This will be removed in -next so let's drop it from mainline as soon as
we can in order to minimise surprises.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Normally DAPM will power up any connected audio path. This is not ideal
for sidetone paths as with sidetone paths the audio path is not wanted in
itself, it is only desired if the two paths it provides a sidetone between
are both active. If the sidetone path causes a power up then it can be
hard to minimise pops as we first power up either the sidetone or the main
output path and then power the other, with the second power up potentially
introducing a DC offset.
Address this by introducing the concept of a weak path. If a path is marked
as weak then DAPM will ignore that path when walking the graph, though all
the relevant controls are still available to the application layer to allow
these paths to be configured.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In preparation for the new ASoC Dynamic PCM support (AKA DSP support).
The new ASoC Dynamic PCM core allows DAIs to be dynamically re-routed
at runtime between the PCM device end (or Frontend - FE) and the physical DAI
(Backend - BE) using regular kcontrols (just like a hardware CODEC routes
audio in the analog domain). The Dynamic PCM core therefore must be
able to call PCM operations for both the Frontend and Backend(s) DAIs at
the same time.
Currently we have a global pcm_mutex that is used to serialise
the ASoC PCM operations. This patch removes the global mutex
and adds a mutex per RTD allowing the PCM operations to be reentrant and
allow control of more than one DAI at at time. e.g. a frontend PCM hw_params()
could configure multiple backend DAI hw_params() with similar or different
hw parameters at the same time.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some ASoC components depend on other ASoC components to provide clocks and
power resources in order to probe() and vice versa for remove().
Allow components to be ordered so that components can be probed() and removed()
in sequences that conform to their dependencies.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently pcm_new() passes in 3 arguments :- card, pcm and DAI.
Refactor this to only pass in 1 argument (i.e. the rtd) since struct rtd contains
card, pcm and DAI along with other members too that are useful too.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The card callback will get called for each DAPM context in the card so it
can be useful for it to know which device is currently undergoing a
transition.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Rather than a simple flag to say if we want the DAPM context to be at full
power specify the target bias state. This should have no current effect
but is a bit more direct and so makes it easier to change our decisions
about the which bias state to go into in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
A driver for the AK4641 codec used in iPAQ hx4700 and Glofiish M800
among others.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide real card and bus_info instead of hardcoded values.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
struct snd_card *card is present in struct snd_tea575x but never used.
Remove it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
freq_fixup is a constant, no need to hold it in struct snd_tea575x and set in
each driver.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow ASoC machine drivers to register a driver name
and a longname. This allows user space to determine
the flavour of machine driver.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Implement generic read/write functions to access TEA575x tuners. They're now
implemented 4 times (once in es1968 and 3 times in fm801).
This also allows mute to work on all cards.
Also improve tuner detection/initialization.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A future change will allow multiple widgets to be affected by the same
control. For example, a single register bit that controls separate muxes
in both the L and R audio paths.
This change updates the code that handles relevant controls to be able
to iterate over a list of affected widgets. Note that only the put
functions need significant modification to implement the iteration; the
get functions do not need to iterate, nor unify the results, since all
affected widgets reference the same kcontrol.
When creating the list of widgets, always create a 1-sized list, since
the control sharing is not implemented in this change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Future changes will need reference to the kcontrol created for a given
kcontrol_new. Store the created kcontrol values now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A future change will modify struct snd_soc_dapm_widget to store the
actual kcontrol pointers for each kcontrol_new in a field named
kcontrols. Rename the existing kcontrols field to enable this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the creation of the DAPM debugfs directory to snd_soc_dapm_debugfs_init
instead of having the same duplicated code in both codec and card DAPM setup.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The enum texts are supposed to be const char * const []. Without the
second const, it gets compile warnings like
sound/soc/codecs/max98095.c:607:2: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the equalizer and biquad filter controls.
Signed-off-by: Peter Hsiang <peter.hsiang@maxim-ic.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
replace the tab with spaces,
make it align with other paragraphs
Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Those should not be modified (and are not) by the core code, so make them const.
This also makes them consistent with the same members of snd_soc_codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8915 is an ultra low power mobile CODEC designed for smartphones,
featuring a mixture of digital and analogue I/O with flexible mixing
options and advanced low power accessory detection functionality in a
compact package.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow CODEC and card drivers to point to an array of controls from their
driver structure rather than explicitly calling snd_soc_add_controls().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the MAX98095 CODEC driver.
Signed-off-by: Peter Hsiang <peter.hsiang@maxim-ic.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide the top level ASoC core functions for indicating whether
a given register is readable or writable.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
By using struct snd_soc_reg_access for the read/write/vol attributes
of the registers, we provide callbacks that automatically determine whether
a given register is readable/writable or volatile.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is mainly used by the soc-cache code to easily determine the
currently used underlying serial bus. Set SND_SOC_CUSTOM to 1 so we
can distinguish it if it is not initialized or set.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As it has become more common to have to write firmware or similar
large chunks of data to the hardware, add a function to perform
raw bulk writes that bypass the cache. This only handles volatile
registers as we should avoid getting out of sync with the actual
cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's a big no-no to use pgprot_noncached() when mmap'ing such buffers
into userspace since they are mapped cachable in kernel space.
This can cause all sort of interesting things ranging from to garbled
sound to lockups on various architectures. I've observed that usb-audio
is broken on powerpc 4xx for example because of that.
Also remove the now unused snd_pcm_lib_mmap_noncached(). It's
an arch business to know when to use uncached mappings, there's
already hacks for MIPS inside snd_pcm_default_mmap() and other
archs are supposed to use dma_mmap_coherent().
(See my separate patch that adds dma_mmap_coherent() to powerpc)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This stops code that handles widgets generically from attempting to access
registers for these widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
Add a function to dynamically replace a given control. If the
control does not already exist, a third parameter is used to determine
whether to actually add that control. This is useful in cases where
downloadable firmware at runtime can add or replace existing controls.
A separate patch needs to be made to allow ALSA Mixer to render the
replaced controls on the fly.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Improve tea575x-tuner with various good things from radio-maestro:
- extend frequency range to 50-150MHz
- fix querycap(): card name, CAP_RADIO
- improve g_tuner(): CAP_STEREO, stereo and tuned indication
- improve g_frequency(): tuner index checking and reading frequency from HW
- improve s_frequency(): tuner index and type checking
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new API function snd_ctl_activate_id() for activate / inactivate
the control element dynamically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently will ignore prefixes when creating DAPM controls. Since currently
all control creation goes through snd_soc_cnew() we can fix this by factoring
the prefixing into that function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
When multi component systems use DAIless amplifiers which require clocking
configuration it is at best hard to use the current clocking API as this
requires a DAI even though the device may not even have one. Address this
by adding set_sysclk() and set_pll() operations and APIs for CODECs.
In order to avoid issues with devices which could be used either with or
without DAIs make the DAI variants call through to their CODEC counterparts
if there is no DAI specific operation. Converting over entirely would create
problems for multi-DAI devices which offer per-DAI clocking setup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow a slight simplification of CODEC drivers by allowing DAPM routes and
widgets to be provided in a table. They will be instantiated at the end of
CODEC probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This patch adds support for tlv320aic3205 and tlv320aic3254 codecs.
It doesn't include miniDSP support for aic3254.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is run after the DAPM widgets and routes are added, allowing setup
of things like jacks using the routes. The main card probe() is run before
anything else so can't be used for this purpose.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
These will be added after all devices are registered and allow most DAI
init functions in machine drivers to be replaced by simple data.
Regular controls are not supported as the registration function still
works in terms of CODECs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This means that rather than adding the board specific DAPM widgets to a
random CODEC DAPM context they can be added to the card itself which is
a bit cleaner. Previously there only was one DAPM context and it was
tied to the single supported CODEC.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM9081 IRQ output can be either active high or active low and can
support either CMOS or open drain modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some systems wish to use jacks as wake sources. Provide a wake flag in the
GPIO configuration which causes the driver to enable the IRQ as a wake
source.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use AC97 macros (sometimes already existing, or newly added)
instead of error-prone repetition of open-coded values.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the core code where sparse complains. In most cases, this means
just adding annotations to confirm that we indeed want to do the dirty
things we're doing.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* There is no hysteresis enable field in the current datasheet.
* Mic detection threshold field is only 2 bits wide.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds soc-jack support for adding voltage zones and for
detecting jack type
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move Chip Select control out of the CODEC code for CS4271.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide driver data for cards within the card structure. To simplify the
implementation of the PM operations we don't use the struct device driver
data as this is used by the core to retrieve the card in callbacks from
the device model and PM core.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allows drivers to distinguish which subsequence is being notified when
they get called back.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Could just as well live in sysfs but sysfs doesn't have the simple
value export helpers debugfs does.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow hookup of cards registered directly with the core to the PM
operations by exporting the device power management operations to
modules, also exporting the default PM operations since it is
expected that most cards will end up using exactly the same setup.
Note that the callbacks require that the driver data for the card be
the snd_soc_card.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In order to support cards instantiated without using soc-audio remove
the use of the platform device in the card probe() and remove() ops.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The platform device for the card is tied closely to the soc-audio
implementation which we're currently trying to remove in favour of
allowing cards to have their own devices. Begin removing it by
replacing it with the card in the suspend and resume callbacks we
give to cards, also taking the opportunity to remove the legacy
suspend types which are currently hard coded anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
As requested by Takashi and Jaroslav, these arrays should not be in the
header file.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Incorporate changes by Florian Faber into hdspm.c. Code taken from
http://wiki.linuxproaudio.org/index.php/Driver:hdspe
Heavily reworked to mostly comply with the coding standard (whitespace
fixes, line width, C++ style comments)
The code was tested and confirmed to be working on RME RayDAT.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current format selection of FSI-codecs depended on platform information for FSI,
and chip default settings for codecs. It is not understandable/formal method.
This patch modify FSI and FSI-codecs to use snd_soc_dai_set_fmt.
But FSI can use I2S/PCM and SPDIF format today.
It can be selected to I2S/PCM by snd_soc_dai_set_fmt, but can not select SPDIF.
So, this patch change FSI platform information to have DAI/SPDIF mode.
If platform selects DAI mode (default),
FSI-codecs can select I2S/PCM by snd_soc_dai_set_fmt,
and if it is SPDIF mode, FSI become SPDIF format.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have zero users for PGA controls and the core support for them was
removed a while ago so no point in cut'n'pasting them into new macros,
even if it's too much hassle to update the existing ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We generally refer to registers as unsigned ints (including in the
underlying CODEC driver operation).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch add snd_soc_dai_ops :: set_fmt to FSI driver and
select master/slave clock mode by snd_soc_dai_set_fmt on
fsi-xxx.c instead of platform infomation code.
This patch remove fsi_is_master function which is no longer needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added support for CS4271 codec to ASoC.
Signed-off-by: Alexander Sverdlin <subaparts@yandex.ru>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also, update platform_data GPIO handling to have an explicit "don't
touch this pin" option.
Add #defines for the GPIO pin functions.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is primarily needed to avoid writing back to the cache
whenever we are syncing the cache with the hardware. This gives a
performance benefit especially for large register maps.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many modern devices have features such as DC servos which take time to start.
Currently these are handled by per-widget events but this makes it difficult
to paralleise operations on multiple widgets, meaning delays can end up
being needlessly serialised. By providing a callback to drivers when all
widgets of a given type have been handled during a DAPM sequence the core
allows drivers to start operations separately and wait for them to complete
much more simply.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
With larger devices there may be many widgets of the same type in series
in an audio path. Allow drivers to specify an additional level of ordering
within each widget type by adding a subsequence number to widgets and then
splitting operations on widgets so that widgets of the same type but
different sequence numbers are processed separately. A typical example
would be a supply widget which requires that another widget be enabled
to provide power or clocking.
SND_SOC_DAPM_PGA_S() and SND_SOC_DAPM_SUPPLY_S() macros are provided
allowing this to be used with PGAs and supplies as these are the most
commonly affected widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The machine driver can't register the card directly and need to do this thru
soc-audio device creation
This patch allows the register and unregister card to be directly called by
machine drivers
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the soc_probe initializes the card hence it does the card list
initialzation. But if machines directly register the card they would need to
do these steps, so putting them as inline would save lot of code
This patch adds an inline to do list initialzation
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Harsha Priya <harsha.priya@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that all calls to readable_register()/volatile_register() go via
the snd_soc_codec function pointers.
If the default register access table has been given but no functions
for handling readable()/volatile() registers, use the default ones provided
by soc-cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For common scenarios, device drivers can provide a table of all the
registers that are at least either readable/writable/volatile. The idea
is that if a register lookup fails, all of its read/write/vol members
will be zero and will be treated as default. This also reduces the
size of the register access array.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Simplify the use of reg_size, by calculating it once and storing it in
the codec structure for later reference. The value of reg_size is
reg_cache_size * reg_word_size.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Everything else is using snd_soc_ so we should use it here too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
A couple Tegra ASoC drivers will create debugfs entries. Mark requested
these by under debugfs/asoc/ not just debugfs/. To enable this, export
the dentry representing debugfs/asoc/.
Also, rename debugfs_root -> asoc_debugfs_root now it's exported to
prevent potential symbol name clashes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce the helper function snd_ctl_enum_info() to fill out the
elem_info fields for an enumerated control.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This new type is a virtual version of snd_soc_dapm_mux. It is used
when a backing register value is not necessary for deciding which
input path to connect. A simple virtual enumeration control e.g.
SOC_DAPM_ENUM_VIRT() can be exposed to userspace which will be used
to choose which path to connect.
The snd_soc_dapm_virt_mux type ensures that during the initial
path setup, the first (which is also the default) input path will
be connected.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Attempt to minimise audible effects from mixer and mux updates by
implementing the actual register changes between powering down widgets
that have become unused and powering up widgets that are newly used.
This means that we're making the change with the minimum set of widgets
powered, that the input path is connected when we're powering up widgets
(so things like DC offset correction can run with their signal active)
and that we bring things down to cold before switching away. Since
hardware tends to be designed for the power on/off case more than for
dynamic reconfiguration this should minimise pops and clicks during
reconfiguration while active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Power change event like stream start/stop or kcontrol change in a
cross-device path originates from one device but codec bias and widget power
changes must be populated to another devices on that path as well.
This patch modifies the dapm_power_widgets so that all the widgets on a
sound card are checked for a power change, not just those that are specific
to originating device. Also bias management is extended to check all the
devices. Only exception in bias management are widgetless codecs whose bias
state is changed only if power change is originating from that context.
DAPM context test is added to dapm_seq_run to take care of if power sequence
extends to an another device which requires separate register writes.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling widgets from DAPM context is required when extending the ASoC
core to cross-device paths. Even the list of widgets are now kept in
struct snd_soc_card, the widget listing in sysfs and debugs remain sorted
per device.
This patch makes possible to build cross-device paths but does not extend
yet the DAPM to handle codec bias and widget power changes of an another
device.
Cross-device paths are registered by listing the widgets from device A in
a map for device B. In case of conflicting widget names between the devices,
a uniform name prefix is needed to separate them. See commit ead9b91
"ASoC: Add optional name_prefix for kcontrol, widget and route names" for
help.
An example below shows a path that connects MONO out of A into Line In of B:
static const struct snd_soc_dapm_route mapA[] = {
{"MONO", NULL, "DAC"},
};
static const struct snd_soc_dapm_route mapB[] = {
{"Line In", NULL, "MONO"},
};
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling DAPM paths from DAPM context is a first prerequisite when
extending ASoC core to cross-device paths. This patch is almost a nullop and
does not allow to construct cross-device setup but the path clean-up part in
dapm_free_widgets is prepared to remove cross-device paths between a device
being removed and others.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are no users of these and it's not clear what they would do given
the mono flow modelling which DAPM does. If need arises we can add them
again.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In some cases it was not possible to follow the appropiate power
ON/OFF sequence like in cases where the PGA needs to be enabled
before the driver and disabled before the PGA for pop reduction.
Add a widget to support output driver (speaker, haptic, vibra, etc)
drivers where power ON/OFF ordering is important.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch removes some legacy structure definitions which are not using
in current ASoC drivers.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added an optional name member to snd_soc_cache_ops to enable more
sensible diagnostic messages during cache init, exit and sync.
Remove redundant newline in source code.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the machine driver can only do bias level configuration before
the CODEC bias level is brought up. This means that the machine cannot do
any configuration which depends on the CODEC bias level being maintained.
Provide a post-CODEC callback which allows the machine driver to do things
like enable the FLL on a CODEC which is brought down to BIAS_OFF when idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow the CODEC driver structure to be marked const by making all
the APIs that use it do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch allows machine drivers to override the compression type
provided by the codec driver.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure to use codec->reg_def_copy instead of codec_drv->reg_cache_default
wherever necessary. This change is necessary because in the next patch we
move the cache initialization code outside snd_soc_register_codec() and by that
time any data marked as __devinitconst such as the original reg_cache_default
array might have already been freed by the kernel.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The snd_soc_codec_conf struct now holds codec specific configuration
information.
A new configuration option has been added to allow machine drivers to
override the compression type set by the codec driver.
In the absence of providing an snd_soc_codec_conf struct or when providing
one but not setting the compress_type member to anything, the one supplied
by the codec driver will be used instead. In all other cases the one
set in the snd_soc_codec_conf struct takes effect.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that the base value of compress_type starts at 1 so that
we know whether the machine driver has provided a compress_type
for overriding the codec supplied one.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to keep a copy of the compress_type supplied by the codec driver
so that we can override it if necessary with whatever the machine driver
has provided us with. The reason for not modifying the codec->driver
struct directly is that ideally we'd like to keep it const.
Adjust the code in soc-cache and soc-core to make use of the compress_type
member in the snd_soc_codec struct.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We shouldn't be assigning to the driver structure (which really ought
to be const, further patch to follow) though there's unlikely to be any
actual problem except in the unlikely case that two devices with the
same driver but different bus types appear in the same system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Neither drivers nor the core should be fiddling with the actual ops
structure at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add support for the RME HDSP RPM IO box. Changes have been made in the identification of the IO box and the neccessary controls have been added.
Signed-off-by: Florian Faber <faberman@linuxproaudio.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This makes possible to register auxiliary dailess codecs in a machine
driver. Term dailess is used here for amplifiers and codecs without DAI or
DAI being unused.
Dailess auxiliary codecs are kept in struct snd_soc_aux_dev and those codecs
are probed after initializing the DAI links. There are no major differences
between DAI link codecs and dailess codecs in ASoC core point of view. DAPM
handles them equally and sysfs and debugfs directories for dailess codecs
are similar except the pmdown_time node is not created.
Only suspend and resume functions are modified to traverse all probed codecs
instead of DAI link codecs.
Example below shows a dailess codec registration.
struct snd_soc_aux_dev foo_aux_dev[] = {
{
.name = "Amp",
.codec_name = "codec.2",
.init = foo_init2,
},
};
static struct snd_soc_card card = {
...
.aux_dev = foo_aux_dev,
.num_aux_devs = ARRAY_SIZE(foo_aux_dev),
};
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current AP4 FSI set_rate function used bogus clock process
which didn't care enable/disable and clk->usecound.
To solve this issue, this patch also modify FSI driver to call
set_rate with enough options.
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If CONFIG_SND_DYNAMIC_MINORS is used, assign /dev/snd/seq and
/dev/snd/timer the usual static minors, and export specific
module aliases to generate udev module on-demand loading
instructions:
$ cat /lib/modules/2.6.33.4-smp/modules.devname
# Device nodes to trigger on-demand module loading.
microcode cpu/microcode c10:184
fuse fuse c10:229
ppp_generic ppp c108:0
tun net/tun c10:200
uinput uinput c10:223
dm_mod mapper/control c10:236
snd_timer snd/timer c116:33
snd_seq snd/seq c116:1
The last two lines instruct udev to create device nodes, even
when the modules are not loaded at that time.
As soon as userspace accesses any of these nodes, the in-kernel
module-loader will load the module, and the device can be used.
The header file minor calculation needed to be simplified to
make __stringify() (supports only two indirections) in
the MODULE_ALIAS macro work.
This is part of systemd's effort to get rid of unconditional
module load instructions and needless init scripts.
Cc: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no need anymore to include soc.h in soc-dapm.h and soc-dai.h as
drivers are converted to include only soc.h.
Thanks to Lars-Peter Clausen <lars@metafoo.de> for pointing out the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch allows to disable period interrupts which are
not needed when the application relies on a system timer
to wake-up and refill the ring buffer. The behavior of
the driver is left unchanged, and interrupts are only
disabled if the application requests this configuration.
The behavior in case of underruns is slightly different,
instead of being detected during the period interrupts the
underruns are detected when the application calls
snd_pcm_update_avail, which in turns forces a refresh of the
hw pointer and shows the buffer is empty.
More specifically this patch makes a lot of sense when
PulseAudio relies on timer-based scheduling to access audio
devices such as HDAudio or Intel SST. Disabling interrupts
removes two unwanted wake-ups due to period elapsed events
in low-power playback modes. It also simplifies PulseAudio
voice modules used for speech calls.
To quote Lennart "This patch looks very interesting and
desirable. This is something have long been waiting for."
Support for this in hardware drivers is optional.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a need to prefix codec kcontrol, widget and internal route names in
an ASoC machine that has multiple codecs with conflicting names. The name
collision would occur when codec drivers try to registering kcontrols with
the same name or when building audio paths.
This patch introduces optional prefix_map into struct snd_soc_card. With it
machine drivers can specify a unique name prefix to each codec that have
conflicting names with anothers. Prefix to codec is matched with codec
name.
Following example illustrates a machine that has two same codec instances.
Name collision from kcontrol registration is avoided by specifying a name
prefix "foo" for the second codec. As the codec widget names are prefixed
then second audio map for that codec shows a prefixed widget name.
static const struct snd_soc_dapm_route map0[] = {
{"Spk", NULL, "MONO"},
};
static const struct snd_soc_dapm_route map1[] = {
{"Vibra", NULL, "foo MONO"},
};
static struct snd_soc_prefix_map codec_prefix[] = {
{
.dev_name = "codec.2",
.name_prefix = "foo",
},
};
static struct snd_soc_card card = {
...
.prefix_map = codec_prefix,
.num_prefixes = ARRAY_SIZE(codec_prefix),
};
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for rbtree compression when storing the
register cache. It does this by not adding any uninitialized registers
(those whose value is 0). If any of those registers is written
with a nonzero value they get added into the rbtree.
Consider a sample device with a large sparse register map. The
register indices are between [0, 0x31ff]. An array of 12800 registers
is thus created each of which is 2 bytes. This results in a 25kB
region. This array normally lives outside soc-core, normally in the
driver itself. The original soc-core code would kmemdup this region
resulting in 50kB total memory. When using the rbtree compression
technique and __devinitconst on the original array the figures are
as follows. For this typical device, you might have 100 initialized
registers, that is registers that are nonzero by default. We build
an rbtree with 100 nodes, each of which is 24 bytes. This results
in ~2kB of memory. Assuming that the target arch can freeup the
memory used by the initial __devinitconst array, we end up using
about ~2kB bytes of actual memory. The memory footprint will increase
as uninitialized registers get written and thus new nodes created in
the rbtree. In practice, most of those registers are never changed.
If the target arch can't freeup the __devinitconst array, we end up
using a total of ~27kB. The difference between the rbtree and the LZO
caching techniques, is that if using the LZO technique the size of
the cache will increase slower as more uninitialized registers get
changed.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for LZO compression when storing the register
cache. The initial register defaults cache is marked as __devinitconst
and the only change required for a driver to use LZO compression is
to set the compress_type member in codec->driver to SND_SOC_LZO_COMPRESSION.
For a typical device whose register map would normally occupy 25kB or 50kB
by using the LZO compression technique, one can get down to ~5-7kB. There
might be a performance penalty associated with each individual read/write
due to decompressing/compressing the underlying cache, however that should not
be noticeable. These memory benefits depend on whether the target architecture
can get rid of the memory occupied by the original register defaults cache
which is marked as __devinitconst. Nevertheless there will be some memory
gain even if the target architecture can't get rid of the original register
map, this should be around ~30-32kB instead of 50kB.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch introduces the new caching API and migrates the
old caching interface into the new one. The flat register caching
technique does not use compression at all and it is equivalent to
the old caching technique. One can still access codec->reg_cache
directly but this is not advised as that will not be portable
across different caching strategies.
None of the existing drivers need to be changed to adapt to this
caching technique. There should be no noticeable overhead associated
with using the new caching API.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Based on discussion the dapm_pop_time in debugsfs should be per card rather
than per device. Single pop time value for entire card is cleaner when the
DAPM sequencing is extended to cross-device paths.
debugfs/asoc/{card->name}/{codec dir}/dapm_pop_time
->
debugfs/asoc/{card->name}/dapm_pop_time
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There will be need to have sound card specific debugfs entries. This patch
introduces a new debugfs/asoc/{card->name}/ directory but does not add yet
any entries there.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling Dynamic Audio Power Management (DAPM) from codec devices is
required when developing ASoC further. Such as for other ASoC components to
have DAPM widgets or when extending DAPM to handle cross-device paths.
This patch decouples DAPM related variables from struct snd_soc_codec and
moves them to new struct snd_soc_dapm_context that is used to encapsulate
DAPM context of a device. ASoC core and API of DAPM functions are modified
to use DAPM context instead of codec.
This patch does not change current functionality and a large part of changes
come because of structure and internal API changes.
Core implementation is from Liam Girdwood <lrg@slimlogic.co.uk> with some
minor core changes, codecs and machine driver conversions from
Jarkko Nikula <jhnikula@gmail.com>.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Timur Tabi <timur@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
Cc: Daniel Gloeckner <dg@emlix.com>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Facilitating adding trace type stuff. For a first pass add some dev_dbg()
statements into them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
This patch removes the old CONFIG_SYSFS_DEPRECATED_V2 config option,
but it keeps the logic around to handle block devices in the old manner
as some people like to run new kernel versions on old (pre 2007/2008)
distros.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is adding support for alc562[123] codecs. It's based
on the source code available in HP source code and other places.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This reverts commit f6765502f8 and adds
the missing include file.
Signed-off-by: Peter Hsiang <Peter.Hsiang@maxim-ic.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CCR is defined in emu10k1, but SuperH is defined too.
If user use this driver with SuperH, it becomes a double definition.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If we compile the ASoC code with PM disabled, we hit stuff like:
sound/soc/soc-dapm.c: In function 'snd_soc_dapm_suspend_check':
sound/soc/soc-dapm.c:440: warning: unused variable 'codec'
So tweak the stub macro to avoid these issues.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With generic AC97 ASoC glue driver (codec/ac97.c), we get following warning when
the device is registered (slightly stripped the backtrace):
kobject (c5a863e8): tried to init an initialized object, something is seriously
wrong.
[<c00254fc>] (unwind_backtrace+0x0/0xec)
[<c014fad0>] (kobject_init+0x38/0x70)
[<c0171e94>] (device_initialize+0x20/0x70)
[<c017267c>] (device_register+0xc/0x18)
[<bf20db70>] (snd_soc_instantiate_cards+0x924/0xacc [snd_soc_core])
[<bf20e0d0>] (snd_soc_register_platform+0x16c/0x198 [snd_soc_core])
[<c0175304>] (platform_drv_probe+0x18/0x1c)
[<c0174454>] (driver_probe_device+0xb0/0x16c)
[<c017456c>] (__driver_attach+0x5c/0x7c)
[<c0173cec>] (bus_for_each_dev+0x48/0x78)
[<c0173600>] (bus_add_driver+0x98/0x214)
[<c0174834>] (driver_register+0xa4/0x130)
[<c001f410>] (do_one_initcall+0xd0/0x1a4)
[<c0062ddc>] (sys_init_module+0x12b0/0x1454)
This happens because the generic AC97 glue driver creates its codec->ac97 via
calling snd_ac97_mixer(). snd_ac97_mixer() provides own version of
snd_device.register which handles the device registration when
snd_card_register() is called.
To avoid registering the AC97 device twice, we add a new flag to the
snd_soc_codec: ac97_created which tells whether the AC97 device was created by
SoC subsystem.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than block the workqueue by sleeping to do the debounce use delayed
work to implement the debounce time. This should also means that we extend
the debounce time on each new bounce, potentially allowing shorter debounce
times for clean insertions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8962 features five GPIOs, add support for controlling their output
state via gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add the widget for MICBIAS power control and allow configuration of the
microphone bias setup via the platform data for the WM8962. When
microphone status signals are brought out to GPIO this should be
sufficient to enable microphone detection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide an initial hookup for interrupts on the WM8962. Currently we simply
report error status via log messages if an IRQ is provided for the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some devices have more flexible microphone detection and can detect
a wider range of buttons.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Brown