All interrupts coming from MUIC were ignored because interrupt source
register was masked.
The Maxim 77693 has a "interrupt source" - a separate register and interrupts
which give information about PMIC block triggering the individual
interrupt (charger, topsys, MUIC, flash LED).
By default bootloader could initialize this register to "mask all"
value. In such case (observed on Trats2 board) MUIC interrupts won't be
generated regardless of their mask status. Regmap irq chip was unmasking
individual MUIC interrupts but the source was masked
Before introducing regmap irq chip this interrupt source was unmasked,
read and acked. Reading and acking is not necessary but unmasking is.
Fixes: 342d669c1e ("mfd: max77693: Handle IRQs using regmap")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Interrupts coming from Maxim77693 MUIC block (MicroUSB Interface
Controller) were not handled at all because wrong regmap was used for
MUIC's regmap_irq_chip.
The MUIC component of Maxim 77693 uses different I2C address thus second
regmap is created and used by max77693 extcon driver. The registers for
MUIC interrupts are also in that block and should be handled by that
second regmap.
However the regmap irq chip for MUIC was configured with default regmap
which could not read MUIC registers.
Fixes: 342d669c1e ("mfd: max77693: Handle IRQs using regmap")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow more than one viperboard to be connected by registering with
PLATFORM_DEVID_AUTO instead of PLATFORM_DEVID_NONE.
The subdevices are currently registered with PLATFORM_DEVID_NONE, which
will cause a name collision on the platform bus when a second viperboard
is plugged in:
viperboard 1-2.4:1.0: version 0.00 found at bus 001 address 004
------------[ cut here ]------------
WARNING: CPU: 0 PID: 181 at /home/johan/work/omicron/src/linux/fs/sysfs/dir.c:31 sysfs_warn_dup+0x74/0x84()
sysfs: cannot create duplicate filename '/bus/platform/devices/viperboard-gpio'
Modules linked in: i2c_viperboard viperboard netconsole [last unloaded: viperboard]
CPU: 0 PID: 181 Comm: bash Tainted: G W 3.17.0-rc6 #1
[<c0016bf4>] (unwind_backtrace) from [<c0013860>] (show_stack+0x20/0x24)
[<c0013860>] (show_stack) from [<c04305f8>] (dump_stack+0x24/0x28)
[<c04305f8>] (dump_stack) from [<c0040fb4>] (warn_slowpath_common+0x80/0x98)
[<c0040fb4>] (warn_slowpath_common) from [<c004100c>] (warn_slowpath_fmt+0x40/0x48)
[<c004100c>] (warn_slowpath_fmt) from [<c016f1bc>] (sysfs_warn_dup+0x74/0x84)
[<c016f1bc>] (sysfs_warn_dup) from [<c016f548>] (sysfs_do_create_link_sd.isra.2+0xcc/0xd0)
[<c016f548>] (sysfs_do_create_link_sd.isra.2) from [<c016f588>] (sysfs_create_link+0x3c/0x48)
[<c016f588>] (sysfs_create_link) from [<c02867ec>] (bus_add_device+0x12c/0x1e0)
[<c02867ec>] (bus_add_device) from [<c0284820>] (device_add+0x410/0x584)
[<c0284820>] (device_add) from [<c0289440>] (platform_device_add+0xd8/0x26c)
[<c0289440>] (platform_device_add) from [<c02a5ae4>] (mfd_add_device+0x240/0x344)
[<c02a5ae4>] (mfd_add_device) from [<c02a5ce0>] (mfd_add_devices+0xb8/0x110)
[<c02a5ce0>] (mfd_add_devices) from [<bf00d1c8>] (vprbrd_probe+0x160/0x1b0 [viperboard])
[<bf00d1c8>] (vprbrd_probe [viperboard]) from [<c030c000>] (usb_probe_interface+0x1bc/0x2a8)
[<c030c000>] (usb_probe_interface) from [<c028768c>] (driver_probe_device+0x14c/0x3ac)
[<c028768c>] (driver_probe_device) from [<c02879e4>] (__driver_attach+0xa4/0xa8)
[<c02879e4>] (__driver_attach) from [<c0285698>] (bus_for_each_dev+0x70/0xa4)
[<c0285698>] (bus_for_each_dev) from [<c0287030>] (driver_attach+0x2c/0x30)
[<c0287030>] (driver_attach) from [<c030a288>] (usb_store_new_id+0x170/0x1ac)
[<c030a288>] (usb_store_new_id) from [<c030a2f8>] (new_id_store+0x34/0x3c)
[<c030a2f8>] (new_id_store) from [<c02853ec>] (drv_attr_store+0x30/0x3c)
[<c02853ec>] (drv_attr_store) from [<c016eaa8>] (sysfs_kf_write+0x5c/0x60)
[<c016eaa8>] (sysfs_kf_write) from [<c016dc68>] (kernfs_fop_write+0xd4/0x194)
[<c016dc68>] (kernfs_fop_write) from [<c010fe40>] (vfs_write+0xb4/0x1c0)
[<c010fe40>] (vfs_write) from [<c01104a8>] (SyS_write+0x4c/0xa0)
[<c01104a8>] (SyS_write) from [<c000f900>] (ret_fast_syscall+0x0/0x48)
---[ end trace 98e8603c22d65817 ]---
viperboard 1-2.4:1.0: Failed to add mfd devices to core.
viperboard: probe of 1-2.4:1.0 failed with error -17
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
rtsx_pci_power_off() is called only from rtsx_pci_suspend(), which isn't
built when PM is disabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The least significat byte of the GPIO value read register
on the STMPE24xx series is on addres 0xA4 not 0xA5. Correct
against datasheet and tested on the STMPE2401 hardware.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Function pci_enable_msix_range() may return negative values for error
conditions. So it's a bug by checking (pci_enable_msix_range() != 0)
for success and causes failure to megaraid driver when MSI is disabled.
[ 16.487267] megaraid_sas 0000:02:00.0: Controller type: iMR
[ 16.487275] genirq: Flags mismatch irq 0. 00000000 (megasas) vs. 00015a00 (tii
mer)
[ 16.487347] megasas: Failed to register IRQ for vector 0.
Fixes: 8ae80ed173 "megaraid: Use pci_enable_msix_range() instead of pci_enable_msix()"
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # 3.17
Connection retries were not being cleaned up correctly if they failed as a
result of link down. Applies on top of drivers-for-3.18.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch fixes an issue with multipath ipr SAS devices which require a
start unit command to be issued following an adapter reset. Without this
patch, paths get marked failed following an adapter reset and since the
error handler never gets invoked to issue the start unit, the paths are
never recovered. Returning FAILED for this case ensures the error
handler wakes up to issue the start unit.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Multipath devices using the TUR path checker need to see the sense
code for a failed TUR command in their device handler. Since commit
14216561e1 we always return success for mid
layer issued TUR commands before calling the device handler, which
stopped the TUR path checker from working.
Move the call to the device handler check sense method before the early
return for TUR commands to give the device handler a chance to intercept
them.
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Setups that use the blk-mq I/O path can lock up if a host with a single
device that has its door locked enters EH. Make sure to only send the
command to re-lock the door to devices that actually were reset and thus
might have lost their state. Otherwise the EH code might be get blocked
on blk_get_request as all requests for non-reset devices might be in use.
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Meelis Roos <meelis.roos@ut.ee>
Tested-by: Meelis Roos <meelis.roos@ut.ee>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Save the patch while we're running on the BSP instead of later, before
the initrd has been jettisoned. More importantly, on 32-bit we need to
access the physical address instead of the virtual.
This way we actually do find it on the APs instead of having to go
through the initrd each time.
Tested-by: Richard Hendershot <rshendershot@mchsi.com>
Fixes: 5335ba5cf4 ("x86, microcode, AMD: Fix early ucode loading")
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Borislav Petkov <bp@suse.de>
Commit 2ed53c0d6c ("x86/smpboot: Speed up suspend/resume by
avoiding 100ms sleep for CPU offline during S3") introduced
completions to CPU offlining process. These completions are not
initialized on Xen kernels causing a panic in
play_dead_common().
Move handling of die_complete into common routines to make them
available to Xen guests.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Cc: tianyu.lan@intel.com
Cc: konrad.wilk@oracle.com
Cc: xen-devel@lists.xenproject.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1414770572-7950-1-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On some Dell Latitude laptops ALPS device or Dell EC send one invalid byte
in 6 bytes ALPS packet. In this case psmouse driver enter out of sync
state. It looks like that all other bytes in packets are valid and also
device working properly. So there is no need to do full device reset, just
need to wait for byte which match condition for first byte (start of
packet). Because ALPS packets are bigger (6 or 8 bytes) default limit is
small.
This patch increase number of invalid bytes to size of 2 ALPS packets which
psmouse driver can drop before do full reset.
Resetting ALPS devices take some time and when doing reset on some Dell
laptops touchpad, trackstick and also keyboard do not respond. So it is
better to do it only if really necessary.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The quirk argument itself was used as iterator, so it cannot be taken
back to the original value, obviously.
Fixes: d4b8fc66f7 ('ALSA: usb-audio: Allow multiple entries for the same iface in composite quirk')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a copy & paste error:
Warning(sound/core/pcm_native.c:1112): Excess function parameter 'state' description in 'snd_pcm_stop_xrun'
The state argument was dropped from snd_pcm_stop_xrun().
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes a null pointer dereference issue incurred by
calling g2d_remove when exynos_drm_platform_probe is failed.
cmdlist_pool of g2d is allocated when g2d sub driver is probed.
So if exynos_drm_platform_probe is failed, the g2d sub driver is
not probed and the cmdlist_pool is still NULL.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch resovles the infinite loop issue incurred
when Exyno drm driver is enabled but all kms drivers
are disabled on Exynos board by returning -EPROBE_DEFER
only in case that there is kms device registered.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch resolves temporarily infinite loop issue incurred
when Exynos drm driver is enabled and multi-platform kernel
is used by registering Exynos drm device object only in case
of Exynos SoC. So this patch will be replaced with more generic
way later.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Black screen, screen corruption, hardware state corruption fixes.
* tag 'drm-intel-fixes-2014-11-07' of git://anongit.freedesktop.org/drm-intel:
drm/i915: safeguard against too high minimum brightness
drm/i915: vlv: fix gunit HW state corruption during S4 suspend
drm/i915: Disable caches for Global GTT.
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CBMO
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: update defconfig for 3.18
arm64: compat: Enable bpf syscall
arm64: psci: fix cpu_suspend to check idle state type for index
Another quiet week:
- A fix to silence edma probe error on non-supported platforms from Arnd
- A fix to enable the PL clock for Parallella, to make mainline usable with
the SDK.
- A somewhat verbose fix for the PLL clock tree on VF610
- Enabling of SD/MMC on one of the VF610-based boards (for testing)
- A fix for i.MX where CONFIG_SPI used to be implicitly enabled and now needs
to be added to the defconfig instead
- Another maintainer added for bcm2835: Lee Jones
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bOlr
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another quiet week:
- a fix to silence edma probe error on non-supported platforms from
Arnd
- a fix to enable the PL clock for Parallella, to make mainline
usable with the SDK.
- a somewhat verbose fix for the PLL clock tree on VF610
- enabling of SD/MMC on one of the VF610-based boards (for testing)
- a fix for i.MX where CONFIG_SPI used to be implicitly enabled and
now needs to be added to the defconfig instead
- another maintainer added for bcm2835: Lee Jones"
* tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: zynq: Enable PL clocks for Parallella
dma: edma: move device registration to platform code
ARM: dts: vf610: add SD node to cosmic dts
MAINTAINERS: update bcm2835 entry
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Pull devicetree bugfix from Grant Likely:
"One buffer overflow bug that shouldn't be left around"
* 'devicetree/merge' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of: Fix overflow bug in string property parsing functions
Pull btrfs fix from Chris Mason:
"It's a one liner for an error cleanup path that leads to crashes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix kfree on list_head in btrfs_lookup_csums_range error cleanup
Here are 3 tiny fixes for 3.18-rc4. One fixes up a long-stading race
condition in the driver core for removing directories in
/sys/devices/virtual/ and the other 2 fix up the wording of a new
Kconfig option that was added in 3.18-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlReZX4ACgkQMUfUDdst+ym9/gCfbVnQzjAEh3OL0I+mTMjAMxhX
AwwAoK1f/ZK02U/vz/u/dpK38LM3FhH+
=Q4mc
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are 3 tiny fixes for 3.18-rc4.
One fixes up a long-stading race condition in the driver core for
removing directories in /sys/devices/virtual/ and the other 2 fix up
the wording of a new Kconfig option that was added in 3.18-rc1"
* tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
sysfs: driver core: Fix glue dir race condition by gdp_mutex
Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlReZfMACgkQMUfUDdst+ylycwCdGD/ZN7f6rBq7EG0YqBngs5zX
AWwAoK+l0zqYCQ6N8s+ZnQ7l1Ijo7HhR
=vEmW
-----END PGP SIGNATURE-----
Merge tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported"
* tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging:iio:ade7758: Remove "raw" from channel name
staging:iio:ade7758: Fix check if channels are enabled in prenable
staging:iio:ade7758: Fix NULL pointer deref when enabling buffer
iio: as3935: allocate correct iio_device size
io: accel: kxcjk-1013: Fix iio_event_spec direction
iio: tsl4531: Fix compiler error when CONFIG_PM_OPS is not defined
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Here are some tiny serial/tty fixes for 3.18-rc4 that resolve some
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlReZmgACgkQMUfUDdst+ymt1wCgj+RYlAC//NhPIjTHmvHHb9gs
8o0AoJErubEEF3VgbAjvQg1lPr8xSHtR
=7Gmf
-----END PGP SIGNATURE-----
Merge tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tiny serial/tty fixes for 3.18-rc4 that resolve some
reported issues"
* tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix pty master poll() after slave closes v2
serial: of-serial: fix uninitialized kmalloc variable
tty/vt: don't set font mappings on vc not supporting this
tty: serial: 8250_mtk: Fix quot calculation
tty: Prevent "read/write wait queue active!" log flooding
tty: Fix high cpu load if tty is unreleaseable
serial: Fix divide-by-zero fault in uart_get_divisor()
Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device ids for
existing drivers. Full details are in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlReZzgACgkQMUfUDdst+ylTIgCdG8L088p1OqgEdcL+J0ceYS51
PQAAn3O4t962htLmX0XuQmfMWTyBqn11
=3auS
-----END PGP SIGNATURE-----
Merge tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device
ids for existing drivers. Full details are in the shortlog"
* tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: Update default usb-storage delay_use value in kernel-parameters.txt
USB: cdc-acm: add quirk for control-line state requests
phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init()
USB: cdc-acm: only raise DTR on transitions from B0
Revert "storage: Replace magic number with define in usb_stor_euscsi_init()"
usb: core: notify disconnection when core detects disconnect
usb: core: need to call usb_phy_notify_connect after device setup
uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models
xhci: no switching back on non-ULT Haswell
USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
MAINTAINERS: Remove duplicate entry for usbip driver
usb: storage: fix build warnings !CONFIG_PM
usb: Remove references to non-existent PLAT_S5P symbol
uas: Add NO_ATA_1X for VIA VL711 devices
xhci: Disable streams on Asmedia 1042 xhci controllers
USB: HWA: fix a warning message
uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model
usb-storage: handle a skipped data phase
...
imx_get_temp might be called before the sensor clock is prepared
thus resulting in a timeout of the first attempt to read temp:
thermal thermal_zone0: failed to read out thermal zone 0
Happened to me on a Utilite Standard with IMX6 Dual SoC.
Reason is that in imx_thermal_probe thermal_zone_device_register
is called before the sensor clock is prepared.
thermal_zone_device_register however calls
thermal_zone_device_update which eventually calls imx_get_temp.
Fix this by preparing the clock before calling
thermal_zone_device_register.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently the composite quirk doesn't work when multiple entries are
assigned to the same interface because it marks the interface as
claimed then checks whether the interface has been already claimed for
the secondary entry. But, if you look at the code, you'll notice that
multiple entries are allowed if the entry is the current interface;
i.e. the current behavior is anyway inconsistent, and this is an
unintended shortcoming.
This patch fixes the problem by marking the relevant interfaces as
claimed after applying the all composite entries. This fix will be
needed for the upcoming enhancements for Digidesign Mbox 1 quirks.
Reviewed-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new helper function snd_pcm_stop_xrun() to the standard sequnce
lock/snd_pcm_stop(XRUN)/unlock by a single call, and replace the
existing open codes with this helper.
The function checks the PCM running state to prevent setting the wrong
state, too, for more safety.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
5th and 6th byte of ALPS trackstick V3 protocol match condition for first
byte of PS/2 3 bytes packet. When driver enters out of sync state and ALPS
trackstick is sending data then driver match 5th, 6th and next 1st bytes as
PS/2.
It basically means if user is using trackstick when driver is in out of
sync state driver will never resync. Processing these bytes as 3 bytes PS/2
data cause total mess (random cursor movements, random clicks) and make
trackstick unusable until psmouse driver decide to do full device reset.
Lot of users reported problems with ALPS devices on Dell Latitude E6440,
E6540 and E7440 laptops. ALPS device or Dell EC for unknown reason send
some invalid ALPS PS/2 bytes which cause driver out of sync. It looks like
that i8042 and psmouse/alps driver always receive group of 6 bytes packets
so there are no missing bytes and no bytes were inserted between valid
ones.
This patch does not fix root of problem with ALPS devices found in Dell
Latitude laptops but it does not allow to process some (invalid)
subsequence of 6 bytes ALPS packets as 3 bytes PS/2 when driver is out of
sync.
So with this patch trackstick input device does not report bogus data when
also driver is out of sync, so trackstick should be usable on those
machines.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.
Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.
Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.
Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
If no freeze_ops is set, trying to enter suspend-to-IDLE will cause a
nice oops in platform_suspend_prepare_late(). Add respective checks to
platform_suspend_prepare_late() and platform_resume_early() functions.
Fixes: a8d46b9e4e (ACPI / sleep: Rework the handling of ACPI GPE wakeup ...)
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull i2c bugfixes from Wolfram Sang:
"One bigger cleanup (FSF address removal) and two bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
Pull irq fixes from Thomas Gleixner:
"Two fixlets for the armada SoC interrupt controller"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: armada-370-xp: Fix MPIC interrupt handling
irqchip: armada-370-xp: Fix MSI interrupt handling
Pull media fixes from Mauro Carvalho Chehab:
"For:
- some regression fixes at the Remote Controller core and imon driver
- a build fix for certain randconfigs with ir-hix5hd2
- don't feed power to satellite system at ds3000 driver init
It also contains some fixes for drivers added for Kernel 3.18:
- some fixes at the new ISDB-S driver, and the corresponding bits to
fix some descriptors for this Japanese TV standard at the DVB core
- two warning cleanups for sp2 driver if PM is disabled
- change the default mode for the new vivid driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] sp2: sp2_init() can be static
[media] dvb:tc90522: fix always-false expression
[media] dvb-core: set default properties of ISDB-S
[media] dvb:tc90522: fix stats report
[media] vivid: default to single planar device instances
[media] imon: fix other RC type protocol support
[media] ir-hix5hd2 fix build warning
[media] ds3000: fix LNB supply voltage on Tevii S480 on initialization
[media] rc5-decoder: BZ#85721: Fix RC5-SZ decoding
[media] rc-core: fix protocol_change regression in ir_raw_event_register
The Fujitsu H730 does not work with crc_enabled = 0, even though the
crc_enabled bit in the firmware version indicated it would. When switching
this value to crc_enabled to 1, the touchpad works. This patch uses DMI to
detect H730.
Reported-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Alfredo Gemma <alfredo.gemma@gmail.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Fujitsu H730 has hardware v4 with a trackpoint. This enables the
elantech_report_trackpoint for v4.
Reported-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Alfredo Gemma <alfredo.gemma@gmail.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This button is treated as a wakeup source, so we need to initialise it
correctly.
Without the device_init_wakeup() call, dev->power.wakeup will
be NULL, and pm_wakeup_event() will do nothing.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull MIPS updates from Ralf Baechle:
"This weeks' round of MIPS bug fixes for 3.18:
- wire up the bpf syscall
- fix TLB dump output for R3000 class TLBs
- fix strnlen_user return value if no NUL character was found.
- fix build with binutils 2.24.51+. While there is no binutils 2.25
release yet, toolchains derived from binutils 2.24.51+ are already
in common use.
- the Octeon GPIO code forgot to offline GPIO IRQs.
- fix build error for XLP.
- fix possible BUG assertion with EVA for CMA"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix build with binutils 2.24.51+
MIPS: R3000: Fix debug output for Virtual page number
MIPS: Fix strnlen_user() return value in case of overlong strings.
MIPS: CMA: Do not reserve memory if not required
MIPS: Wire up bpf syscall.
MIPS/Xlp: Remove the dead function destroy_irq() to fix build error
MIPS: Octeon: Make Octeon GPIO IRQ chip CPU hotplug-aware
Convert the prototypes to return an int in order to support error
handling in these callbacks.
Also, as suggested by Dmitry Torokhov, pass the domain pointer for use
inside the callbacks, and so that they match the existing
power_on/power_off callbacks which currently take the domain pointer.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ khilman: added domain as parameter to callbacks, as suggested by Dmitry ]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When resuming from s2ram on an SMP system without cpufreq operating
points (e.g. there's no "operating-points" property for the CPU node in
DT, or the platform doesn't use DT yet), the kernel crashes when
bringing CPU 1 online:
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
Unable to handle kernel NULL pointer dereference at virtual address 0000003c
pgd = ee5e6b00
[0000003c] *pgd=6e579003, *pmd=6e588003, *pte=00000000
Internal error: Oops: a07 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1246 Comm: s2ram Tainted: G W 3.18.0-rc3-koelsch-01614-g0377af242bb175c8-dirty #589
task: eeec5240 ti: ee704000 task.ti: ee704000
PC is at __cpufreq_add_dev.isra.24+0x24c/0x77c
LR is at __cpufreq_add_dev.isra.24+0x244/0x77c
pc : [<c0298efc>] lr : [<c0298ef4>] psr: 60000153
sp : ee705d48 ip : ee705d48 fp : ee705d84
r10: c04e0450 r9 : 00000000 r8 : 00000001
r7 : c05426a8 r6 : 00000001 r5 : 00000001 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : 20000153 r0 : c0542734
Verify that policy is not NULL before dereferencing it to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 8414809c6a (cpufreq: Preserve policy structure across suspend/resume)
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This update fixes:
- incorrect warnings about i_mutex locking in
pagecache_isize_extended() and updates comments to match expected
locking
- another zero-range bug fix for stray file size updates
- a bunch of fixes for regression in the bulkstat code introduced in
3.17.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8S0c
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This update fixes a warning in the new pagecache_isize_extended() and
updates some related comments, another fix for zero-range
misbehaviour, and an unforntuately large set of fixes for regressions
in the bulkstat code.
The bulkstat fixes are large but necessary. I wouldn't normally push
such a rework for a -rcX update, but right now xfsdump can silently
create incomplete dumps on 3.17 and it's possible that even xfsrestore
won't notice that the dumps were incomplete. Hence we need to get
this update into 3.17-stable kernels ASAP.
In more detail, the refactoring work I committed in 3.17 has exposed a
major hole in our QA coverage. With both xfsdump (the major user of
bulkstat) and xfsrestore silently ignoring missing files in the
dump/restore process, incomplete dumps were going unnoticed if they
were being triggered. Many of the dump/restore filesets were so small
that they didn't evenhave a chance of triggering the loop iteration
bugs we introduced in 3.17, so we didn't exercise the code
sufficiently, either.
We have already taken steps to improve QA coverage in xfstests to
avoid this happening again, and I've done a lot of manual verification
of dump/restore on very large data sets (tens of millions of inodes)
of the past week to verify this patch set results in bulkstat behaving
the same way as it does on 3.16.
Unfortunately, the fixes are not exactly simple - in tracking down the
problem historic API warts were discovered (e.g xfsdump has been
working around a 20 year old bug in the bulkstat API for the past 10
years) and so that complicated the process of diagnosing and fixing
the problems. i.e. we had to fix bugs in the code as well as
discover and re-introduce the userspace visible API bugs that we
unwittingly "fixed" in 3.17 that xfsdump relied on to work correctly.
Summary:
- incorrect warnings about i_mutex locking in pagecache_isize_extended()
and updates comments to match expected locking
- another zero-range bug fix for stray file size updates
- a bunch of fixes for regression in the bulkstat code introduced in
3.17"
* tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
xfs: rework zero range to prevent invalid i_size updates
mm: Remove false WARN_ON from pagecache_isize_extended()
xfs: Check error during inode btree iteration in xfs_bulkstat()
xfs: bulkstat doesn't release AGI buffer on error
Atomicity between xchg and cmpxchg cannot be guaranteed when xchg is
implemented with a swap and cmpxchg is implemented with locks.
Without this, e.g. mcs_spin_lock and mcs_spin_unlock are broken.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Krzysztof Kozlowski