There is a mistake in current uda134x_mute function: mute_reg has been
changed in line 162 or line 164, so uda134x_write should write
"mute_reg" but not "mute_reg & ~(1<<2)" to
UDA134X_DATA010.
Signed-off-by: Shine Liu <shinel@foxmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the strings related to capture in order to be
interpreted correctly by alsamixer and possible other
UI based mixer applications.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8993 analogue control is shared with other devices in the same
product line. Since this is a very substantial proportion of the
driver move the definitions of these controls into a new wm_hubs module
which allows them to be shared between the two.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There has been an ad1836 driver in sound/blackfin based on traditional alsa.
The new driver is based on asoc. The architecture of ad1836 codec driver is
very much like ad1938.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dynamically control and control only the needed output amplifier
muting/un-muting.
The original code was muting and un-muting the following output
amplifiers: Earpiece PreDrivL/R, CarkitL/R at the same time
regardless which pin is actually in use at the given moment.
Move these as separate PGA so only the needed amplifier will be touched.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the function dapm_dac_check_power() in
sound/soc/soc-dapm.c, dac power can't be on/off stand-alone without any
output widget as sink. And according to dapm_adc_check_power(), adc
power can't be on/off stand-alone without any input widget as source. So
we can't only define some stand-alone SND_SOC_DAPM_DAC/SND_SOC_DAPM_ADC
to hope their power can be managed dynamically.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Store the TDM slot width then if it's set use that rather than the
sample size to calculate BCLK. Leave imposing constraints to the
core (which should do this but doesn't yet) or machine driver.
Also allow 0 TDM slots to be configure (for use when disabling TDM).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Extend set_tdm_slot to allow the user to arbitrarily set the frame width
and active TX/RX slots.
Updates magician.c and wm9081.c for the new set_tdm_slot(). wm9081.c
still doesn't handle the slot_width override.
While being there, correct an incorrect use of SlotsPerFrm(7) use in
bitmask on pxa-ssp.c (SSCR0_SlotsPerFrm(x) is (((x) - 1) << 24)) ).
(this series is meant for Mark's for-2.6.32 branch)
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is a workaround for the problem of several subsequent control
statements not being applied correctly to the codec controller (modem).
In order to follow the hook switch state change from handset to handsfree
while
in full duplex mode, two consecutive +VLS control commands were sent to the
modem. The first one was M1 (microphone only), the seconds one was M1S1 (both
microphone and speaker). As there was no real modem handshaking procedure
implemented, neither in the codec nor in the machine driver part of the line
discipline, the modem was having the second command missed.
Since a possibility to switch to microphone only mode (and speaker only mode
as well) seams of no value, I have modified the code to issue single M1S1
command only for any of those cases.
Tested on my Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds debugging statement that can help in tracing
how the driver is trying to control the codec device.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8776 is a high performance, stereo audio CODEC with five channel
input selector. The WM8776 is ideal for surround sound processing
applications for home hi-fi, DVD-RW and other audio visual equipment.
This driver implements support for most WM8776 features - currently the
ADC automatic level control/limiter functionality is omitted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Power management for the cs4270 codec is currently implemented as part
of the i2c_driver struct. The disadvantage of doing it this way is that
the callbacks registered in the snd_soc_card struct are called _before_
the codec's callbacks.
That doesn't work, because the snd_soc_card callbacks will most likely
switch down the codec's power domains or pull the reset GPIOs, and
hence make the i2c communication bail out.
Fix this by binding the suspend and resume code to the
snd_soc_codec_device driver model and let the I2C functions only call
the SoC core function for resume and suspend, which do nothing currently
but will do later.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This converts all the Wolfson drivers using this format (the only devices
that do) except WM8753 to use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While writes tend to be able to use a fairly bus independant format to
do the writes reads are all bus specific. To allow us to factor out
this code include the bus type as a parameter when setting up the
cache.
Initially just use this to factor out hw_write_t for I2C.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This corrected patch adds machine independent line discipline code, prevoiusly
exsiting inside my Amstrad Delta ASoC machine dirver, to the Conexant CX20442
codec driver. The code can be used as a standalone line discipline, or as a
set of codec specific functions called from machine's line discipline
callbacks. Anyway, the line discipline itself must be registered by a machine
driver.
Applies on top of the followup to my initial driver version:
http://mailman.alsa-project.org/pipermail/alsa-devel/2009-July/019757.html
Suggested by ASoC manintainer Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
1. fix "line over 80 characters" checkpatch warnings
2. ‘DMA_nnBIT_MASK’ is deprecated, use DMA_BIT_MASK instead
3. fix typos
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch fixes some checkpatch identified issues and adds a comment about
line discipline interaction to my driver code, as requested by Mark on my
inital submission (thank you Mark for applying my imperfect patch anyway).
It also fixes MODULE_ALIAS mismatch as used in my machine driver.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAX9877 needs an address of start register when we write values to
registers through i2c_master_send(), but the code for this was missed in
max9877_write_regs().
If the value of control is 0 in the max9877_set_out_mode(), the value is
not increased to 1, but actually the value to write to the register
should be 1.
And the register bits for out_mode and osc_mode should be cleared before
writing.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for Conexant CX20442-11 voice modem codec, suitable
for use by the ASoC board driver for Amstrad E3 (Delta) videophone. Related
sound card driver will follow.
This codec is an optional part of the Conexant SmartV three chip modem design.
As such, documentation for its proprietary digital audio interface is not
available. However, on Amstrad Delta board, thanks to Mark Underwood who
created an initial, omap-alsa based sound driver a few years ago[1], the codec
has been discovered to be accessible not only from the modem side, but also
over the OMAP McBSP based CPU DAI. Thus, the driver can be used by any sound
card that can access the codec DAI directly. The DAI configuration parameters
(sample rate and format, number of channels) has been selected out empirically
for best user experience.
The codec analogue interface consists of two pairs of analogue I/O pins:
speakerphone interface or telephone handset/headset interface. Furthermore, it
seams to provide two operation modes for speakerphone I/O: standard and
advanced, with automatic gain control and echo cancelation. Even if the codec
control interface is unknown and not available, all those interfaces and modes
can be selected over the modem chip using V.253 commands. The driver is able
to issue necessary commands over a suitable hw_write function if provided by a
sound card driver. Otherwise, the codec can be controlled over the modem from
userspace while inactive.
Even if nothig is known about the codec internal power management
capabilities, DAPM widgets has been used to model the codec audio map.
Automatically performed powering up/down of those virtual widgets results in
corresponding V.253 commands being issued.
Some driver features/oddities may be board specific, but I have no way to
verify that with any board other than Amstrad Delta.
[1] http://www.earth.li/pipermail/e3-hacking/2006-April/000481.html
Created and tested against linux-2.6.31-rc3.
Applies and works with linux-omap-2.6 commit
7c5cb7862d32cb344be7831d466535d5255e35ac as well.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
PLL was not being enabled when it was not bypassed. This patch
enables the PLL when it is used. Additionally, it disables the PLL
when it is bypassed.
Without this patch, the audio on TI DM646x EVM and DM355 EVM
does not work properly. The bit clocks and the frame sync signals
from the codec are not correct and hence the playback/record are faster
than usual for most sample rates. The reason for this was that the PLL
was not enabled when it was not bypassed.
Tested on DM6467 EVM, playback tested on DM355 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The callback function to control register was used by whole controls in
MAX9877 driver, but this causes using many if statement for double
register control or invert.
So, the callback function for double register control is separate
differently, and the code for invert is added in the callback function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This corrects a bug with ADC Inversion Switch in wm8974 codec.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
GCC 4.4.0 doesn't appear to be able to spot that we don't apply any FLL
configuration if the output frequency is zero.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAX9877 combines a high-efficiency Class D audio power amplifier
with a stereo Class AB capacitor-less DirectDrive headphone amplifier.
The max9877_add_controls() is called to register the MAX9877 specific
controls on machine specific init() of the machine driver.
The datasheet for the MAX9877 can find at the following url:
http://datasheets.maxim-ic.com/en/ds/MAX9877.pdf
[Slight edit to sort the ALL_CODECS entries -- broonie.]
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Due to the flexibility of the WM9081 FLL this should never happen
in a real system.
Reported-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to use the best value we picked, not the last value we
looked at.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without MODULE_LICENCE("GPL"), when built as a module it will fail
to load because it uses other GPL symbols from kernel.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the last in-kernel direct usage of driver_data, replace it with
the proper dev_get/set_drvdata() calls.
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While the hardware is capable of some limited asynmmetric modes the
driver does not currently support those modes so tell applications
that only symmetric rates are available.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8993 is a highly integrated ultra-low power hi-fi CODEC designed
for portable devices such as multimedia phones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Note the slightly tricky cache usage in the volume update function due
to the requirement for a separate write for the VU bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TLV320AIC3x driver is currently the only user of the CODEC hw_read
operation and is jumping through some hoops in order to do so. In order
to support future refactoring to make the hw_read operation more usable
unwrap the usage in this driver to avoid its use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Nothing uses it and the existing hw_read operation needs to be
refectored so it's easier to remove it rather than work with it.
Support can be re-added if the code requires volatile registers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A lot of CODECs share the same register data formats and therefore
replicate the code to manage access to and caching of the register
map. In order to reduce code duplication centralised versions of
this code will be introduced with drivers able to configure the use
of the common code by calling the new snd_soc_codec_set_cache_io()
API call during startup.
As an initial user the 7 bit address/9 bit data format used by many
Wolfson devices is supported for write only CODECs and the drivers
with straightforward register cache implementations are converted to
use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Register cache space was not being allocated for the final register,
causing bugs when it was used. Allocate space for it.
Also ensure that the final register is displayed in sysfs.
[Commit message rewritten to document actual issue. -- broonie]
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add "set_tristate" callbacks for HiFi and Voice DAIs.
Machine drivers can enable and disable tristate for each
DAI with "snd_soc_dai_set_tristate" function.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The wrong register cache variable was being used to provide the size for
the memcpy(), resulting in a copy of only a void * of data.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
According to TRM, an external FET controlled by a 1.8V output signal
can be used to reduce the pop-noise heard when the audio amplifier is
switched on. It is suggested that GPIO6 of TWL4030 be used, but any
other gpio can be used instead. This is indicated in machine driver
with the following twl4030_setup_data members:
-hs_extmute. Set to 1 if board has support for EXTMUTE.
-set_hs_extmute. Set to a callback funcion to control an external gpio
line. Set to NULL if MUTE[GPIO6] pin is used.
Codec driver takes care of enabling and disabling this output during
the headset pop attenuation sequence.
Also add a delay to let VMID settle in ramp up sequence.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8523 is a high performance stereo DAC with integral charge
pump providing 2Vrms line driver outputs using a single 3.3V power
supply rail.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The device is a mono device but it can read two channel data and
many I2S controllers only understand 2 channels.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SoC dapm adds the suffix "Switch" to SND_SOC_DAPM_SWITCH controls,
removing word "Switch" from HandsfreeL/HandsfreeR widget name
for avoiding to duplicate it.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Event for voice sidetone was being interpreted as an
analog HiFi bypass event because VSTPGA register offset
is less than ARXR2_APGA_CTL offset. Reordering the
register checks allows to handle voice digital bypass
event properly.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
AVDAC clk priority allows to determine the path ADC must
be connected when the codec is in option2 and both HiFi
and Voice paths are enabled.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Voice interface of twl4030 codec supports: CBM_CFM and
CBS_CFS. It doesn't support CBS_CFM.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-By: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No need to define second copies of mode and format, they're declared
with exactly the same type at the head of the function and there's no
conflict in their use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add basic support for integration with the regulator API to WM8580.
Since the core cannot yet disable biases when the CODEC is idle we
simply request and enable the regulators for the entire time the
driver is active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch mostly follows commit 5998102b90
"ASoC: Refactor WM8731 device registration" to make UDA1380 use standard
device instantiation. Similarly, the I2C device registration temporarily
moves into the magician machine driver before it will find its final
resting place in the board file.
At the same time, platform specific configuration is moved to platform data
and common power/reset GPIO handling moves into the codec driver.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For best performance the DAC sloping stopband filter should be enabled
below 24kHz and not enabled above that so remove the user visible
control for this and do it autonomously in the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For best performance the DAC sloping stopband filter should be
enabled below 24kHz and not enabled above that so remove the
user visible control for this and do it autonomously in the
driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For best performance the DAC sloping stopband filter should be
enabled below 24kHz and not enabled above that so remove the
user visible control for this and do it autonomously in the
driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Blackfin submission was done as a patch against a different tree
and contained a duplicate hunk which will cause us to loose track of the
substream pointers when shutting down. Remove one of the duplicated
hunks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These are not supported since performance can not be guaranteed
when they are in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The WM8961 is a low power, high quality stereo CODEC designed for
portable digital applications with headphone and stereo class D speaker
drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some code analyzer software mistakenly gives
divide by 0 error messages for these lines.
This patch will end its confusion.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the (likely cut-n-paste) error by commit
16a30fbb0d, which causes the error below:
sound/soc/codecs/twl4030.c: In function 'twl4030_read_reg_cache':
sound/soc/codecs/twl4030.c:152: error: 'cache' undeclared (first use in this function)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes crash when shutting down.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In addition to the operating mode check, also check the
codec's interface format in case of four channel mode.
If the codec is not in TDM (DSP_A) mode, return with error.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the codec->reg_cache instead of the array directly
in twl4030_init_chip for setting the default values.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
McASP on DM646x can operate in DIT (S/PDIF) where no codec is needed.
This patch provides stub codec that can be used in these configurations.
On DM646x EVM the McASP1 is connected to the S/PDIF out.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Unsigned variables should use `%u' rather than `%d'.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DAPM switch for HeadsetL/R mute. Since all bits are are needed
for the HFL/R pop removal to work the switch is using the SW_SHADOW
no HW register for the HandsfreeL/R mute.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shadow, non HW register for dealing with the HandsfreeL/R
muting.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the HandsfreeL/R (IHFL/R) pop removal code from the DAPM_MUX_E
to a more appropriate DAPM_PGA_E widget.
Also fix the power-up sequence to match with the TRM.
The power-down sequence is not described in the TRM, so do it
in a way, which seams like the correct sequence.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fairly minor issues:
- Don't register the DAIs, it's not required for AC97 devices.
- Make unexported functions static.
- Wrap some excessively long lines.
- Undo tab/space breakage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8974 is a low power, high quality mono CODEC designed for portable
applications such as digital still cameras or digital voice recorders.
This driver was originally written by Graeme Gregory and Liam Girdwood
and has since been maintained by myself with some updates contributed by
Brett Saunders and Javier Martin.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that we always set a new sysclk when using the FLL in master mode
and pick out the correct value for the sample rate in hw_params().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM9081 is designed to provide high power output at low distortion
levels in space-constrained portable applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Give unique stream names for the two playback streams so
DAPM can figure out which codec_dai is in use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
twl4030_setup_data structure can be passed from platform drivers to
the codec via the snd_soc_device->codec_data pointer.
Currently the setup data has support for the Headset pop-removal
related configuration, which differs from board to board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds SND_SOC_DAPM_PGA_E to the headset path, which handles
the headset ramp up and down sequences needed for the pop noise
removal.
With this patch the order of the internal components in the twl4030
codec is turned on and off in a correct order.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Restructuring the twl4030 codec's DAPM routing to be able to handle the power
sequences correctly.
The twl4030 codec internal implementation have this order:
DAC -> Analog PGA -> Mixer/Mux
While the ASoC framework expects the following order:
DAC -> Mixer -> Analog PGA
This patch moves the Analog PGA handling from SND_SOC_DAPM_PGA to _MIXER and
adds two levels of mixer to handle the digital and analog loopback
functionality.
Now the analog loopback does not powers on any of the DACs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a control for selecting the codec operation mode. TWL4030 codec
has two modes:
- Option 1. Audio only (4 audio DACs)
- Option 2. Voice/Audio (2 audio DACs and voice ADC/DAC)
Control is restricted when a stream is ongoing, since codec's
operation mode cannot be changed on-the-fly.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujflausi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
AUXR is selected by bit 2 and not by bit 1 in the ANAMICR register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enable TWL4030 VTXL/VTXR and VRX digital filters for uplink
and downlink paths, respectively.
This patch also corrects voice 8/16kHz mode selection bit
(SEL_16K) of CODEC_MODE register.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM9712 can be configured by resistor strapping GPIO4 to behave like
the WM9713 and default to leaving the AC97 link disabled after cold
reset until a warm reset occurs. In this configuration we need to issue
a warm reset after cold to bring the link up so do so. The warm reset
will be harmless on systems that don't need it.
[Changelog rewritten to document the reasoning. -- broonie]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The inputs of the twl4030 codec can be mixed, so we will use the mixer
DAPM for the analog microphone registers(0x05, 0x06), but if we enable
more than one input at the same time, the input impedance of the input
amplifier will be reduced.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Copy-paste error: TWL4030_PRECKL_GAIN >> TWL4030_PRECKR_GAIN
It has not caused problems, since
TWL4030_PRECKL_GAIN == TWL4030_PRECKR_GAIN == 0x30
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the magic 0x80 value with a suitable macro definition.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the VIBRA output on TWL4030 codec.
The VIBRA output can be driven with audio data or with
local vibrator driver.
Add the needed DAPM elements and routes for the VIBRA output and
controls for the VIBRA driver configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add voice digital loopback (sidetone) to the twl4030
driver. It mixes voice uplink attenuated (by sidetone gain) with
voice downlink when the codec is working in option2 (voice/audio
mode).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds voice downlink analog bypass switch. It follows
the same approach as in other analog bypass switches.
DAC switch is moved from 'DAC Voice' to 'Analog Voice Playback Mixer',
that will also allow voice DAC to be powered in digital voice
loopback (sidetone).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mis-typing exist in dapm controller definitions and dapm route definitions,
so happen mis-matched error when snd_soc_dapm_add_routes().
Cc: stable@kernel.org
Signed-off-by: Jinyoung Park <parkjy@mtekvision.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com
The AC97 wire format is completely fixed so CODECs don't have any choice
about the formats they accept but controllers accept a variety of data
formats and render them down onto the bus. Have a shared define so all
the CODEC drivers will interoperate with any of our controller drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The gain control for earpiece amplifier uses 0dB ~ 12dB according to the
TRM, but the present code is implemented to -6dB ~ 6dB.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to check only if the WM8350 is master and only when starting
the stream so if either is not true then we can skip the check.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds a new control named 'Master Playback Switch' for cs4270
codecs. It is implemented using the new SOC_DOUBLE_EXT macro to catch
the put function and store the information about manually set mute
controls from userspace. When a manual mute is set, we don't want the
soc core to un-mute the outputs.
Renamed cs4270_mute() to cs4270_dai_mute() to avoid confusion.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The control modifies the MUTE register, hence the polarity must be
inverted.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's expected behaviour for the CODEC header to provide them but the
WM8350 doesn't due to having all the registers together under drivers/mfd.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DAPMs for VDL(Voice Down Link) path. To support VDL path, we have
to change DAPMs of outputs(Earpiece, PreDrive Left/Right, Headset
Left/Right, Carkit Left/Right) from mux to mixer.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Save a little extra power by enabling the DC servo offset correction
for the output channels only when the relevant channels are enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modify the default startup sequence in the chip to set the DC servo
dither level for optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CLK_DSP provides a master clock for the DAC and ADC related functionality
on the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add Voice DAI to support the PCM voice interface of the twl4030 codec.
The PCM voice interface can be used with 8-kHz(voice narrowband) or
16-kHz(voice wideband) sampling rates, and 16bits, and mono RX and mono
TX or stereo TX.
The PCM voice interface has two modes
- PCM mode1 : This uses the normal FS polarity and the rising edge of
the clock signal.
- PCM mode2 : This uses the FS polarity inverted and the falling edge
of the clock signal.
If the system master clock is not 26MHz or the twl4030 codec mode is not
option2, the voice PCM interface is not available.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I notice that the fixes were merged, minus one:
sound/soc/codecs/wm9705.c: At top level:
sound/soc/codecs/wm9705.c:445: warning: initialization from incompatible pointer type
so you might find this trivial patch useful.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The original implementation of the constraints were good against sane
applications.
If the opening sequence is:
stream1_open, stream1_hw_params, stream2_open, stream2_hw_params -> the
constraints are set correctly for stream2.
But if the sequence is:
stream1_open, stream2_open, stream2_hw_params, stream1_hw_params -> than stream2
would receive constraint rate = 0, sample_bits = 0, since the stream1 has not
yet called hw_params...
The command to trigger this event:
gst-launch-0.10 alsasrc device=hw:0 ! alsasink device=hw:0 sync=false
This patch does some 'black magic' in order to always set the correct
constraints and sets it only when it is needed for the other stream.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8960 is a low power, high quality stereo codec designed for
portable digital audio applications.
Stereo class D speaker drivers provide 1W per channel into 8W loads.
Guaranteed low leakage, excellent PSRR and pop/click suppression
mechanisms enable direct battery connection for the speaker supply.
The device also integrates a complete microphone interface and a stereo
headphone driver. External component requirements are drastically
reduced as no separate microphone, speaker or headphone amplifiers are
required. Advanced on-chip digital signal processing performs automatic
level control for the microphone or line input.
Stereo 24-bit sigma-delta ADCs and DACs are used with low power
over-sampling digital interpolation and decimation filters and a
flexible digital audio interface.
The master clock can be input directly or generated internally by an
onboard PLL, supporting most commonly-used clocking schemes.
This driver was originally written by Liam Girdwood, with substantial
subsequent additions and updates for feature completeness and changes in
the ASoC framework from me.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This ensures that we sync with the DAPM powerdown sequencing properly
and don't need to bounce the power on the voice DAC so often.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DSP_A interface format support by setting the LRP bit in
DSP mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8988 is a low power, high quality stereo CODEC designed for
portable digital audio applications.
The device integrates complete interfaces to 2 stereo headphone or line
out ports. External component requirements are drastically reduced as no
separate headphone amplifiers are required. Advanced on-chip digital
signal processing performs graphic equaliser, 3-D sound enhancement and
automatic level control for the microphone or line input.
The WM8988 can operate as a master or a slave, with various master clock
frequencies including 12 or 24MHz for USB devices, or standard 256fs
rates like 12.288MHz and 24.576MHz. Different audio sample rates such as
96kHz, 48kHz, 44.1kHz are generated directly from the master clock
without the need for an external PLL.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix for compillation error introduced by the constrain patch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ak4535_remove() from sound/soc/codecs/ak4535.c calls
i2c_unregister_device() with a possibly null pointer.
This bug was found by smatch (http://repo.or.cz/w/smatch.git/).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds the needed code to be able to use 96KHz playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without this the WM9705 driver fails badly when resuming.
Tested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In case of duplex mode (capture and playback at the same time), the second
stream has to have the same parameters (rate, sample size) as the already
running stream.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
TWL4030 supports 96KHz sample playback, but only playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is an AVDD supply as well, normally one or more of the other
upplies would be tied to it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The active discharge does not bring sufficient benefit to justify the
lengthy times involved so don't do that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC sound/soc/codecs/twl4030.o
sound/soc/codecs/twl4030.c:1400: warning: braces around scalar initializer
sound/soc/codecs/twl4030.c:1400: warning: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1401: error: field name not in record or union initializer
sound/soc/codecs/twl4030.c:1401: error: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1401: warning: initialization from incompatible pointer type
sound/soc/codecs/twl4030.c:1402: error: field name not in record or union initializer
sound/soc/codecs/twl4030.c:1402: error: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1402: warning: excess elements in scalar initializer
sound/soc/codecs/twl4030.c:1402: warning: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1403: error: field name not in record or union initializer
sound/soc/codecs/twl4030.c:1403: error: (near initialization for 'twl4030_dai.ops')
sound/soc/codecs/twl4030.c:1403: warning: excess elements in scalar initializer
sound/soc/codecs/twl4030.c:1403: warning: (near initialization for 'twl4030_dai.ops')
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The drivers are basically duplicating the same code over and over.
As snd_soc_cnew is going to be made static some time after the next
merge window, we might as well convert them now.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Refactor the WM8580 device registration to probe via standard I2C device
registration, registering the DAIs once the device has probed via I2C.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge Eric Maio's patch to merge snd_soc_dai_ops out of line. Fixed
merge issues and updated drivers, plus an issue with the ops for the two
s3c2443 AC97 DAIs having been merged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8400 is a highly integrated audio CODEC and power management unit
intended for mobile multimedia application. This driver supports the
primary audio CODEC features, including:
- 1W speaker driver
- Fully differential headphone output
- Up to 4 differential microphone inputs
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds a driver for the SPI connected AK4104 S/PDIF transmitter
device. Its features are fairly simple, but as there is need to set up
certain bits in the IEC958 information, this better goes into a real
driver.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Removes numbers from the list of features/limitations and makes it
reflect recent changes to the code.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Rob Maris <maris.rob@vdi.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enum type for selecting the desired ramp delay for the headset output.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Considering the fact that most cpu_dai or codec_dai are using a same
'snd_soc_dai_ops' for several similar interfaces, 'ops' would be better
made a pointer instead, to make sharing easier and code a bit cleaner.
The patch below is rather preliminary since the asoc tree is being
actively developed, and this touches almost every piece of code,
(and possibly many others in development need to be changed as
well). Building of all codecs are OK, yet to every SoC, I didn't test
that.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When setting WM8510_MCLKDIV the pll was turned off.
When setting pll frequency you got twice the expected freq, because
the code calculated with postscaler of 8, but the hardware divide by 4.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Only allow SND_SOC_DAIFMT_CBS_CFS for the playback DAI.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the UDA1380's interpolator or decimator are set to be clocked from
the WSPLL (which syncs to the WSI signal), the DAI link must be running
to change the interpolator/decimator registers (which include volume
controls and digital mute setting).
* Queue work in the alsa PCM_START .trigger to flush registers
as soon as the link is running. This replaces the .prepare
and .digital_mute callbacks.
* Use the SILENCE override instead of MTM for muting and remove
its alsa control to avoid confusion.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This removes a misspelled comment and got rid of superfluous switch
case.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added support for scenarios where the Cirrus CS4270 audio codec is slave
to the bitclk and lrclk. Mixed setups are unsupported.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sound/soc/codecs/wm8753.c: In function 'wm8753_probe':
sound/soc/codecs/wm8753.c:1577: error: implicit declaration of function 'wm8753_add_controls'
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will reduce the number of writes done on resume, allowing that to
complete faster (especially on systems with very slow I2C like the
current Samsung driver).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The base support for the only in-tree user, the GTA01, is out of tree
and will be updated separately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch should be pure code motion, separating that out from the
functional changes to move to new style device registration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This avoids temporarily enabling the ouput stages during startup which
can cause audible effets in the output stages.
Reported-by: Fredrik Redgård <rik@svep.se>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the digital loopback/bypass support for twl4030 codec.
The digital loopback will let the digimic0 (routed in the TX1 capture path
inside of TWL4030) data to be routed back to the RX2 playback path
(I2S stereo). It can also route the analog capture date routed through the
TX1 back to RX2.
Effectively the digital loopback is routing the audio from the TX1 capture path
to the RX2 playback path.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the WM8731 driver to use a more standard device registration
scheme where the device can be registered independantly of the ASoC
probe.
As a transition measure push the current manual code for registering
the WM8731 into the individual machine driver probes. This allows
separate patches to update the relevant architecture files with less
risk of merge issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a pure code motion patch intended to improve reviewability of a
following patch moving WM8731 to use more standard device registration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8731 bias level configuration function was written slightly
obscurely - streamline the code a little and refresh the comments.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
WM8753 uses a tricky way to switch DAIs "on the fly", for that it
registers 2 dummy DAIs and substitutes them depending on mixer control.
List element of registered dummy DAIs should be preserved to allow
unregistering of DAIs on module unload.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the CS4270 codec driver to allow applications to use the mixer to
control Digital Loopback, Soft Ramp, Zero Cross, Popguard, and Auto-Mute.
Soft Ramp, Zero Cross, and Auto-Mute are disabled by the driver when it first
initializes the hardware, but these features either don't work or interfere
with normal ALSA behavior. However, they can now be re-enabled by an
application if desired.
Remove CONFIG_SND_SOC_CS4270_HWMUTE and always allow ASoC to control the mute
bits. The driver previously and erroneously assumed that these bits
control only external muting circuitry, but they also control internal
muting circuitry, so they should always be used.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
TLV320AIC3X volume controls are logarithmic. Export their dB ranges.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a minor fix but helps to define dB ranges for volume controls.
Only DAC digital volume has full register value range from 0 to 127 but
ADC PGA gain and output stage volume controls don't.
For ADC PGA, maximum value is 119 and then it saturates to the same
gain value of 59.5 dB. For output stages, value 117 corresponds to -78.3 dB
and is muted for values 118 and above.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Function wm899x_outpga_put_volsw_vu misuses the kcontrol's private value
by still accessing it as bitfields even SOC_SINGLE_VALUE constructs it
as a pointer into struct soc_mixer_control after the commit
4eaa9819dc.
This is very similar fix than fix to TLV320AIC3X codec made by
Eero Nurkkala <ext-eero.nurkkala@nokia.com>. This fix is compile tested
only.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Function snd_soc_dapm_put_volsw_aic3x misuses the kcontrol's private value
by still accessing it as bitfields even SOC_SINGLE_VALUE constructs it
as a pointer into struct soc_mixer_control after the commit
4eaa9819dc.
This was causing arbitrary register writes when touching the controls
defined with SOC_DAPM_SINGLE_AIC3X.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch splits set_dai_fmt into three variants (single interface,
dual interface playback only, dual interface capture only) so that
data input and output formats can be configured separately for dual
interface setups.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without this fix driver switches to WSPLL in uda1380_pcm_prepare
even if SYSCLK was chosen (uda1380_pcm_prepare modifies UDA1380_CLK
register to disable R00_DAC_CLK before flushing reg cache)
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This just updates my email address on some drivers I'd forgotten in a
previous patch.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace printk calls with dev_xxx calls. Set the 'dev' field of the codec
and codec_dai structures so that these calls work.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix a oversight in the CS4270 codec driver that caused a build break.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Spruce up the documentation in the CS4270 codec. Use kerneldoc where
appropriate. Fix incorrect comments.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC codec drivers typically serve two masters: the I2C bus and ASoC itself.
When a codec driver registers with ASoC, a probe function is called. Most
codec drivers call ASoC first, and then register with the I2C bus in the ASoC
probe function.
However, in order to support multiple codecs on one board, it's easier if the
codec driver is probed via the I2C bus first. This is because the call to
i2c_add_driver() can result in the I2C probe function being called multiple
times - once for each codec. In the current design, the driver registers
once with ASoC, and in the ASoC probe function, it calls i2c_add_driver().
The results in the I2C probe function being called multiple times before the
driver can register with ASoC again.
The new design has the driver call i2c_add_driver() first. In the I2C probe
function, the driver registers with ASoC. This allows the ASoC probe function
to be called once per I2C device.
Also add code to check if the I2C probe function is called more than once,
since that is not supported with the current ASoC design.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the analog loopback/bypass support for twl4030 codec.
Details for the implementation:
It seams that the analog loopback needs the DAC powered on on the channel,
where the loopback is selected. The switch for the DACs has been moved from
the DAPM_DAC to the "Analog XX Playback Mixer". In this way the DAC will be
powered while the audio playback is used or/and the loopback is enabled for
the channel.
The twl4030 codec powering has been reworked. Now the codec will be powered as
long as it does not receives the SND_SOC_BIAS_OFF event. The exceptions are
when the given change in the registers needs the codec power down/up cycle in
order to take effect. Otherwise the codec is on.
When the codec enters to STANDBY state and none of the loopback paths are
enabled, than the amplifiers, which are no in the DAPM path are forced to turn
off and the PLL is disabled. When playback/capture starts the disabled gains
are restored and the PLL is enabled.
When one of the loopback enabled in STANDBY mode, the disabled gains are
restored and the PLL is enabled also.
In short: the codec always goes to the lowest power state based on the
bias_level and the bypass_state.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8753 driver multiplexes the DAI structures it exposes to the
outside world, leaving them uninitialised until the codec probes. Since
the DAI name is used during the registration and setup process provide a
dummy name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the twl4030_power_up and twl4030_power_down function
earlier to facilitate the analog bypass implementation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the power switches for the physical ADC and for the
amplifiers for the analog capture path to map more closely
the actual path inside of the codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Headset Left anti-pop and bias ramp does not need to be
enabled, if the headset is not in use.
Move the code to DAPM event handler for HeadsetL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge the codec up and down functions to a simple one.
Codec is powered down by default (reg_cache change).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The offset cancelation bit in ANAMICL register is self cleanig.
Make sure that the reg_cache holds the same value as the HW
register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Further improvements in the I2C initialization sequence of the CS4270 driver.
All ASoC initialization is now done in the I2C probe function.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensures that the DAI and socdev exported by the codec match up with
their exported prototype.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Kbuild ignores dependency from things that are themselves selected so
ASoC machine drivers need to ensure that the control bus is being built.
This also avoids issues where multiple buses are supported by a given
codec.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The CS4270 supports stand-alone mode, where the codec is not connect to the
I2C or SPI buses. Instead, input voltages configure the codec at power-on.
The CS4270 ASoC device driver has partial support for this mode, but the
code was never tested, and partial support doesn't help anyone. It also made
the rest of the code more complicated than necessary.
[Removed redundant CS4270 dependency on I2C -- broonie]
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes the acpture switch name so that it better reflects its
purpose.
Signed-off-by: Ian Molton <iann@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch takes fixes a number of bugs in the caching code used by
several ASoC codec drivers. Mostly off-by-one fixes.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM9713 driver does not support configuring the PLL output frequency
so the output frequency parameter is irrelevant. Allow users to set it
to zero by ignoring it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver adds support for the wm9705 ac97 codec. The driver supports
audio input and output.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Call the snd_soc_free_pcm and snd_soc_dapm_free when the
codec driver is unloaded.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many codec drivers were implementing cookie-cutter copies of the function
that adds kcontrols to the codec.
This patch moves this code to a common function snd_soc_add_controls() in
soc-core.c and updates all drivers using copies of this function to use the
new common version.
[Edited to raise priority of error log message and document parameters.
-- broonie]
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The soc_value_enum has been merged to soc_enum.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For codecs that have both SPI and I2C support we need to ensure that we
don't try to make the codec driver built in when I2C is modular since
that won't link. Do this by creating a helper variable which uses
conditional defaults to pick up the correct value for all combinations.
We don't need to do anything special for I2C-only codecs since a
conditional select passes on the full value for a tristate.
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert the bitfield coded enums to the new VALUE_ENUM type.
Remove the enum check, since the VALUE_ENUM type can handle
the bitfield coding and also handles the 'holes' in the bitfield.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds DAPM implementaion for the capture path
on twlx030.
TWL has two physical ADC and two digital microphone (stereo) connections.
The CPU interface has four microphone channels.
For simplicity the microphone channel paths are named as:
TX1 (Left/Right) - when using i2s mode, only the TX1 data is valid
TX2 (Left/Right)
Input routing (simplified version):
There is two levels of mux settings for TWL in input path:
Analog input mux:
ADCL <- {Off, Main mic, Headset mic, AUXL, Carkit mic}
ADCR <- {Off, Sub mic, AUXR}
Analog/Digital mux:
TX1 Analog mode:
TX1L <- ADCL
TX1R <- ADCR
TX1 Digital mode:
TX1L <- Digimic0 (Left)
TX1R <- Digimic0 (Right)
TX2 Analog mode:
TX2L <- ADCL
TX2R <- ADCR
TX2 Digital mode:
TX2L <- Digimic1 (Left)
TX2R <- Digimic1 (Right)
The patch provides the following user controls for the capture path:
Mux settings:
"TX1 Capture Route": {Analog, Digimic0}
"TX2 Capture Route": {Analog, Digimic1}
"Analog Left Capture Route": {Off, Main Mic, Headset Mic, AUXL, Carkit Mic}
"Analog Right Capture Route": {Off, Sub Mic, AUXR}
Volume/Gain controls:
"TX1 Digital Capture Volume": Stereo gain control for TX1 path
"TX2 Digital Capture Volume": Stereo gain control for TX2 path
"Analog Capture Volume": Stereo gain control for the analog path only
Important things for the board files:
Microphone bias:
"Mic Bias 1": Bias for Main mic or for digimic0 (analog or digital path)
"Mic Bias 2": Bias for Sub mic or for digimic1 (analog or digital path)
"Headset Mic Bias": Bias for Headset mic
When the routing configured correctly only the needed components will be
powered/enabled.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modify the enum filter to more generic that it will filter
out the enums with text "Invalid".
The enum filter also required for the capture path.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Thanks to Troy Kisky <troy.kisky@boundarydevices.com> for noticing.
- DSP_A format has 1-bit data delay which corresponds to SSM6202 submode 2
- DSP_B has 0-bit data delay which corresponds to submode 1
- Currently driver sets them opposite so swap the submode setting
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Shine Liu