloc_percpu: rename percpu vars
which cause name clashes" patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Group device now cleanly reacts to failures during channel start and
implements a clean rollback.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The creation of a new lcs device requires a call to the function
ccw_device_set_online() for the read and the write channel. Failure
of either call should terminate the lcs device creation immediately
with return code -ENODEV.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timer_list structure in lcs_send_lancmd() is allocated on stack.
Initialization with init_timer() leads to above ODEBUG message.
Instead use init_timer_on_stack() which prevents above msg.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This string query operation was supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert qeth's
implementation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
Don't use kfree directly after device registration started.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If nothing has been written into the qeth sysfs-attribute layer2,
its value is "-1" meaning "not yet defined". But the value is
displayed as "1" meaning "layer2 selected". The patch changes the
reading of this "-1"-value to "-1" to make clear the layer2-attribute
has not yet been defined.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth displayed an entry in /proc/service_level even when no valid
MCL-string was available (the MCL info is blank). The change is to
create an entry in /proc/service_level only when MCL-string is
non-zero.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear separation of cast-type determination (send path) for layer-2
resp. layer-3. Allowing to have inline functions for qeth layer-
discipline.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the IP address list contains entries (not removed when the device was set
offline) this entries should be registered next time the device is brought online.
In the past this was done implicitly with the device open call but since we wait
in the set IPv4 IPA and the device open common code holds various locks this
does not work any longer.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qeth HiperSockets support now retries sending of packets when the
IBM System z signals a temporary resource shortage (e.g. target
buffer full). The packet is enqueued into the device queue.
After 3 times of unsuccessful send the packet is dropped.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the remaining occurences of raw return values to their
symbolic counterparts in ndo_start_xmit() functions that were missed by the
previous automatic conversion.
Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero
is changed to explicitly use NETDEV_TX_OK.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the remaining direct accesses to the driver_data pointer
with calls to the dev_get_drvdata() and dev_set_drvdata() functions.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (55 commits)
netxen: fix tx ring accounting
netxen: fix detection of cut-thru firmware mode
forcedeth: fix dma api mismatches
atm: sk_wmem_alloc initial value is one
net: correct off-by-one write allocations reports
via-velocity : fix no link detection on boot
Net / e100: Fix suspend of devices that cannot be power managed
TI DaVinci EMAC : Fix rmmod error
net: group address list and its count
ipv4: Fix fib_trie rebalancing, part 2
pkt_sched: Update drops stats in act_police
sky2: version 1.23
sky2: add GRO support
sky2: skb recycling
sky2: reduce default transmit ring
sky2: receive counter update
sky2: fix shutdown synchronization
sky2: PCI irq issues
sky2: more receive shutdown
sky2: turn off pause during shutdown
...
Manually fix trivial conflict in net/core/skbuff.c due to kmemcheck
This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 4 +-
drivers/net/e1000/e1000_main.c | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/mv643xx_eth.c | 2 +-
drivers/net/niu.c | 4 +-
drivers/net/virtio_net.c | 10 ++--
drivers/s390/net/qeth_l2_main.c | 2 +-
include/linux/netdevice.h | 17 +++--
net/core/dev.c | 130 ++++++++++++++++++--------------------
9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (64 commits)
debugfs: use specified mode to possibly mark files read/write only
debugfs: Fix terminology inconsistency of dir name to mount debugfs filesystem.
xen: remove driver_data direct access of struct device from more drivers
usb: gadget: at91_udc: remove driver_data direct access of struct device
uml: remove driver_data direct access of struct device
block/ps3: remove driver_data direct access of struct device
s390: remove driver_data direct access of struct device
parport: remove driver_data direct access of struct device
parisc: remove driver_data direct access of struct device
of_serial: remove driver_data direct access of struct device
mips: remove driver_data direct access of struct device
ipmi: remove driver_data direct access of struct device
infiniband: ehca: remove driver_data direct access of struct device
ibmvscsi: gadget: at91_udc: remove driver_data direct access of struct device
hvcs: remove driver_data direct access of struct device
xen block: remove driver_data direct access of struct device
thermal: remove driver_data direct access of struct device
scsi: remove driver_data direct access of struct device
pcmcia: remove driver_data direct access of struct device
PCIE: remove driver_data direct access of struct device
...
Manually fix up trivial conflicts due to different direct driver_data
direct access fixups in drivers/block/{ps3disk.c,ps3vram.c}
Create dummy iucv-device to get control when the system is suspended
and resumed. Server the smsg iucv path on suspend, reestablish the
path on resume.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Patch establishes a dummy netiucv device to make sure iucv is notified
about suspend/resume even if netiucv is the only loaded iucv-exploting
module without any real net_device defined.
The PM freeze callback closes all open netiucv connections. Thus the
corresponding iucv path is removed.
The PM thaw/restore callback re-opens previously closed netiucv
connections.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Thanks to Sebastian Ott <sebott@linux.vnet.ibm.com> for fixing a few
typos in my original version of this patch.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: linux390@de.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up s390 drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning an requeue/retransmit the skb.
- claw: impossible condition, simply remove it
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last two drivers that need skb->dst in their start_xmit() function
Tell dev_hard_start_xmit() to no release it by unsetting IFF_XMIT_DST_RELEASE
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Function qeth_clear_output_buffer for HiperSockets may not clear
all 16 SBALEs, but only the used ones. The error flag in SBALF15
has to be cleared in any case.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For HiperSocket devices receive-path checksumming is not required.
Thus NO_CHECKSUMMING is used as default for HiperSocket interfaces.
For layer3 devices configured with NO_CHECKSUMMING received skbs
should have set their ip_summed field to CHECKSUM_UNNECESSARY.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
z/VM Virtual Switch Port Isolation allows guests on a VLAN UNAWARE
virtual switch to be isolated from other guests on the VSWITCH.
(See z/VM Apars VM64281 and VM64463).
The Linux qeth driver is affected, because it has to handle new
error codes introduced with the z/VM VSWITCH Port Isolation support.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Channels are already removed when setting a ctcm-device offline.
Thus ctcm_remove_device must not refer to channel information.
Solution: delete channel information from the trace call in
ctcm_remove_device.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a qeth device is plugged off, setting the device online stops in
state HARDSETUP and a failure is reported to the base cio-layer
causing halt/clear to be invoked. Replugging the device again triggers
a qeth recovery without notification of the cio-layer. If a device
is ungrouped in this state, the qeth set_offline function is not
invoked, because the corresponding ccwgroup device is not in state
ONLINE. Then incoming traffic is still handled by the qdio layer
resulting in a crash in qeth_l<x>_qdio_input_handler, because (part
of) the qeth data structures for this device are already removed.
Solution: After replugging the device qeth recovery should lead to a
working net device. Thus a "LAN offline" result when setting a qeth
device online must not report a failure to the base cio-layer.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 64ef895798 ("qeth: remove EDDP")
removed the qeth_core_offl.[hc] files, but ended up doing so by just
patching them to zero size, rather than removing them properly.
Actually remove the files.
Reported-by: Andrew Price <andy@andrewprice.me.uk>
Cc: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (81 commits)
[S390] remove duplicated #includes
[S390] cpumask: use mm_cpumask() wrapper
[S390] cpumask: Use accessors code.
[S390] cpumask: prepare for iterators to only go to nr_cpu_ids/nr_cpumask_bits.
[S390] cpumask: remove cpu_coregroup_map
[S390] fix clock comparator save area usage
[S390] Add hwcap flag for the etf3 enhancement facility
[S390] Ensure that ipl panic notifier is called late.
[S390] fix dfp elf hwcap/facility bit detection
[S390] smp: perform initial cpu reset before starting a cpu
[S390] smp: fix memory leak on __cpu_up
[S390] ipl: Improve checking logic and remove switch defaults.
[S390] s390dbf: Remove needless check for NULL pointer.
[S390] s390dbf: Remove redundant initilizations.
[S390] use kzfree()
[S390] BUG to BUG_ON changes
[S390] zfcpdump: Prevent zcore from beeing built as a kernel module.
[S390] Use csum_partial in checksum.h
[S390] cleanup lowcore.h
[S390] eliminate ipl_device from lowcore
...
Errors from SIGA instructions are stored in the per queue qdio_error
and reported back when the queue handler is called. That opens a race
when multiple error conditions occur simultanously.
Report SIGA errors immediately in the return value of do_QDIO so the
upper layer can react and SIGA errors no longer interfere with other
errors.
Move the SIGA error handling in qeth from the outbound handler to
qeth_flush_buffers.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
wait_event_timeout just takes the numnber of jiffies to wait as
an argument. That value does not include jiffies itself.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a recovery is started for a qeth device, additional invocations
to change a mac address, to configure a VLAN interface on top, or to
add multicast addresses should wait till recovery is finished,
otherwise recovery might fail.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth: Unregister MAC addresses from device (layer 2) during
recovery cycle. When the device is set online the MAC
addresses are registered again on the device.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Weil