emac_mdio_read_link() was not copying the requested phy settings
back into the emac driver's own phy api. This has caused a link
speed mismatch issue for the AR8035 as the emac driver kept
trying to connect with 10/100MBps on a 1GBit/s link.
This patch also unifies shared code between emac_setup_aneg()
and emac_mdio_setup_forced(). And furthermore it removes
a chunk of emac_mdio_init_phy(), that was copying the same
data into itself.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where the AR8035 PHY can't be
detected on an Cisco Meraki MR24, if the ethernet cable is
not connected on boot.
Russell Senior provided steps to reproduce the issue:
|Disconnect ethernet cable, apply power, wait until device has booted,
|plug in ethernet, check for interfaces, no eth0 is listed.
|
|This appears to be a problem during probing of the AR8035 Phy chip.
|When ethernet has no link, the phy detection fails, and eth0 is not
|created. Plugging ethernet later has no effect, because there is no
|interface as far as the kernel is concerned. The relevant part of
|the boot log looks like this:
|this is the failing case:
|
|[ 0.876611] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
|[ 0.882532] /plb/opb/ethernet@ef600c00: reset timeout
|[ 0.888546] /plb/opb/ethernet@ef600c00: can't find PHY!
|and the succeeding case:
|
|[ 0.876672] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
|[ 0.883952] eth0: EMAC-0 /plb/opb/ethernet@ef600c00, MAC 00:01:..
|[ 0.890822] eth0: found Atheros 8035 Gigabit Ethernet PHY (0x01)
Based on the comment and the commit message of
commit 23fbb5a87c ("emac: Fix EMAC soft reset on 460EX/GT").
This is because the AR8035 PHY doesn't provide the TX Clock,
if the ethernet cable is not attached. This causes the reset
to timeout and the PHY detection code in emac_init_phy() is
unable to detect the AR8035 PHY. As a result, the emac driver
bails out early and the user left with no ethernet.
In order to stay compatible with existing configurations, the driver
tries the current reset approach at first. Only if the first attempt
timed out, it does perform one more retry with the clock temporarily
switched to the internal source for just the duration of the reset.
LEDE-Bug: #687 <https://bugs.lede-project.org/index.php?do=details&task_id=687>
Cc: Chris Blake <chrisrblake93@gmail.com>
Reported-by: Russell Senior <russell@personaltelco.net>
Fixes: 23fbb5a87c ("emac: Fix EMAC soft reset on 460EX/GT")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the mtu is currently not supported in the ibmvnic driver.
Implement .ndo_change_mtu in the driver so that attempting to use ifconfig
to change the mtu will fail and present the user with an error message.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original author left the project and so far has not
responded to emails sent to the listed address.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ibmvnic driver is resetting, we can just reset the sub crqs
instead of releasing all of their resources and re-allocting them.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting the ibmvnic driver there is not a need to release
and re-allocate the resources for the tx and rx pools. These
resources can just be reset to avoid the re-allocations.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver reset operation occurs there is not a need to release
the CRQ resources and re-allocate them. Instead a reset of the CRQ
will suffice.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not want to process any receive frames if the ibmvnic_poll
routine is invoked while a reset is in process. Also, before
replenishing the rx pools in the ibmvnic_poll, we want to
make sure the adapter is not in the process of closing.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If H_CLOSED is returned, halt RX buffer replenishment activity
until firmware sends a notification that the driver can reset.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables transmissions and reports carrier off if xmit
function returns that the hardware TX queue is closed. The driver can
then await a signal from firmware to determine the correct reset method.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle non-fatal error conditions. The process to do this when
resetting the driver is to just do __ibmvnic_close followed by
__ibmvnic_open.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A race condition occurs when closing the driver. Free'ing of skb's
can race between the close routine and ibmvnic_tx_interrupt. To fix
this we move the claenup of tx pools during close to after the
sub-CRQ interrupts are disabled.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle case where phyp sends a failover after failing to send the
init crq.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track the state of ibmvnic napis. The driver can get into states where it
can be reset when napis are already disabled and attempting to disable them
again will cause the driver to hang.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current largesend and checksum offload feature in ibmveth driver,
- Source VM sends the TCP packets with ip_summed field set as
CHECKSUM_PARTIAL and TCP pseudo header checksum is placed in
checksum field
- CHECKSUM_PARTIAL flag in SKB will enable ibmveth driver to mark
"no checksum" and "checksum good" bits in transmit buffer descriptor
before the packet is delivered to pseries PowerVM Hypervisor
- If ibmveth has largesend capability enabled, transmit buffer descriptors
are market accordingly before packet is delivered to Hypervisor
(along with mss value for packets with length > MSS)
- Destination VM's ibmveth driver receives the packet with "checksum good"
bit set and so, SKB's ip_summed field is set with CHECKSUM_UNNECESSARY
- If "largesend" bit was on, mss value is copied from receive descriptor
into SKB's gso_size and other flags are appropriately set for
packets > MSS size
- The packet is now successfully delivered up the stack in destination VM
The offloads described above works fine for TCP communication among VMs in
the same pseries server ( VM A <=> PowerVM Hypervisor <=> VM B )
We are now enabling support for OVS in pseries PowerVM environment. One of
our requirements is to have ibmveth driver configured in "Trunk" mode, when
they are used with OVS. This is because, PowerVM Hypervisor will no more
bridge the packets between VMs, instead the packets are delivered to
IO Server which hosts OVS to bridge them between VMs or to external
networks (flow shown below),
VM A <=> PowerVM Hypervisor <=> IO Server(OVS) <=> PowerVM Hypervisor
<=> VM B
In "IO server" the packet is received by inbound Trunk ibmveth and then
delivered to OVS, which is then bridged to outbound Trunk ibmveth (shown
below),
Inbound Trunk ibmveth <=> OVS <=> Outbound Trunk ibmveth
In this model, we hit the following issues which impacted the VM
communication performance,
- Issue 1: ibmveth doesn't support largesend and checksum offload features
when configured as "Trunk". Driver has explicit checks to prevent
enabling these offloads.
- Issue 2: SYN packet drops seen at destination VM. When the packet
originates, it has CHECKSUM_PARTIAL flag set and as it gets delivered to
IO server's inbound Trunk ibmveth, on validating "checksum good" bits
in ibmveth receive routine, SKB's ip_summed field is set with
CHECKSUM_UNNECESSARY flag. This packet is then bridged by OVS (or Linux
Bridge) and delivered to outbound Trunk ibmveth. At this point the
outbound ibmveth transmit routine will not set "no checksum" and
"checksum good" bits in transmit buffer descriptor, as it does so only
when the ip_summed field is CHECKSUM_PARTIAL. When this packet gets
delivered to destination VM, TCP layer receives the packet with checksum
value of 0 and with no checksum related flags in ip_summed field. This
leads to packet drops. So, TCP connections never goes through fine.
- Issue 3: First packet of a TCP connection will be dropped, if there is
no OVS flow cached in datapath. OVS while trying to identify the flow,
computes the checksum. The computed checksum will be invalid at the
receiving end, as ibmveth transmit routine zeroes out the pseudo
checksum value in the packet. This leads to packet drop.
- Issue 4: ibmveth driver doesn't have support for SKB's with frag_list.
When Physical NIC has GRO enabled and when OVS bridges these packets,
OVS vport send code will end up calling dev_queue_xmit, which in turn
calls validate_xmit_skb.
In validate_xmit_skb routine, the larger packets will get segmented into
MSS sized segments, if SKB has a frag_list and if the driver to which
they are delivered to doesn't support NETIF_F_FRAGLIST feature.
This patch addresses the above four issues, thereby enabling end to end
largesend and checksum offload support for better performance.
- Fix for Issue 1 : Remove checks which prevent enabling TCP largesend and
checksum offloads.
- Fix for Issue 2 : When ibmveth receives a packet with "checksum good"
bit set and if its configured in Trunk mode, set appropriate SKB fields
using skb_partial_csum_set (ip_summed field is set with
CHECKSUM_PARTIAL)
- Fix for Issue 3: Recompute the pseudo header checksum before sending the
SKB up the stack.
- Fix for Issue 4: Linearize the SKBs with frag_list. Though we end up
allocating buffers and copying data, this fix gives
upto 4X throughput increase.
Note: All these fixes need to be dropped together as fixing just one of
them will lead to other issues immediately (especially for Issues 1,2 & 3).
Signed-off-by: Sivakumar Krishnasamy <ksiva@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function __ibmvnic_reset()
in the error handling case.
Fixes: ed651a1087 ("ibmvnic: Updated reset handling")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restart of the subqueue should occur outside of the loop processing
any tx buffers instead of doing this in the middle of the loop.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Map each RX SKB to the RX queue associated with the driver's RX SCRQ.
This should improve the RX CPU load balancing issues seen by the
performance team.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not a need to stop processing skbs if we encounter a
skb that has a receive completion error.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the check for the driver resetting to the first thing
in ibmvnic_xmit().
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When closing the ibmvnic driver we need to wait for any pending
sub crq entries to ensure they are handled.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When closing the ibmvnic driver, most notably during the reset
path, the tx pools need to be cleaned to ensure there are no
hanging skbs that need to be free'ed.
The need for this was found during debugging a loss of network
traffic after handling a driver reset. The underlying cause was
some skbs in the tx pool that were never free'ed. As a
result the upper network layers never tried a re-send since it
believed the driver still had the skb.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi structs allocated at drivier initializatio need to be
free'ed when releasing the drivers resources.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic driver has multiple handlers for resetting the driver
depending on the reason the reset is needed (failover, lpm,
fatal erors,...). All of the reset handlers do essentially the same
thing, this patch moves this work to a common reset handler.
By doing this we also allow the driver to better handle situations
where we can get a reset while handling a reset.
The updated reset handling works by adding a reset work item to the
list of resets and then scheduling work to perform the reset. This
step is necessary because we can receive a reset in interrupt context
and we want to handle the reset out of interrupt context.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the is_closed flag in the ibmvnic adapter strcut with a
more comprehensive state field that tracks the current state of
the driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all of the calls to initialize resources for the driver to
a separate routine.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sub crq structures are initialized in interrupt context while
handling the response to crqs when negotiating capabilities for
the driver. The sub crqs do not need to be initialized at this point
and can be moved to being done from ibmvnic_init. Moving the init
of the sub crqs to ibmvnic_init also allows use to allocate the
memory with GFP_KERNEL instead of GFP_ATOMIC.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the sending of capability request crqs and the initialization
of sub crqs into their own routines. This is a first step to moving
the allocation of sub-crqs out of interrupt context.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an error is encountered during transmit we need to free the
skb instead of returning TX_BUSY.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate that the napi structs exist before trying to disable them
at driver close.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a common routine for setting the link state for the vnic adapter.
This update moves the sending of the crq and waiting for the link state
response to a common place. The new routine also adds handling of
resending the crq in cases of getting a partial success response.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should be initializing the stats token in the same place we
initialize the other resources for the driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling a fatal error in the driver, there can be additional
error information provided by the vios. This information is not
always present, so only retrieve the additional error information
when present.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a modification in the PAPR+ specification which now
defines a previously reserved value for vNIC capabilities. It indicates
whether the system firmware performs a VLAN header stripping on all VLAN
tagged received frames, in case it does, the behavior expected is for
the ibmvnic driver to be responsible for inserting the VLAN header.
Reported-by: Manvanthara B. Puttashankar <mputtash@in.ibm.com>
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Along with 5 TX queues, 5 RX queues are allocated at the beginning of
device probe. However, only the real number of TX queues is set. Configure
the real number of RX queues as well.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bounce buffer is not used in the ibmvnic driver, just
get rid of it.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the allocation of memory for the sub crq structs and their
associated pages to allocate zero-filled memory.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be releasing the crq's when calling close for the
adapter, these need to remain open to facilitate operations such
as updating the mac address. The crq's should be released in the
adpaters remove routine.
Additionally, we need to call release_reources from remove. This
corrects the scenario of trying to remove an adapter that has only
been probed.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inflight list used to track memory that is allocated for crq that are
inflight is not needed. The one piece of the inflight list that does need
to be cleaned at module exit is the error buffer list which is already
attached to the adapter struct.
This patch removes the inflight list and moves checking the error buffer
list to ibmvnic_remove.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the primary CRQ is only used for service functions and
not in the performance path, simplify the code a bit and avoid
disabling the IRQ.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a couple of modifications of an atomic followed
by a read of the atomic, which is no longer atomic, to
use atomic_XX_return variants to avoid race conditions.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we unregister long term buffers from the adapter
prior to DMA unmapping it and freeing the buffer. Failure
to do so could result in a DMA to a now invalid address.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic_change_mac_addr struct alignment was not matching the defined
format in PAPR+, it had the reserved and return code fields swapped. As a
consequence, the CHANGE_MAC_ADDR_RSP commands were being improperly handled
and executed even when the operation wasn't successfully completed by the
system firmware.
Also changing the endianness of the debug message to make it easier to
parse the CRQ content.
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reporting of errors when releasing sub-crqs fails.
Signed-off-by: Thomas Falcon <tlfalcon@us.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in
struct emac_instance, use stats from struct net_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit d6580a9f15 ("kexec: sysrq: simplify sysrq-c handler"),
the sysrq handler for the 'c' key has been sysrq_crash_op. Debugging
code in the ibm_emac driver also tries to register a handler for the 'c'
key, but this has no effect because register_sysrq_key() doesn't replace
existing handlers. Since evidently no one has cared enough to fix this
in the last 8 years, and it's very rare for drivers to register sysrq
handlers (for good reason), just remove the dead code.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ibmvnic_release_resources will clean up all of our resources
properly, even if they were not allocated, we can just call this
for failues in ibmvnic_open.
This patch also moves the ibmvnic_release_resources() routine up
in the file to avoid creating a forward declaration ad re-names it to
drop the ibmvnic prefix.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create an initialization and a release routine for the stats token used by
the ibmvnic driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keeping two routines for releasing sub crqs, one for when irqs are not
initialized and one for when they are, is a bit of overkill. Merge the
two routines to a common release routine that will check for an irq
and release it if needed.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the initialization and the release of the rx pool to their own
routines, and update them to do validation.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the initialization and the release of the tx pool to their own routines,
and update them to do validation. This also adds validation to the release
of the long term buffer.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the handling of initialization and releasing the bounce buffer to their
own init and release routines.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the initialization and release routines for the crq queue so that
we validate the crq queue.
Additionally this updates the naming of the init and release routines
for the crq queue to drop the ibmvnic prefix. This matches the naming
for similar routines in the driver
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debugfs support in the ibmvnic driver is not, and never has been,
supported. Just remove it.
The work done in the debugfs code for the driver was part of the original
spec for the ibmvnic driver. The corresponding support for this from the
server side was never supported and has been dropped.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic driver keeps its statistics in net_device->stats, so the
net_stats member in struct ibmvnic_adapter is unused. Remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmveth driver keeps its statistics in net_device->stats, so the
stats member in struct ibmveth_adapter is unused. Remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When closing the ibmvnic device we need to release the resources used
in communicating to the virtual I/O server. These need to be
re-negotiated with the server at open time.
This patch moves the releasing of resources a separate routine
and updates the open and close handlers to release all resources at
close and re-negotiate and allocate these resources at open.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intialization of the ibmvnic driver with respect to the virtual
server it connects to should be moved to its own routine. This will
alolow the driver to initiate this process from places outside of
the drivers probe routine.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code that handles login and renegotiation of ibmvnic
capabilities to its own routine.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VNIC server expects LINK_STATE_UP to be sent within 30s of the login. If we
exceed the timeout, VNIC server will attempt to fail over. Since time
between probe and open of the device is indeterminate, move login and queue
negotiation into ibmvnic open so we can guarantee that login and sending
LINK_STATE_UP occur within the 30s window.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer array for the tx/rx sub crqs should be free'ed when
releasing the tx/rx sub crqs.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Margetson reported a panic on his SAM460EX with Kernel 4.11-rc1:
| Unable to handle kernel paging request for data at address 0x00000014
| Oops: Kernel access of bad area, sig: 11 [#1]
| PREEMPT
| Canyonlands
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper Not tainted [...]
| task: ea838000 task.stack: ea836000
| NIP: c0599f5c LR: c0599dd8 CTR: 00000000
| REGS: ea837c80 TRAP: 0300 Not tainted [...]
| MSR: 00029000 <CE,EE,ME>
| CR: 24371242 XER: 20000000
| DEAR: 00000014 ESR: 00000000
| GPR00: c0599ce8 ea837d30 ea838000 c0e52dcc c0d56ffb [...]
| NIP [c0599f5c] emac_probe+0xfb4/0x1304
| LR [c0599dd8] emac_probe+0xe30/0x1304
| Call Trace:
| [ea837d30] [c0599ce8] emac_probe+0xd40/0x1304 (unreliable)
| [ea837d80] [c0533504] platform_drv_probe+0x48/0x90
| [ea837da0] [c0531c14] driver_probe_device+0x15c/0x2c4
| [ea837dd0] [c0531e04] __driver_attach+0x88/0xb0
| ---[ end trace ... ]---
The problem is caused by emac_dt_phy_probe() returing success (0)
for existing device-trees configurations that do not specify a
"phy-handle" property. This caused the code to skip the existing
phy probe and setup. Which led to essential phy related
data-structures being uninitialized.
This patch also removes the unused variable in emac_dt_phy_connect().
Fixes: a577ca6bad ("net: emac: add support for device-tree based PHY discovery and setup")
Reported-by: Julian Margetson <runaway@candw.ms>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The amount of TX/RX buffers that the vNIC driver currently allocates
is different from the amount agreed upon in negotiation with firmware.
Correct that by allocating the requested number of buffers confirmed
by firmware.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a counter to track the number of outstanding transmissions sent
that have not received completions. If the counter reaches the maximum
number of queue entries, stop transmissions on that queue. As we receive
more completions from firmware, wake the queue once the counter reaches
an acceptable level.
This patch prevents hardware/firmware TX queue from filling up and
and generating errors. Since incorporating this fix, internal testing
has reported that these firmware errors have stopped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds glue-code that allows the EMAC driver to interface
with the existing dt-supported PHYs in drivers/net/phy.
Because currently, the emac driver maintains a small library of
supported phys for in a private phy.c file located in the drivers
directory.
The support is limited to mostly single ethernet transceiver like the:
CIS8201, BCM5248, ET1011C, Marvell 88E1111 and 88E1112, AR8035.
However, routers like the Netgear WNDR4700 and Cisco Meraki MX60(W)
have a 5-port switch (AR8327N) attached to the EMAC. The switch chip
is supported by the qca8k mdio driver, which uses the generic phy
library. Another reason is that PHYLIB also supports the BCM54610,
which was used for the Western Digital My Book Live.
This will now also make EMAC select PHYLIB.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After sending device capability queries and requests to the vNIC Server,
an interrupt is triggered and the responses are written to the driver's
CRQ response buffer. Since the interrupt can be triggered before all
responses are written and visible to the partition, there is a danger
that the interrupt handler or tasklet can terminate before all responses
are read, resulting in a failure to initialize the device.
To avoid this scenario, when capability commands are sent, we set
a flag that will be checked in the following interrupt tasklet that
will handle the capability responses from the server. Once all
responses have been handled, the flag is disabled; and the tasklet
is allowed to terminate.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two different counters were being used for capabilities
requests and queries. These commands are not called
at the same time so there is no reason a single counter
cannot be used.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a tasklet to process queued commands or messages received from
firmware instead of processing them in the interrupt handler. Note that
this handler does not process network traffic, but communications related
to resource allocation and device settings.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error reports received from firmware were not being converted from
big endian values, leading to bogus error codes reported on little
endian systems.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vNIC client driver requests a faulty device setting, the
server returns an acceptable value for the client to request.
This 64 bit value was incorrectly being swapped as a 32 bit value,
resulting in loss of data. This patch corrects that by using
the 64 bit swap function.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, the MTU is set to the maximum value
capable for the backing device. This decision turned out to
be a mistake as it led to confusion among users. The expected
initial MTU value used for other IBM vNIC capable operating
systems is 1500, with the maximum value (9000) reserved for
when Jumbo frames are enabled. This patch sets the MTU to
the default value for a net device.
It also corrects a discrepancy between MTU values received from
firmware, which includes the ethernet header length, and net
device MTU values.
Finally, it removes redundant min/max MTU assignments after device
initialization.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failure path in ibmvnic_open() mistakenly makes a second call
to napi_enable instead of calling napi_disable. This can result
in a BUG_ON for any queues that were enabled in the previous call
to napi_enable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize condition variables prior to invoking any work that can
mark them complete. This resolves a race in the ibmvnic driver where
the driver faults trying to complete an uninitialized condition
variable.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete()
We plan to remove __napi_complete() to reduce NAPI complexity.
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the ibmveth driver in a KVM/QEMU based VM, it currently
always prints out a scary error message like this when it is started:
ibmveth 71000003 (unregistered net_device): unable to change
checksum offload settings. 1 rc=-2 ret_attr=71000003
This happens because the driver always tries to enable the checksum
offloading without checking for the availability of this feature first.
QEMU does not support checksum offloading for the spapr-vlan device,
thus we always get the error message here.
According to the LoPAPR specification, the "ibm,illan-options" property
of the corresponding device tree node should be checked first to see
whether the H_ILLAN_ATTRIUBTES hypercall and thus the checksum offloading
feature is available. Thus let's do this in the ibmveth driver, too, so
that the error message is really only limited to cases where something
goes wrong, and does not occur if the feature is just missing.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include calculations to compute the number of segments
that comprise an aggregated large packet.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:
"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.
We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."
We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.
Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Reviewed-by: David Dai <zdai@us.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory for netdev private data is allocated using kzalloc/vzalloc in
alloc_netdev_mqs, thus there is no need to zero the stats portion of it
again in the driver's probe function.
In any case, the size for the memset is wrong as the stats member is of
type rtnl_link_stats64, not net_device_stats.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop duplicate header seq_file.h from ibmvnic.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This mistake was causing debugfs directory creation
failures when multiple ibmvnic devices were probed.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure was mapped but never subsequently unmapped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the opt_* fields to determine the starting point for negotiating the
number of tx/rx completion queues with the vnic server. These contain the
number of queues that the vnic server estimates that it will be able to
allocate. While renegotiation may still occur, using the opt_* fields will
reduce the number of times this needs to happen and will prevent driver
probe timeout on systems using large numbers of ibmvnic client devices per
vnic port.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ehea driver is missing a call to netif_carrier_off()
before the interface bring-up; this is necessary in order to
initialize the __LINK_STATE_NOCARRIER bit in the net_device state
field. Otherwise, we observe state UNKNOWN on "ip address" command
output.
This patch adds a call to netif_carrier_off() on ehea's net device
open callback.
Reported-by: Xiong Zhou <zhou@redhat.com>
Reference-ID: IBM bz #137702, Red Hat bz #1089134
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Lamparter