Uwe pointed out that my alarm based UIE emulation is not sufficient
to replace the older timer/polling based UIE emulation on devices
where there is no alarm irq. This causes rtc devices without alarms
to return -EINVAL to UIE ioctls. The fix is to re-instate the old
timer/polling method for devices without alarm irqs.
This patch reverts the following commits:
042620a018 - Remove UIE emulation
1daeddd596 - Cleanup removed UIE emulation declaration
b5cc8ca1c9 - Remove Kconfig symbol for UIE emulation
The emulation mode will still need to be wired-in with a following
patch before it will work.
CC: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
On hardware that doesn't support alarm interrupts, rtc_alarm_irq_enable
could return without releasing the ops_lock mutex.
This was introduced in
aa0be0f (RTC: Propagate error handling via rtc_timer_enqueue properly)
This patch corrects the issue by only returning once the mutex is
released.
[john.stultz: Reworded the commit log]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
* 'rtc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: Fix minor compile warning
RTC: Convert rtc drivers to use the alarm_irq_enable method
RTC: Fix rtc driver ioctl specific shortcutting
If we don't assign Moorestown specific wallclock init and ops function
the rtc/persisent clock code will use cmos rtc for access, this will
crash Moorestown in that the ioports are not present.
Also in vrtc driver, should avoid using cmos access to check UIP status.
[feng.tang@intel.com: use set_fixmap_offset_nocache() to simplify code]
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In file drivers/rtc/rtc-proc.c seq_open() can return -ENOMEM.
86 if (!try_module_get(THIS_MODULE))
87 return -ENODEV;
88
89 return single_open(file, rtc_proc_show, rtc);
In this case before exiting (line 89) from rtc_proc_open the
module_put(THIS_MODULE) must be called.
Found by Linux Device Drivers Verification Project
Signed-off-by: Alexander Strakh <strakh@ispras.ru>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some rtc drivers use the ioctl method instead of the alarm_irq_enable
method for enabling alarm interupts. With the new virtualized RTC
rework, its important for drivers to use the alarm_irq_enable instead.
This patch converts the drivers that use the AIE ioctl method to
use the alarm_irq_enable method. Other ioctl cmds are left untouched.
I have not been able to test or even compile most of these drivers.
Any help to make sure this change is correct would be appreciated!
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Reported-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Tested-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Some RTC drivers enable functionality directly via their ioctl method
instead of using the generic ioctl handling code. With the recent
virtualization of the RTC layer, its now important that the generic
layer always be used.
This patch moved the rtc driver ioctl method call to after the generic
ioctl processing is done. This allows hardware specific features or
ioctls to still function, while relying on the generic code for handling
everything else.
This patch on its own may more obviously break rtc drivers that
implement the alarm irq enablement via their ioctl method instead of
implementing the alarm_irq_eanble method. Those drivers will be fixed
in a following patch. Additionaly, those drivers are already likely to
not be functioning reliably without this patch.
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Tested-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This patch prevents a user space program from calling the RTC_IRQP_SET
ioctl with a negative value of frequency. Also, if this call is make
with a zero value of frequency, there would be a division by zero in the
kernel code.
[jstultz: Also initialize irq_freq to 1 to catch other divbyzero issues]
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The effect of changing the value of this symbol is gone since 042620a
(RTC: Remove UIE emulation).
Remove symbol too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
LKML-Reference: <1295625406-15340-1-git-send-email-u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In reviewing cases where the virtualized interfaces didn't propagate
errors properly, I noticed rtc_read_alarm needed fixing. In doing
so I noticed my RTC rework dropped a memset and that the behavior
of rtc_read_alarm shouldn't be conditionalized on the alarm.enabled
flag (as the alarm may be set, but the irqs may be disabled). So
those were corrected as well.
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
LKML-Reference: <1295565973-14358-2-git-send-email-john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In cases where RTC hardware does not support alarms, the virtualized
RTC interfaces did not have a way to propagate the error up to userland.
This patch extends rtc_timer_enqueue so it catches errors from the hardware
and returns them upwards to the virtualized interfaces. To simplify error
handling, it also internalizes the management of the timer->enabled bit
into rtc_timer_enqueue and rtc_timer_remove.
Also makes rtc_timer_enqueue and rtc_timer_remove static.
Reported-by: David Daney <ddaney@caviumnetworks.com>
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Diagnosed-by: David Daney <ddaney@caviumnetworks.com>
Tested-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
LKML-Reference: <1295565973-14358-1-git-send-email-john.stultz@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The first releases of LP3974 have a large delay in RTC registers,
which requires 2 seconds of delay after writing to a rtc register
(recommended by National Semiconductor's engineers)
before reading it.
If "rtc_delay" field of the platform data is true, the rtc driver
assumes that such delays are required. Although we have not seen
LP3974s without requiring such delays, we assume that such LP3974s
will be released soon (or they have done so already) and they are
supported by "lp3974" without setting "rtc_delay" at the platform
data.
This patch adds delays with msleep when writing values to RTC registers
if the platform data has rtc_delay set.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current implementation does not set driver data in max6902_probe(), thus
calling platform_get_drvdata(spi) in max6902_remove() returns NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc-cmos was setting suspend/resume hooks at the device_driver level.
However, the platform bus code (drivers/base/platform.c) only looks for
resume hooks at the dev_pm_ops level, or within the platform_driver.
Switch rtc_cmos to use dev_pm_ops so that suspend/resume code is executed
again.
Paul said:
: The user visible symptom in our (XO laptop) case was that rtcwake would
: fail to wake the laptop. The RTC alarm would expire, but the wakeup
: wasn't unmasked.
:
: As for severity, the impact may have been reduced because if I recall
: correctly, the bug only affected platforms with CONFIG_PNP disabled.
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@kernel.org> [2.6.37.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
request_mem_region() will call kzalloc to allocate memory for struct
resource. release_resource() unregisters the resource but does not free
the allocated memory, thus use release_mem_region() instead to fix the
memory leak.
Also add a missing iounmap() in omap_rtc_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (72 commits)
powerpc/pseries: Fix build of topology stuff without CONFIG_NUMA
powerpc/pseries: Fix VPHN build errors on non-SMP systems
powerpc/83xx: add mpc8308_p1m DMA controller device-tree node
powerpc/83xx: add DMA controller to mpc8308 device-tree node
powerpc/512x: try to free dma descriptors in case of allocation failure
powerpc/512x: add MPC8308 dma support
powerpc/512x: fix the hanged dma transfer issue
powerpc/512x: scatter/gather dma fix
powerpc/powermac: Make auto-loading of therm_pm72 possible
of/address: Use propper endianess in get_flags
powerpc/pci: Use printf extension %pR for struct resource
powerpc: Remove unnecessary casts of void ptr
powerpc: Disable VPHN polling during a suspend operation
powerpc/pseries: Poll VPA for topology changes and update NUMA maps
powerpc: iommu: Add device name to iommu error printks
powerpc: Record vma->phys_addr in ioremap()
powerpc: Update compat_arch_ptrace
powerpc: Fix PPC_PTRACE_SETHWDEBUG on PPC_BOOK3S
powerpc/time: printk time stamp init not correct
powerpc: Minor cleanups for machdep.h
...
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rtc: Namespace fixup
RTC: Remove UIE emulation
RTC: Rework RTC code to use timerqueue for events
Fix up trivial conflict in drivers/rtc/rtc-dev.c
Helper functions for I2C and SMBus transactions don't modify the
i2c_client that is passed to them, so it can be marked const.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (416 commits)
ARM: DMA: add support for DMA debugging
ARM: PL011: add DMA burst threshold support for ST variants
ARM: PL011: Add support for transmit DMA
ARM: PL011: Ensure IRQs are disabled in UART interrupt handler
ARM: PL011: Separate hardware FIFO size from TTY FIFO size
ARM: PL011: Allow better handling of vendor data
ARM: PL011: Ensure error flags are clear at startup
ARM: PL011: include revision number in boot-time port printk
ARM: vexpress: add sched_clock() for Versatile Express
ARM i.MX53: Make MX53 EVK bootable
ARM i.MX53: Some bug fix about MX53 MSL code
ARM: 6607/1: sa1100: Update platform device registration
ARM: 6606/1: sa1100: Fix platform device registration
ARM i.MX51: rename IPU irqs
ARM i.MX51: Add ipu clock support
ARM: imx/mx27_3ds: Add PMIC support
ARM: DMA: Replace page_to_dma()/dma_to_page() with pfn_to_dma()/dma_to_pfn()
mx51: fix usb clock support
MX51: Add support for usb host 2
arch/arm/plat-mxc/ehci.c: fix errors/typos
...
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, earlyprintk: Move mrst early console to platform/ and fix a typo
x86, apbt: Setup affinity for apb timers acting as per-cpu timer
ce4100: Add errata fixes for UART on CE4100
x86: platform: Move iris to x86/platform where it belongs
x86, mrst: Check platform_device_register() return code
x86/platform: Add Eurobraille/Iris power off support
x86, mrst: Add explanation for using 1960 as the year offset for vrtc
x86, mrst: Fix dependencies of "select INTEL_SCU_IPC"
x86, mrst: The shutdown for MRST requires the SCU IPC mechanism
x86: Ce4100: Add reboot_fixup() for CE4100
ce4100: Add PCI register emulation for CE4100
x86: Add CE4100 platform support
x86: mrst: Set vRTC's IRQ to level trigger type
x86: mrst: Add audio driver bindings
rtc: Add drivers/rtc/rtc-mrst.c
x86: mrst: Add vrtc driver which serves as a wall clock device
x86: mrst: Add Moorestown specific reboot/shutdown support
x86: mrst: Parse SFI timer table for all timer configs
x86/mrst: Add SFI platform device parsing code
flush_scheduled_work() is deprecated and scheduled to be removed. On
removal, directly cancel the work, and flush the uie_task in
rtc-dev.c::clear_uie().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux@googlegroups.com
Match the buffer size to the amount of initialized values. Before, it was
one too big and thus destroyed the neighbouring register causing the clock
to run at false speeds.
Reported-by: Andre van Rooyen <a.v.rooyen@sercom.nl>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch uses the RTC framework to treat some common ioctl.
In particular, it fixes the behaviour of rtc_irq_set_freq(), which did
not work as expected because the timer was not beeing retriggered.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
rtctimer_* is already occupied by sound/core/rtctimer.c. Instead of
fiddling with that, rename the new functions to rtc_timer_* which
reads nicer anyway.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <johnstul@us.ibm.com>
Since we provide UIE interrupts via a rtc_timer, the old
emulation code can be removed.
Signed-off-by: John Stultz <john.stultz@linaro.org>
LKML Reference: <1290136329-18291-5-git-send-email-john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Richard Cochran <richardcochran@gmail.com>
This patch reworks a large portion of the generic RTC code
to in-effect virtualize the rtc interrupt code.
The current RTC interface is very much a raw hardware interface.
Via the proc, /dev/, or sysfs interfaces, applciations can set
the hardware to trigger interrupts in one of three modes:
AIE: Alarm interrupt
UIE: Update interrupt (ie: once per second)
PIE: Periodic interrupt (sub-second irqs)
The problem with this interface is that it limits the RTC hardware
so it can only be used by one application at a time.
The purpose of this patch is to extend the RTC code so that we can
multiplex multiple applications event needs onto a single RTC device.
This is done by utilizing the timerqueue infrastructure to manage
a list of events, which cause the RTC hardware to be programmed
to fire an interrupt for the next event in the list.
In order to preserve the functionality of the exsting proc,/dev/ and
sysfs interfaces, we emulate the different interrupt modes as follows:
AIE: We create a rtc_timer dedicated to AIE mode interrupts. There is
only one per device, so we don't change existing interface semantics.
UIE: Again, a dedicated rtc_timer, set for periodic mode, is used
to emulate UIE interrupts. Again, only one per device.
PIE: Since PIE mode interrupts fire faster then the RTC's clock read
granularity, we emulate PIE mode interrupts using a hrtimer. Again,
one per device.
With this patch, the rtctest.c application in Documentation/rtc.txt
passes fine on x86 hardware. However, there may very well still be
bugs, so greatly I'd appreciate any feedback or testing!
Signed-off-by: John Stultz <john.stultz@linaro.org>
LKML Reference: <1290136329-18291-4-git-send-email-john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Richard Cochran <richardcochran@gmail.com>
The following warning is seen while compilation of PowerPC kernel:
CC drivers/rtc/rtc-cmos.o
drivers/rtc/rtc-cmos.c:697:2: warning: #warning Assuming 128 bytes
of RTC+NVRAM address space, not 64 bytes.
Fix it by adding defined(__powerpc__).
Signed-off-by: Srikanth Krishnakar <skrishna@mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Explain the reason for the apparently odd choice of year offset so we don't
get more questions about it.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
LKML-Reference: <20101117121050.9998.89348.stgit@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Provide the standard kernel rtc driver interface on top of the vrtc layer
added in the previous patch.
Signed-off-by: Feng Tang <feng.tang@intel.com>
LKML-Reference: <20101110172911.3311.20593.stgit@localhost.localdomain>
[Fixed swapped arguments on IPC]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
[Cleaned up and the device creation moved to arch/x86/platform]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes a nasty initialization condition on the RTSR register.
Sometimes, bit 1 will wake up set, sometimes not. This can be seen
by checking the value of the RTSR by typing '$ cat /proc/driver/rtc',
which has been provided by the previous patch.
If this bit is set, the command '$ cat /dev/rtc0' will lock the system
in an endless interrupt routine calling loop.
This patch fixes the issue both at sa1100_rtc_probe(), where it avoids
a spurious interrupt from happening, and at sa1100_rtc_interrupt(),
which is the robust solution, though it does not avoid the first
spurious interrupt.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a line to the output of /proc/drivers/rtc to show
the value of the RTSR register. It will be used to demonstrate
a nasty initialization bug that will be fixed in the sequence.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes checkpatch.pl issues in drivers/rtc/rtc-sa1100.c,
which I will later modify.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
request_mem_region() will call kzalloc to allocate memory for struct resource.
release_resource() unregisters the resource but does not free the allocated
memory, thus use release_mem_region() instead to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Only the secureedge5410 was ever supported by this code, so make the
board specification explicit rather than perpetuating a mach group.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The mfd driver for MC13783 recently got support for MC13892 and was
renamed accordingly from mc13783-core to mc13xxx-core. Do the same for
rtc-mc13783.
The only relevant change is to use platform id's to tell the platform bus
that this driver is responsible for mc13892-rtc devices, too.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes the ab8500 mixed signal chip expose the same
interface for register access as the ab3100, ab3550 and ab5500 chip.
The ab8500_read() and ab8500_write() is removed and replaced with
abx500_get_register_interruptible() and
abx500_set_register_interruptible().
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for the RTC provided by the Maxim 8998 chip. This
driver was tested on a GONI board by using the rtc-test application from
the Documentation/rtc.txt.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add the "alarm" function to the jz4740 RTC. Interrupts will now be raised
when the "alarm" time is reached.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DS3232 RTC driver only has the tick function. Add an alarm function
so the driver is complete.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add "rtc_valid_tm" in s3c_rtc_gettime() as per Wan ZongShun's suggestion.
Suggested-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change RTC initialization method in probe(). The 'rtc_valid_tm(tm)' can
check whether RTC BCD is valid or not. And change the method of checking
because the previous method cannot validate RTC BCD registers properly.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alarm_irq_enable function should be implemented to support RTC alarm.
And fix tabs instead of white space around the proc field.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current s3c_rtc_getalarm() sets missing field of alarm time with 0xff.
But this value should be -1 according to drivers/rtc/interface.c.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
S3C2410_RTCCON of TYPE_S3C64XX RTC should be read/written by readw and
writew, because TYPE_S3C64XX RTC uses bit 8 and 9. And TYPE_S3C2410 RTC
also can access it by readw and writew.
[atul.dahiya@samsung.com: tested on smdk2416]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Tested-by: Atul Dahiya <atul.dahiya@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-omap driver currently hardcodes the RTC wakeup capability to be
"not capable". While this seems to be true for existing OMAP1 boards
which are not wired for this, the DA850/OMAP-L138 SoC, the RTC can always
be wake up source from its "deep sleep" mode.
This patch lets the wakeup capability be set from platform data and does
not override the setting from the driver. For DA850/OMAP-L138, this is
done from arch/arm/mach-davinci/devices-da8xx.c:da8xx_register_rtc()
Note that this patch does not change the behavior on any existing OMAP1
board since the platform device registration sets the wakeup capability to
0 by default.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If device_register() fails then call put_device(). See comment to
device_register.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rest of the driver had debug markings already. This also standardizes
the usage of "dev" a bit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By unifying the RTC_ISTAT clearing steps, we shrink the interrupt handler
and avoid multiple writes to the hardware registers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an RTC driver for the built-in RTC in the LPC32XX SoC. This patch
includes updates from the initial review comments and updates from the v3
review.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Durgesh Pattamatta <durgesh.pattamatta@nxp.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable built-in RTC IP in Kconfig and modify comments and help messages.
RTT as RTC is still available but should not be selected in common case.
Reported-by: Yegor Yefremov <yegor_sub1@visionsystems.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
block: autoconvert trivial BKL users to private mutex
drivers: autoconvert trivial BKL users to private mutex
ipmi: autoconvert trivial BKL users to private mutex
mac: autoconvert trivial BKL users to private mutex
mtd: autoconvert trivial BKL users to private mutex
scsi: autoconvert trivial BKL users to private mutex
Fix up trivial conflicts (due to addition of private mutex right next to
deletion of a version string) in drivers/char/pcmcia/cm40[04]0_cs.c
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
These drivers do not seem to be under active
maintainance from my brief investigation. Apologies
to those maintainers that I have missed.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This change resolves a problem about unbalanced calls of
enable_irq_wakeup() and disable_irq_wakeup() for alarm interrupt.
Bug reproduction:
root@eb600:~# echo 0 > /sys/class/rtc/rtc0/wakealarm
WARNING: at kernel/irq/manage.c:361 set_irq_wake+0x7c/0xe4()
Unbalanced IRQ 46 wake disable
Modules linked in:
[<c0025708>] (unwind_backtrace+0x0/0xd8) from [<c003358c>] (warn_slowpath_common+0x44/0x5c)
[<c003358c>] (warn_slowpath_common+0x44/0x5c) from [<c00335dc>] (warn_slowpath_fmt+0x24/0x30)
[<c00335dc>] (warn_slowpath_fmt+0x24/0x30) from [<c0058c20>] (set_irq_wake+0x7c/0xe4)
[<c0058c20>] (set_irq_wake+0x7c/0xe4) from [<c01b5e80>] (s3c_rtc_setalarm+0xa8/0xb8)
[<c01b5e80>] (s3c_rtc_setalarm+0xa8/0xb8) from [<c01b47a0>] (rtc_set_alarm+0x60/0x74)
[<c01b47a0>] (rtc_set_alarm+0x60/0x74) from [<c01b5a98>] (rtc_sysfs_set_wakealarm+0xc8/0xd8)
[<c01b5a98>] (rtc_sysfs_set_wakealarm+0xc8/0xd8) from [<c01891ec>] (dev_attr_store+0x20/0x24)
[<c01891ec>] (dev_attr_store+0x20/0x24) from [<c00be934>] (sysfs_write_file+0x104/0x13c)
[<c00be934>] (sysfs_write_file+0x104/0x13c) from [<c0080e7c>] (vfs_write+0xb0/0x158)
[<c0080e7c>] (vfs_write+0xb0/0x158) from [<c0080fcc>] (sys_write+0x3c/0x68)
[<c0080fcc>] (sys_write+0x3c/0x68) from [<c0020ec0>] (ret_fast_syscall+0x0/0x28)
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ben Dooks <ben@fluff.org.uk>
Cc: Atul Dahiya <atul.dahiya@samsung.com>
Cc: Taekgyun Ko <taeggyun.ko@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was a mistake to mark the PL031 IRQ as shared (for the U8500),
we misread the datasheet. Get rid of this.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b485fe5ea ("rtc/m41t80: use rtc_valid_tm() to check returned tm")
added rtc_valid_tm to m41t80_rtc_read_alarm() but it was wrong while the
t->time does not contain complete date/time.
This patch also fixes a warning:
warning: passing argument 1 of 'rtc_valid_tm' from incompatible pointer type
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Much (but not all) of the RTC state is kept in the RTC peripheral which
has its own power domain. Periodically (1 HZ), that state is synced from
one power domain to the other (peripheral->core). When we are resuming,
we need to wait for the sync to occur so that we don't get a mismatch of
reading undefined state in the rest of the driver.
Further, once the externally maintained bits have been synced back into
the core, we then need to restore the bits maintained in the core. In our
particular case, that is just the write completion interrupt bit.
If we don't do any of this, working with the RTC causes ~5 second delays
from time to time after waking up due to the write completion interrupt
never firing.
Reported-by: Michael Dean <mdean@aeronix.com>
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The int_clear helper takes a bitmask of interrupts to keep, not to
disable. When suspending without wakeup enabled, we want to disable
all interrupts, so use 0 (keep none) instead of -1 (keep all).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (226 commits)
ARM: 6323/1: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
ARM: 6324/1: cam60: move cam60_spi_devices to .init.data
ARM: 6322/1: imx/pca100: Fix name of spi platform data
ARM: 6321/1: fix syntax error in main Kconfig file
ARM: 6297/1: move U300 timer to dynamic clock lookup
ARM: 6296/1: clock U300 intcon and timer properly
ARM: 6295/1: fix U300 apb_pclk split
ARM: 6306/1: fix inverted MMC card detect in U300
ARM: 6299/1: errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID
ARM: 6294/1: etm: do a dummy read from OSSRR during initialization
ARM: 6292/1: coresight: add ETM management registers
ARM: 6288/1: ftrace: document mcount formats
ARM: 6287/1: ftrace: clean up mcount assembly indentation
ARM: 6286/1: fix Thumb-2 decompressor broken by "Auto calculate ZRELADDR"
ARM: 6281/1: video/imxfb.c: allow usage without BACKLIGHT_CLASS_DEVICE
ARM: 6280/1: imx: Fix build failure when including <mach/gpio.h> without <linux/spinlock.h>
ARM: S5PV210: Fix on missing s3c-sdhci card detection method for hsmmc3
ARM: S5P: Fix on missing S5P_DEV_FIMC in plat-s5p/Kconfig
ARM: S5PV210: Override FIMC driver name on Aquila board
ARM: S5PC100: enable FIMC on SMDKC100
...
Fix up conflicts in arch/arm/mach-{s5pc100,s5pv210}/cpu.c due to
different subsystem 'setname' calls, and trivial port types in
include/linux/serial_core.h
The Ricoh RP5C01 RTC contains 26 x 4 bits of NVRAM. Provide access to it
via a sysfs "nvram" attribute file.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because CONFIG_PM is a precondition to CONFIG_ACPI, the ifdef CONFIG_PM
within ifdef CONFIG_ACPI is redundant.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mask out PM flag when reading the hour, always set MIL bit when
writing the hour.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a driver for the DS3232 RTC chip via the I2C bus. Alarms are not
supported in this version of the driver.
[akpm@linux-foundation.org: fix Kconfig help text]
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Jingchang Lu <b22599@freescale.com>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch does two modifications:
(1) Adjust enable/disable IRQs location,enable it after rtc
registration and disable it prior to unregistration.
(2) Put 'platform_set_drvdata(pdev, nuc900_rtc)' in front of rtc
registration still be safety, though there is no need to do this, when
I move enable irq after rtc registration, I think still put
'platform_set_drvdata' before rtc registration that would be a good
habit.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make returning time checking function valid. In spite of using the
'rtc_valid_tm', nevertheless, the read time function omits its returning
value, that means the 'rtc_valid_tm' is useless here.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use rtc_valid_tm() to check the returned struct rtc_time *tm, to avoid
returning a wrong tm value.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use rtc_valid_tm to check the returned struct rtc_time *tm, to avoid
returning a wrong tm value.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use rtc_valid_tm() to check returning tm for max6900, it can avoid
returning wrong tm value.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use rtc_valid_tm() to check returned struct rtc_time *tm - it can avoid
returning wrong tm value.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver is based on code from Freescale which accompanies their i.MX25
PDK board, with some cleanup.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We shouldn't implement private ops->ioctl() unless absolutely necessary.
pxa series RTC driver's ioctl() is unnecessary, since RTC subsystem has
implement the ioctl() very well,so we can only use the API of
'.alarm_irq_enable' and '.update_irq_enable' to do enable irq action.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- add sanity check for alarm data in fm3130_probe
- fix fm3130_set_alarm.
According to the datasheet, setting match bit '0' indicates that the
corresponding alarm field will be used in the match process
- add operation alarm_irq_enable operation which is responsible for
handling RTC_AIE_ON, RTC_AIE_OFF ioctls
- remove clearing of AF bit after reading rtc/alarm control register:
according to datasheet this bit is cleared anyway when rtc/alarm control
register is read
[akpm@linux-foundation.org: make fm3130_alarm_irq_enable() static, fix comment layout]
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Sergey Lapin <slapin@ossfans.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a user application wants to set the rtc time, the RTC subsystem takes
advantage of 'rtc_valid_tm(tm)' to check 'rtc_time *tm' value validity, it
make sure the 'tm->tm_year' is larger than 70,so if '70< tm_year < 100',
the '(settm->tm_year - 100)' will be negative. ' Setting the negative
value to hardware register will be invalid, so I add the 'if' condition to
make sure set a valid value to register.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- add an mdelay(1) to the polling loop to cause less frequent access to
the hardware register.
- change the return value from ENODEV to EPERM if the loop timed out. I
think the 'Operation not permitted' description is more suitable for the
meaning of 'check_rtc_access_enable()' function, it just be used to
judge rtc access operation is permitted or not.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (150 commits)
MIPS: PowerTV: Separate PowerTV USB support from non-USB code
MIPS: strip the un-needed sections of vmlinuz
MIPS: Clean up the calculation of VMLINUZ_LOAD_ADDRESS
MIPS: Clean up arch/mips/boot/compressed/decompress.c
MIPS: Clean up arch/mips/boot/compressed/ld.script
MIPS: Unify the suffix of compressed vmlinux.bin
MIPS: PowerTV: Add Gaia platform definitions.
MIPS: BCM47xx: Fix nvram_getenv return value.
MIPS: Octeon: Allow more than 3.75GB of memory with PCIe
MIPS: Clean up notify_die() usage.
MIPS: Remove unused task_struct.trap_no field.
Documentation: Mention that KProbes is supported on MIPS
SAMPLES: kprobe_example: Make it print something on MIPS.
MIPS: kprobe: Add support.
MIPS: Add instrunction format for BREAK and SYSCALL
MIPS: kprobes: Define regs_return_value()
MIPS: Ritually kill stupid printk.
MIPS: Octeon: Disallow MSI-X interrupt and fall back to MSI interrupts.
MIPS: Octeon: Support 256 MSI on PCIe
MIPS: Decode core number for R2 CPUs.
...
John Stultz